Sealey VS1003 User manual

IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT
CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL
INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions
and maintained properly, give you years of trouble free performance.
Refer to Instruction
Manual
© Jack Sealey Limited Original Language Version VS1003 Issue: 4(I) - 21/02/17
INSTRUCTIONS FOR:
AXLE STAND 3 TONNE RATCHET TYPE
MODEL No: VS1003
1. SAFETY
WARNING!
DO NOT OVERLOAD AXLE STANDS BEYOND RATED CAPACITY. OVERLOADING CAN CAUSE DAMAGE TO, OR FAILURE OF,
THE AXLE STANDS. POSITION LOAD ON CENTRE OF CRUTCH/SADDLE ONLY. ALWAYS USE STANDS IN PAIRS ON HARD
LEVEL SURFACE CAPABLE OF SUSTAINING THE LOAD. USE OF STANDS ON OTHER THAN HARD LEVEL SURFACES CAN
RESULT IN LOAD INSTABILITY AND POSSIBLE LOSS OF LOAD. DO NOT USE ON TARMACADAM. FAILURE TO FOLLOW
THESE INSTRUCTIONS MAY RESULT IN DAMAGE TO AXLE STANDS, LOSS OF LOAD RESULTING IN PROPERTY DAMAGE,
SERIOUS PERSONAL INJURY OR LOSS OF LIFE.
▲DANGER! GREAT CARE MUST BE TAKEN TO ENSURE YOU LOWER THE VEHICLE (OR OTHER LOAD)
SLOWLY AND CAREFULLY ONTO THE CENTRES OF THE CRUTCH/SADDLE OF THE AXLE STANDS.
9Use only as specified by the manufacturer.
9Ensure the load does not exceed the maximum capacity as marked on the axle stand, per pair.
9Use no more than a single pair of stands either on the front, rear or one side of the vehicle. Use in pairs.
9No alterations or modifications shall be made to this product.
9Use on a hard, level surface, e.g. concrete. DO NOT use on uneven ground or tarmacadam.
9Securely chock wheels in contact with the ground. Before jacking and placing the stands, apply vehicle
handbrake (put automatics in ‘Park’).
9Make sure that each stand is securely located under a strong point on the vehicle; consult the vehicle manufacturer’s handbook for
guidance. Ensure that height adjust locking mechanism is fully located before applying any load to the axle stand.
9Ensure that the load is located centrally on the saddle, and that the weight is directed through the vertical axis of the stand.
9Exercise extra care when using with a three wheeled vehicle or a trailer. Refer to vehicle manufacturer’s instructions.
9Once vehicle is supported, ensure that the vehicle and stands are stable before starting work. Ensure that it is not possible for the
vehicle to move before commencing any work.
9Inspect stands before each use. DO NOT use if they show signs of damage. DO NOT use if it is suspected that they have been
overloaded.
9Before commencing any work or going beneath the vehicle, undertake a risk assessment. Ensure that a responsible person is aware of
the work about to be undertaken.
9Replace any labels on the axle stand should they become unreadable. This applies in particular to any warning or operation instruction
labels. If replacement labels are required, contact your Sealey stockist.
8DO NOT use axle stands on the highway, or anywhere else if it is deemed to be unsafe.
8DO NOT push or twist the vehicle/load whilst it is supported on stands.
8DO NOT mix components between stands. Use only as supplied.
8DO NOT allow children or animals in the vicinity of a vehicle supported on axle stands.
8DO NOT leave a vehicle on axle stands in an area that could be considered a hazard to others or property.
9FOLLOW STEPS 1, 2 AND 3 TO CORRECTLY PLACE VEHICLE/LOAD ONTO AXLE STANDS

2. INTRODUCTION
3. SPECIFICATION
Ratchet type axle stands with cast iron support posts. Feature angled teeth in posts, which prevent accidental release of load - the more weight
applied, the tighter the post is locked.
Capacity (each): .................. 3 tonnes (3,000 kg)
Capacity (pair): ................... 6 tonnes (6,000kg)
Minimum Height: ................. 287mm
Maximum Height: ................. 427mm
4. PREPARATION
4.1. Insert centre column into base of axle stand (Fig.2). Ensure toothed side of column will
engage with locking lever mechanism.
4.2. Bend in locking tab using a small chisel and hammer (Fig.1).
4.3. Check axle stand is in good condition and has not suffered damage during transit.
5. OPERATION
5.1. Refer to vehicle's handbook for correct jacking procedure. Check to ensure
manufacturer’s recommended jacking points are in good condition.
5.2. Position axle stands under jacking points.
5.3. To adjust axle stands: Hold locking lever up, while lifting column to required height. Push
locking lever down to lock pawl into column teeth (Fig.2).
 WARNING! ENSURE PAWL IS FULLY ENGAGED WITH TEETH.
5.4. Lower vehicle onto axle stands carefully and slowly. Ensure load bearing points sit in the
centre of the saddles and that the axle stands are stable.
Also ensure that there are no objects or persons that could impede the safe lowering of
the vehicle onto the stands.
DANGER! You must follow instructions carefully and ensure you DO NOT load the axle
stands off-centre. Failure to heed these warnings may cause damage, injury or loss of life.
Fig.2
Fig.1
Bend tab in
after
inserting
Centre
Column
6.1. Before each use, check that the axle stands and the stand's welds are not cracked and
that there are no missing or damaged parts.
Any suspect axle stand must be removed from service immediately.
6.2. Due to the potential hazards associated with these axle stands, do not misuse, or make any
modification to the axle stands or components.
6.3. It is the responsibility of the owner to ensure that the operator has read these instructions
together with the safety features on the side of the axle stand and that the operator is
familiar with the axle stand’s use and limitations.
6. MAINTENANCE & INSPECTION
01284 757500
01284 703534
[e-mail]
Sole UK Distributor, Sealey Group,
Kempson Way, Suffolk Business Park,
Bury St. Edmunds, Suffolk,
IP32 7AR
www.sealey.co.uk
NOTE: It is our policy to improve products continually and as such we reserve the right to alter data, specifications and component parts without
prior notice.
IMPORTANT: No liability is accepted for incorrect use of this product.
WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required for any claim.
Environmental Protection
Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted, taken to
a recycling centre and disposed of in a manner which is compatible with the environment. When the product becomes completely
unserviceable and requires disposal of it according to local regulations.
Parts support is available for this product. To obtain a parts listing and/or diagram,
please log on to www.sealey.co.uk, email [e-mail] or telephone [phone].
© Jack Sealey Limited Original Language Version VS1003 Issue: 4(I) - 21/02/17