BERGHOF B-PRIMIS ET-PRO Series Instruction Manual

USER HANDBOOK 1.0
B-PRIMIS ET-PRO series

Copyright © Berghof Automation GmbH
Reproduction and duplication of this document and utilisation and communication of its content are pro-
hibited without with our express permission. All rights reserved.
Infringements will result in compensation for damages.
Disclaimer
The content of this document has been checked for conformity with the hardware and software de-
scribed. It is, however, impossible to rule out all discrepancies. As a result, we cannot be held responsi-
ble if the content is not fully compliant. The information in this document is checked regularly and any
necessary corrections are included in subsequent editions. Suggestions for improvement are always
welcome. Subject to technical modifications.
Trademarks
→CANtrol® and CANtrol®-dialog are registered trademarks of Berghof Automation GmbH.
→Microsoft®, Windows® and the Windows® logo are registered trademarks of Microsoft Corp. in the
USA and other countries.
→EtherCAT® is a registered trademark and a patented technology, licensed by Beckhoff Automa-
tion GmbH, Germany.
→CiA® and CANopen® are registered community trademarks of CAN in Automation e. V.
→ARM ® and Cortex ® are registered trademarks of ARM Limited.
→PROFINET® is a registered trademark of PROFIBUS Nutzerorganisation e.V.
→Modbus® is a registered trademark of the Modbus-IDA organisation.
→i.MX6 is a registered trademark of Freescale.
The rights of all companies and company names mentioned in this document as well as products and
product names belong to the respective companies.
Notes about this handbook
This equipment handbook contains information which is specific to the product and valid at the time of
printing.
This equipment handbook is only complete in conjunction with the product-related hardware and soft-
ware manuals required for the specific application.
You can contact us at:
Berghof Automation GmbH
Arbachtalstrasse 26
72800 Eningen
Germany
T +49.7121.894-0
F +49.7121.894-100
Email: [email protected]
www.berghof-automation.com
Berghof Automation GmbH is certified to DIN EN ISO 9001:2015.

USER HANDBOOK 1.0 | B-PRIMIS ET-PRO SERIES
Berghof Automation GmbH | Arbachtalstrasse 26 | 72800 Eningen | Germany | www.berghof-automation.com
S_B-Primis_ET-Pro_DE_1_0_EN_neu.docx
3
Revision log
Version
Date
Description
0.1
26/09/2019
Initial version
0.9
24/04/2020
Catalogue numbers
1.0
18/06/2020
Formatting revised in the document

USER HANDBOOK 1.0 | B-PRIMIS ET-PRO SERIES
Berghof Automation GmbH | Arbachtalstrasse 26 | 72800 Eningen | Germany | www.berghof-automation.com
S_B-Primis_ET-Pro_DE_1_0_EN_neu.docx
4
Table of contents
1. GENERAL INFORMATION .................................................................................................................7
1.1. Notes about this handbook ...............................................................................................................7
1.2. Symbols and visual depictions .........................................................................................................7
1.3. Hazard categories and indications ...................................................................................................8
1.4. Qualified personnel............................................................................................................................9
1.5. Duty of care.........................................................................................................................................9
General ................................................................................................................................................9
1.6. Intended use .....................................................................................................................................10
1.7. Transport and storage .....................................................................................................................11
Transport and storage ........................................................................................................................11
Devices with (rechargeable) batteries ................................................................................................11
Operation ...........................................................................................................................................11
1.8. Unpacking.........................................................................................................................................11
2. SAFETY.............................................................................................................................................12
Safety-related systems.......................................................................................................................12
2.1. Safety instructions ...........................................................................................................................12
Working on the device........................................................................................................................12
3. PRODUCT DESCRIPTION................................................................................................................13
3.1. Overview ...........................................................................................................................................14
3.1.1. B-Primis ET-Pro 4...............................................................................................................................14
3.1.2. -Primis ET-Pro 7.................................................................................................................................15
3.1.3. B-Primis ET-Pro 10/15........................................................................................................................16
3.2. Scope of delivery and accessories.................................................................................................16
Scope of delivery................................................................................................................................16
Accessories........................................................................................................................................16
3.3. Product features...............................................................................................................................17
Assembly............................................................................................................................................17
Processor ...........................................................................................................................................17
Ethernet..............................................................................................................................................17
USB....................................................................................................................................................17
Additional interfaces...........................................................................................................................17
microSD card......................................................................................................................................17
Summary of features..........................................................................................................................17
4. ASSEMBLY .......................................................................................................................................18
4.1. Preparation for installation..............................................................................................................18
4.1.1. ET-Pro 4 dimensions..........................................................................................................................18
4.1.2. ET-Pro 4 installation cut-out ...............................................................................................................19
4.1.3. ET-Pro 7 dimensions..........................................................................................................................20
4.1.4. ET-Pro 7 installation cut-out ...............................................................................................................21
4.1.5. ET-Pro 10 dimensions ........................................................................................................................22
4.1.6. ET-Pro 10 installation cut-out .............................................................................................................23

USER HANDBOOK 1.0 | B-PRIMIS ET-PRO SERIES
Berghof Automation GmbH | Arbachtalstrasse 26 | 72800 Eningen | Germany | www.berghof-automation.com
S_B-Primis_ET-Pro_DE_1_0_EN_neu.docx
5
4.1.7. ET-Pro 15 dimensions........................................................................................................................24
4.1.8. ET-Pro 15 installation cut-out .............................................................................................................25
4.2. Installation ........................................................................................................................................26
4.2.1. DC-Pro 4/7 installation .......................................................................................................................26
4.2.2. ET-Pro 10 installation .........................................................................................................................28
4.2.3. ET-Pro 15 installation .........................................................................................................................30
5. CONNECTION...................................................................................................................................32
5.1. Power supply....................................................................................................................................32
5.1.2. Connecting the power supply .............................................................................................................33
5.1.3. ET-Pro 4/7 power supply ....................................................................................................................33
5.1.4. ET-Pro 10/15 power supply ................................................................................................................34
5.2. Data connections .............................................................................................................................35
5.2.1. Block diagram.....................................................................................................................................35
5.2.2. Ethernet..............................................................................................................................................36
5.2.3. USB....................................................................................................................................................37
6. OPERATION......................................................................................................................................38
6.1. Switching on and off ........................................................................................................................38
6.2. Initial start-up of the network ..........................................................................................................39
6.2.1. VNC client configuration.....................................................................................................................39
6.2.2. Web terminal configuration.................................................................................................................41
6.3. Operation ..........................................................................................................................................43
6.3.1. Status indicators.................................................................................................................................43
6.3.2. microSD card......................................................................................................................................44
6.4. Troubleshooting ...............................................................................................................................45
6.4.1. No network connection.......................................................................................................................45
7. SERVICING / MAINTENANCE..........................................................................................................45
7.1. Maintenance......................................................................................................................................45
7.2. Cleaning ............................................................................................................................................46
7.3. Chemical resistance.........................................................................................................................46
7.3.1. Resistance of the touch screen ..........................................................................................................46
7.3.2. Resistance of the front membrane display .........................................................................................47
8. DISASSEMBLY .................................................................................................................................48
8.1. ET-Pro 4/7 disassembly ...................................................................................................................48
8.2. ET-Pro 10/15 disassembly ...............................................................................................................49
8.3. Disposal ............................................................................................................................................51
9. TECHNICAL DATA............................................................................................................................52
9.1. Type plate..........................................................................................................................................55
9.2. Device variants and identification ..................................................................................................56
9.3. Options and extensions...................................................................................................................56
10. STANDARDS AND CERTIFICATES.................................................................................................57

USER HANDBOOK 1.0 | B-PRIMIS ET-PRO SERIES
Berghof Automation GmbH | Arbachtalstrasse 26 | 72800 Eningen | Germany | www.berghof-automation.com
S_B-Primis_ET-Pro_DE_1_0_EN_neu.docx
6
10.1. Standards..........................................................................................................................................57
10.2. Declaration of conformity................................................................................................................58
11. CUSTOMER SERVICES / ADDRESSES ..........................................................................................59
11.1. Customer services ...........................................................................................................................59
11.2. Addresses.........................................................................................................................................59
12. APPENDIX.........................................................................................................................................60
12.1. Notes on copyright and the software licence ................................................................................60
12.2. List of figures....................................................................................................................................60

USER HANDBOOK 1.0 | B-PRIMIS ET-PRO SERIES
Berghof Automation GmbH | Arbachtalstrasse 26 | 72800 Eningen | Germany | www.berghof-automation.com
S_B-Primis_ET-Pro_DE_1_0_EN_neu.docx
7
1. General information
This user handbook is intended for use by qualified personnel and contains information on the assem-
bly, installation, start-up and maintenance of the device.
1.1. Notes about this handbook
This user handbook is a component of the product and applies to the following devices:
→B-Primis ET-Pro 4
→B-Primis ET-Pro 7
→B-Primis ET-Pro 10
→B-Primis ET-Pro 15
It contains information on the following topics:
→Areas of application
→Safety
→Mechanical design
→Electrical design
→Connections
→Start-up
→Servicing and maintenance
→Decommissioning
→Disposal
Keep this user handbook available alongside the product at all times.
1.2. Symbols and visual depictions
The following symbols and visual depictions are used in this user handbook:
Symbol
Meaning
→…
List entry
…
Individual instruction or list of instructions which can be carried out in
any order.
1. …
2. …
List of instructions which must be carried out in the order given.
Additional product information

USER HANDBOOK 1.0 | B-PRIMIS ET-PRO SERIES
Berghof Automation GmbH | Arbachtalstrasse 26 | 72800 Eningen | Germany | www.berghof-automation.com
S_B-Primis_ET-Pro_DE_1_0_EN_neu.docx
8
Structure of the warnings:
WARNING
Optional:
More
symbols
Type and source of the danger
Brief description and consequences
Preventive measures
1.3. Hazard categories and indications
The following indications are used for warning messages that must be observed to ensure your per-
sonal safety and avoid any damage to property.
The indications have the following meanings:
DANGER
Serious injury or death
Failure to observe the safety measures will result in death or serious injury.
Take preventive measures.
WARNING
Possible serious injury or death
Failure to observe the safety measures may result in death or serious injury.
Take preventive measures.
CAUTION
Possible minor injuries
Failure to observe the safety measures may result in minor injuries.
Take preventive measures.
NOTICE
Possible damage to property
Failure to observe the safety measures may result in damage to property.
Take preventive measures.

USER HANDBOOK 1.0 | B-PRIMIS ET-PRO SERIES
Berghof Automation GmbH | Arbachtalstrasse 26 | 72800 Eningen | Germany | www.berghof-automation.com
S_B-Primis_ET-Pro_DE_1_0_EN_neu.docx
9
1.4. Qualified personnel
The installation, start-up and maintenance of the machine must be carried out by qualified personnel.
For the purposes of this documentation and the safety instructions contained therein, “qualified person-
nel” means trained staff with the authorisation to assemble, install, start up, earth and identify devices,
systems and electrical circuits in accordance with the standards set in safety engineering and who are
familiar with safety concepts in automation engineering.
1.5. Duty of care
General
The user or processor (OEM) must ensure the following:
→The device must only be used for its intended purpose.
→The device must only be used in a perfect, fully functional condition.
→The user handbook must always be kept legible and fully available.
→Only sufficiently qualified and authorised personnel carry out assembly, installation, start-up and
maintenance of the device.
→This authorised personnel must receive regular training in all relevant questions of occupational
health and safety and environmental protection and must be familiar with the contents of this
user handbook, particularly the sections containing safety instructions.
→Any markings or identification labels and safety and warning signs on the device must not be re-
moved and must be kept legible at all times.
→The national and international regulations regarding the operation of machinery and installations
where the device is being used must be observed.
→The user must always be kept abreast of any current relevant information regarding the device
and its use or operation.
→The user is responsible for coordinating the use of the safety-related control components with the
responsible authority and for adhering to its specifications.

USER HANDBOOK 1.0 | B-PRIMIS ET-PRO SERIES
Berghof Automation GmbH | Arbachtalstrasse 26 | 72800 Eningen | Germany | www.berghof-automation.com
S_B-Primis_ET-Pro_DE_1_0_EN_neu.docx
10
1.6. Intended use
The device is a component of a modular automation system for industrial control applications in the
medium to high performance range. It extends the communication options with EtherCAT, Profinet or
Modbus for example.
The automation system is designed for use in overvoltage category I (IEC 364-4-443) for the control
and regulation of machinery and industrial processes in low-voltage installations in accordance with the
following basic conditions:
→Maximum rated supply voltage of 1,000 V AC (50/60 Hz) or 1,500 V DC
→For use in an environment with max. category 2 level of pollution (EN 61010-1).
→For use in a maximum altitude of 2,000 m a.s.l.
→For indoor use in areas not exposed to direct UV radiation
→Max. ambient temperature inside and outside the control cabinet according to the technical spec-
ifications (see “Technical data”).
Correct and safe operation of the automation system requires qualified project planning, proper
transport, storage, installation and use as well as careful maintenance.
The automation system may only be used within the scope of the information and applications speci-
fied in this documentation and associated user handbooks.
The automation system must only be used as follows:
→As intended
→In technically perfect condition
→Without unauthorised modifications
→By qualified users only
Observe the rules of the employers' liability insurance association, the German Technical Inspec-
tion Association (TÜV), the Association of German Electrical Engineers (VDE) or relevant na-
tional regulations.
The device is intended for installation in a suitable installation cut-out in industrial machines and sys-
tems in indoor areas.
During installation, make sure that the existing seal profiles are undamaged.
For operation, refer to the applicable ambient conditions (see “Technical data”).

USER HANDBOOK 1.0 | B-PRIMIS ET-PRO SERIES
Berghof Automation GmbH | Arbachtalstrasse 26 | 72800 Eningen | Germany | www.berghof-automation.com
S_B-Primis_ET-Pro_DE_1_0_EN_neu.docx
11
1.7. Transport and storage
The device is susceptible to impacts, heavy vibrations, moisture and extreme temperatures.
Transport and storage
Protect the device from heavy mechanical stresses during transport.
Always transport the device in its original packaging.
For storage, refer to the applicable ambient conditions (see “Technical data”).
Protect the device from condensation and moisture.
Devices with (rechargeable) batteries
Lithium metal batteries are a hazardous material. According to the manufacturers, they fall under UN
3091 (contained in the device).
Special provision 188 of the ADR can be applied tor transport.
Operation
If the device has been stored or transported in cold weather or under conditions of large fluctua-
tions in temperature, do not start to operate it until it has acclimatised to room temperature for the
place in which it is used.
Wait at least 12 hours after it has reached room temperature before operating the device.
1.8. Unpacking
Upon receipt of the device, make sure that it is undamaged and complete.
Check the packaging for external damage.
If the packaging is seriously damaged or if damage to the contents is evident: do not proceed fur-
ther with opening the packaging; instead immediately inform the transport company and your
supplier.
Remove the packaging and keep it safe for subsequent transport.
Check the contents for evidence of damage in transport.
Check the contents for completeness against the order documentation and keep all delivery doc-
umentation for future reference. The delivery documentation contains important information
about the device and is part of the product.
If you notice any damage in transport or the contents do not match the order: inform the suppliers
immediately.

USER HANDBOOK 1.0 | B-PRIMIS ET-PRO SERIES
Berghof Automation GmbH | Arbachtalstrasse 26 | 72800 Eningen | Germany | www.berghof-automation.com
S_B-Primis_ET-Pro_DE_1_0_EN_neu.docx
12
2. Safety
Safety-related systems
The use of PLC controls in safety-related systems requires specific measures. If a PLC controller is to
be used in a safety-related system, the user must be given comprehensive advice by the PLC manu-
facturer in addition to any available standards or guidelines regarding safety installations.
Before starting work on the devices, switch off all power supplies, including those of connected
peripherals.
Keep all ventilation openings unobstructed.
The failure of certain components in an electronic control system may result in uncontrolled and/or un-
predictable operational behaviour.
All types of failure must be considered at the system level and the associated preventative
measures identified.
If necessary, request information from your automation system provider.
2.1. Safety instructions
The device may only be operated in a flawless condition. Exposed sharp edges pose a risk of injury.
If you detect damage to the front glass of the device, stop operating the device and immediately
disconnect it from the power supply.
Working on the device
Do not start work on the device until all necessary safety precautions have been taken. Take precau-
tions to avoid unforeseeable functional events and movements of the system.
Bring the system into a safe state.
Switch the system and the device off.
Secure the system against being switched on again.
Disconnect the device from the system.
Do not open the device housing.
If it is necessary to work on internal parts of the device, contact the manufacturer (see
“Addresses”).

USER HANDBOOK 1.0 | B-PRIMIS ET-PRO SERIES
Berghof Automation GmbH | Arbachtalstrasse 26 | 72800 Eningen | Germany | www.berghof-automation.com
S_B-Primis_ET-Pro_DE_1_0_EN_neu.docx
13
3. Product description
The operating panels of the B-Primis ET-Pro series are first-class display and input devices with high-
quality frames in analogue-resistive technology, which are connected to a control system for machines
or plants via Ethernet interfaces. The terminal shows CODESYS Web visualisation or CODESYS Tar-
get visualisation, irrespective of whether the visualisation originates from a Berghof PLC control unit or
another compatible CODESYS control unit.
The device’s connection area for all external connections is located at the rear. These devices are in-
tended for installation on a flat surface in a pre-prepared installation cut-out.
All the connections are of the plug-in type.

USER HANDBOOK 1.0 | B-PRIMIS ET-PRO SERIES
Berghof Automation GmbH | Arbachtalstrasse 26 | 72800 Eningen | Germany | www.berghof-automation.com
S_B-Primis_ET-Pro_DE_1_0_EN_neu.docx
14
3.1. Overview
3.1.1. B-Primis ET-Pro 4
Fig. 1: Overview of ET-Pro 4 (rear)
No.
Designation
No.
Designation
1
Display 4.3 inch
X1
Power supply
2
Fastening clip (4 pcs)
X3
USB 2.0
3
Twist-lock catch (4 pcs) 1
X4
Ethernet (ETH0)
S1
No function
X8
Debug interface
LED
LEDs: PWR, Run/Stop, Error
µSD
microSD card connection (for future
applications)
1
Only required for protection rating IP65

USER HANDBOOK 1.0 | B-PRIMIS ET-PRO SERIES
Berghof Automation GmbH | Arbachtalstrasse 26 | 72800 Eningen | Germany | www.berghof-automation.com
S_B-Primis_ET-Pro_DE_1_0_EN_neu.docx
15
3.1.2. -Primis ET-Pro 7
Fig. 2: ET-Pro 7 (at the rear)
No.
Designation
No.
Designation
1
7-inch display
X1
Power supply
2
Fastening clip (6 pcs)
X3
USB 2.0
3
Twist-lock catch (6 pcs) 1
X4
Ethernet (ETH0)
S1
No function
X8
Debug interface
LED
LEDs: PWR, Run/Stop, Error
µSD
microSD card connection (for future
applications)
1
Only required for protection rating IP65

USER HANDBOOK 1.0 | B-PRIMIS ET-PRO SERIES
Berghof Automation GmbH | Arbachtalstrasse 26 | 72800 Eningen | Germany | www.berghof-automation.com
S_B-Primis_ET-Pro_DE_1_0_EN_neu.docx
16
3.1.3. B-Primis ET-Pro 10/15
Fig. 3: ET-Pro 10/15 (rear)
No.
Designation
No.
Designation
1
10.1/15.6-inch display
X8
Debug interface (do not use –for
Berghof service staff only)
2
Earth connection
X10
0
Power supply
X3
USB 2.0
S1
Function key (do not use –for
Berghof service staff only)
X4
Ethernet (ETH0)
LED
LEDs: PWR, Run/Stop, Error
3.2. Scope of delivery and accessories
Scope of delivery
→B-Primis ET-Pro device
Accessories
The following accessories are available as options H001 or separately via the order number.

USER HANDBOOK 1.0 | B-PRIMIS ET-PRO SERIES
Berghof Automation GmbH | Arbachtalstrasse 26 | 72800 Eningen | Germany | www.berghof-automation.com
S_B-Primis_ET-Pro_DE_1_0_EN_neu.docx
17
Order number
Valid for
Remarks
S-02020201-0100
ET-Pro 4
Connector:
2-pin plug-in connector for the
power supply
Weidmüller BLZF 3.50/02/180
ET-Pro 7
ET-Pro 10
ET-Pro 15
3.3. Product features
Assembly
The device is designed for installation in a front panel or in a control cabinet in a rough industrial envi-
ronment.
Processor
In its basic configuration, the device is equipped with an 800 MHz ARM® CPU with a Cortex™ A9 core.
Customer-specific variants are available, which instead of a single core processor are equipped with a
dual core or quad core processor.
Ethernet
The device has an Ethernet interface with 10/100 Mbit/s. This is used for standard Ethernet connec-
tions. The TCP/IP and UDP protocols permit flexible connections to visualisation software, upstream
control units and to the IT infrastructure.
USB
The USB host interface allows a wide range of peripherals to be connected to the device. This allows a
USB thumb drive to be used for updating the application or for downloading data directly.
USB thumb drives with FAT/FAT32 formatting are supported.
If you require support for other USB formats, please contact our Technical Support team.
Additional interfaces
There is also a debugging interface located on the device which is accessible via a 3.5-mm jack plug
with a special cable (contact Customer Services if necessary).
microSD card
The microSD card interface is designed for future applications.
Summary of features
→ARM® CPU with CortexTM-A9 single core (800 MHz; optional dual core or quad core)
→User program and data memory (RAM): 512 MB onboard
→User program memory (flash) 512 MB onboard
→1 USB host interface (USB 2.0)
→1 Ethernet 10/100 Base T interface

USER HANDBOOK 1.0 | B-PRIMIS ET-PRO SERIES
Berghof Automation GmbH | Arbachtalstrasse 26 | 72800 Eningen | Germany | www.berghof-automation.com
S_B-Primis_ET-Pro_DE_1_0_EN_neu.docx
18
4. Assembly
4.1. Preparation for installation
The devices are intended for installation in a rectangular cut-out on a front panel. The support material
must be rigid.
Prerequisites:
→The device must have a clear space of at least 20 mm all round at the rear, to allow sufficient air
circulation.
→The max. surrounding air temperature in the control cabinet must not exceed 55°C during opera-
tion.
→The support material for the installation cut-out must be of the specified thickness (see installa-
tion cut-out) and must be flat and sufficiently stable.
NOTICE
Damage to the device!
Installation on uneven support material can lead to mechanical stresses and cracks in the front face or to
malfunctioning of the touch screen.
Make sure that the mounting points of the device are all in a common plane, with no more than maxi-
mum ±0.5 mm variation.
4.1.1. ET-Pro 4 dimensions
Fig. 4: ET-Pro 4 dimensions

USER HANDBOOK 1.0 | B-PRIMIS ET-PRO SERIES
Berghof Automation GmbH | Arbachtalstrasse 26 | 72800 Eningen | Germany | www.berghof-automation.com
S_B-Primis_ET-Pro_DE_1_0_EN_neu.docx
19
4.1.2. ET-Pro 4 installation cut-out
Fig. 5: ET-Pro 4 installation cut-out
Cut a rectangular installation cut-out in the support material:
Height: 86.8 mm
Width: 123.8 mm
Max. corner radius: 3.0 mm
Optimum thickness of support material:
Protection rating IP65 with twist-lock catches: only at 1.5–3.0 mm
Optimum: 1.5–2.0 mm
Max. 3.0 mm

USER HANDBOOK 1.0 | B-PRIMIS ET-PRO SERIES
Berghof Automation GmbH | Arbachtalstrasse 26 | 72800 Eningen | Germany | www.berghof-automation.com
S_B-Primis_ET-Pro_DE_1_0_EN_neu.docx
20
4.1.3. ET-Pro 7 dimensions
Fig. 6: ET-Pro 7 dimensions