Bethlehem Lights 6.5’ Balsam Fir IPT Ready Shape Tree User manual

Indoor Use Only
Made in China H196925INST062012
1
6.5’Balsam Fir IPT Ready Shape Tree Instructions
Included Parts:
Pre-lighted Tree Top (section A)
Middle Section of Pre-lighted Tree (section B)
Bottom Section of Pre-lighted Tree (section C)
Collapsible Stand with 3 triangular screws attached in a plastic bag.
Caution –Do not overload: Connect a maximum of three series or series parallel connected lighting strings or
decorative outfits to each load fitting. Do not interconnect different types of products. DO NOT PLUG ITEMS INTO
THE OPEN STRAND SOCKETS. NO OTHER PRODUCTS SHOULD BE PLUGGED INTO THE TREE.
Setup Instructions:
Step 1: Position and Set-Up Tree Stand
A. Place tree stand in desired location.
B. Unfold tree stand until the legs are perpendicular and the screw holes are aligned.
C. Insert the tree screws into the screw holds and turn 3 –4 rotations only (if the screws are inserted too far you
will not be able to fully insert the tree pole).
D. Plug the tree stand into an extension cord or wall outlet. If your tree has a foot pedal: To turn on the power
to the tree tap the foot switch once. Once you have the bottom section in the lights will come on. To shut off
the lights tap it again.

Indoor Use Only
Made in China H196925INST062012
2
Step 2: Insert the Bottom Section into the Tree Stand
A. Remove plastic cap at the end of the metal pole.
B. Locate the notch in the tree stand (use arrow stickers as a guide).
C. Locate the open groove in the bottom section (the bottom section is marked with “C”). Use arrow stickers as
a guide.
D. Insert the bottom tree section (bottom section is marked with “C”) into the stand making sure that the
groove slides into the notch. Arrows will be pointing to each other. The lights will turn on once it drops into
the correct placement.
E. If the lights do not turn on, refer to the Trouble Shooting portion of this document. Do not drive the section
down with force or forcefully turn the section. Doing so may damage the plugs.
F. Let the hinged branches fall into place.
G. Adjust the branch tips for desired appearance (some people chose to perform this step when the tree is fully
assembled).
H. Tighten screws in stand to secure the tree.
Step 3: Insert the Middle Tree Section into the Bottom Tree Section
A. Remove plastic cap at the end of the metal pole.
B. Locate the notch, groove, and arrows as described above.
C. Insert the middle section into the bottom section (lower middle section is marked with “B”). Line up the
arrows as described above. The lights will turn on once it drops into the correct placement.

Indoor Use Only
Made in China H196925INST062012
3
D. Adjust the branch tips for desired appearance (some people chose to perform this step when the tree is fully
assembled)
Step 4: Shape the Tree Top and Insert into the Middle Section
A. Adjust the tips and shape the treetop before inserting into the middle section.
B. Locate the notch, groove, and arrows as described above.
C. Insert treetop into middle section (tree top is marked with “A”). Line up the arrows as described above. The
lights will turn on once it drops into the correct placement.
Step 5: Make final adjustments to tree tips and decorate if desired.
Safety First:
Unplug power supply cord when replacing bulbs and fuses.
NEVER change fuse with the power supply cord plug in wall duplex.
Replace with GKI/Bethlehem LED mini lights only.
Avoid touching electric carrying parts with sharp or heavy objects.
Do not plug other products into the tree plugs.
Care Instructions:
Be sure to replace burnt-out bulbs with replacement bulbs (included) as bulbs burn out. This will extend the life
of the remaining bulbs.
When not in use store in a cool dry location.
Trouble Shooting:
If a branch or section will not light, check to be sure that all the cords are plugged into the pole.
Section A should be plugged into 1 socket
Section B should be plugged into 1 socket
Section C should be plugged into 1 socket

Indoor Use Only
Made in China H196925INST062012
4
A safety strap has been placed around the plugs to ensure that the plugs do not fall out of the pole during shipping.
This strap easily slides over the plugs to hold them tight.
If item still fails to light after checking all plugs are plugged in, look for a damaged, missing, or burnt-out bulb.
Replace the bulb with included replacement bulbs.
If the item still fails to light after checking all plugs are plugged in, check the fuse at the main power cord (part
you plug into the wall socket) –use only 125 volt fuse, 5 amp maximum.
If your item has a foot pedal, try tapping the foot pedal once to turn on the lights.
Tree Storage:
Step 1: Unplug power cord.
Step 2: Remove decorations.
Step 3: Lift each section directly up.
Step 4: Separate the tree sections (starting at the top). Fold branches up to avoid crushing the tips. You can tie the
branches up to make the sections easier to handle and set up in future years.
Step 5: Unscrew tree stand to release the bottom section. Fold stand and tighten screws back into stand to prevent
losing the screws.
Step 6: Store in cool dry area.