Avision DT-0602S User manual

A3 Bookedge Scanner
User’s Manual
Regulatory model: DT-0602S

i
i
Trademarks
Microsoft is a U.S. registered trademark of Microsoft
Corporation.
Windows and MS-DOS are trademarks of Microsoft Corporation.
IBM, PC, AT, XT are registered trademarks of International
Business Machines Corp.
ENERGY STAR®is a U.S. registered mark.
Other brands and product names herein are trademarks or
registered trademarks of their respective holders.
Copyright
All rights reserved. No part of this publication may be
reproduced, transmitted, transcribed, stored in a retrieval
system, or translated into any language or computer
language, in any form or by any means, electronic,
mechanical, magnetic, optical, chemical, manual, or
otherwise, without the prior written permission of Avision
Inc.
Material scanned by this product may be protected by
governmental laws and other regulations, such as copyright
laws, the customer is solely responsible for complying with
all such laws and regulations.
Warranty
The information contained in this document is subject to
change without notice.
Avision makes no warranty of any kind with regard to
this material, including, but not limited to, the implied
warranties of fitness for a particular purpose.
Avision shall not be liable for errors contained herein or
for incidental or consequential damages in connection
with the furnishing, performance, or use of this material.

ii
i
FCC Radio Frequency Interference Statement
This product has been tested and found to comply with
the limits for a class B digital device, pursuant to Part
15 of the FCC rules. Operation is subject to the
following two conditions: (1) this device may not cause
harmful interference, and (2) this device must accept
any interference received, including interference that
may cause undesired operation. The FCC Class B
limits are designed to provide reasonable protection
against harmful interference in a residential installation.
This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However, there
is no guarantee that interference will not occur in a
particular installation. If this equipment does cause
harmful interference to radio or television reception,
which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and
receiver.
Connect the equipment into an outlet on a circuit
different from that to which the receiver is
connected.
Consult your point of purchase or service
representative for additional suggestions.
CE Warning
This product satisfies the Class B limits of EN55022,
EN55024 and safety requirements of EN 60950.

i
v
Disposal of Waste Equipment by Users in Private
Union
This symbol on the product or on its packaging indicates
that the product can not be disposed of with your other
household waste. Instead it should be sent to appropriate
facilities for recovery and recycling in an effort to protect
human health and the environment. Fore more information
about where you can drop off your waste equipment for
recycling, please contact your local city office, your
household waste disposal service or the shop where you
purchased the product.
As an ENERGY STAR® Partner, Avision Inc.
has determined that this product meets the ENERGY
STAR guidelines for energy efficiency.

v
System Requirements
¾IBM compatible PC 586, Pentium or higher
¾Microsoft Windows 98SE/Me/2000/XP
¾USB port 2.0 (compatible with USB 1.1)
¾At least 100 MB of free hard disk space
¾At least 128 MB of system memory
¾A CD-ROM drive

v
i
Table of Contents
1. Introduction......................................................1-1
2. Scanner Installation........................................2-1
2.1 PRECAUTIONS............................................................. 2-1
2.2 UNLOCKING YOUR SCANNER ....................................... 2-2
2.3 INSTALLING THE SCANNER DRIVER AND CABLES ........ 2-3
2.3.1 Connecting to Power............................... 2-3
2.3.2 Installing the Scanner driver................ 2-3
2.3.3 Connecting to Computer........................ 2-4
3. completing your first scan.............................3-1
3.1 PLACING YOUR ORIGINAL............................................ 3-1
3.2 VERIFYING YOUR SCANNER INSTALLATION ................. 3-2
4. Using the Scanner Properties Box................4-1
4.1 BUTTONS ON THE SCANNER PROPERTIES DIALOG BOX4-2
4.2 THE IMAGE TAB.......................................................... 4-4
4.2.1 The Image Selection Box....................... 4-5
4.2.2 Other Image Options.............................. 4-8
4.2.3 Scanning color images......................... 4-13
4.2.4 Scanning grayscale images................. 4-14
4.2.5 Scanning B&W images......................... 4-14
4.2.6 Editing Profiles....................................... 4-15
4.3 THE COMPRESSION TAB ........................................... 4-18
4.4 THE COLOR DROPOUT TAB....................................... 4-20
4.4.1 Color Dropout Selection....................... 4-20
4.4.2 Other Color Dropout Options.............. 4-21
4.5 THE PAPER TAB........................................................ 4-23
4.5.1 Cropping.................................................. 4-24
4.5.2 Other Paper Selection .......................... 4-27
4.5.3 Relative to Document........................... 4-31
4.6 THE OPTIONS TAB.................................................... 4-34
4.7 THE SETTING TAB.................................................... 4-39
4.8 THE INFORMATION TAB............................................ 4-42

vi
i
5. ISIS Interface operation ................................5-1
6. Using the Button..............................................6-1
6.1 INSTALLING BUTTON MANAGER.................................. 6-2
6.2 CHECKING THE BUTTON CONFIGURATIONS BEFORE
SCANNING.................................................................. 6-3
6.3 SCANNING FROM ONE TOUCH OF THE BUTTONS......... 6-5
6.4 PERFORMING CONTINUOUS SCAN FROM THE FLATBED 6-6
7. care and Maintenance.....................................7-1
7.1 CLEANING THE GLASS ................................................ 7-1
8. Troubleshooting...............................................8-1
8.1 FREQUENTLY ASKED QUESTIONS ................................ 8-1
8.2 TECHNICAL SERVICE .................................................. 8-3
9. Specifications ...................................................9-1

1-1
1. INTRODUCTION
Congratulations on your purchase of the Avision’s A3-sized
bookedge scanner. Avision is one of the leading companies to
make high quality color image scanner.
To ensure the optimum performance of the scanner, please
take a few minutes to read through this manual before you
install and operate the new scanner. The manual contains
valuable information on how to unpack, install, operate,
and maintain the scanner properly.
Figure 1-1 in below shows how the scanner is packed.
Please check if all items are included. If there is any item
missing or damaged, please contact your nearest dealer
immediately for replacement.

1-2
1. Scanner main unit
2. Power adapter
3. Power cord
4. USB cable
5. User’s manual/CD
Figure 1-1 Scanner Packaging
Note: When you unpack the scanner, retain the
packing material and shipping box in case you may
transport the scanner in the future.
Note:
1. Only use the AC adapter (HEG42-240200-7L by HiTron)
included in the machine. Using other AC adapters may
damage the machine and void the warranty.
2. Please unpack the packing carefully, and check the
contents against the checklist. If any items are missing
or damaged, please contact your dealer immediately.
1
2
3
4
5

2-1
2. SCANNER
INSTALLATION
2.1 PRECAUTIONS
•Keep the scanner out of direct sunlight. Direct
exposure to the sun or excessive heat may cause
damage to the unit.
•Do not install the scanner in a humid or dusty place.
•Place the scanner securely on an even, flat surface.
Tilted or uneven surfaces may cause mechanical
problems.
•Keep the shipping box and the material in case you may
need to ship the scanner again.

2-2
2.2 UNLOCKING YOUR SCANNER
To protect the scanning unit from damage during
transportation, a lock switch is designed at the back of the
scanner to keep the scanning unit from moving. To unlock
the scanner, move the lock switch up as shown in Fig. 2-1.
Figure 2-1 Unlocking the Scanner
Figure 2-2 Home position
Note: If the scanning unit is not located at the front of the
scanner before transporting the scanner, be sure to do the
follows:
1. Turn on the scanner.
2. The scanning unit should move to the front of the
scanner.
3. Press the lock switch down to the “Lock position”.
4. The scanner is now ready to transport.
Unlocked
Locked
Scanning unit at this
position before
locking the scanner

2-3
2.3 INSTALLING THE SCANNER DRIVER AND CABLES
Note:
1. The Windows system CD may be required when
installing on some PC’s.
2. To ensure your computer can identify the USB
scanner, please install scanner driver first before
connecting the scanner to your computer.
2.3.1 CONNECTING TO POWER
Make sure the power of scanner is off.
Plug the small end of the power adaptor into the power jack
of your scanner. Insert the other end to an appropriate
power outlet.
2.3.2 INSTALLING THE SCANNER DRIVER
1. Place the supplied CD-ROM onto your CD-ROM drive.
2. The software installation graphic appears. If not, run
“setup.exe”.
Power Cable

2-4
3. Choose Install Button Manager first and then install
Scanner Driver and follow the on-screen instruction to
complete the installation.
2.3.3 CONNECTING TO COMPUTER
1. Connect the square end of the USB cable to the USB port
of your scanner. Connect the rectangle end to the USB
port of your computer.
USB cable

2-
5
2. The computer should detect a new USB device and
prompt a “New Hardware Found” message.
(Windows 9X/Windows ME)
3. In Windows 9X, Windows 2000 or Windows ME, confirm
that the “Search for a better driver.” is selected and
click the “Next” button.
In Windows XP, click the Next button to continue.
When the XP certification screen appears, click
Continue Anyway to complete the installation.
4. When the Finish dialog is prompted, click the Finish
button.
5. Click “View Manual” to view or print the detailed user
manual for the scanner and bundled applications
respectively.
Note:
To uninstall the scanner driver in Windows XP/2000, be sure to
keep your scanner connecting to your computer.

3-1
3. COMPLETING YOUR
FIRST SCAN
3.1 PLACING YOUR ORIGINAL
Open the document cover then place your original face
down on the document glass as shown in Fig. 3-1.
Make sure the top of your original near the document
alignment mark.
1. Document cover
2. Document alignment mark
3. Your original
4. Document glass
Figure 3-1 Placing the original
1
3
4
2

3-2
3.2 VERIFYING YOUR SCANNER INSTALLATION
To verify if your scanner installation is correct, Avision
provides you a useful test program called Avision Capture
Tool. With this tool, you can perform simple scans and
view the captured images. In addition, it helps you
complete your scan at a rated speed.
The following procedure describes how to verify your
scanner installation. If the installation is not correct, please
review the preceding section to check if the cable
connection and scanner driver have been successfully
installed.
Before you begin, be sure the scanner is on.
1. Select Start>Programs>Avision AVxxx Scanner>Avision
Capture Tool.
The Select Scanner Model dialog box will be displayed.
2. Select your driver type and scanner model and click OK.
The following Avision Capture Tool dialog box will be
displayed.

3-3
3. Choose your desired file format from the File Format
drop down list box. (Default is BMP, other choice
includes TIFF, GIF, and JPEG.)
4. Type your desired folder name and file name in the File
Path box. (Default is C:\My Scan\Image.)
Note: If you do not wish to save the scanned image,
deselect the Save button since default is Save Enable.
In this case, the thumbnail view will be disabled. And
therefore, after viewing all the scanned images, only the
last one will remain on the screen.
5. Click the Setup button ( ) or choose Setup from
the File menu to prompt the Scanner Properties dialog
box.
Setup
Actual
Size
Fit
Page
Scan File Format Save File Path

3-4
6. From the Image Selection Box, choose your desired
image type for your scanned image. (Default is Front
B&W) If you have a duplex scanner, choose Front and
Rear to scan both sides of your document.
7. Click OK to quit the Scanner Properties dialog box. (To
learn more details about the Scanner Properties dialog
box, please see the subsequent chapter, Using the
Scanner Properties Dialog Box.)
8. Place your document face down on the document glass
or face up in the auto document feeder.
9. In the Scan Validation dialog box, click the Scan button
() or choose Scan from the File menu.
10. The document will be scanned and displayed in the
Scan Validation screen. After the scanned images have
been displayed, your scanner installation verification is
completed.
Image
Selection
Box

3-5
11. You can view the scanned image in Fit Page ( ) or
Actual Size (100%) button ( ) from the Viewing
toolbars at the right side.
12. Click the Close box or Quit from the File menu to exit
the Scan Validation Tool.
Fit Page View
Status Bar
Thumbnail View

4-1
4. USING THE SCANNER
PROPERTIES BOX
The Scanner Properties dialog box allows you to configure
the scanner’s settings. It consists of several tabbed
windows each of which will be described in this chapter.
The Scanner Properties dialog box