Biomark HPR Lite User manual

+1 208.275.0011 www.biomark.com
Overview
For detailed instructions about the Biomark HPR
Lite Reader features and operation, please
download the complete HPR Lite Reader User
Manual from our website at:
https://www.biomark.com/hpr-lite-reader in the
Downloads & Help Section
Charging the Reader
The reader is charged by using the supplied Micro
USB cable plugged into either a computer USB
port or the provided AC power adapter. Note: The
HPR Lite reader needs to be fully charged before
first use.
Powering the Reader On
To power the reader on, press and hold the
center OK button. After ~1.5 seconds the main
screen will be displayed.
Powering the Reader Off
•To power down the reader, press and hold
the OK button. Continue to hold the OK
button until the reader shuts down.
•By default, the HPR Lite will shut down
automatically after 3 minutes of inactivity.
•Pressing any button will reset this time. This
function will become disabled if the reader is
connected via USB cable or extended to 1
hour of inactivity if the reader is connected
via Bluetooth® while in Slave mode.
QUICK START GUIDE
HPR LITE
READER

HPR LITE READER
QUICK START GUIDE 2
Reading PIT Tags
•To scan for PIT tags press and hold the READ button down. The reader will display
‘Reading...’ while it searches for a tag. Once the button is released the reader will stop
scanning.
•When a tag is detected the reader will stop scanning automatically and will display the
tag information on the screen.
•If no tag is detected, the reader will display the message ‘No tag detected’, and return to
the main screen.
Communications
The HPR Lite Reader is compatible with Biomark Device Manager Windows based software.
The software offers easy to use GUI for configuring the reader’s settings, updating its firmware
and downloading tag data from the reader. For more information about this product, please visit
www.biomark.com.
The HPR Lite reader is a USB device and does not require a specific baud rate to be selected
when setting up communications. If a baud rate is required by a program, any selection up to
115,200 will work.
Drivers for the reader should be installed automatically when it is connected to a PC via USB,
however if the drivers are not successfully installed automatically, they can be found by visiting
the HPR Lite page, in the Downloads & Help section at: https://www.biomark.com/hpr-lite-reader
By default, the Bluetooth module is discoverable and connectable (Slave mode or device).
Note: When Bluetooth authentication is disabled, default PIN code is 1234. This may be required
with old Bluetooth devices.
Reader Internal Clock
The reader’s internal clock is set at the factory to match the local time. This can be easily changed
using the reader’s LCD user interface or Device Manager software.
For detailed information on how to adjust the date and time settings to your time zone please refer
to the HPR Lite User Manual available for download on the Biomark website:
https://www.biomark.com/hpr-lite-reader in the Downloads & Help section
Warranty
•The HPR Lite reader is warranted against defects in materials and workmanship, under
normal use and service for one (1) year from the day of shipment.
•This warranty will not apply if adjustment, repair or parts replacement is required because
of accident, neglect, damage during transportation or causes other than ordinary use.
•Manufacturer’s sole responsibility under this warranty shall be at its option, to either repair
or replace any product which fails during the warranty period. In no event shall
Manufacturer be liable for any indirect or consequential damages or loss of profit.

HPR LITE READER
QUICK START GUIDE 3
USA-Federal Communications Commission (FCC)
This device complies with part 15 of FCC rules. Operation is subject to the following two
conditions: (1) This device may not cause interference, and (2) this device must accept any
interference, including interference that may cause undesired operation of the device.
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses, and can
radiate radio frequency energy. If not installed and used in accordance with the instructions, it
may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by tuning the equipment off
and on, the user is encouraged to try and correct the interference by one or more of the following
measures:
•Reorient or relocate the receiving antenna.
•Increase the distance between the equipment and the receiver.
•Connect the equipment to outlet on a circuit different from that to which the receiver
is connected.
•Consult the dealer or an experienced radio/TV technician for help.
Notice to consumers: Any changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate the equipment.
Canada - Industry Canada (IC)
This device complies with RSS 210 of Industry Canada. Operation is subject to the following two
conditions: (1) This device may not cause interference, and (2) this device must accept any
interference, including interference that may cause undesired operation of the device.
L’utilisation de ce dispositif est autorisée seulement aux conditions suivantes :
(1) Il ne doit pas produire d'interférence et (2) l'utilisateur du dispositif doit être prêt à accepter
toute interférence radioélectrique reçu, même si celle-ci est susceptible de compromettre le
fonctionnement du dispositif.
Avis aux consommateurs: Toutes modifications non expressément approuvées par la partie
responsable de la conformité peuvent annuler le droit de l'utilisateur à utiliser cet équipement.
Miscellaneous Information
Snapshots are according to the latest version at the moment this document was printed.
Changes may occur without notice.
Trademarks
Bluetooth® is a registered trademark of Bluetooth SIG, Inc.
Windows is a trademark or registered trademark of Microsoft Corporation in the United States
and/or other countries.
All other trademarks are trademarks of their respective owners.

HPR LITE READER
QUICK START GUIDE 4
Regulatory Compliance
ISO 11784 & 11785
This device complies with the standards set forward by the International Standardization
Organization. Specifically, with standards:
11784: Radio frequency identification of animals -- Code Structure
11785: Radio frequency identification of animals -- Technical Concept.
FCC NQY-30019
IC 4248A-30019
CE Declaration of ConformityBiomark, Inc. hereby declares that the radio equipment type HPR
Lite complies with the directive 2014/53/EU.
The full text of the EU declaration of conformity is available at the following internet address:
https://www.biomark.com/hpr-lite-reader#product.info.specifications
705 S 8TH ST, BOISE, ID USA | +1 208.275.0011 | [email protected] | www.biomark.com