Better Homes and Gardens Lana Modern 3-in-1 User manual

Lana Modern 3-in-1 TV Stand
Stock # BH47-084-899-01
U.S. Patent 9,215,927
This item is designed to be a 3-in-1 configuration. Please choose the option that best suits your
needs. DO NOT discard any of the hardware or parts that you will not use on your chosen option.
This will allow you to use this TV Stand in different configurations at a later date, if desired.
ADULT ASSEMBLY REQUIRED
If you have any questions regarding assembly or if parts are missing, DO NOT return this item to
the store where it was purchased. Please call our toll-free customer service number and have
your instructions and parts list ready to provide the model name, part name or factory number:
866-942-5362
Pacific Standard Time: 8:30 a.m. - 4:30 p.m., Monday - Friday
Or visit our web site 24 hours a day, 7 days a week for product assistance at
www.whalenstyle.com
Or e-mail your request to [e-mail]
LOT NUMBER:
DATE PURCHASED: / /
TV
TV
THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION.
PLEASE READ AND KEEP FOR FUTURE REFERENCE.
Date 2018-08-20 Rev. 0001-B

2
MANUFACTURER: Whalen Furniture Manufacturing
CATALOG: Lana Modern 3-in-1 TV Stand
MODEL # BH47-084-899-01
MADE IN CHINA
1. Please read the Assembly Instructions prior to assembling this product.
2. Remove all hardware from the box and sort by size.
3. Check to see that all hardware and parts are present BEFORE assembling.
4. Ask a friend to assist you with the assembly of this furniture.
5. To avoid damage, assemble the product on a sturdy, level and protective surface.
6. Please wait until all steps are completed before fully tightening bolts.
7. Make sure all bolts are tightly fastened before the unit is used.
MAXIMUM RECOMMENDED WEIGHT LOADS
MAXIMUM LOAD 10 lb. (4.5 kg)
GENERAL INFORMATION, TIPS and TRICKS
This product is sold with one set of Tipping Restraint Hardware Kit. You must install the
Tipping Restraint Hardware between the wall and the TV Stand to prevent any accidents or
damages. When properly installed, this restraint can provide protection against the
unexpected tipping of the unit due to small tremors, bumps or climbing. The restraint is only a
deterrent and is not a substitute for proper adult supervision. Use of tip-over restraints may
only reduce, but not eliminate, the risk of tip-over.
HOLDS MOST 42” - 70” FLAT PANEL TVs
MAXIMUM LOAD 135 lb. (61.3 kg)
HOLDS MOST 42” - 70” FLAT PANEL TVs
WITHOUT SWIVELING BRACKET
MAXIMUM LOAD 135 lb. (61.3 kg)
THIS UNIT IS NOT INTENDED FOR USE WITH CRT TVS. USE ONLY WITH FLAT
PANEL TVS AND AUDIO/VIDEO EQUIPMENT MEETING RECOMMENDED SIZE AND WEIGHT
LIMITS. NEVER USE WITH LARGER/HEAVIER THAN RECOMMENDED FLAT PANEL TVS OR
EQUIPMENT. TO AVOID INSTABILITY, PLACE FLAT PANEL TV INTHE CENTRE OF THE UNIT; THE
BASE OF THE TELEVISION MUST BE ABLE TO REST ON THE SUPPORTING SURFACE OF
THE UNIT WITHOUT OVER-HANGING THE EDGES. IMPROPERLY POSITIONED FLAT PANEL
TVS, OR FLAT PANEL TVS OR OTHER EQUIPMENT THAT EXCEED RECOMMENDED SIZE AND
WEIGHT LIMITS COULD FALL OFFOR BREAK THE UNIT,CAUSING POSSIBLE SERIOUS INJURY.
MAXIMUM LOAD 50 lb. (22.7 kg)

3
IMPORTANT
Before you begin: Open, identify and count all parts prior to assembly. Lay out parts on a flat and
non-abrasive surface. You will need the parts identified on page 4, 5 and 6 of this instruction
manual.
NOTE: IT IS VERY IMPORTANT TO USE GLUE WITH DOWELS. EXCESS GLUE CAN BE WIPED
OFF WITH DAMP CLOTH.
Insert the Dowel at least half way by tapping lightly with a rubber mallet, IF NECESSARY.
CAM LOCK SYSTEM OPERATION
HOW THE KNOCK DOWN (KD) ASSEMBLY SYSTEM WORKS
1. Screw the Cam Bolt into the threaded inserts on the panel. Connect both panels together; making
sure Cam Bolt goes into the pre-drilled hole on the end of panel for Cam Lock.
2. Insert the Cam Lock into the pre-drilled large hole on the panel. Make sure the arrow on the face
of Cam Lock faces out and points towards Cam Bolt.
3. Take a Phillips screwdriver and rotate the Cam Lock clockwise to lock the Cam Bolt in place.
You are now ready to assemble the KD unit.
XXFINAL
1 2 43

4
Parts and Hardware List
Please read completely through the instructions and verify that all listed parts and hardware
are present before beginning assembly.
A- Top Panel B- Lower Shelf with Metal Frame C- Drawer Box Back Panel
(Qty. 1) (Qty. 2) (Qty. 1)
D- Front Stretcher (Qty. 1) E- Back Stretcher (Qty. 1) F- Drawer Box Left Side (Qty. 1)
G- Drawer Box Left Front H- Drawer Box Right Side I- Drawer Box Right Front
(Qty. 1) (Qty. 1) (Qty. 1)
J- Fixed Shelf (Qty. 2) K- Partition Panel (Qty. 1) L- Drawer Front (Qty. 2)
M- Drawer Back Panel (Qty. 2) N- Drawer Left Side (Qty. 2) O- Drawer Right Side (Qty. 2)
P- Drawer Bottom Panel (Qty. 2) Q- Drawer Bottom Support (Qty. 2) R- Left Leg (Qty. 1)
S- Right Leg (Qty. 1) T- Top Metal Frame (Qty. 1) U- Floater Post (Qty. 1)

5
Parts and Hardware List
Please read completely through the instructions and verify that all listed parts and hardware
are present before beginning assembly.
V- Back Frame (Qty. 1) W- Swiveling Bracket (Qty. 1) X- Mounting Frame (Qty. 1)
Y- Monitor Bracket (Qty. 2) Z- Cable Wheel (Qty. 2)
(1) Small Cam Lock (2) Large Cam Lock (3) Cam Bolt
(Qty. 10+1 extra) (Qty. 30+1 extra) (Qty. 40+2 extra)
(4) M8 x 30 mm Wood Dowel (5) M6 x 30 mm Wood Dowel (6) M4 x 32 mm Screw
(Qty. 34+1 extra) (Qty. 10+1 extra) (Qty. 24+1 extra)
(7) 1/2” Bolt (Qty. 4+1 extra) (8) 3/4” Bolt (Qty. 10+1 extra) (9) 1-1/4” Bolt (Qty. 12+1 extra)
(10) 1-3/4” Bolt (Qty. 2+1 extra) (11) 2-1/4” Bolt (Qty. 8+1 extra) (12) Hex Nut (Qty. 4+1 extra)
(13) Lock Washer (14) Flat Washer (15) 2-1/2” Lag Bolt
(Qty. 40+2 extra) (Qty. 40+2 extra) (Qty. 4)
YR
YL

6
Parts and Hardware List
Please read completely through the instructions and verify that all listed parts and hardware
are present before beginning assembly.
(16) Large Flat Washer (17) Concrete Anchor (18) Handle and Back Plate
(Qty. 4+1 extra) (Qty. 4) (Qty. 2)
(19) Handle Bolt (20) 2-5/8” Bolt Glue Touch-up Pen
(Qty. 4) (Qty. 4+1 extra) (Qty. 1) (Qty. 1)
Open Wrench 4 mm Hex Wrench 3/16” Hex Wrench Tipping Restraint Hardware Kit (Qty. 1)
(Qty. 1) (Qty. 1) (Qty. 1) (Inside Plastic Bag)
TV Mounting Kit
M4 x 12 mm Bolt (4) M4 x 30 mm Bolt (4) M5 x 12 mm Bolt (4) M5 x 30 mm Bolt (4)
M6 x 12 mm Bolt (4) M6 x 35 mm Bolt (4) M8 x 16 mm Bolt (4) M8 x 40 mm Bolt mm (4)
M4 Lock Washer (4) M5 Lock Washer (4) M6 Lock Washer (4) M8 Lock Washer (4)
Large Spacer (4) Small Spacer (4) M4/M5 Flat Washer (8) M6/M8 Flat Washer (4)
Tools required: Hex wrench, open wrench (provided) and Phillips screwdriver (not provided).

7
Drawer Assembling
1. Unpack the unit and confirm that you have all the hardware and required parts.
2. Fasten one Drawer Back Panel (M) between the Drawer Left and Right Side Panels (N and O)
with four 32 mm Screws (6) and two M6 x 30 mm Wood Dowels (5).
NOTE: It is very important to use a small amount of glue on both ends of dowels.
M4 x 32 mm Screw
(4 used in this step)
⑥
M6 x 30 mm Wood Dowel
(2 used in this step)
⑤
5
6
6
5
O
M
N

8
Drawer Assembling
3. Fasten one Drawer Bottom Support (Q) to the Drawer Back Panel (M) with two 32 mm Screws
(6).
M4 x 32 mm Screw
(2 used in this step)
⑥
Q
6
M
N
O

9
Drawer Assembling
4. Slide one Drawer Bottom Panel (P) into the grooves between the Drawer Left and Right Side
Panels (N and O) until fully inserted into the groove of the Drawer Back Panel (M).
M
Q
O
N
P

10
Drawer Assembling
5. Securely screw five Cam Bolts (3) into the designated small holes on one Drawer Front (L).
6. Fasten the Drawer Front (L) to the Drawer Left and Right Side Panels (N and O) and the
Drawer Bottom Support (Q) with three M6 x 30 mm Wood Dowels (5) and five Small Cam
Locks (1) (Refer to page 3 on Cam Lock system operation supplement). Make sure that the
Drawer Bottom Panel (P) fits securely into the groove of the Drawer Front (L).
Cam Bolt
(5 used in this step)
③
M6 x 30 mm Wood Dowel
(3 used in this step)
⑤
Small Cam Lock
(5 used in this step)
①
L
3
3
3
P
QO
N
L
5
5
5
1
1
1

11
Drawer Assembling
7. Turn the assembled drawer upright. Attach one Handle and one Bake Plate (18) to the front
side of the Drawer Front (L) with the provided Handle Bolts (19).
8. Repeat the same process to assemble the other drawer.
Handle and Back Plate
(1 used in this step)
⑱
Handle Bolt
(2 used in this step)
⑲
L18
19

12
Assembly Instructions
9. Securely screw the Cam Bolts (3) into the designated small holes on the Top Panel (A), Back
Panel (C), Drawer Box Side Panels (F and H) and Drawer Box Front Panels (G and I) using a
Phillips screwdriver.
A
CG
I
FH
3
Cam Bolt
(30 used in this step)
③

13
Assembly Instructions
10.Attach one Fixed Shelf (J) to the Drawer Box Left Side Panel (F) with two M8 x 30 mm Wood
Dowels (4) and two 32 mm Screws (6).
M4 x 32 mm Screw
(2 used in this step)
⑥
M8 x 30 mm Wood Dowel
(2 used in this step)
④
F
J
6
6

14
Assembly Instructions
11.Attach the Drawer Box Left Front (G) to the Fixed Shelf (J) and the Drawer Box Left Side
Panel (F) with three Large Cam Locks (2) and three M8 x 30 mm Wood Dowels (4).
F
J
G
2
2
4
4
Large Cam Lock
(3 used in this step)
②
M8 x 30 mm Wood Dowel
(3 used in this step)
④

15
Assembly Instructions
12.Attach the other Fixed Shelf (J) to the Drawer Box Right Side Panel (H) with two M8 x 30 mm
Wood Dowels (4) and two 32 mm Screws (6).
H
J
6
6
M4 x 32 mm Screw
(2 used in this step)
⑥
M8 x 30 mm Wood Dowel
(2 used in this step)
④

16
Assembly Instructions
13.Attach the Drawer Box Right Front (I) to the Fixed Shelf (J) and the Drawer Box Right Side
Panel (H) with three Large Cam Locks (2) and three M8 x 30 mm Wood Dowels (4).
Large Cam Lock
(3 used in this step)
②
M8 x 30 mm Wood Dowel
(3 used in this step)
④
HJ
I
22
44

17
Assembly Instructions
14.Attach the Front and Back Stretchers (D and E) between the Drawer Box Side Panels (F and
H) with four Large Cam Locks (2) and four M8 x 30 mm Wood Dowels (4).
Large Cam Lock
(4 used in this step)
②
M8 x 30 mm Wood Dowel
(4 used in this step)
④
FJ
H
J
E
D
E
F/H
J
2

18
Assembly Instructions
15.Attach the Partition Panel (K) to the Front and Back Stretchers (D and E) with two M8 x 30 mm
Wood Dowels (4) and two 32 mm Screws (6).
E
D
K
4
6
6
M4 x 32 mm Screw
(2 used in this step)
⑥
M8 x 30 mm Wood Dowel
(2 used in this step)
④

19
Assembly Instructions
16.Attach the Drawer Box Back Panel (C) to the Drawer Box Side Panels (F and H) and the Fixed
Shelves (J) with six Large Cam Locks (2) and six M8 x 30 mm Wood Dowels (4).
FJ
H
J
C
2
4
Large Cam Lock
(6 used in this step)
②
M8 x 30 mm Wood Dowel
(6 used in this step)
④

20
Drawer Assembling
17.Fasten the Drawer Box Back Panel (C) to the Back Stretcher (E) and the Partition Panel (K)
with six 32 mm Screws (6).
M4 x 32 mm Screw
(6 used in this step)
⑥
C
6
6
6
6