Black & Decker BDCDD12USB User manual

3 24
1
5
7
6
3
8
BDCDD12USB 简体中文
简体中文
ENGLISH 2
简体中文 8

2
2
4 4a
6
7
B
D
68
A
3
C
Intended use
Your BLACK+DECKER BDCDD12USB - Drill, has been
designed for screwdriving applications and for drilling in wood,
metal and plastics. This tool is intended for consumer use
only.
Safety instructions
General power tool safety warnings
@Warning! Read all safety warnings and all
instructions. Failure to follow the warnings
and instructions listed below may result in
Save all warnings and instructions for future reference.
The term "power tool" in all of the warnings listed below refers
to your mains operated (corded) power tool or battery oper-
ated (cordless) power tool.
1. Work area safety
a. Keep work area clean and well lit. Cluttered or dark
areas invite accidents.
b. Do not operate power tools in explosive atmospheres,
or dust. Power tools create sparks which may ignite the
dust or fumes.
c. Keep children and bystanders away while operating a
power tool. Distractions can cause you to lose control.
3
ENGLISH
(Original instructions)
g. If devices are provided for the connection of dust
extraction and collection facilities, ensure these are
connected and properly used. Use of dust collection
can reduce dust-related hazards.
4. Power tool use and care
a. Do not force the power tool. Use the correct power
tool for your application. The correct power tool will do
the job better and safer at the rate for which it was
designed.
b. Do not use the power tool if the switch does not turn it
on and off. Any power tool that cannot be controlled with
the switch is dangerous and must be repaired.
c. Disconnect the plug from the power source and/or the
battery pack from the power tool before making any
adjustments, changing accessories, or storing power
tools. Such preventive safety measures reduce the risk of
starting the power tool accidentally.
d. Store idle power tools out of the reach of children and
do not allow persons unfamiliar with the power tool or
these instructions to operate the power tool. Power
tools are dangerous in the hands of untrained users.
e. Maintain power tools. Check for misalignment or
binding of moving parts, breakage of parts and any
other condition that may affect the power tools
operation. If damaged, have the power tool repaired
before use. Many accidents are caused by poorly
maintained power tools.
f. Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges are less
likely to bind and are easier to control.
g. Use the power tool, accessories and tool bits etc. in
accordance with these instructions, taking into
account the working conditions and the work to be
performed. Use of the power tool for operations different
from those intended could result in a hazardous situation.
5. Battery tool use and care
a.
manufacturer. A charger that is suitable for one type of
another battery pack.
b. designated
battery packs. Use of any other battery packs may create
c. When battery pack is not in use, keep it away from
other metal objects, like paper clips, coins, keys,
nails, screws, or other small metal objects, that can
make a connection from one terminal to another.
Shorting the battery terminals together may cause burns
2. Electrical safety
a. Power tool plugs must match the outlet. Never modify
the plug in any way. Do not use any adapter plugs
with earthed (grounded) power tools.
and matching outlets will reduce risk of electric shock.
b. Avoid body contact with earthed or grounded
surfaces such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric shock
if your body is earthed or grounded.
c. Do not expose power tools to rain or wet conditions.
Water entering a power tool will increase the risk of
electric shock.
d. Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool. Keep
cord away from heat, oil, sharp edges or moving
parts. Damaged or entangled cords increase the risk of
electric shock.
e. When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of a cord
suitable for outdoor use reduces the risk of electric shock.
f. If operating a power tool in a damp location is
unavoidable, use a residual current device (RCD)
protected supply. Use of an RCD reduces the risk of
electric shock.
3. Personal safety
a. Stay alert, watch what you are doing and use common
sense when operating a power tool. Do not use a
of drugs, alcohol or medication. A moment of inattention
while operating power tools may result in serious personal
injury.
b. Use personal protective equipment. Always wear eye
protection. Protective equipment such as dust mask,
non-skid safety shoes, hard hat, or hearing protection
used for appropriate conditions will reduce personal
injuries.
c. Prevent unintentional starting. Ensure the switch is in
the off-position before connecting to power source
and/or battery pack, picking up or carrying the tool.
energising power tools that have the switch on invites
accidents.
d. Remove any adjusting key or wrench before turning
the power tool on. A wrench or a key left attached to a
rotating part of the power tool may result in personal injury.
e. Do not overreach. Keep proper footing and balance at
all times. This enables better control of the power tool in
unexpected situations.
f. Dress properly. Do not wear loose clothing or
jewellery. Keep your hair, clothing and gloves away
from moving parts. Loose clothes, jewellery or long hair
can be caught in moving parts.

3
ENGLISH
2
4 4a
6
7
B
D
68
A
3
C
Intended use
Your BLACK+DECKER BDCDD12USB - Drill, has been
designed for screwdriving applications and for drilling in wood,
metal and plastics. This tool is intended for consumer use
only.
Safety instructions
General power tool safety warnings
@Warning! Read all safety warnings and all
instructions. Failure to follow the warnings
and instructions listed below may result in
Save all warnings and instructions for future reference.
The term "power tool" in all of the warnings listed below refers
to your mains operated (corded) power tool or battery oper-
ated (cordless) power tool.
1. Work area safety
a. Keep work area clean and well lit. Cluttered or dark
areas invite accidents.
b. Do not operate power tools in explosive atmospheres,
or dust. Power tools create sparks which may ignite the
dust or fumes.
c. Keep children and bystanders away while operating a
power tool. Distractions can cause you to lose control.
3
ENGLISH
(Original instructions)
g. If devices are provided for the connection of dust
extraction and collection facilities, ensure these are
connected and properly used. Use of dust collection
can reduce dust-related hazards.
4. Power tool use and care
a. Do not force the power tool. Use the correct power
tool for your application. The correct power tool will do
the job better and safer at the rate for which it was
designed.
b. Do not use the power tool if the switch does not turn it
on and off. Any power tool that cannot be controlled with
the switch is dangerous and must be repaired.
c. Disconnect the plug from the power source and/or the
battery pack from the power tool before making any
adjustments, changing accessories, or storing power
tools. Such preventive safety measures reduce the risk of
starting the power tool accidentally.
d. Store idle power tools out of the reach of children and
do not allow persons unfamiliar with the power tool or
these instructions to operate the power tool. Power
tools are dangerous in the hands of untrained users.
e. Maintain power tools. Check for misalignment or
binding of moving parts, breakage of parts and any
other condition that may affect the power tools
operation. If damaged, have the power tool repaired
before use. Many accidents are caused by poorly
maintained power tools.
f. Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges are less
likely to bind and are easier to control.
g. Use the power tool, accessories and tool bits etc. in
accordance with these instructions, taking into
account the working conditions and the work to be
performed. Use of the power tool for operations different
from those intended could result in a hazardous situation.
5. Battery tool use and care
a.
manufacturer. A charger that is suitable for one type of
another battery pack.
b. designated
battery packs. Use of any other battery packs may create
c. When battery pack is not in use, keep it away from
other metal objects, like paper clips, coins, keys,
nails, screws, or other small metal objects, that can
make a connection from one terminal to another.
Shorting the battery terminals together may cause burns
2. Electrical safety
a. Power tool plugs must match the outlet. Never modify
the plug in any way. Do not use any adapter plugs
with earthed (grounded) power tools.
and matching outlets will reduce risk of electric shock.
b. Avoid body contact with earthed or grounded
surfaces such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric shock
if your body is earthed or grounded.
c. Do not expose power tools to rain or wet conditions.
Water entering a power tool will increase the risk of
electric shock.
d. Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool. Keep
cord away from heat, oil, sharp edges or moving
parts. Damaged or entangled cords increase the risk of
electric shock.
e. When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of a cord
suitable for outdoor use reduces the risk of electric shock.
f. If operating a power tool in a damp location is
unavoidable, use a residual current device (RCD)
protected supply. Use of an RCD reduces the risk of
electric shock.
3. Personal safety
a. Stay alert, watch what you are doing and use common
sense when operating a power tool. Do not use a
of drugs, alcohol or medication. A moment of inattention
while operating power tools may result in serious personal
injury.
b. Use personal protective equipment. Always wear eye
protection. Protective equipment such as dust mask,
non-skid safety shoes, hard hat, or hearing protection
used for appropriate conditions will reduce personal
injuries.
c. Prevent unintentional starting. Ensure the switch is in
the off-position before connecting to power source
and/or battery pack, picking up or carrying the tool.
energising power tools that have the switch on invites
accidents.
d. Remove any adjusting key or wrench before turning
the power tool on. A wrench or a key left attached to a
rotating part of the power tool may result in personal injury.
e. Do not overreach. Keep proper footing and balance at
all times. This enables better control of the power tool in
unexpected situations.
f. Dress properly. Do not wear loose clothing or
jewellery. Keep your hair, clothing and gloves away
from moving parts. Loose clothes, jewellery or long hair
can be caught in moving parts.

4
ENGLISH
4
ENGLISH
(Original instructions)
d. Under abusive conditions, liquid may be ejected from
the battery; avoid contact. If contact accidentally
additionally seek medical help. Liquid ejected from the
battery may cause irritation or burns.
6. Service
a.
person using only identical replacement parts. This will
ensure that the safety of the power tool is maintained.
Additional power tool safety warnings
@Warning! Additional safety warnings for
drills
uUse auxiliary handles supplied with the tool. Loss of
control can cause personal injury.
uHold power tool by insulated gripping surfaces when
performing an operation where the cutting accessory
may contact hidden wiring. Cutting accessory contacting
a "live" wire may make exposed metal parts of the power
tool "live" and could give the operator an electric shock.
uUse clamps or another practical way to secure and
support the workpiece to a stable platform. Holding the
work by hand or against your body leaves it unstable and
may lead to loss of control.
u
location of wiring and pipes.
uAvoid touching the tip of a drill bit just after drilling, as it
may be hot.
uThe intended use is described in this instruction manual.
The use of any accessory or attachment or performance
of any operation with this tool other than those recom-
mended in this instruction manual may present a risk of
personal injury and/or damage to property.
Safety of others
uThis tool is not intended for use by persons (including
children) with reduced physical, sensory or mental capa-
bilities, or lack of experience and knowledge, unless they
have been given supervision or instruction concerning use
of the tool by a person responsible for their safety.
uChildren should be supervised to ensure that they do not
play with the appliance.
Residual risks
Additional residual risks may arise when using the tool which
may not be included in the enclosed safety warnings.
These risks can arise from misuse, prolonged use etc.
Even with the application of the relevant safety regulations
and the implementation of safety devices, certain residual
risks can not be avoided. These include:
uInjuries caused by touching any rotating/moving parts.
uInjuries caused when changing any parts, blades or ac-
cessories.
uInjuries caused by prolonged use of a tool. When using
any tool for prolonged periods ensure you take regular
breaks.
uImpairment of hearing.
uHealth hazards caused by breathing dust developed when
using your tool (example:- working with wood, especially
oak, beech and MDF.)
Labels on tool
The following symbols are shown on the tool along with the
date code:
:Warning! To reduce the risk of injury, the user
must read the instruction manual.
Additional safety instructions for batteries
Batteries
uNever attempt to open for any reason.
uDo not expose the battery to water.
uDo not store in locations where the temperature may
exceed 40 °C.
uCharge only at ambient temperatures between 10 °C and
40 °C.
uCharge only using the charger provided with the tool.
uWhen disposing of batteries, follow the instructions given
in the section "Protecting the environment".
pDo not attempt to charge damaged batteries.
$The tool is intend of indoor use only.
Features
This tool includes some or all of the following features.
1. Variable speed switch
2. Forward/reverse slider
3. Torque adjustment collar
4. Keyless chuck
5. LED work light
6. Battery
7. Battery release button
Assembly
Use
Warning! Let the tool work at its own pace. Do not overload.
5
ENGLISH
(Original instructions)
-
done before. The battery may become warm while charging;
this is normal and does not indicate a problem.
Warning! Do not charge the battery at ambient temperatures
below 10 °C or above 40 °C. Recommended charging tem-
perature: approx. 24 °C.
Note: The charger will not charge a battery if the cell
temperature is below approximately 10 °C or above 40 °C.
The battery should be left in the charger and the charger
will begin to charge automatically when the cell tempera-
ture warms up or cools down.
uTo charge the battery, insert the USB charger (8) into the
Battery.
uPlug the charger into a suitable power source and switch
on.
uCharge discharged batteries within 1 week. Battery life will
be greatly diminished if stored in a discharged state.
Warning!
then disconnect the charger cord from the tool.
Fitting and removing the battery
u
Slide the battery into the receptacle and push up until the
battery snaps into place.
uTo remove the battery, push the release button (7) while at
the same time pulling the battery out of the receptacle.
Operating Instructions
the operating mode and to set the torque for tightening
screws. Large screws and hard workpiece materials require
a higher torque setting than small screws and soft workpiece
materials.
uFor drilling in wood, metal and plastics, set the collar to
the drilling position symbol
uFor screwdriving, set the collar to the desired setting. If
you do not yet know the appropriate setting, proceed as
follows:
uSet the collar to the lowest torque setting.
uT
uIf the clutch ratchets before the desired result is achieved,
increase the collar setting and continue tightening the
screw. Repeat until you reach the correct setting. Use this
setting for the remaining screws.
Warning! Make certain the lock-off button is engaged to
prevent switch actuation before installing or removing acces-
sories.
To insert a drill bit or other accessory:
uGrasp the rear half of the chuck (4a) with one hand and
use your other hand to rotate the front half (4) in the
counterclockwise direction, as viewed from the chuck end.
uInsert the bit or other accessory fully into the chuck, and
tighten securely by holding the rear half of the chuck and
rotating the front portion in the clockwise direction as
viewed from the chuck end.
Warning! Do not attempt to tighten drill bits (or any other ac-
cessory) by gripping the front part of the chuck and turning the
tool on. Damage to the chuck and personal injury may occur
when changing accessories.
Drilling/screwdriving
uSelect forward or reverse rotation using the forward/re-
verse slider (2).
uTo switch the tool on, press the switch (1). The tool speed
depends on how far you press the switch.
uTo switch the tool off, release the switch.
Hints for optimum use
Drilling
uUse sharp drill bits only.
uSupport and secure work properly, as instructed in the
Safety Instructions.
uUse appropriate and required safety equipment, as
instructed in the Safety Instructions.
uSecure and maintain work area, as instructed in the
Safety Instructions.
uRun the drill very slowly, using light pressure, until
the hole is started enough to keep the drill bit from slipping
out of it.
uApply pressure in a straight line with the bit. Use enough
pressure to keep the bit biting but not so much as to stall
u
action.
uDO NOT CLICK THE TRIGGER OF A STALLED DRILL
OFF AND ON IN AN ATTEMPT TO START IT. DAMAGE
TO THE DRILL CAN RESULT.
uMinimize stalling on breakthrough by reducing pressure
and slowly drilling through the last part of the hole.
uKeep the motor running while pulling the bit out of a drilled
hole. This will help reduce jamming.
uMake sure switch turns drill on and off.

5
ENGLISH
4
ENGLISH
(Original instructions)
d. Under abusive conditions, liquid may be ejected from
the battery; avoid contact. If contact accidentally
additionally seek medical help. Liquid ejected from the
battery may cause irritation or burns.
6. Service
a.
person using only identical replacement parts. This will
ensure that the safety of the power tool is maintained.
Additional power tool safety warnings
@Warning! Additional safety warnings for
drills
uUse auxiliary handles supplied with the tool. Loss of
control can cause personal injury.
uHold power tool by insulated gripping surfaces when
performing an operation where the cutting accessory
may contact hidden wiring. Cutting accessory contacting
a "live" wire may make exposed metal parts of the power
tool "live" and could give the operator an electric shock.
uUse clamps or another practical way to secure and
support the workpiece to a stable platform. Holding the
work by hand or against your body leaves it unstable and
may lead to loss of control.
u
location of wiring and pipes.
uAvoid touching the tip of a drill bit just after drilling, as it
may be hot.
uThe intended use is described in this instruction manual.
The use of any accessory or attachment or performance
of any operation with this tool other than those recom-
mended in this instruction manual may present a risk of
personal injury and/or damage to property.
Safety of others
uThis tool is not intended for use by persons (including
children) with reduced physical, sensory or mental capa-
bilities, or lack of experience and knowledge, unless they
have been given supervision or instruction concerning use
of the tool by a person responsible for their safety.
uChildren should be supervised to ensure that they do not
play with the appliance.
Residual risks
Additional residual risks may arise when using the tool which
may not be included in the enclosed safety warnings.
These risks can arise from misuse, prolonged use etc.
Even with the application of the relevant safety regulations
and the implementation of safety devices, certain residual
risks can not be avoided. These include:
uInjuries caused by touching any rotating/moving parts.
uInjuries caused when changing any parts, blades or ac-
cessories.
uInjuries caused by prolonged use of a tool. When using
any tool for prolonged periods ensure you take regular
breaks.
uImpairment of hearing.
uHealth hazards caused by breathing dust developed when
using your tool (example:- working with wood, especially
oak, beech and MDF.)
Labels on tool
The following symbols are shown on the tool along with the
date code:
:Warning! To reduce the risk of injury, the user
must read the instruction manual.
Additional safety instructions for batteries
Batteries
uNever attempt to open for any reason.
uDo not expose the battery to water.
uDo not store in locations where the temperature may
exceed 40 °C.
uCharge only at ambient temperatures between 10 °C and
40 °C.
uCharge only using the charger provided with the tool.
uWhen disposing of batteries, follow the instructions given
in the section "Protecting the environment".
pDo not attempt to charge damaged batteries.
$The tool is intend of indoor use only.
Features
This tool includes some or all of the following features.
1. Variable speed switch
2. Forward/reverse slider
3. Torque adjustment collar
4. Keyless chuck
5. LED work light
6. Battery
7. Battery release button
Assembly
Use
Warning! Let the tool work at its own pace. Do not overload.
5
ENGLISH
(Original instructions)
-
done before. The battery may become warm while charging;
this is normal and does not indicate a problem.
Warning! Do not charge the battery at ambient temperatures
below 10 °C or above 40 °C. Recommended charging tem-
perature: approx. 24 °C.
Note: The charger will not charge a battery if the cell
temperature is below approximately 10 °C or above 40 °C.
The battery should be left in the charger and the charger
will begin to charge automatically when the cell tempera-
ture warms up or cools down.
uTo charge the battery, insert the USB charger (8) into the
Battery.
uPlug the charger into a suitable power source and switch
on.
uCharge discharged batteries within 1 week. Battery life will
be greatly diminished if stored in a discharged state.
Warning!
then disconnect the charger cord from the tool.
Fitting and removing the battery
u
Slide the battery into the receptacle and push up until the
battery snaps into place.
uTo remove the battery, push the release button (7) while at
the same time pulling the battery out of the receptacle.
Operating Instructions
the operating mode and to set the torque for tightening
screws. Large screws and hard workpiece materials require
a higher torque setting than small screws and soft workpiece
materials.
uFor drilling in wood, metal and plastics, set the collar to
the drilling position symbol
uFor screwdriving, set the collar to the desired setting. If
you do not yet know the appropriate setting, proceed as
follows:
uSet the collar to the lowest torque setting.
uT
uIf the clutch ratchets before the desired result is achieved,
increase the collar setting and continue tightening the
screw. Repeat until you reach the correct setting. Use this
setting for the remaining screws.
Warning! Make certain the lock-off button is engaged to
prevent switch actuation before installing or removing acces-
sories.
To insert a drill bit or other accessory:
uGrasp the rear half of the chuck (4a) with one hand and
use your other hand to rotate the front half (4) in the
counterclockwise direction, as viewed from the chuck end.
uInsert the bit or other accessory fully into the chuck, and
tighten securely by holding the rear half of the chuck and
rotating the front portion in the clockwise direction as
viewed from the chuck end.
Warning! Do not attempt to tighten drill bits (or any other ac-
cessory) by gripping the front part of the chuck and turning the
tool on. Damage to the chuck and personal injury may occur
when changing accessories.
Drilling/screwdriving
uSelect forward or reverse rotation using the forward/re-
verse slider (2).
uTo switch the tool on, press the switch (1). The tool speed
depends on how far you press the switch.
uTo switch the tool off, release the switch.
Hints for optimum use
Drilling
uUse sharp drill bits only.
uSupport and secure work properly, as instructed in the
Safety Instructions.
uUse appropriate and required safety equipment, as
instructed in the Safety Instructions.
uSecure and maintain work area, as instructed in the
Safety Instructions.
uRun the drill very slowly, using light pressure, until
the hole is started enough to keep the drill bit from slipping
out of it.
uApply pressure in a straight line with the bit. Use enough
pressure to keep the bit biting but not so much as to stall
u
action.
uDO NOT CLICK THE TRIGGER OF A STALLED DRILL
OFF AND ON IN AN ATTEMPT TO START IT. DAMAGE
TO THE DRILL CAN RESULT.
uMinimize stalling on breakthrough by reducing pressure
and slowly drilling through the last part of the hole.
uKeep the motor running while pulling the bit out of a drilled
hole. This will help reduce jamming.
uMake sure switch turns drill on and off.

6
ENGLISH
6
ENGLISH
(Original instructions)
Drilling in wood
Holes in wood can be made with the same twist drill bits used
for metal or with spade bits. These bits should be sharp and
should be pulled out frequently when drilling to clear chips
Drilling in metal
Use a cutting lubricant when drilling metals. The exceptions
are cast iron and brass which should be drilled dry. The cutting
lubricants that work best are sulfurized cutting oil or lard oil.
Screwdriving
uAlways use the correct type and size of screwdriver bit.
u
amount of washing liquid or soap as a lubricant.
uAlways hold the tool and screwdriver bit in a straight line
with the screw
Troubleshooting
Problem Possible cause Possible solution
Unit will not start. Battery pack not
charged.
Check battery pack charg-
ing requirements
Battery pack will not
charge.
Charger not plugged
in.
Surrounding air
temperature too hot or
too cold.
Plug charger into a work-
ing outlet.
Move charger and battery
pack to a surrounding air
temperature of above 40
degrees F (45ºC) or below
105 degrees F (+40.5ºC)
Unit shuts off
abruptly.
Battery pack has
reached its maximum
thermal limit.
Out of charge. (To
maximize the life of
the battery pack it is
designed to shutoff
abruptly when the
charge is depleted
Allow battery pack to cool
down.
Place on charger
and allow to charge.
Accessories
The performance of your tool depends on the accessory used.
BLACK+DECKER accessories are engineered to high quality
standards and designed to enhance the performance of your
tool. By using these accessories you will get the very best
from your tool.
Maintenance
Your BLACK+DECKER tool has been designed to operate
over a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper tool
care and regular cleaning.
Your charger does not require any maintenance apart from
regular cleaning.
Warning! Before performing any maintenance on the tool,
remove the battery from the tool. Unplug the charger before
cleaning it.
uRegularly clean the ventilation slots in your tool and
charger using a soft brush or dry cloth.
uRegularly clean the motor housing using a damp cloth.
Do not use any abrasive or solvent-based cleaner.
uRegularly open the chuck and tap it to remove any dust
from the interior.
Z
z
Z
Protecting the environment.
Separate collection. This product must not be
disposed of with normal household waste.
needs replacement, or if it is of no further use to you, do not
dispose of it with household waste. Make this product
available for separate collection.
Separate collection of used products and packaging
allows materials to be recycled and used again.
Re-use of recycled materials helps prevent
environmental pollution and reduces the demand for
raw materials.
Service Information
Black & Decker offers a full network of company-owned and
authorized service locations throughtout Asia. All Black &
Decker Service Centers are staffed with trained personnel to
provide customers with efficient and reliable product service.
Whether you need technical advice, repair, or genuine factory
replacement parts, contact the Black & Decker location
nearest to you.
NOTE
Black & Decker's policy is one of continuous improvement
to our products and, as such, we reserve the right to
change product specifications without prior notice.
Standard equipment and accessories may vary by country.
Product specifications may differ by country.
Complete product range may not be available in all
countries.
Contact your local Black & Decker dealers for range
availability.
Batteries
There are no user servicable parts inside.
At the end of your products life return the whole unit to your
service agent or to a local recycling station to have the
battery recycled. Do not throw the unit out with household
waste.
u
u
u
u
u
7
ENGLISH
(Original instructions)
Technical data
BDCDD12USB
Voltage VDC 12
No-load speed Min-1 0 - 550 RPM
Max. torque Nm 12.5 / 26
Chuck capacity mm 1 - 10
Max Drilling capacity
Steel/wood mm 10 / 25
Weight kg 0.79 (with battery 1.04)
Battery BDCB12
Voltage Vdc
12
Capacity Ah 1.5
Type Lithium-Ion

7
ENGLISH
6
ENGLISH
(Original instructions)
Drilling in wood
Holes in wood can be made with the same twist drill bits used
for metal or with spade bits. These bits should be sharp and
should be pulled out frequently when drilling to clear chips
Drilling in metal
Use a cutting lubricant when drilling metals. The exceptions
are cast iron and brass which should be drilled dry. The cutting
lubricants that work best are sulfurized cutting oil or lard oil.
Screwdriving
uAlways use the correct type and size of screwdriver bit.
u
amount of washing liquid or soap as a lubricant.
uAlways hold the tool and screwdriver bit in a straight line
with the screw
Troubleshooting
Problem Possible cause Possible solution
Unit will not start. Battery pack not
charged.
Check battery pack charg-
ing requirements
Battery pack will not
charge.
Charger not plugged
in.
Surrounding air
temperature too hot or
too cold.
Plug charger into a work-
ing outlet.
Move charger and battery
pack to a surrounding air
temperature of above 40
degrees F (45ºC) or below
105 degrees F (+40.5ºC)
Unit shuts off
abruptly.
Battery pack has
reached its maximum
thermal limit.
Out of charge. (To
maximize the life of
the battery pack it is
designed to shutoff
abruptly when the
charge is depleted
Allow battery pack to cool
down.
Place on charger
and allow to charge.
Accessories
The performance of your tool depends on the accessory used.
BLACK+DECKER accessories are engineered to high quality
standards and designed to enhance the performance of your
tool. By using these accessories you will get the very best
from your tool.
Maintenance
Your BLACK+DECKER tool has been designed to operate
over a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper tool
care and regular cleaning.
Your charger does not require any maintenance apart from
regular cleaning.
Warning! Before performing any maintenance on the tool,
remove the battery from the tool. Unplug the charger before
cleaning it.
uRegularly clean the ventilation slots in your tool and
charger using a soft brush or dry cloth.
uRegularly clean the motor housing using a damp cloth.
Do not use any abrasive or solvent-based cleaner.
uRegularly open the chuck and tap it to remove any dust
from the interior.
Z
z
Z
Protecting the environment.
Separate collection. This product must not be
disposed of with normal household waste.
needs replacement, or if it is of no further use to you, do not
dispose of it with household waste. Make this product
available for separate collection.
Separate collection of used products and packaging
allows materials to be recycled and used again.
Re-use of recycled materials helps prevent
environmental pollution and reduces the demand for
raw materials.
Service Information
Black & Decker offers a full network of company-owned and
authorized service locations throughtout Asia. All Black &
Decker Service Centers are staffed with trained personnel to
provide customers with efficient and reliable product service.
Whether you need technical advice, repair, or genuine factory
replacement parts, contact the Black & Decker location
nearest to you.
NOTE
Black & Decker's policy is one of continuous improvement
to our products and, as such, we reserve the right to
change product specifications without prior notice.
Standard equipment and accessories may vary by country.
Product specifications may differ by country.
Complete product range may not be available in all
countries.
Contact your local Black & Decker dealers for range
availability.
Batteries
There are no user servicable parts inside.
At the end of your products life return the whole unit to your
service agent or to a local recycling station to have the
battery recycled. Do not throw the unit out with household
waste.
u
u
u
u
u
7
ENGLISH
(Original instructions)
Technical data
BDCDD12USB
Voltage VDC 12
No-load speed Min-1 0 - 550 RPM
Max. torque Nm 12.5 / 26
Chuck capacity mm 1 - 10
Max Drilling capacity
Steel/wood mm 10 / 25
Weight kg 0.79 (with battery 1.04)
Battery BDCB12
Voltage Vdc
12
Capacity Ah 1.5
Type Lithium-Ion

8
2
4 4a
6
7
B
D
68
A
3
C
Intended use
Your BLACK+DECKER BDCDD12USB - Drill, has been
designed for screwdriving applications and for drilling in wood,
metal and plastics. This tool is intended for consumer use
only.
Safety instructions
General power tool safety warnings
@Warning! Read all safety warnings and all
instructions. Failure to follow the warnings
and instructions listed below may result in
Save all warnings and instructions for future reference.
The term "power tool" in all of the warnings listed below refers
to your mains operated (corded) power tool or battery oper-
ated (cordless) power tool.
1. Work area safety
a. Keep work area clean and well lit. Cluttered or dark
areas invite accidents.
b. Do not operate power tools in explosive atmospheres,
or dust. Power tools create sparks which may ignite the
dust or fumes.
c. Keep children and bystanders away while operating a
power tool. Distractions can cause you to lose control.
设计用途
您的 BLACK+DECKER BDCDD12USB - 电钻设计用
于螺丝安装以及在木材、钢材和塑料上钻孔。本工
具仅供专业人士使用。
安全说明
电动工具通用安全警告
警告！阅读随电动工具提供的所有安全警
告、说明、图示和规定。不遵照以下所列
说明会导致电击、着火和／或严重伤害。
2
4 4a
6
7
B
D
68
A
3
C
Intended use
Your BLACK+DECKER BDCDD12USB - Drill, has been
designed for screwdriving applications and for drilling in wood,
metal and plastics. This tool is intended for consumer use
only.
Safety instructions
General power tool safety warnings
@Warning! Read all safety warnings and all
instructions. Failure to follow the warnings
and instructions listed below may result in
Save all warnings and instructions for future reference.
The term "power tool" in all of the warnings listed below refers
to your mains operated (corded) power tool or battery oper-
ated (cordless) power tool.
1. Work area safety
a. Keep work area clean and well lit. Cluttered or dark
areas invite accidents.
b. Do not operate power tools in explosive atmospheres,
or dust. Power tools create sparks which may ignite the
dust or fumes.
c. Keep children and bystanders away while operating a
power tool. Distractions can cause you to lose control.
保存所有警告和说明书以备查阅。
警告中的术语“电动工具”指市电驱动（有线）电
动工具或电池驱动（无线）电动工具。
a) 工作场地的安全
1) 保持工作场地清洁和明亮。杂乱和黑暗的场地会
引发事故。
2) 不要在易爆环境，如有易燃液体、气体或粉尘的
环境下操作电动工具。电动工具产生的火花会点
燃粉尘或气体。
3) 操作电动工具时，远离儿童和旁观者。注意力不
集中会使操作者失去对工具的控制。

9
简体中文
2
4 4a
6
7
B
D
68
A
3
C
Intended use
Your BLACK+DECKER BDCDD12USB - Drill, has been
designed for screwdriving applications and for drilling in wood,
metal and plastics. This tool is intended for consumer use
only.
Safety instructions
General power tool safety warnings
@Warning! Read all safety warnings and all
instructions. Failure to follow the warnings
and instructions listed below may result in
Save all warnings and instructions for future reference.
The term "power tool" in all of the warnings listed below refers
to your mains operated (corded) power tool or battery oper-
ated (cordless) power tool.
1. Work area safety
a. Keep work area clean and well lit. Cluttered or dark
areas invite accidents.
b. Do not operate power tools in explosive atmospheres,
or dust. Power tools create sparks which may ignite the
dust or fumes.
c. Keep children and bystanders away while operating a
power tool. Distractions can cause you to lose control.
b) 电气安全
1) 电动工具插头必须与插座相配。绝不能以任何方
式改装插头。需接地的电动工具不能使用任何转
换插头。未经改装的插头和相配的插座将降低电
击风险。
2) 避免人体接触接地表面，如管道、散热片和冰箱。
如果你身体接地会增加电击风险。
3) 不得将电动工具暴露在雨中或潮湿环境中。水进
入电动工具将增加电击风险。
4) 不得滥用电线。绝不能用软线搬运、拉动电动工
具或拔出其插头。使软线远离热源、油、锐边或
运动部件。受损或缠绕的软线会增加电击风险。
5) 当在户外使用电动工具时，使用适合户外使用的
延长线。适合户外使用的电线将降低电击风险。
6) 如果无法避免在潮湿环境下操作电动工具，应使
用带有剩余电流装置（RCD）保护的电源。RCD
的使用可降低电击风险。
c) 人身安全
1) 保持警觉，当操作电动工具时关注所从事的操作
并保持清醒。当你感到疲倦，或在有药物、酒精
或治疗反应时，不要操作电动工具。在操作电动
工具时瞬间的疏忽会导致严重人身伤害。
2) 使 用 个人 防 护 装 置 。 始 终 佩 戴 护目 镜 。 防护装置，
诸如适当条件下使用防尘面具、防滑安全鞋、安
全帽、听力防护等装置能减少人身伤害。
3) 防止意外起动。在连接电源和 /或电池盒、拿起
或搬运工具前确保开关处于关断位置。手指放
在开关上搬运工具或开关处于接通时通电会导致
危险。
4) 在电动工具接通之前，拿掉所有调节钥匙或扳手。
遗留在电动工具旋转零件上的扳手或钥匙会导致
人身伤害。
5) 手不要过分伸展。时刻注意立足点和身体平衡。
这样能在意外情况下能更好地控制住电动工具。
6) 着装适当。不要穿宽松衣服或佩戴饰品。让你的
头发和衣服远离运动部件。宽松衣服、佩饰或长
发可能会卷入运动部件。
7) 如果提供了与排屑、集尘设备连接用的装置，要
确保其连接完好且使用得当。使用集尘装置可降
低尘屑引起的危险。
8) 不要因为频繁使用工具而产生的熟悉感而掉以轻
心，忽视工具的安全准则。某个粗心的动作可能
在瞬间导致严重的伤害。
d) 电动工具使用和注意事项
1) 不要勉强使用电动工具，根据用途使用合适的电
动工具。选用合适的按照额定值设计的电动工具
会使你工作更有效、更安全。
2) 如果开关不能接通或关断电源，则不能使用该电
动工具。不能通过开关来控制的电动工具是危险
的且必须进行修理。
3) 在进行任何调节、更换附件或贮存电动工具之前，
必须从电源上拔掉插头和／或卸下电池包（如可
拆卸）。这种防护性的安全措施降低了电动工具
意外起动的风险。
4) 将闲置不用的电动工具贮存在儿童所及范围之
外，并且不允许不熟悉电动工具和不了解这些说
明的人操作电动工具。电动工具在未经培训的使
用者手中是危险的。
5) 维护电动工具及其附件。检查运动部件是否调整
到位或卡住，检查零件破损情况和影响电动工具
运行的其他状况。如有损坏，应在使用前修理好
电动工具。许多事故是由维护不良的电动工具引
发的。
6) 保持切削刀具锋利和清洁。维护良好地有锋利切
削刃的刀具不易卡住而且容易控制。
7) 按照使用说明书，并考虑作业条件和要进行的作
业来选择电动工具、附件和工具的刀头等。将电
动工具用于那些与其用途不符的操作可能会导致
危险情况。
8) 保持手柄和握持表面干燥、清洁，不得沾有油脂。
在意外的情况下，湿滑的手柄不能保证握持的安
全和对工具的控制。
e) 电池式工具使用和注意事项
1) 仅使用生产者规定的充电器充电。将适用于某种
电池包的充电器用到其他电池包时可能会发生着
火危险。
2) 仅使用配有专用电池包的电动工具。使用其他电
池包可能会产生伤害和着火危险。
3) 当电池包不用时，将它远离其他金属物体，例如
回形针、硬币、钥匙、钉子、螺钉或其他小金属
物体，以防电池包一端与另一端连接。电池组端
部短路会引起燃烧或着火。
4) 在滥用条件下，液体可能会从电池组中溅出，应
避免接触。如果意外碰到液体，用水冲洗。如果
液体碰到了眼睛，还要寻求医疗帮助。从电池中
溅出的液体可能会发生腐蚀或燃烧。
5) 不要使用损坏或改装过的电池包或工具。损坏或
改装过的电池组可能呈现无法预测的结果，导致
着火、爆炸或伤害。

10
6) 不要将电池包暴露于火或者高温中。电池包暴露
于火或高于 130˚C 的高温中可能导致爆炸。
f) 维修
1) 让专业维修人员使用相同的备件维修电动工具。
这将保证所维修的电动工具的安全。
2) 决不能维修损坏的电池包。电池包仅能由生产者
或其授权的维修服务商进行维修。
－工具使用前应得到适当支撑。由于工具输出转矩
大，运行时没有适当支撑会失控导致人身伤害。
－当在钻削附件可能触及暗线之处进行操作时，要
通过绝缘握持面来握持工具。钻削附件碰到带电
导线会使工具外露的金属零件带电从而使操作者
受到电击。
电动工具附加安全警告
警告！电钻附加安全警告
 请使用工具随附的辅助手柄。操作失手会引起人
身伤害。
 执行操作时如果切割配件可能会接触隐藏的电
线，请握住绝缘手柄表面。切割配件如果接触到
“带电”导线，电动工具金属部件表面就会“带电”
并使操作人员触电。
 使用夹具或其它可行的方法，将工件固定并支撑
到稳定的平台上。手持或用身体顶住工件都是不
稳定的，会导致操作失控。
 在墙上、地板或天花板上钻孔之前，请检查电线
和管道位置。
 不要在钻孔后立刻碰触可能还带热的钻头尖端。
 本使用手册描述了工具的设计用途。使用非本使
用手册所建议的任何其他附件或配件，或者使用
本工具执行非手册建议的任何其他操作，都可能
存在人身伤害和 /或财产损失的危险。
他人安全
 本工具不适合体力、感觉或智力不足，或者缺乏
经验及知识的人员（包括小孩）使用，除非负责
他们安全的人员已经为他们提供关于使用此器具
的监督或指示。
 必须监督儿童，确保他们不将此设备当做玩具来玩。
2
4 4a
6
7
B
D
68
A
3
C
Intended use
Your BLACK+DECKER BDCDD12USB - Drill, has been
designed for screwdriving applications and for drilling in wood,
metal and plastics. This tool is intended for consumer use
only.
Safety instructions
General power tool safety warnings
@Warning! Read all safety warnings and all
instructions. Failure to follow the warnings
and instructions listed below may result in
Save all warnings and instructions for future reference.
The term "power tool" in all of the warnings listed below refers
to your mains operated (corded) power tool or battery oper-
ated (cordless) power tool.
1. Work area safety
a. Keep work area clean and well lit. Cluttered or dark
areas invite accidents.
b. Do not operate power tools in explosive atmospheres,
or dust. Power tools create sparks which may ignite the
dust or fumes.
c. Keep children and bystanders away while operating a
power tool. Distractions can cause you to lose control.
其他风险
使用工具时，可能出现本安全警示之外的其他风险。
这些风险可能来自使用不当、使用时间过长等。尽
管遵守了相关的安全法规并采用了安全装备，某些
其他风险仍然是无法避免的。这些风险包括 ：
 接触旋转 /运动部件时所导致的伤害风险。
 更换部件、锯片或配件时所导致的伤害风险。
 长期使用工具的伤害风险。长期使用任何工具
时，均应定期休息。
 听力损伤。
 吸入工具使用过程中产生的粉尘导致的健康危害
（例如，锯切木材，特别是橡木，山毛榉和中密
度纤维板时）。
工具上的标签
工具上显示下列符号和日期码 ：
警告！为降低伤害风险，用户必须阅读使
用手册。
电池的附加安全说明
电池
 不论基于任何理由，都不要尝试打开电池。
 请勿将电池暴露在水中。
 不要将电池存放在温度可能超过 40ºC 的地方。
 只在环境温度介于 10ºC 和40ºC 之间的情况下充电。
 只能使用本工具随附的充电器为电池充电。
 弃置电池时，请遵循“保护环境”部分所提供的
说明。
不要尝试对损坏的电池充电。
工具仅供室内使用。
部件名称
本工具包含如下部分或全部部件。
1. 变速开关
2. 正/反转滑块
3. 扭矩调节轴环
4. 无锁匙夹头
5. LED 工作灯
6. 电池
7. 电池释放按钮
4
ENGLISH
(Original instructions)
d. Under abusive conditions, liquid may be ejected from
the battery; avoid contact. If contact accidentally
additionally seek medical help. Liquid ejected from the
battery may cause irritation or burns.
6. Service
a.
person using only identical replacement parts. This will
ensure that the safety of the power tool is maintained.
Additional power tool safety warnings
@Warning! Additional safety warnings for
drills
uUse auxiliary handles supplied with the tool. Loss of
control can cause personal injury.
uHold power tool by insulated gripping surfaces when
performing an operation where the cutting accessory
may contact hidden wiring. Cutting accessory contacting
a "live" wire may make exposed metal parts of the power
tool "live" and could give the operator an electric shock.
uUse clamps or another practical way to secure and
support the workpiece to a stable platform. Holding the
work by hand or against your body leaves it unstable and
may lead to loss of control.
u
location of wiring and pipes.
uAvoid touching the tip of a drill bit just after drilling, as it
may be hot.
uThe intended use is described in this instruction manual.
The use of any accessory or attachment or performance
of any operation with this tool other than those recom-
mended in this instruction manual may present a risk of
personal injury and/or damage to property.
Safety of others
uThis tool is not intended for use by persons (including
children) with reduced physical, sensory or mental capa-
bilities, or lack of experience and knowledge, unless they
have been given supervision or instruction concerning use
of the tool by a person responsible for their safety.
uChildren should be supervised to ensure that they do not
play with the appliance.
Residual risks
Additional residual risks may arise when using the tool which
may not be included in the enclosed safety warnings.
These risks can arise from misuse, prolonged use etc.
Even with the application of the relevant safety regulations
and the implementation of safety devices, certain residual
risks can not be avoided. These include:
uInjuries caused by touching any rotating/moving parts.
uInjuries caused when changing any parts, blades or ac-
cessories.
uInjuries caused by prolonged use of a tool. When using
any tool for prolonged periods ensure you take regular
breaks.
uImpairment of hearing.
uHealth hazards caused by breathing dust developed when
using your tool (example:- working with wood, especially
oak, beech and MDF.)
Labels on tool
The following symbols are shown on the tool along with the
date code:
:Warning! To reduce the risk of injury, the user
must read the instruction manual.
Additional safety instructions for batteries
Batteries
uNever attempt to open for any reason.
uDo not expose the battery to water.
uDo not store in locations where the temperature may
exceed 40 °C.
uCharge only at ambient temperatures between 10 °C and
40 °C.
uCharge only using the charger provided with the tool.
uWhen disposing of batteries, follow the instructions given
in the section "Protecting the environment".
pDo not attempt to charge damaged batteries.
$The tool is intend of indoor use only.
Features
This tool includes some or all of the following features.
1. Variable speed switch
2. Forward/reverse slider
3. Torque adjustment collar
4. Keyless chuck
5. LED work light
6. Battery
7. Battery release button
Assembly
Use
Warning! Let the tool work at its own pace. Do not overload.
4
ENGLISH
(Original instructions)
d. Under abusive conditions, liquid may be ejected from
the battery; avoid contact. If contact accidentally
additionally seek medical help. Liquid ejected from the
battery may cause irritation or burns.
6. Service
a.
person using only identical replacement parts. This will
ensure that the safety of the power tool is maintained.
Additional power tool safety warnings
@Warning! Additional safety warnings for
drills
uUse auxiliary handles supplied with the tool. Loss of
control can cause personal injury.
uHold power tool by insulated gripping surfaces when
performing an operation where the cutting accessory
may contact hidden wiring. Cutting accessory contacting
a "live" wire may make exposed metal parts of the power
tool "live" and could give the operator an electric shock.
uUse clamps or another practical way to secure and
support the workpiece to a stable platform. Holding the
work by hand or against your body leaves it unstable and
may lead to loss of control.
u
location of wiring and pipes.
uAvoid touching the tip of a drill bit just after drilling, as it
may be hot.
uThe intended use is described in this instruction manual.
The use of any accessory or attachment or performance
of any operation with this tool other than those recom-
mended in this instruction manual may present a risk of
personal injury and/or damage to property.
Safety of others
uThis tool is not intended for use by persons (including
children) with reduced physical, sensory or mental capa-
bilities, or lack of experience and knowledge, unless they
have been given supervision or instruction concerning use
of the tool by a person responsible for their safety.
uChildren should be supervised to ensure that they do not
play with the appliance.
Residual risks
Additional residual risks may arise when using the tool which
may not be included in the enclosed safety warnings.
These risks can arise from misuse, prolonged use etc.
Even with the application of the relevant safety regulations
and the implementation of safety devices, certain residual
risks can not be avoided. These include:
uInjuries caused by touching any rotating/moving parts.
uInjuries caused when changing any parts, blades or ac-
cessories.
uInjuries caused by prolonged use of a tool. When using
any tool for prolonged periods ensure you take regular
breaks.
uImpairment of hearing.
uHealth hazards caused by breathing dust developed when
using your tool (example:- working with wood, especially
oak, beech and MDF.)
Labels on tool
The following symbols are shown on the tool along with the
date code:
:Warning! To reduce the risk of injury, the user
must read the instruction manual.
Additional safety instructions for batteries
Batteries
uNever attempt to open for any reason.
uDo not expose the battery to water.
uDo not store in locations where the temperature may
exceed 40 °C.
uCharge only at ambient temperatures between 10 °C and
40 °C.
uCharge only using the charger provided with the tool.
uWhen disposing of batteries, follow the instructions given
in the section "Protecting the environment".
pDo not attempt to charge damaged batteries.
$The tool is intend of indoor use only.
Features
This tool includes some or all of the following features.
1. Variable speed switch
2. Forward/reverse slider
3. Torque adjustment collar
4. Keyless chuck
5. LED work light
6. Battery
7. Battery release button
Assembly
Use
Warning! Let the tool work at its own pace. Do not overload.
4
ENGLISH
(Original instructions)
d. Under abusive conditions, liquid may be ejected from
the battery; avoid contact. If contact accidentally
additionally seek medical help. Liquid ejected from the
battery may cause irritation or burns.
6. Service
a.
person using only identical replacement parts. This will
ensure that the safety of the power tool is maintained.
Additional power tool safety warnings
@Warning! Additional safety warnings for
drills
uUse auxiliary handles supplied with the tool. Loss of
control can cause personal injury.
uHold power tool by insulated gripping surfaces when
performing an operation where the cutting accessory
may contact hidden wiring. Cutting accessory contacting
a "live" wire may make exposed metal parts of the power
tool "live" and could give the operator an electric shock.
uUse clamps or another practical way to secure and
support the workpiece to a stable platform. Holding the
work by hand or against your body leaves it unstable and
may lead to loss of control.
u
location of wiring and pipes.
uAvoid touching the tip of a drill bit just after drilling, as it
may be hot.
uThe intended use is described in this instruction manual.
The use of any accessory or attachment or performance
of any operation with this tool other than those recom-
mended in this instruction manual may present a risk of
personal injury and/or damage to property.
Safety of others
uThis tool is not intended for use by persons (including
children) with reduced physical, sensory or mental capa-
bilities, or lack of experience and knowledge, unless they
have been given supervision or instruction concerning use
of the tool by a person responsible for their safety.
uChildren should be supervised to ensure that they do not
play with the appliance.
Residual risks
Additional residual risks may arise when using the tool which
may not be included in the enclosed safety warnings.
These risks can arise from misuse, prolonged use etc.
Even with the application of the relevant safety regulations
and the implementation of safety devices, certain residual
risks can not be avoided. These include:
uInjuries caused by touching any rotating/moving parts.
uInjuries caused when changing any parts, blades or ac-
cessories.
uInjuries caused by prolonged use of a tool. When using
any tool for prolonged periods ensure you take regular
breaks.
uImpairment of hearing.
uHealth hazards caused by breathing dust developed when
using your tool (example:- working with wood, especially
oak, beech and MDF.)
Labels on tool
The following symbols are shown on the tool along with the
date code:
:Warning! To reduce the risk of injury, the user
must read the instruction manual.
Additional safety instructions for batteries
Batteries
uNever attempt to open for any reason.
uDo not expose the battery to water.
uDo not store in locations where the temperature may
exceed 40 °C.
uCharge only at ambient temperatures between 10 °C and
40 °C.
uCharge only using the charger provided with the tool.
uWhen disposing of batteries, follow the instructions given
in the section "Protecting the environment".
pDo not attempt to charge damaged batteries.
$The tool is intend of indoor use only.
Features
This tool includes some or all of the following features.
1. Variable speed switch
2. Forward/reverse slider
3. Torque adjustment collar
4. Keyless chuck
5. LED work light
6. Battery
7. Battery release button
Assembly
Use
Warning! Let the tool work at its own pace. Do not overload.

11
简体中文
组装
使用
警告！请让工具在自有速度下工作。请勿过载。
为电池充电（图 A）
电池在首次使用之前，以及无法像从前一样对工作
轻松提供足够的电量时，都需要充电。电池在充电
时可能会变热 ；这是正常现象，而且并不表示出现
问题。
警告！请勿在环境温度低于 10ºC 或高于 40ºC 的情
况下为电池充电。建议的充电温度大约 24 ºC。
注 ：若电池温度低于约 10ºC 或高于 40ºC，充电器将
不会为电池充电。电池应留在充电器内，充电器会
在电池温度升高或降低到合适温度时自动开始充电。
 如果要为电池充电，请将 USB 充电器 (8) 插入电池。
 将充电器插入合适的电源，并打开电源。
 电池处于放电状态时，请在 1 周内充电。在电力
耗尽状态下保存会大大缩短电池寿命。
警告！火灾危险。断开充电器与工具的连接时，确
保先从插座上拔下充电器插头，然后断开充电器电
源线与工具的连接。
安装及取出电池（图 B）
 要安装电池，请将其与工具上的插座对齐。将电
池滑入插座，然后向上推动直到电池卡入定位。
 要取出电池，请按下释放按钮 (7) ，同时将电池
从插座中拉出。
操作说明
扭矩控制（图 C）
本工具配备用于选择操作模式以及设置扭矩以紧固
螺钉的扭矩调节轴环 (3)。大螺丝和坚硬工件材料，
比小螺丝和柔软工件材料需要更高的扭矩设置。
 要在木材、金属和塑料上钻孔，可将轴环设置到
钻孔位置符号处。
 要执行螺旋操作，将轴环设置到所需设置。如果
尚不知道相应设置，请执行下列操作 ：
 将轴环设置到最低的扭矩设置。
 拧紧第一个螺丝。
 如果离合器在达到所需结果之前松脱，请增加轴
环设置并继续拧紧螺丝。重复直到设置正确为
止。对其余螺丝使用此设置。
自紧式夹头（图 D）
警告！安装或拆卸附件前，请确保锁定按钮已闭合
以避免开关启动。
要插入钻头或其他附件 ：
 以一只手握住夹头 (4a) 的后半部并使用另一只
手以逆时针方向（从夹头末端看）旋转前半部 (4)。
 将钻头或其它配件完全插入夹头，握住夹头后半
部并以顺时针方向旋转前半部，直到看见夹头末
端为止，如此便可牢固地将其扭紧。
警告！不要尝试通过握住夹头前端和打开工具来拧
紧钻头（或任何其它配件）。更换附件时可能会导致
夹头损坏和人身伤害。
钻孔 /螺丝安装
 使用正 /反转滑块 (2)，选择向前或后旋转。
 要打开工具电源，请按下开关 (1) 工具转速取决
于按压开关的程度。
 要关闭工具，请松开开关。
最佳使用提示
钻孔
 请只使用锋利的钻头。
 依照安全指示，适当地支撑和固定工件。
 依照安全指示，使用适当、必要的安全设备。
 依照安全指示，固定和维护工作区域。
 慢慢地让电钻运转，轻轻地施压，直到钻头不会
从所钻的洞中滑出为止。
 用力方向需与钻头呈直线。请施加足够大的压
力，保证钻头钻进所需，但不要大到马达失速或
钻头倾斜。
 请双手紧握电钻，控制电钻的扭转动作。
 请勿试图通过按下、松开触发开关来启动失速的
电钻，否则会损坏电钻。
 减轻压力并慢慢钻过洞的底部，以便将失速穿透
的可能性降至最低。
 从成孔中拉出钻头时，请保持马达运转。这样有
助于避免钻头卡住。
 确保开关可以将电钻启动和关闭。
在木材上钻孔
木材钻孔可以使用和钢材钻孔一样的麻花钻头或扁
钻头。钻头应锋利，且在钻孔时应经常拔出钻头来
清理钻屑。

12
在金属材料上钻孔
在金属上钻孔时，请使用切削润滑剂。但铸铁和黄
铜材料例外，应干钻。效果最佳的切削润滑剂是硫
化切割油或猪油。
螺丝安装
 始终使用正确类型和尺寸的螺丝起子头。
 如果螺钉难以转紧，请尝试用小量洗涤液或肥皂
作为润滑剂。
 工具必须始终与螺丝起子头和螺钉成一直线。
故障排除
问题 可能原因 可能的解决方案
设备不启动。 电池组没有充电。 检查电池组是否需
要充电。
电池组无法充电。 充电器未插电源。
周围气温太高或
太低。
将充电器插入正常
工作的插座。
将充电器和电池组移
至周围气温高于 40ºF
(45ºC) 或低于105ºF
(+40.5ºC) 的地方。
装置突然关闭。 电池组已经达到最
大热界限。
电池耗尽。（为了确
保电池组的使用寿
命最大化，装置会
在电池耗尽时突然
关闭。）
等待电池组冷却。
将电池组放在充电
器上充电。
附件
电动工具的性能取决于所使用的附件。BLACK+DECKER
附件依据高质量标准进行规划，并设计用于增强电
动工具的性能。使用这些配件会令您的工具如虎添翼。
维护
BLACK+DECKER 工具设计精良，可以长期使用，
仅需极少维护。要连续获得令人满意的工作效果，
需要进行合适的工具维护和定期清洁。
除了定期清洁外，本充电器无需其他维护。
警告！在工具上执行任何保养工作之前，请取出工
具内的电池。清洁之前，先拔下充电器插头。
 请使用软刷或干布定期清洁工具和充电器内的通
风槽。
 定期使用湿布清洁电动机外壳。请勿使用任何研
磨性或溶剂型清洁剂。
 请定期打开夹头并轻敲，以去除内部的任何粉尘。
保护环境。
分类回收。本产品不得与普通家庭垃圾一
起处理。
若您发现您的产品需要进行替换，或您已经不再需
要使用这些产品，请不要将它们与家庭废物一起处
置。请将它们单独分类回收。
分类回收使用过的产品和包装能够让材料
得以再循环和再利用。再生材料的再利用
有助于防止环境污染，并降低对原材料的
需求。
服务信息
Black & Decker 提供覆盖整个亚洲的公司隶属和授权
服务地点。所有的 Black & Decker 服务中心都具有
训练有素的人员，为客户提供高效和可靠的产品服
务。不论您是需要技术建议、维修或原厂替换部件，
请联系最靠近您的 Black & Decker 地点。
注
 Black & Decker 的政策是持续改进我们的产品，
因此，我们保留随时更改产品规格的权利，恕不
另行通知。
 标准设备和附件可能会因国家（地区）而异。
 不同国家（地区）的产品规格也可能会有所不同。
 并非所有的国家（地区）都可提供完整的产品
系列。
有关各产品系列的供应情况，请联系您当地的
Black & Decker 代理商。
6
ENGLISH
(Original instructions)
Drilling in wood
Holes in wood can be made with the same twist drill bits used
for metal or with spade bits. These bits should be sharp and
should be pulled out frequently when drilling to clear chips
Drilling in metal
Use a cutting lubricant when drilling metals. The exceptions
are cast iron and brass which should be drilled dry. The cutting
lubricants that work best are sulfurized cutting oil or lard oil.
Screwdriving
uAlways use the correct type and size of screwdriver bit.
u
amount of washing liquid or soap as a lubricant.
uAlways hold the tool and screwdriver bit in a straight line
with the screw
Troubleshooting
Problem Possible cause Possible solution
Unit will not start. Battery pack not
charged.
Check battery pack charg-
ing requirements
Battery pack will not
charge.
Charger not plugged
in.
Surrounding air
temperature too hot or
too cold.
Plug charger into a work-
ing outlet.
Move charger and battery
pack to a surrounding air
temperature of above 40
degrees F (45ºC) or below
105 degrees F (+40.5ºC)
Unit shuts off
abruptly.
Battery pack has
reached its maximum
thermal limit.
Out of charge. (To
maximize the life of
the battery pack it is
designed to shutoff
abruptly when the
charge is depleted
Allow battery pack to cool
down.
Place on charger
and allow to charge.
Accessories
The performance of your tool depends on the accessory used.
BLACK+DECKER accessories are engineered to high quality
standards and designed to enhance the performance of your
tool. By using these accessories you will get the very best
from your tool.
Maintenance
Your BLACK+DECKER tool has been designed to operate
over a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper tool
care and regular cleaning.
Your charger does not require any maintenance apart from
regular cleaning.
Warning! Before performing any maintenance on the tool,
remove the battery from the tool. Unplug the charger before
cleaning it.
uRegularly clean the ventilation slots in your tool and
charger using a soft brush or dry cloth.
uRegularly clean the motor housing using a damp cloth.
Do not use any abrasive or solvent-based cleaner.
uRegularly open the chuck and tap it to remove any dust
from the interior.
Z
z
Z
Protecting the environment.
Separate collection. This product must not be
disposed of with normal household waste.
needs replacement, or if it is of no further use to you, do not
dispose of it with household waste. Make this product
available for separate collection.
Separate collection of used products and packaging
allows materials to be recycled and used again.
Re-use of recycled materials helps prevent
environmental pollution and reduces the demand for
raw materials.
Service Information
Black & Decker offers a full network of company-owned and
authorized service locations throughtout Asia. All Black &
Decker Service Centers are staffed with trained personnel to
provide customers with efficient and reliable product service.
Whether you need technical advice, repair, or genuine factory
replacement parts, contact the Black & Decker location
nearest to you.
NOTE
Black & Decker's policy is one of continuous improvement
to our products and, as such, we reserve the right to
change product specifications without prior notice.
Standard equipment and accessories may vary by country.
Product specifications may differ by country.
Complete product range may not be available in all
countries.
Contact your local Black & Decker dealers for range
availability.
Batteries
There are no user servicable parts inside.
At the end of your products life return the whole unit to your
service agent or to a local recycling station to have the
battery recycled. Do not throw the unit out with household
waste.
u
u
u
u
u
6
ENGLISH
(Original instructions)
Drilling in wood
Holes in wood can be made with the same twist drill bits used
for metal or with spade bits. These bits should be sharp and
should be pulled out frequently when drilling to clear chips
Drilling in metal
Use a cutting lubricant when drilling metals. The exceptions
are cast iron and brass which should be drilled dry. The cutting
lubricants that work best are sulfurized cutting oil or lard oil.
Screwdriving
uAlways use the correct type and size of screwdriver bit.
u
amount of washing liquid or soap as a lubricant.
uAlways hold the tool and screwdriver bit in a straight line
with the screw
Troubleshooting
Problem Possible cause Possible solution
Unit will not start. Battery pack not
charged.
Check battery pack charg-
ing requirements
Battery pack will not
charge.
Charger not plugged
in.
Surrounding air
temperature too hot or
too cold.
Plug charger into a work-
ing outlet.
Move charger and battery
pack to a surrounding air
temperature of above 40
degrees F (45ºC) or below
105 degrees F (+40.5ºC)
Unit shuts off
abruptly.
Battery pack has
reached its maximum
thermal limit.
Out of charge. (To
maximize the life of
the battery pack it is
designed to shutoff
abruptly when the
charge is depleted
Allow battery pack to cool
down.
Place on charger
and allow to charge.
Accessories
The performance of your tool depends on the accessory used.
BLACK+DECKER accessories are engineered to high quality
standards and designed to enhance the performance of your
tool. By using these accessories you will get the very best
from your tool.
Maintenance
Your BLACK+DECKER tool has been designed to operate
over a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper tool
care and regular cleaning.
Your charger does not require any maintenance apart from
regular cleaning.
Warning! Before performing any maintenance on the tool,
remove the battery from the tool. Unplug the charger before
cleaning it.
uRegularly clean the ventilation slots in your tool and
charger using a soft brush or dry cloth.
uRegularly clean the motor housing using a damp cloth.
Do not use any abrasive or solvent-based cleaner.
uRegularly open the chuck and tap it to remove any dust
from the interior.
Z
z
Z
Protecting the environment.
Separate collection. This product must not be
disposed of with normal household waste.
needs replacement, or if it is of no further use to you, do not
dispose of it with household waste. Make this product
available for separate collection.
Separate collection of used products and packaging
allows materials to be recycled and used again.
Re-use of recycled materials helps prevent
environmental pollution and reduces the demand for
raw materials.
Service Information
Black & Decker offers a full network of company-owned and
authorized service locations throughtout Asia. All Black &
Decker Service Centers are staffed with trained personnel to
provide customers with efficient and reliable product service.
Whether you need technical advice, repair, or genuine factory
replacement parts, contact the Black & Decker location
nearest to you.
NOTE
Black & Decker's policy is one of continuous improvement
to our products and, as such, we reserve the right to
change product specifications without prior notice.
Standard equipment and accessories may vary by country.
Product specifications may differ by country.
Complete product range may not be available in all
countries.
Contact your local Black & Decker dealers for range
availability.
Batteries
There are no user servicable parts inside.
At the end of your products life return the whole unit to your
service agent or to a local recycling station to have the
battery recycled. Do not throw the unit out with household
waste.
u
u
u
u
u

13
简体中文
电池
这些组件内没有可供用户维修的零件。
 产品生命周期结束后，请将整个装置送到您的服
务代理处或当地的回收站，以便回收电池。切勿
将本设备与生活垃圾混合弃置。
技术参数
BDCDD12USB
电压 伏特直流 12
空载转速 转/分0 - 550 转/分
最大扭矩 牛米 12.5 / 26
夹头尺寸 毫米 1 – 10
最大钻孔能力
钢材 /木材 毫米 10 / 25
重量 千克 0.79（含电池时则为 1.04）
电池 BDCB12
电压 伏特直流 12
电池容量 安时 1.5
类型 锂离子电池
6
ENGLISH
(Original instructions)
Drilling in wood
Holes in wood can be made with the same twist drill bits used
for metal or with spade bits. These bits should be sharp and
should be pulled out frequently when drilling to clear chips
Drilling in metal
Use a cutting lubricant when drilling metals. The exceptions
are cast iron and brass which should be drilled dry. The cutting
lubricants that work best are sulfurized cutting oil or lard oil.
Screwdriving
uAlways use the correct type and size of screwdriver bit.
u
amount of washing liquid or soap as a lubricant.
uAlways hold the tool and screwdriver bit in a straight line
with the screw
Troubleshooting
Problem Possible cause Possible solution
Unit will not start. Battery pack not
charged.
Check battery pack charg-
ing requirements
Battery pack will not
charge.
Charger not plugged
in.
Surrounding air
temperature too hot or
too cold.
Plug charger into a work-
ing outlet.
Move charger and battery
pack to a surrounding air
temperature of above 40
degrees F (45ºC) or below
105 degrees F (+40.5ºC)
Unit shuts off
abruptly.
Battery pack has
reached its maximum
thermal limit.
Out of charge. (To
maximize the life of
the battery pack it is
designed to shutoff
abruptly when the
charge is depleted
Allow battery pack to cool
down.
Place on charger
and allow to charge.
Accessories
The performance of your tool depends on the accessory used.
BLACK+DECKER accessories are engineered to high quality
standards and designed to enhance the performance of your
tool. By using these accessories you will get the very best
from your tool.
Maintenance
Your BLACK+DECKER tool has been designed to operate
over a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper tool
care and regular cleaning.
Your charger does not require any maintenance apart from
regular cleaning.
Warning! Before performing any maintenance on the tool,
remove the battery from the tool. Unplug the charger before
cleaning it.
uRegularly clean the ventilation slots in your tool and
charger using a soft brush or dry cloth.
uRegularly clean the motor housing using a damp cloth.
Do not use any abrasive or solvent-based cleaner.
uRegularly open the chuck and tap it to remove any dust
from the interior.
Z
z
Z
Protecting the environment.
Separate collection. This product must not be
disposed of with normal household waste.
needs replacement, or if it is of no further use to you, do not
dispose of it with household waste. Make this product
available for separate collection.
Separate collection of used products and packaging
allows materials to be recycled and used again.
Re-use of recycled materials helps prevent
environmental pollution and reduces the demand for
raw materials.
Service Information
Black & Decker offers a full network of company-owned and
authorized service locations throughtout Asia. All Black &
Decker Service Centers are staffed with trained personnel to
provide customers with efficient and reliable product service.
Whether you need technical advice, repair, or genuine factory
replacement parts, contact the Black & Decker location
nearest to you.
NOTE
Black & Decker's policy is one of continuous improvement
to our products and, as such, we reserve the right to
change product specifications without prior notice.
Standard equipment and accessories may vary by country.
Product specifications may differ by country.
Complete product range may not be available in all
countries.
Contact your local Black & Decker dealers for range
availability.
Batteries
There are no user servicable parts inside.
At the end of your products life return the whole unit to your
service agent or to a local recycling station to have the
battery recycled. Do not throw the unit out with household
waste.
u
u
u
u
u

N56340 8
10/2017