Big Lots BQ096-0774WH User manual

Page 1 of 8
RAINBOW UNICORN DRESS UP TABLE
810582248
BQ096-0774WH

Page 2 of 8
Read all instructions before starting
Clear a flat covered space to begin
Two adults are recommended for assembly
Note that hardware required is provided for every step
Pay attention to orientation
Letter of the part corresponds to a sticker on the product
Number of the hardware corresponds to its number on the package
Helpful hints provided along the way
MAINTENANCE:
WARNINGS:
GENERAL BEST PRACTICES FOR ASSEMBLY:
Regularly check hardware and tighten if necessary.
Use a dry clean cloth to dust or wipe up any spills.
Avoid exposure to water and fire.
SUGGEST 2 ADULTS TO ASSEMBLE THIS PRODUCT IN ANOPEN AREA.
DO NOT USE POWER TOOLS TO ASSEMBLE

Page 3 of 8
NO QTY DESCRIPTION
A 1pc
B1pc
C1pc
D1pc
E1pc
F 2pcs
G 2pcs
H 1pc
2pcs
J 2pcs
1pc
I
Left Mirror with Frame
Middle Mirror with Frame
Side Drawer Panel
Back Drawer Panel
Right Mirror with Frame
Table Top
Wooden Slider
Front Table Leg
Rear Table Leg
Front Drawer Panel
K 2pcs
1pc Bottom Drawer Panel
1pc
M 2pcs
1pc
LWooden Handle
Stool Top
N 2pcs
4pcs Stool Leg
A
F
F
G
G
H
I
I
J
K
L
M
B
C
D
E
N
N
N
N
O
O 2pcs
1pc Stool Back

Page 4 of 8
1
NO QTY
PARTS DESCRIPTION
1
2
3
4
4pcs Metal Connector
1pc Stopper
6pcs Wooden Dowel
16pcs Bolt(6×35mm)
3x
2
4x 8 5x 8 6x 8
5
6
7
16pcs Spring Washer
16pcs Flat Washer
6pcs Screw(4×30mm)
83pcs Screw(4×25mm)
98pcs Screw(3×20mm)
10
11
12
3pcs Screw(3×10mm)
8pcs Screw(3×8mm)
1pc Allen Wrench
N
N
N
N
M
1. Attach Stool Leg (N) to Stool Top (M) with Bolt (4), Spring Washer (5) and Flat Washer (6) using Allen Wrench (12).
Fully tighten bolts.
Note: The position of the Spring Washer (5) and Flat Washer (6) needs to be the same as the diagram below.
2. Insert Wooden Dowel (3) into the end of Stool Back (O) .
3. Align the Wooden Dowels (3) in the end of Stool Back (O) with the holes in the Stool Top (M) and slide into place.
4. Secure the panels together with Screws (7) using Phillips screwdriver (not provided).
12
4
5
77
33
6
M
7x 2 12 x 1
O
• A Phillips Screwdriver will be needed for assembly and is not provided.
• Separate parts before starting

2
4x
8
5x 8 6x 8 12 x 1
Attach Front Table Leg (F) and Rear Table Leg (G) to Table Top (D)
with Bolt (4), Spring Washer (5) and Flat Washer (6) using Allen
Wrench (12) as show in the diagram. Fully tighten bolts.
Note: The position of the Spring Washer (5) and Flat Washer (6)
need to be the same as the diagram below.
F
G
G
F
D
12
4
5
6
Page 5 of 8
8x
2
3
Attach Wooden Slider (E) to Bottom of Table Top (D)
with Screw (8) using Phillips screwdriver (not provided).
D
E
8
8
8
8
Fully tighten screws.

Page 6 of 8
9
9
9
9
9x8
4
I
I
I
JJ
K
H
H
H
8x 1
8
L
1. Attach Wooden Handle (L) to Front Drawer Panel (H) with Screw (8) using Phillips screwdriver (not provided).
Fully tighten screw.
2. Attach Back Drawer Panel (J) and Front Drawer Panel (H) to Side Drawer
Panel (I) with Screw (9) using Phillips
3. Slide Bottom Drawer Panel (K) into the grooves of Front Drawer Panel (H) and Back Drawer Panel (J) until it is
fully inserted into the groove of Side Drawer Panel (I).
4. Place the remaining Side Drawer Panel (I) into position so Bottom Drawer Panel (K) is fully inserted into the groove.
Attach Side Drawer Panel (I) to
Back Drawer Panel (J) and
Front Drawer Panel (H) with Screw (9) using Phillips
5
1
11
1
10
10
10
1x
110 x 3
K
G
G
F
F
J
J
EE
E
1. Slide the Stopper (1) over the Wooden Slider (E).
Note: The flat side of the Stopper should face the assembled Drawer.
2. Secure the Stopper to the Back Drawer Panel (J) with Screws (10)
screwdriver (not provided). Fully tighten screws.
Note: Ensure the bottom of the assembled drawer is on top as shown before
attaching the the Stopper (1)
screwdriver (not provided). Fully tighten screws.
using Phillips
screwdriver (not provided). Fully tighten screws.

Page 7 of 8
7
3x
27x 2
6
B
B
C
G
G
F
F
3x 1 7x 1
D
D
7
7
7
3
3
3
1. Insert Wooden Dowel (3) into the holes of Middle Mirror
with Frame (B).
2. Align the Wooden Dowels (3) in Middle Mirror with
Frame (B) with the holes in Table Top (D) and lower
into place.
3. Secure Table Top (D) to Middle Mirror with Frame (B)
with Screw (7) using Phillips screwdriver (not provided).
Fully tighten screws.
1. Insert Wooden Dowel (3) into the holes of Right Mirror with
Frame (C).
2. Align the Wooden Dowels (3) in Right Mirror with Frame (C)
with the holes in Table Top (D) and lower into place.
3. Secure Table Top (D) to Right Mirror with Frame (C) with
Screw (7) using Phillips screwdriver (not provided).
Fully tighten screws.

Page 8 of 8
9
B
B
C
C
2x
4
11 x 8
D
7
3
A
11
11
11
11 11
2
2
2
2
2
8
3x 1 7x 1
1. Insert Wooden Dowel (3) into the holes of Left Mirror with
Frame (A).
2. Align the Wooden Dowels (3) in Left Mirror with Frame (A)
with the holes in Table Top (D) and lower into place.
3. Secure Table Top (D) to Left Mirror with Frame (A) with
1. Secure Metal Connector (2) to Back of Right Mirror with
Frame (C) and Back of Middle Mirror with Frame (B) with
NOTE: One hole of Metal Connector (2) is secured onto the
Back of Right Mirror with Frame (C) and the other hole is
secured onto the Back of Middle Mirror with Frame (B).
2. Secure Metal Connector (2) to Back of Left Mirror with
Frame (A) and Back of Middle Mirror with Frame (B) with
NOTE: One hole of Metal Connector (2) is secured onto the
Back of Left Mirror with Frame (A) and the other hole is
secured onto the Back of Middle Mirror with Frame (B).
Assembly is now complete.
A
Screw (7) using Phillips screwdriver (not provided).
Fully tighten screws.
Screw (11) using Phillips screwdriver (not provided).
Fully tighten screws.
Screw (11) using Phillips screwdriver (not provided).
Fully tighten screws.
B
C
11
2
11
11
A
B
B
C A
2
22
2