BEWISER S1020 User manual

75x75 100x100
200x100 200x200
34”-49”
FLAT/CURVED
LB
KG
22 to 44 lbs
(10 to 20 kg)
Desk Thickness: 0.8-2.4”(20-60mm)
Upper Arm
(X1)
M4x9mm
(X4)
M4x12mm
(X4)
Allen Wrench
(X2)
(3mm)
(5mm)
Base
(X1)
Lower Arm
(X1)
VESA Assembly
(X1)
M6x14mm
(X2)
Base Lock Screw
(X1)
(5mm)
Tighten
Adjust the small screws on the arms to
adjust the arm rotation tightness.
M4x9mm screw is the default VESA
screw size for most monitors and is
designed to be hand-tightened.
M4x12mm screw is provided to
accommodate monitors requiring
longer VESA screws.
Attach the VESA Assembly to the Upper Arm
and secure it with the two M6x14mm screws.
The monitor tilt can now be easily
adjusted by hand.
For Monitors up to 44 lbs/20 kg,
Not for monitors lighter than 22 lbs/10 kg.
Install your monitor.
Ensure the monitor is
facing the right way up.
(5mm)
(3mm)
NOTE: the two mechanical springs inside the VESA Assembly are stiff. It is not
necessary to straighten the VESA Plate tilt by hand before connecting to the monitor.
Adjust tilt after the monitor, VESA Assembly and Upper Arm are all installed.
TOP
M6×14mm
BEWISER Heavy Duty Monitor Arm S1020
INSTALLATION MANUAL
If you have any questions or concerns about this product. Please feel free to email us at [email protected]
Parts List
①
Clamp Installation
②-01
Arm Installation
③
Monitor Installation
④
VESA Assembly Installation
⑤
Grommet Installation
②-02
Tighten
(5mm)
Use Allen Wrench to separate
Base and Clamp
Desk Thickness: 0.8-2.4” (20-60mm)
Grommet Hole Diameter: min 2” (50mm)
Please scan QR code for
installation video.

+
-
-
+
The Base Lock Screw is pre-installed on the Base
Remove the Base Lock Screw 360°
Lower Arm can rotate 180°.
180°
Lower Arm can rotate 360°.
Push
+
Adjust Arm Tension
⑥Cable Management ⑧
Optional Installation – Lower Arm Rotation Lock
⑨
Monitor Tilt Adjustment
⑦
By using the Allen Wrench you can adjust the gas spring tension in the Upper Arm. Adjust the screw counter-clockwise (+) to
increase gas spring tension. Adjust the screw clockwise (-) to decrease gas spring tension.
To avoid any damage and facilitate easy adjustment, hold the arm in a horizontal position during tension adjustment.a.
If the arm rises, turn the adjustment screw clockwise (-) until it stays in a horizontal position.
b.
If the arm droops, turn the adjustment screw counter-clockwise (+) until it stays in a horizontal position.
c.
For extremely heavy monitors, if the monitor tilt does not stop at the desired angle,
please turn the top tension screw counter-clockwise (+) using the Allen Wrench so
that the tilt tension increases to hold the monitor tilt at the desired angle.
It is suggested to adjust the top tension
screw by up to 5 full rotations rst.
Upper Arm Cable Cover:
remove by pushing cover
in direction of the arrow
(some extra force
may be needed).
Lower Arm Cable Cover:
pinch and squeeze
protruding aps of the
cover, then gently
remove.
The Lower Arm rotation lock is used to prevent the monitor arm from swinging into oce divider, screen or wall.
To avoid tipping. DO NOT
position the monitor past
the back of the desk.
CAUTION:
Attention
Note that after all the screws are tightened
according to the instructions, the monitor still
slowly slide to one side. Please check if the table
is slightly tilted. Because the monitor is very
heavy, the table will tilt slightly after installation,
resulting in imbalance of the product lever. You
can try to weigh down the table with some
heavy things to see if this is still the case.
If you still have questions, please contact us.