Black & Decker BXWP60002 User manual

Please read before returning this product for any reason.
INSTRUCTION MANUAL
DRILL PUMP
DRILL PUMP KIT
BXWP60002
BXWP60005
Customer Support
(855-222-3033)
customer[email protected]

2
Important
Read these warnings carefully. Know the application and limitations of
this drill pump. Failure to follow these warnings could result in serious
bodily injury and/or property damage.
Safety Guidelines
Carefully read, understand and follow all safety instructions
in this manual.
This is the safety alert symbol. When you see this symbol,
look for one of the following signal words.
DANGER: Indicates a hazardous situation which, if not avoided, will result in
death or serious injury.
WARNING: Indicates a hazardous situation which, if not avoided, could result
in death or serious injury.
CAUTION: Indicates a hazardous situation which, if not avoided, could result in
minor or moderate injury.
NOTICE: Indicates to address practices not related to personal injury.
DANGER: Fire hazard. Never pump gasoline or other volatile or ammable
liquids with this unit.
CAUTION: Follow all safety precautions recommended by the manufacturer of
the electric drill*.
CAUTION: Always disconnect drill from power source and remove the pump
from drill before attempting to service or perform maintenance.
WARNING RISK OF ELECTRICAL SHOCK: For corded or battery operated
drill* follow drill manufacturers instructions.
CAUTION: Inspect hoses and/or tubing before each use. Using worn or leaking
hoses can prevent the pump from working properly.
NOTICE: Suction hose/tubing should be as short as possible, kink free, and non-
collapsible. Be certain the suction line is air tight. Any leaks may prevent the pump
from priming.
NOTICE: Do not run the drill pump dry. The drill pump housing must be lled
with liquid during operation. Operating the drill pump dry for as little as 30 seconds
can cause damage and result in premature failure of the drill pump. Running the drill
pump dry will also void the warranty.
NOTICE: The drill pump is lubricated at the factory for the rst use. It is
recommended to add a few drops of lubricating oil to the inlet port of the drill pump
before each use to aid with priming and to prevent the impeller from running dry.
Cooking oil or mineral oil are suitable options.
NOTICE: A screen or strainer (not included) should be used when pumping uids
that contain abrasives or small solids to prevent damage to the pump.
ENGLISH
Description
Versatile drill powered pump used to transfer non-explosive
or non-corrosive liquid from sinks, tanks, water heaters,
aquariums, window wells, bathtubs, etc. This pump is
designed to work with most power drills rated up to 2800
RPM. A drill with a minimum 1/4” chuck is required. NOTE:
DRILL SOLD SEPARATELY. Drill not included with any model. Tubing
& Hose included only with model BXWP60005
Specications
BXWP60002 BXWP60005
Max Flow Rate at 2800 RPM at 0 ft. discharge height 225 GPH (852 LPH) 225 GPH (852 LPH)
Max Flow Rate at 800 RPM at 0 ft. discharge height 140 GPH (530 LPH) 140 GPH (530 LPH)
Maximum Discharge Head at 2800 RPM 45 ft. (13.7 m) 45 ft. (13.7 m)
Maximum Discharge Head at 800 RPM 32 ft. (9.7 m) 32 ft. (9.7 m)
Self-Priming Height Up to 8 ft. (2.4 m) Vertically Up to 8 ft. (2.4 m) Vertically
Min. Drill RPM (Recommended) 800 800
Max. Drill RPM 2800 2800
Drill Chuck Size 1/4 in. (6.4 mm) or Larger 1/4 in. (6.4 mm) or Larger
Construction Thermoplastic Thermoplastic
Suction 3/4 in. (19 mm) GHT or 3/8 in. (9.5 mm) 3/4 in. (19 mm) GHT or 3/8 in. (9.5 mm)
Discharge 3/4 in. (19 mm) GHT or 3/8 in. (9.5 mm) 3/4 in. (19 mm) GHT or 3/8 in. (9.5 mm)
Min Liquid Temp 35° F (2° C) 35° F (2° C)
Max Liquid Temp 120° F (48° C) 120° F (48° C)
Drive Shaft Corrosion Resistant Steel Corrosion Resistant Steel
3 in. x 3/8 in. Adapter Tube Not Included Included
30 in. x 1/4 in. Suction Tube Not Included Included
36 in. x 1/2 in. Garden Hose with female tting Not Included Included
Drill not included with any model

3
ENGLISH
WARNING RISK OF ELECTRICAL SHOCK: For corded
or battery operated drill follow drill manufacturers instructions.
Installation and Operation
NOTE: It is recommended to add a few drops of lubricating
oil to the inlet port before each use to prevent impeller from
running dry.
1. Connect the pump drive shaft to the chuck of the drill
and tighten.
2. If desired, attach the drill pump to a solid surface by
securing with two screws (not included) through
mounting slots.
3. Attach the suction hose/s: (Hose/tubing is included only
with model BXWP60005)
A: Garden Hose: Attach the included garden hose
(model BXWP60005 only) or standard garden hose to
the inlet port of the pump. NOTE: Keep the inlet hose
as short as possible. The inlet hose should not exceed
more than 8 ft. vertical or 25 ft. horizontal distance.
B: Suction Tube: (included with model BXWP60005
only) Insert the 3 in. x 3/8 in. (76 x 9.5 mm) adapter
tube to the inside of the inlet port. Insert the 1/4 in. x
30 in. (6.4 x 762 mm ) suction tube to the inside of the
adapter tube. NOTE: The adapter and suction tubes are
a friction t and should be fully inserted.
4. Attach a standard garden hose to outlet port of the
pump. If the included garden hose is not being used on
the suction port, it may be used for the discharge.
5. Be certain that the suction hose/tube is fully submerged
into liquid source.
6. Connect the drill to the power source. (Refer to drill
manufacturer’s instructions for proper operation.)
7. With drill in the forward position, press the trigger of the
drill to start pumping. NOTE: If pump fails to prime and
start pumping within 15-20 seconds, disconnect the drill
from the power source, ll intake hose with liquid and
restart the pumping process. Do not run the pump dry.
8. After each use, thoroughly ush the pump with clean
water.
Components
1 Drive Shaft
2 3/4 in. (19mm) GHT Suction Port
3 3/4 in. (19mm) GHT Discharge Port
4 36 in. x 3/4 in. (914 x 9mm) GHT Garden Hose**
5 30 in. x 1/4 in. (762 x mm) Suction Hose**
6 3 in. x 3/8 in. (76.2 mm) Adapter Tube**
7 Mounting Screws*
8 Drill*
Installation and Operation: BXWP60002 and BXWP60005
2
*Not Included
7*
1
8*
4*
3
7*
9**
**Included in BXWP60005 Only
6**
5**
R
O
T
A
T
I
O
N

4
ENGLISH
1. Thoroughly ush the pump with clean water after each use.
2. Inspect drive shaft and suction / discharge threads for signs of wear.
3. Inspect all hoses/tubing for signs of wear. Replace if necessary.
Maintenance
Problem Possible Causes How To Correct
Pump will not prime or move liquid.
Air is leaking into the inlet hose or connection. Check connections to ensure they are tight. Inspect rubber
washer in the hose tting. Replace if necessary.
The inlet hose is clogged. Clear the clog or replace the hose.
The impeller, body, and end cover are worn or
damaged from pumping abrasives. Replace the drill pump.
The impeller is worn or damaged from running
the pump dry. Replace the drill pump.
The shaft turns but the impeller does not turn. Replace the drill pump.
Pump running but ow rate not
sucient.
The drill is running too slowly. Increase the drill speed to maximum 2800 rpm.
Restriction in the inlet or discharge hose(s). Clear restriction or replace the hose(s). Check hoses to
eliminate any kinks in the lines.
Liquid is leaking where the shaft
enters the drill pump body.
The seal is worn or damaged. Replace the drill pump.
Troubleshooting
Manufactured Under License By: Pedrollo Group Inc.
45 Maryland Ave East - St. Paul, Minnesota 55117
Copyright ©2022
BLACK & DECKER, BLACK+DECKER, the BLACK & DECKER and BLACK+DECKER logos and product names and the orange and black color scheme are trademarks of The
Black & Decker Corporation and are used under license. Product may dier fromthat pictured. Does not aect function. Not all accessories shown in photography are
included in this package.
Customer Support
(855-222-3033)
[e-mail]
Form #: 60001010/22
Limited Warranty:
Manufacturer warrants the products specied in this warranty to be free from
defects in material or workmanship for ninety (90) days from date of purchase.
During the time period and subject to the terms and conditions, manufacturer will
repair or replace to the original user or consumer any portion of this product which
proves to be defective due to materials or workmanship. At all times, manufacturer
shall have and possess the sole right and option to determine whether to repair or
replace defective equipment, parts or components. Manufacturer has the option
to inspect any product returned under warranty to conrm that the warranty
applies before repair or replacement under warranty is approved. This warranty
sets forth manufacturer’s sole obligation and purchaser’s exclusive remedy for
defective product. For warranty consideration, call 855-222-3033 or email at
[email protected].
Warranty Period:
If, within the duration of product use by the original user, this product proves
to be defective due to materials or workmanship, the product shall be repaired
or replaced at the manufacturer’s option, subject to the terms and conditions
set forth in this warranty statement. Proof of purchase is required for warranty
consideration. In the absence of suitable proof of the purchase date, the eective
period of this warranty is 90 days from the product’s date of manufacture. If a
warranty replacement pump is provided to the customer, the warranty of the
replacement pump will be subject to the original purchase date of the original
pump.
Labor, ETC, Costs:
The manufacturer shall IN NO EVENT be responsible or liable for the cost of eld
labor or other charges incurred by any customer in removing and/or axing any
product, part, or component thereof.
Product Improvements:
The manufacturer reserves the right to change or improve its products or
any portions thereof without being obligated to provide such a change or
improvement for units sold and/or shipped prior to such change or improvement.
General Terms and Conditions:
This warranty shall not apply to damage due to acts of God, normal wear and
tear, normal maintenance services and the parts used in connection with such
service, lightning or conditions beyond the control of the manufacturer, nor shall
it apply to products which, in the sole judgment of the manufacturer, have been
subject to negligence, abuse, accident, misapplication, tampering, alteration; nor
due to improper installation, operation, maintenance or storage; nor to excess of
recommended maximums as set forth in the instructions.
Warranty will be VOID if any of the following conditions are found:
1. Product is used for purposes other than those for which it was designed and
manufactured. Pump has been used for pumping liquids above 120°F.
2. Product is not installed in accordance with applicable codes, ordinances, and
good trade practices.
3. Pump has been exposed to but not limited to the following: sand, gravel,
cement, grease, plaster, mud, tar, gasoline, solvents or other abrasive or
corrosive substances.
4. Pump has been allowed to operate dry (liquid supply cut o ).
Disclaimer:
Any oral statements about the product made by the seller, the manufacturer,
the representatives, or any other parties do not constitute warranties, shall
not be relied upon by the user, and are not part of the contract for sale. Seller’s
and the manufacturer’s only obligation, and buyer’s only remedy, shall be the
replacement and/or repair by the manufacturer of the product as described
above. NEITHER SELLER NOR THE MANUFACTURER SHALL BE LIABLE FOR ANY INJURY, LOSS OR
DAMAGE, DIRECT, INCIDENTAL OR CONSEQUENTIAL (INCLUDING, BUT NOT LIMITED TO, INCIDENTAL
OR CONSEQUENTIAL DAMAGES FOR LOST PROFITS, LOST SALES, INJURY TO PERSON OR PROPERTY,
OR ANY OTHER INCIDENTAL OR CONSEQUENTIAL LOSS), ARISING OUT OFTHE USE OR THE INABILITY
TO USE THE PRODUCT, AND THE USER AGREES THAT NO OTHER REMEDY SHALL BE AVAILABLE TO
IT. Before using, the user shall determine the suitability of the product for their
intended use, and user assumes all risk and liability whatsoever in connection
therewith.
THE WARRANTY AND REMEDY DESCRIBED INTHIS LIMITED WARRANTY IS AN EXCLUSIVE WARRANTY
AND REMEDY AND IS IN LIEU OF ANY OTHER WARRANTY OR REMEDY, EXPRESSED OR IMPLIED,
WHICH OTHER WARRANTIES AND REMEDIES ARE HEREBY EXPRESSLY EXCLUDED, INCLUDING BUT
NOT LIMITED TO ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR
PURPOSE, TO THE EXTENT EITHER APPLIES TO A PRODUCT SHALL BE LIMITED IN DURATION TO THE
PERIODS OF THE EXPRESSEDWARRANTIES GIVEN ABOVE.
Some states and countries do not allow the exclusion or limitations on how
long an implied warranty lasts or the exclusion or limitation of incidental or
consequential damages, so the above exclusion or limitations may not apply to
you. This warranty gives you specic legal rights, and you may also have other
rights which vary from state to state.