Bethlehem Lights 9'Green Baby Pine IPT Ready Shape Tree Manual

9’Green Baby Pine IPT Ready Shape Tree Instructions
Included Parts:
•Pre-lighted Tree Top (section D)
•Middle Upper Section of Pre-lighted Tree (section C)
•Middle Lower Section of Pre-lighted Tree (section B)
•Bottom Section of Pre-lighted Tree (section A)
•Collapsible Stand with 3 triangular screws attached in a plastic bag.
•Replacement bulbs and fuses.
Caution – Do not overload: Connect a maximum of three series or series parallel connected lighting strings or
decorative outfits to each load fitting. Do not interconnect different types of products. DO NOT PLUG ITEMS INTO
THE OPEN STRAND SOCKETS. NO OTHER PRODUCTS SHOULD BE PLUGGED INTO THE TREE.
NOTE: if your tree includes flocking, it is recommended to adjust your tree with a sheet under it to help contain the
flocking that comes loose. If your tree includes decorative embellishments, please note that some movement is
incurred during shipping but the beauty of the tree will not be diminished.
Setup Instructions:
NOTE: Because our trees use high grade materials to ensure a long lifetime of beauty, wearing long sleeves and
gloves is recommended to protect your arms and hands from branches.
Step 1: Position and Set-Up Tree Stand
A. Place tree stand in desired location.
B. Unfold tree stand until the legs are perpendicular and the screw holes are aligned.
C. Insert the tree screws into the screw holes and turn 3 – 4 rotations only (if the screws are inserted too far you
will not be able to fully insert the tree pole).
D. Plug the tree stand into an extension cord or wall outlet. If your tree has a foot pedal: To turn on the power
to the tree tap the foot switch once. Once you have the bottom section installed correctly the lights will turn
on. To shut off the lights tap it again.
Indoor Use Only
Made in China H201126INST042013
1

Step 2: Insert the Bottom Section into the Tree Stand
A. Remove plastic cap at the end of the metal pole.
B. Locate the notch in the tree stand (use arrow stickers as a guide).
C. Locate the open groove in the bottom section (the bottom section is marked with “A”). Use arrow stickers as
a guide.
D. Insert the bottom tree section (bottom section is marked with “A”) into the stand making sure that the
groove slides into the notch. Arrows will be pointing to each other. The lights will turn on once it drops into
the correct placement.
E. If the lights do not turn on, refer to the Trouble Shooting portion of this document. Do not drive the section
down with force or forcefully turn the section. Doing so may damage the plugs.
F. Let the hinged branches fall into place.
G. Adjust the branch tips for desired appearance (some people chose to perform this step when the tree is fully
assembled).
H. Tighten screws in stand to secure the tree.
Step 3: Insert the Middle Lower Tree Section into the Bottom Tree Section
A. Remove plastic cap at the end of the metal pole.
B. Locate the notch, groove, and arrows as described above.
C. Insert the middle lower section into the bottom section (middle lower section is marked with “B”). Line up
the arrows as described above. The lights will turn on once it drops into the correct placement.
D. Adjust the branch tips for desired appearance (some people chose to perform this step when the tree is fully
assembled) Indoor Use Only
Made in China H201126INST042013
2

Step 4: Insert the Middle Upper Tree Section into the Middle Lower Tree Section
A. Remove plastic cap at the end of the metal pole.
B. Locate the notch, groove, and arrows as described above.
C. Insert the middle upper section into the middle lower section. The middle upper section is marked with “C”.
Line up the arrows as described above. The lights will turn on once it drops into the correct placement.
D. Adjust the branch tips for desired appearance (some people chose to perform this step when the tree is fully
assembled)
Step 5: Shape the Tree Top and Insert into the Middle Upper Section
A. Adjust the tips and shape the treetop before inserting into the middle upper section.
B. Locate the notch, groove, and arrows as described above.
C. Insert treetop into middle upper section (tree top is marked with “D”). Line up the arrows as described
above. The lights will turn on once it drops into the correct placement.
Step 5: Make final adjustments to tree tips and decorate if desired.
Safety First:
•Unplug power supply cord when replacing bulbs and fuses.
•NEVER change fuse with the power supply cord plug in wall duplex.
•Replace with GKI/Bethlehem lights only.
•Avoid touching electric carrying parts with sharp or heavy objects.
•Do not plug other products into the tree plugs.
Care Instructions:
•If your tree has incandescent lights, be sure to replace burnt-out bulbs with replacement bulbs (included) as bulbs
burn out. This will extend the life of the remaining bulbs.
•When not in use store in a cool dry location.
Indoor Use Only
Made in China H201126INST042013
3

Trouble Shooting:
•If a branch or section will not light, check to be sure that all the cords are plugged into the pole. Each section
should be plugged into one socket.
A safety strap has been placed around the plugs to ensure that the plugs do not fall out of the pole during shipping.
This strap easily slides over the plugs to hold them tight. Images shown are for reference only; your tree may differ
slightly.
•If item still fails to light after checking all plugs are plugged in, look for a damaged, missing, or burnt-out bulb.
Replace the bulb with included replacement bulbs.
•If the item still fails to light after checking all plugs are plugged in, check the fuse at the main power cord (part
you plug into the wall socket) – use only 125 volt fuse, 5 amp maximum.
•If your item has a foot pedal, try tapping the foot pedal once to turn on the lights.
Tree Storage:
Step 1: Unplug power cord.
Step 2: Remove decorations.
Step 3: Lift each section directly up.
Step 4: Separate the tree sections (starting at the top). Fold branches up to avoid crushing the tips. You can tie the
branches up to make the sections easier to handle and set up in future years.
Step 5: Unscrew tree stand to release the bottom section. Fold stand and tighten screws back into stand to prevent
losing the screws.
Step 6: Store in cool dry area.
Indoor Use Only
Made in China H201126INST042013
4

Indoor Use Only
Made in China H201126INST042013
5