Polygroup TG76M3BCYP01 User manual

Page 1 of 2
1. Before you start to assemble your tree, choose an appropriate location near a wall outlet.
2. Assemble the tree stand and place on a level surface. (See Fig. A)
TREE ASSEMBLY INSTRUCTIONS
Congratulations on purchasing your new tree from Polygroup®!
This tree comes with Quick Set® technology - allowing you to set up your tree and light it up in minutes!
Carefully follow the instructions below on how to quickly and easily set up your new tree.
Ensure all packaging is removed before assembly and use. Keep tree's light sets unplugged from power before beginning assembly.
Ensure final assembly is upright and stable.
C13 7.5FT PRE-LIT WESTWOOD SPRUCE TREE
MODEL # : TG76M3BCYP01
SKU # : 124331181
Fig. A - Tree Stand Assembly
Click
Pull apart the legs of the stand so that they
are snapped into an x-shape. Place the tree
stand on a level surface.
To close the stand, press the metal button
and fold the legs together.
Fig. B - Tree and Light Assembly
Tree top
Section 2
Section 1
*Electrical Rating For The Tree
(For Indoor Use Only)
Input: AC120V, 60Hz, 0.45A
Output: DC 28V, 0.9A
Align both arrows
in a straight line
before sliding
down to insert
Open the
cap cover
Do Not Tamper
Internal Parts
Foot Pedal
on/off Switch
Adapter
To Be Plugged
Into Wall
Outlet
A
Insert Green
Label Extension
Cord into Adapter
Carefully review all instructions. If you have a problem, call or email the
manufacturer. Tree Warranty is Valid through December 31, 2022.
Email: [email protected]
Phone: [phone]
WARNING:
To reduce the risk of fire and electric shock:
a) Use only the power supply that was provided with this product. Using a different adapter will damage the lights and may
cause fire, or electrical shock hazards.
b) Do not add any light strings or other power supplies other than what has been provided with this product.
c) Do not mount or support strings in a manner that can cut or damage wire insulation.
d) Do not use near candles, heaters, or other similar sources of heat.
e) Do not use candles on tree.
f) Do not use near tubs, sinks, or other wet areas.
g) Artificial trees are made from small fibers that may pose a choking hazard if detached from the branches.Use care around
children and pets.

Page 2 of 2
Top view Side view
Fig. C
SPARE PARTS
Each tree includes hinge pins/washers.
If extra parts are needed, please contact our customer service center.
3. Each tree section is numbered with a sticker. Please identify all sections before assembling.
4. Assemble the tree from bottom to the top. Start with the bottom section and remove the protective cap before inserting into
the assembled stand. Make sure the pole is firmly inserted and secured into the stand.
5. Continue by inserting the upper tree section(s) to the lower section(s) until inserting the tree top.
6. Allow branches to fall into place or gently pull up and out.When adjusting branches, be sure that all wires are free of branch hinges.
7. Plug the adapter into the wall outlet (See Fig. B). Your entire tree should now be lit.
8. Begin to shape the branches and tips working from the bottom to the top. Start with tips farthest from the pole and fan out one
to the right, one to the left and one at the center of the main stem. (See Fig. C)
TROUBLESHOOTING TIPS
For Pre-lit Trees, If The Tree Does Not Illuminate
1. Please check to make sure that all plugs are properly connected and adapter is plugged into the wall outlet.
2.Turning the poles gently to make sure pole to pole are connected into place.
3. Check for loose connection between light string plugs and extension cords.
4.Try stepping on the On/Off switch foot pedal.
1. Extra hinge pins are included for repairing the hinges.Place the branch
into the slot of the bracket.
2. Insert a new hinge pin through the hole and secure using the retainer
washer.(See Fig. E)
Loose Hinge Pin
Fig.E
9. After shaping the entire tree following the previous step, slightly upsweep all branch tips for a uniform look. Shift branches to fill
any gaps.Your Christmas tree is now complete and ready to be decorated.
STORAGE INSTRUCTIONS
1. Unplug the power adapter from the wall outlet first and then remove all ornaments and decorations.
2. Disassemble the tree from the top to the bottom. Start with the tree top and gently lift straight up to remove from section
below and fold all branches toward the pole.
3. Continue by gently lifting straight up each section(s) from the section below and fold all branches
toward the pole until the bottom section is removed from the tree stand.Cover the cap on the
poles to avoid damaging the internal parts. (See Fig. D)
4. Carefully place all tree sections into shipping box and tape it shut.
5.When not in use, please store your tree in a cool, dry place away from sunlight. Exposing your tree
to excessive heat or humidity may damage your tree. Fig. D
For any questions, assistance, or missing parts, Do Not Return To Place Of Purchase. Please contact us at [phone]
or visit our website at www.polygroupstore.com. One of our customer service representatives will be happy to assist you.
TREE ID# IS LOCATED ON END PANEL OF BOX.TREE ID# IS REQUIRED WHEN REQUESTING REPLACEMENT PARTS.
CUSTOMER SERVICE FOR CHRISTMAS TREES
Tree ID#:
Tree UPC#:
Store Purchased:
Specify Problem:
Customer Name:
Address:(No P.O. Boxes)
City & State:
Zip Code:
Day Phone:
Date Purchased: