BIN WAREHOUSE 12-TOTE COMPACT User manual

12-TOTE COMPACT MODEL ASSEMBLY INSTRUCTIONS
TOOLS REQUIRED
1. Powered Screwdriver with
#2 Phillips-Head Tip
PARTS LIST
1. (8) Horizontal Crossbars
2. (4) Center Verticals
3. (2) Left & Right Rear Corner Verticals
4. (1) Left Front Corner Vertical
5. (1) Right Front Corner Vertical
6. (4) Wall Mount Flanges
7. (4) Wall Mount Extension Tubes
8. (12) Horizontal Sliderails
FASTENER LIST
1. (60) #06 x 1/2" Fastening Screws
2. (08) #08 x 3/4" Wall Mount
Extension Tube Fastening Screws
3. (12) #10 x 1-1/2" Wall Mount
Flange Screws
4. (12) Plastic Wall Anchors
TIP
Separate All Parts into Groups
(as shown) and Familiarize.
Read All Instructions Before
Beginning Assembly.
#1 #2
#3 #4
#4
#3
#5
#2
#1
#6
#7 #8
Solutions Murales PROSLAT inc.
225 Industriel blvd
Chateauguay (QC) J6J 4Z2
1 888 691-2944

IMPORTANT: Do not install any fasteners until instructed!
FRONT GRID ASSEMBLY
REAR GRID ASSEMBLY
SLIDERAIL ASSEMBLY
Step 1
Parts Needed:
4 of #1 2 of #2
2 of #3
Parts Needed:
4 of #1 2 of #2
1 of #4 1 of #5
4 Horizontal Crossbars (#1) inserted through
2 Center Verticals (#2)
Tip: When installing second Center Vertical, stand
assembly with Horizontal Crossbars placed on floor
and push down second Center Vertical to Alignment
Dimples.
1 Left Front Corner Vertical (#4) and 1 Right Front
Corner Vertical (#5) Placed on Horizontal
Crossbars
4 Horizontal Crossbars (#1) inserted through
2 Center Verticals (#2)
Tip: When installing second Center Vertical, stand
assembly with Horizontal Crossbars placed on floor
and push down second Center Vertical to Alignment
Dimples.
2 Left and Right Rear Corner Verticals (#3)
Placed on Horizontal Crossbars
12 Horizontal Sliderails (#8) inserted in Rear Grid
Tip: If necessary tap Horizontal Sliderails to be
sure Sliderails are fully inserted
Fastening Horizontal Sliderails (#8) in Rear Grid
using 12 - #06 x 1/2" Fastening Screws (#1)
Note: Start at top row and work down
Use only one fastener - Bottom Hole Only
All Horizontal Sliderails fastened to Rear Grid
Note: Fastener in Bottom Hole Only
Top
Step 2
#1
#1
#1
#1
#2 #2
Short side down
Holes down
Step 3 Top
Alignment Dimples Down
Holes down
Warning Labels
#4
#5
Step 1
#1 #2 #3
Step 2
#1
#2
#1
#1
#1
#2
Short side down
Holes up
Step 3
Alignment Dimples
#3 #3
Step 1
#8 #8 #8
#8 #8 #8
#8 #8 #8
#8 #8 #8
Short side down
Step 2 Top
Short side down
Fasten from Bottom Hole Only
Tilt Sliderails Forward
Step 3
Numbers in BOLD indicate item number from Parts/Fastener Lists.
#1
#2
#4
#5
Alignment Dimples
Alignment Dimples

IMPORTANT: Do not install any fasteners until instructed!
JOINING FRONT TO REAR GRID
Insert Bottom Sliderails (#8) into Front Grid
Assemble and fasten (making sure fully inserted)
using 3- #06 x 1/2" Fastening Screws (#1)
Note: Fasteners in Bottom Hole Only
Insert and fasten next 3 rows of Sliderail to Front
Grid using 9 - #06 x 1/2" Fastening Screws (#1)
Note: Fasteners in Bottom Hole Only
Turn unit upright and place firmly against wall where
unit is to be mounted.
FASTENING VERTICALS & WALLMOUNT TUBES
Fasten all Verticals to Horizontals. Make sure all
joints are pressed firmly together, tight and against
alignment dimples.
32 - #06 x 1/2" Fastening Screws (#1)
Note: 1 Fastener Per Joint, each grid, Front Side Only
Move unit away from wall and insert 4 Wallmount
Extension Tubes (#7) at 4 Locations.
Fasten With 8 - #08 x 3/4" Extension Tube
Fastening Screws (#2)
Note: 1 Fastener Per Joint Front Side Only
Mark Holes on Wall
Slide Wallmount Flange (#6) into Wallmount Tube (#7)
Place unit against wall where it is to be mounted and
mark Wall Flange holes.
Note: Do NOT fasten at this time. Make sure unit
remains in position at all 4 locations while marking
holes.
Move unit away from wall and remove Wall Flanges
from Tubes and mount Flanges to wall using 12 #10
x 1-1/2" Wall Mount Flange Screws (#3) and Plastic
Wall Anchors (#4) if needed.
Note: If mounted into Masonry or Drywall, drill
three 1/4" holes to accept Plastic Wall Anchors.
Slide unit back against wall while inserting all 4
Wallmount Extension Tubes (#7) into Wallmount
Flanges (#6) and fasten with 4 - #06 x 1/2" Fastening
Screws (#1).
Note: 1 Screw per Flange
FASTENING BIN WAREHOUSE TO WALL
Short Side Down
Unit MUST be attached to wall to prevent
from tipping over!
Alignment Dimple
#7
Wallmount Flange (#6)
Step 1 Step 2 Step 3
Step 1 Step 2 Step 3
Congratulations! We Hope You Enjoy Your Bin Warehouse!