Big Lots Girls Unicorn Dress Up Table Set... User manual

Page 1 of 6
GIRLS UNICORN DRESS UP TABLE SET
810530880
BQ096-0692WH

Page 2 of 6
Read all instructions before starting
Clear a flat covered space to begin
Two adults are recommended for assembly
Note that hardware required is provided for every step
Pay attention to orientation
Letter of the part corresponds to a sticker on the product
Number of the hardware corresponds to its number on the package
Helpful hints provided along the way
MAINTENANCE:
WARNINGS:
GENERAL BEST PRACTICES FOR ASSEMBLY:
Regularlycheck hardware and tighten if necessary.
Usea dryclean cloth to dust or wipeup any spills.
Avoid exposure to water and fire.
SUGGEST 2ADULTSTO ASSEMBLE THIS PRODUCT IN AN OPEN AREA.
DO NOT USE POWER TOOLSTO ASSEMBLE

Page 3 of 6
NO QTY DESCRIPTION
A 1pc
B1pc
C1pc
D1pc
E1pc
F 2pcs
G 2pcs
H 1pc
2pcs
J 2pcs
1pc
I
Left Mirror with Frame
Middle Mirror with Frame
Side Drawer Panel
Back Drawer Panel
Right Mirror with Frame
Table Top
Wooden Slider
Front Table Leg
Rear Table Leg
Front Drawer Panel
K 2pcs
1pc Bottom Drawer Panel
1pc
M 2pcs
1pc
LWooden Handle
Stool Top
N 2pcs
4pcs Stool Leg
A
F
F
G
G
H
I
I
J
K
L
M
N
N
N
N
B
C
D
E

Page 4 of 6
1
NO QTY
PARTS DESCRIPTION
1
2
3
4
4pcs Metal Connector
1pc Stopper
4pcs Wooden Dowel
16pcs Bolt(6×35mm)
4x
85x 8 6x 8 12 x 1
5
6
7
16pcs Spring Washer
16pcs Flat Washer
4pcs Screw(4×30mm)
83pcs Screw(4×25mm)
98pcs Screw(3×20mm)
10
11
12
3pcs Screw(3×10mm)
8pcs Screw(3×8mm)
1pc Allen Wrench
N
N
N
N
M
Attach Stool Leg (N) to Stool Top (M) with Bolt (4), Spring Washer (5)
and Flat Washer (6) using Allen Wrench (12). Fully tighten bolts.
Note: The position of the Spring Washer (5) and Flat Washer (6) need
to be the same as the diagram below.
12
4
5
6
2
4x
8
5x 8 6x 8 12 x 1
D
G
G
F
F
Attach Front Table Leg (F) and Rear Table Leg (G) to Table Top (D)
with Bolt (4), Spring Washer (5) and Flat Washer (6) using Allen
Wrench (12) as show in the diagram. Fully tighten bolts.
Note: The position of the Spring Washer (5) and Flat Washer (6)
need to be the same as the diagram below.
12
4
5
6

Page 5 of 6
9
9
9
9
8x
2
9x8
4
3
I
I
I
J
J
K
H
H
H
8x 1
8
L
Attach Wooden Slider (E) to Bottom of Table Top (D)
with Screw (8) . Fully tighten screws.
1. Attach Wooden Handle (L) to Front Drawer Panel (H)
with Screw (8). Fully tighten screw.
2. Attach Back Drawer Panel (J) and Front Drawer Panel (H)
to Side Drawer Panel (I) with Screw (9). Fully tighten
screws.
3. Slide Bottom Drawer Panel (K) into the grooves of Front
Drawer Panel (H) and Back Drawer Panel (J) until it is fully
inserted into the groove of Side Drawer Panel (I).
4. Place the remaining Side Drawer Panel (I) into position so
Bottom Drawer Panel (K) is fully inserted into the groove.
Attach Side Drawer Panel (I) to Back Drawer Panel (J) and
Front Drawer Panel (H) with Screw (9). Fully tighten screws.
D
E
8
8
5
1
11
1
10
10
10
1x
110 x 3
K
G
G
F
F
J
J
EE
E
1. Slide the Stopper (1) over the Wooden Slider (E).
Note: The flat side of the Stopper should face the assembled Drawer.
2. Secure the Stopper to the Back Drawer Panel (J) with Screws (10).
Fully tighten screws.
Note: ensure the bottom of the assembled drawer is on top as shown before
attaching the the Stopper (1)

Page 6 of 6
9
7
3x
2
7x 2
6
B
B
B
B
C
C
C
G
G
F
F
2x411 x 8
3x 1 7x 1
D
D
D
7
7
7
7
3
3
3
3
A
A
11
11
11 11
2
2
2
2
1. Insert Wooden Dowel (3) into the holes of Middle Mirror
with Frame (B).
2. Align the Wooden Dowels (3) in Middle Mirror with
Frame (B) with the holes in Table Top (D) and lower
into place.
3. Secure Table Top (D) to Middle Mirror with Frame (B)
with Screw (7). Fully tighten screws.
1. Insert Wooden Dowel (3) into the holes of Right Mirror with
Frame (C).
2. Align the Wooden Dowels (3) in Right Mirror with Frame (C)
with the holes in Table Top (D) and lower into place.
3. Secure Table Top (D) to Right Mirror with Frame (C) with
Screw (7). Fully tighten screws.
83x 1 7x 1
1. Insert Wooden Dowel (3) into the holes of Left Mirror with
Frame (A).
2. Align the Wooden Dowels (3) in Left Mirror with Frame (A)
with the holes in Table Top (D) and lower into place.
3. Secure Table Top (D) to Left Mirror with Frame (A) with
Screw (7). Fully tighten screws.
1. Secure Metal Connector (2) to Back of Right Mirror with
Frame (C) and Back of Middle Mirror with Frame (B) with
Screws 11. Fully Tighten screws.
NOTE: One hole of Metal Connector (2) is secured onto the
Back of Right Mirror with Frame (C) and the other hole is
secured onto the Back of Middle Mirror with Frame (B).
2. Secure Metal Connector (2) to Back of Left Mirror with
Frame (A) and Back of Middle Mirror with Frame (B) with
Screws 11. Fully Tighten screws.
NOTE: One hole of Metal Connector (2) is secured onto the
Back of Left Mirror with Frame (A) and the other hole is
secured onto the Back of Middle Mirror with Frame (B).
Assembly is now complete.