Big Oshi STEPHANE CRB-414 User manual

Adult assembly required.
Small parts may present choking hazard prior to assembly.
Enclosed please find simple step-by-step instructions to help you
quickly assemble your products. Before you begin we recommend
that you following the steps below:
1. Please read the instructions thoroughly.
2. Identify all parts and hardware.
3. You will need the following tools:
Philips head screw driver
Flat head screw driver
Hammer
Do Not Use Power Drills or Drivers
To protect your parts during assembly please place them on a soft
surface.
To clean surface use only water on a damp cloth. Do not use
window cleaners or cleaning abrasives as it will scratch the surface
and could damage the protective coating.
1
s
Follow warnings on all products in a crib .
BABY TIME INT'L INC
250 PASSAIC ST., NEWARK, NJ 07104
4 IN 1 CONVERTIBLE STEPHANE CRIB
STYLE# CRB-414, CRB-415, CRB-416

.Read all instructions before assembling crib, keep instructions for future use.
.Upon completion of assembly be sure all screws, bolts and fastening devices have been
securely tightened. A frequent check should be made.
.Infants can suffocate in gaps between a mattress too small or too thick and product sides,
on soft bedding never add a mattress, pillow,comforter or padding.
.CAUTION: Any mattress used in this crib must be at least 27-1/4inches(690mm) by 51-5/8
inches(1310mm),with a thickness not exceeding 6 inches(150mm), the dimensions of the
.Failure to follow these warnings and the in structions could result in serious injury or death.
.Never use plastic shipping bag or other plastic film as mattress covers not sold and
intended for that purpose, they can cause suffocation .
.Strings can cause strangulation! Never place items with a string around a child’s neck,
.Never use this product if there are any loose or missing fasteners, loose joints,broken
parts, or torn mesh/fabric. check before assembly and periodically during use.
Contact BABY TIM E INT'L INC for replacement parts and instructional literature if needed.
.Never substitute parts, the product including side rails, must be fully erected prior to use.
.Discontinue use of the product when child is able to climb out or reaches the height of
.When child is able to pull to standing position,set mattress/base to lowest adjustment
positionand remove bumper pads, large toys ,and other objects that could serve as steps
for climbing out. A child can trap parts of the body or clothing on loose fasteners .
.Never use a water mattress with this product.
.If refinishing,use a non-toxic finish specified for children’s products.
.To reduce the risk of SIDS, pediatricians recommend healthy infants be placed on their
back to sleep, unless otherwise advised by your physician.
WARNING !
.Never place product near window where cords from blinds or drapes can strangle a child.
MADE IN CHINA
35in (900mm).
mattress shall be taken from seam to seam or edge to edge where appropriate.
such as hood strings or pacifier cords. Never suspend strings over product or attach
strings to toys.
.Infants can suffocate on soft bedding .
.Never add a pillow or comforter .
.Never place additional padding under an infant .
.To help prevent strangulation tighten all fasteners.
.A child can trap parts of the body or clothing on loose fasteners.
.Follow warnings on all products in a crib .
See head panel & mattress support of the product for warnings.
Replace teething rail if damaged,cracked or loose.
2

3
CONNECTION HARDWARE
a: M6*45 Allen head
bolt (7pcs)
b:Wood dowels (8pcs) c:Allen wrench (1pc)
d:M6*75
Allen head bolt (8pcs)
g:M6*55 Allen head bolt (8pcs)
e:Barrel nuts (16pcs) f: M6*15 Allen head bolt (4pcs)
PARTS ENCLOSED IN CARTON
A: Left head board (1 pc)
A1:Left back leg (1pc)
A2:Left board (1pc)
A3:Left front leg (1pc)
B: Right head board (1 pc)
B1:Right back leg (1pc)
B2:Right board (1pc)
B3:Right front leg (1pc)
C:Top rail (2 pc)
E: Back rail bottom (1 pc) F: Front rail bottom (1 pc) G: Mattress support (1 pc)
A1
A2
A3
B1
B2
B3
H:Rail (1pc)
J:The bottom bar (1pc)
H
J
Do not use electric hand drill

4
STEP 1
Attach left back leg (A1) and
left front leg (A3) to left board
(A2) using bolts (d) and barrel
nuts (e) .
Assemble right head board use
the same way .
STEP 2
d
d
d
d
e
e
e
e
A1
A2
A3
Attach The top rail (C) and The
back rail bottom (E) to The right
head board (B) and The left head
board (A) using wood dowels
(b),bolts (g),barrel nuts (e) and
allen wrench (c) .
e
e
e
e
g
g
g
g
a
a
c
C
E
A
B
b
b

5
STEP 3
STEP 4
Locate the mattress support (G)
with tabs .
Be sure the smooth side of the
mattress support (G) is faced upward .
Position the tabs of the mattress
support(G) to mount to the selected
position onto the legs .
Insert the bolts (f) , through the
tabs and into thread inserts ,
then tighten securely with allen
wrench (c) .
f
Attach The top rail (C) and The front
bottom rail (F) to The right head board
(B) and The left head board (A) using
wood dowels (b),bolts (g),barrel nuts (e)
and allen wrench (c) .
G
A
B
b
e
b
e
g
a
e
g
C
F
a

！
Failure to follow these warning and the assembly instructions could result in serious injury or
death from entrapment or strangulation. DO NOT place bed near windows where cords
from blinds or drapes may strangle a child. DO NOT place items with a string,cord,or ribbon
around a child’s neck,such as a hood, strings or pacifier cords. DO NOT suspend strings
over a toddler bed for any reason.
WARNING FOR TODDLER BED USE
The mattress intended for use on the bed shall be a full-size crib mattress having the
dimensions of 51-5/8” (1310 mm) in length and 27-1/4”(690mm) in width and thickness of
4” (100mm) or a greater thickness as specified by the manufacture. The minimum age of the
intended user shall not be less than 15 months and the maximum weight shall not be greater
than 50ibs(22.7kg).
6
Converting crib to a toddler bed
B
A
G
You have the option to convert crib to a toddler bed
2.Remove The front top rail (C1) and The front rail bottom
3.Install the mattress support (G) in its lowest position.
4.Assemble the Rail (H) and The bottom bar (J) to the left headboard(A) a
by Allen head bolts (a) , Allen head bolts (g) and nut (e).
1.Connect Rail (H) to The bottom bar (J) by Allen head bolts (a) .
H
H
J
J
a
a
e
e
g
g
g
g
Please note that the warning sticker is placed on the cribs to keep parents and
caregivers informed it is a requirement by law under CPSC And ASTM.
We do apologize for any inconvenience this may cause you.

7
Converting kit is sold separately
You have the option to convert
crib to a adult bed
1:Use the front rail as the
footboard of adult bed;
2:Use the back rail as the
headboard of adult bed;
3:Connect the front rail and the
back rail to the kits ( legs, long
rails,and hardware ) which are
not included and sold separately.
Converting crib to a adult bed
DO NOT RETURN TO STORE
CALL OR EMAIL FOR REPLACEMENT
TEL: [phone]
MAIL:[email protected]
Converting crib to a day bed
You have the option to convert crib to a day bed
1:Remove The front top rail (C1) and The
front rail bottom (F) .
2:Install the mattress support (G)
in its lowest position.
3.To assemble the bottom bar(J) to the
front legs as the image showed.
Model shown is example only.
Styles may vary .
J
g
g
g
ge
e