Black & Decker HD555 User manual

HD555
HD555K
HD565K
English
简体中文
03
07
Hammer Drill

FIG. A
FIG. C
FIG. E
FIG. B
FIG. D
FIG. F
4
5
6
3
2
1
7
10
11
8
9
3
7
6
7
fThe illustratrions are for representative purposes only, they can differ from actual product.
►Theillustratrionsareforrepresentativepurposesonly,theycandifferfromactualproduct.
►
这些图解只具有代表性意义，与实际产品可能存在差别。
FIG.A
FIG.C
FIG.E
FIG.B
FIG.D
FIG.F

ENGLISH●3
HD555/HD555K/HD565K
HAMMERDRILL
SPECIFICATIONS
Power W 550
Voltage V/Hz 220/50
No-load speed min(rpm) 0-2800
Blows per minute bpm 0-45000
Max drill capacity
Steel mm 13
Concrete mm 13
Wood mm 20
GENERALSAFETYRULES
4 • ENGLISH
4 • ENGLISH
making any adjustments, changing accessories,
or storing power tools. Such preventive safety measures
reduce the risk of starting the power tool accidentally.
d. Store idle power tools out of the reach of children
and do not allow persons unfamiliar with the power
tool or these instructions to operate the power
tool. Power tools are dangerous in the hands
of untrained users.
e. Maintain power tools. Check for misalignment
or binding of moving parts, breakage of par ts and
any other condition that may affect the power
tools operation. If damaged, have the power tool
repaired before use. Many accidents are caused by
poorly maintained power tools.
f. Keep cutting tools sharp and clean.Properly
maintained cutting tools with sharp cutting edges are
less likely to bind and are easier to control.
5. Service
a. Have your power tool serviced by a qualified
repair person using only identical replacement
parts. This will ensure that the safety of the power
tool is maintained.
6. Electrical safety
Your tool is double insulated; therefore no earth
wire is required. Always check that the main voltage
corresponds to the voltage on the rating plate.
Warning! If the power cord is damaged, it must
be replaced by the manufacturer, authorized
BLACK+DECKER Service Center or an equally
qualified person in order to avoid damage or
injury. If the power cord is replaced by an equally
7. Labels on tool
The label on your tool may include the following symbols:
FEATURES (Fig. A)
1. Variable speed switch
2. Lock-on button
3. Forward/reverse slider
4. Drilling mode selector
5. Chuck
6. Depth stop
7. Side handle
ADDITIONAL SAFETY INSTRUCTIONS
FOR HAMMER DRILL
fWear ear protectors with impact drills. Exposure to
noise can cause hearing loss.
fUse auxiliary handles supplied with the tool. Loss
of control can cause personal injur y.
fHold power tool by insulated gripping surfaces
when performing an operation where the cutting
tool may contact hidden wiring or its own cord.
Contact with a “live” wire will also make exposed metal
parts of the power tool “live” and shock the operator.
fUse clamps or another practical way to secure
and support the workpiece to a stable platform.
Holding the work by hand or against your body leaves
it unstable and may lead to loss of control.
fBefore drilling into walls, floors or ceilings check for
the location of wiring and pipes.
fAvoid touching the tip of a drill bit just after drilling, as
it may be hot
ASSAMBLY
Warning! Before assembly, make sure that the tool is
switched off and unplugged.
Fitting the side handle and depth stop (Fig. B)
Turn the grip counterclockwise until you can slide the
side handle (7) onto the front of the tool as shown.
fRotate the side handle into the desired position.
fInsert the depth stop (6) into the mounting hole as
shown.
fSet the drilling depth as described below.
fTighten the side handle by turning the grip clockwise.
Fitting a drill bit or screwdriver bit
Keyed chuck (Fig. C)
fOpen the chuck by turning the sleeve (9)
counterclockwise.
fInsert the bit shaft (8) into the chuck.
fInsert the chuck key (10) into each hole (11) in the side
of the chuck and turn clockwise until tight.
Removing and refitting the chuck (Fig. D)
fOpen the chuck as far as possible.
fRemove the chuck retaining screw, located in the
chuck, by turning it clockwise using a screwdriver.
fTighten an Allen key into the chuck and strike it with
a hammer as shown.
fRemove the Allen key.
fRemove the chuck by turning it counterclockwise.
fTo refit the chuck, screw it onto the spindle and secure
it with the chuck retaining screw.
Read
Instructions
Manual
Use Eye
Protection
Use Ear
Protection
V ........ Volts
A ........ Amperes
Hz ....... Hert z
W ........ Watts
min ..... minutes
..... Alternating
Current
..... Direct
Current
n0....... No-Load
Speed
...... Class II
Construction
.... Earthing
Terminal
.... Safety A lert
Symbol
.../min.. Revolut ions
or Recipr o-
cation p er
minute
qualified person, but not authorized by
BLACK+DECKER, the warranty will not be valid.
Warning! Read and understand all instructions. Failure
to follow all instructions listed below, may result in electric
shock, re and/or serious personal injury.
SAVETHESEINSTRUCTIONS
SAFETYINSTRUCTIONS
Generalpowertoolsafetywarnings.
Warning!Readallsafetywarningsandallin-
structions.Failure to follow the warnings and instructions listed
below may result in electric shock, re and/or serious injury.
Saveallwarningsandinstructionsforfuturereference.
The term “power tool” in all of the warnings listed below
refers to your mains operated (corded) power tool or
battery operated (cordless) power tool.
1. WorkAreaSafety
a. Keepworkareacleanandwelllit. Cluttered and dark
areas invite accidents.
b. Donotoperatepowertoolsinexplosiveatmo-
spheres,suchasinthepresenceofammable
liquids,gasesordust. Power tools create sparks which
may ignite the dust or fumes.
c. Keepchildrenandbystandersawaywhileoperating
apowertool. Distractions can cause you to lose control.
2. ElectricalSafety
a. Powertoolplugsmustmatchtheoutlet. Never modify
the plug in any way. Do not use any adapter plugs with
4 • ENGLISH
4 • ENGLISH
making any adjustments, changing accessories,
or storing power tools. Such preventive safety measures
reduce the risk of starting the power tool accidentally.
d. Store idle power tools out of the reach of children
and do not allow persons unfamiliar with the power
tool or these instructions to operate the power
tool. Power tools are dangerous in the hands
of untrained users.
e. Maintain power tools. Check for misalignment
or binding of moving parts, breakage of parts and
any other condition that may affect the power
tools operation. If damaged, have the power tool
repaired before use. Many accidents are caused by
poorly maintained power tools.
f. Keep cutting tools sharp and clean.Properly
maintained cutting tools with sharp cutting edges are
less likely to bind and are easier to control.
5. Service
a. Have your power tool serviced by a qualified
repair person using only identical replacement
parts. This will ensure that the safety of the power
tool is maintained.
6. Electrical safety
Your tool is double insulated; therefore no earth
wire is required. Always check that the main voltage
corresponds to the voltage on the rating plate.
Warning! If the power cord is damaged, it must
be replaced by the manufacturer, authorized
BLACK+DECKER Service Center or an equally
qualified person in order to avoid damage or
injury. If the power cord is replaced by an equally
7. Labels on tool
The label on your tool may include the following symbols:
FEATURES (Fig. A)
1. Variable speed switch
2. Lock-on button
3. Forward/reverse slider
4. Drilling mode selector
5. Chuck
6. Depth stop
7. Side handle
ADDITIONAL SAFETY INSTRUCTIONS
FOR HAMMER DRILL
fWear ear protectors with impact drills. Exposure to
noise can cause hearing loss.
fUse auxiliary handles supplied with the tool. Loss
of control can cause personal injury.
fHold power tool by insulated gripping surfaces
when performing an operation where the cutting
tool may contact hidden wiring or its own cord.
Contact with a “live” wire will also make exposed metal
parts of the power tool “live” and shock the operator.
fUse clamps or another practical way to secure
and support the workpiece to a stable platform.
Holding the work by hand or against your body leaves
it unstable and may lead to loss of control.
fBefore drilling into walls, floors or ceilings check for
the location of wiring and pipes.
fAvoid touching the tip of a drill bit just after drilling, as
it may be hot
ASSAMBLY
Warning! Before assembly, make sure that the tool is
switched off and unplugged.
Fitting the side handle and depth stop (Fig. B)
Turn the grip counterclockwise until you can slide the
side handle (7) onto the front of the tool as shown.
fRotate the side handle into the desired position.
fInsert the depth stop (6) into the mounting hole as
shown.
fSet the drilling depth as described below.
fTighten the side handle by turning the grip clockwise.
Fitting a drill bit or screwdriver bit
Keyed chuck (Fig. C)
fOpen the chuck by turning the sleeve (9)
counterclockwise.
fInsert the bit shaft (8) into the chuck.
fInsert the chuck key (10) into each hole (11) in the side
of the chuck and turn clockwise until tight.
Removing and refitting the chuck (Fig. D)
fOpen the chuck as far as possible.
fRemove the chuck retaining screw, located in the
chuck, by turning it clockwise using a screwdriver.
fTighten an Allen key into the chuck and strike it with
a hammer as shown.
fRemove the Allen key.
fRemove the chuck by turning it counterclockwise.
fTo refit the chuck, screw it onto the spindle and secure
it with the chuck retaining screw.
Read
Instructions
Manual
Use Eye
Protection
Use Ear
Protection
V ........ Volts
A ........ Amperes
Hz ....... Hertz
W ........ Watts
min ..... minutes
..... Alternating
Current
..... Direct
Current
n0....... No-Load
Speed
...... Class II
Construction
.... Earthing
Terminal
.... Safety Alert
Symbol
.../min.. Revolutions
or Recipro-
cation per
minute
qualified person, but not authorized by
BLACK+DECKER, the warranty will not be valid.
earthed (grounded) power tools. Unmodied plugs and
matching outlets will reduce risk of electric shock.
b. Avoidbodycontactwithearthedorgroundedsurfac-
essuchaspipes,radiators,rangesandrefrigerators.
There is an increased risk of electric shock if your body
is earthed or grounded.
c. Donotexposepowertoolstorainorwetconditions.
Water entering a power tool will increase the risk of
electric shock.
d. Donotabusethecord.Neverusethecordforcarry-
ing,pullingorunpluggingthepowertool.Keepcord
awayfromheat,oil,sharpedgesormovingparts.
Damaged or entangled cords increase the risk of electric
shock.
e. Whenoperatingapowertooloutdoors,useanexten-
sioncordsuitableforoutdooruse. Use of a cord suitable
for outdoor use reduces the risk of electric shock.
f. Ifoperatingapowertoolinadamplocationisunavoid-
able,usearesidualcurrentdevice(RCD)protected
supply.UseofanRCDreducestheriskofelectric
shock. Note: The term “Residual Curent Device (RCD)” can
be replaced by “Ground Fault Circuit Interrupter (GFCI)” or
by “Earth Leakage Circuit Breaker (ELCB)”.
3. PersonalSafety
a. Stayalert,watchwhatyouaredoinganduse
commonsensewhenoperatingapowertool.Donot
useapowertoolwhileyouaretiredorunderthe
inuenceofdrugs,alcoholormedication.A moment
of inattention while operating power tools may result in
serious personal injury.
b. Usepersonalprotectiveequipment.Alwaysweareye
protection.Protective equipment such as dust mask, non-
skid safety shoes, hard hat, or hearing protection used for
appropriate conditions will reduce personal injuries.
c. Preventunintentionalstarting.Ensuretheswitchisin
theoff-positionbeforeconnectingtopowersourceand/
orbatterypack,pickinguporcarryingthetool. Carrying
power tools with your nger on the switch or energising
power tools that have the switch on invites accidents.
d. Removeanyadjustingkeyorwrenchbeforeturningthe
powertoolon. A wrench or a key left attached to a rotating
part of the power tool may result in personal injury.
e. Donotoverreach.Keepproperfootingandbalance
atalltimes.This enables better control of the power tool
in unexpected situations.
f. Dressproperly.Donotwearlooseclothingorjewel-
lery.Keepyourhair,clothingandglovesawayfrom
movingparts. Loose clothes, jewellery or long hair can
be caught in moving parts.

4●ENGLISH
g. Ifdevicesareprovidedfortheconnectionofdust
extractionandcollectionfacilities,ensuretheseare
connectedandproperlyused.Use of these devices
can reduce dust related hazards.
4. PowerToolUseandCare
a. Donotforcethepowertool.Usethecorrectpowertool
foryourapplication.The correct power tool will do the job
better and safer at the rate for which it was designed.
b. Donotusethepowertooliftheswitchdoesnotturn
itonandoff. Any power tool that cannot be controlled
with the switch is dangerous and must be repaired.
c. Disconnecttheplugfromthepowersourceand/or
thebatterypackfromthepowertoolbeforemaking
anyadjustments,changingaccessories,orstoring
powertools. Such preventive safety measures reduce
the risk of starting the power tool accidentally.
d. Storeidlepowertoolsoutofthereachofchildrenand
donotallowpersonsunfamiliarwiththepowertoolor
theseinstructionstooperatethepowertool. Power tools
are dangerous in the hands of untrained users.
e. Maintainpowertools.Checkformisalignmentorbinding
ofmovingparts,breakageofpartsandanyothercondition
thatmayaffectthepowertoolsoperation.Ifdamaged,
havethepowertoolrepairedbeforeuse.Many accidents
are caused by poorly maintained power tools.
f. Keepcuttingtoolssharpandclean. Properly main-
tained cutting tools with sharp cutting edges are less
likely to bind and are easier to control.
5. Service
a. Haveyourpowertoolservicedbyaqualiedrepair
personusingonlyidenticalreplacementparts. This
will ensure that the safety of the power tool is maintained.
ADDITIONALSAFETYINSTRUCTIONS
FORHAMMERDRILL
Wearearprotectorswithimpactdrills.Exposure to
noise can cause hearing loss.
Useauxiliaryhandlessuppliedwiththetool.Loss
of control can cause personal injury.
Holdpowertoolbyinsulatedgrippingsurfaces
whenperforminganoperationwherethecutting
toolmaycontacthiddenwiringoritsowncord.
Contact with a “live” wire will also make exposed metal
parts of the power tool “live” and shock the operator.
Use clamps or another practical way to secure and
support the workpiece to a stable platform. Holding the
work by hand or against your body leaves it unstable
and may lead to loss of control.
 Before drilling into walls, oors or ceilings check for the
location of wiring and pipes.
 Avoid touching the tip of a drill bit just after drilling, as it
may be hot
6. Electricalsafety
Your tool is double insulated; therefore no earth
wire is required. Always check that the main voltage
corresponds to the voltage on the rating plate.
Warning!If the power cord is damaged, it must
be replaced by the manufacturer, authorized
BLACK+DECKER Service Center or an equally
qualied person in order to avoid damage or
injury. If the power cord is replaced by an equally
qualied person, but not authorized by BLACK+-
DECKER, the warranty will not be valid.
7. Labelsontool
The label on your tool may include the following symbols:
Read
Instructions
Manual
Use Eye
Protection
Use Ear
Protection
V ...........Volts
A ...........Amperes
Hz .........Hertz
W ..........Watts
min ........minutes
...............Alternating
Current
...............Direct
Current
n0..........No-Load
Speed
...............Class II
Construction
...............Earthing
Terminal
...............Safety Alert
Symbol
.../min.....Revolutions
or Recipro-
cation per
minute
FEATURES(Fig.A)
1.Variable speed switch
2. Lock-on button
3. Forward/reverse slider
4.Drilling mode selector
5. Chuck
6. Depth stop
7.Side handle
ASSAMBLY
4 • ENGLISH
4 • ENGLISH
making any adjustments, changing accessories,
or storing power tools. Such preventive safety measures
reduce the risk of starting the power tool accidentally.
d. Store idle power tools out of the reach of children
and do not allow persons unfamiliar with the power
tool or these instructions to operate the power
tool. Power tools are dangerous in the hands
of untrained users.
e. Maintain power tools. Check for misalignment
or binding of moving parts, breakage of par ts and
any other condition that may affect the power
tools operation. If damaged, have the power tool
repaired before use. Many accidents are caused by
poorly maintained power tools.
f. Keep cutting tools sharp and clean.Properly
maintained cutting tools with sharp cutting edges are
less likely to bind and are easier to control.
5. Service
a. Have your power tool serviced by a qualified
repair person using only identical replacement
parts. This will ensure that the safety of the power
tool is maintained.
6. Electrical safety
Your tool is double insulated; therefore no earth
wire is required. Always check that the main voltage
corresponds to the voltage on the rating plate.
Warning! If the power cord is damaged, it must
be replaced by the manufacturer, authorized
BLACK+DECKER Service Center or an equally
qualified person in order to avoid damage or
injury. If the power cord is replaced by an equally
7. Labels on tool
The label on your tool may include the following symbols:
FEATURES (Fig. A)
1. Variable speed switch
2. Lock-on button
3. Forward/reverse slider
4. Drilling mode selector
5. Chuck
6. Depth stop
7. Side handle
ADDITIONAL SAFETY INSTRUCTIONS
FOR HAMMER DRILL
fWear ear protectors with impact drills. Exposure to
noise can cause hearing loss.
fUse auxiliary handles supplied with the tool. Loss
of control can cause personal injur y.
fHold power tool by insulated gripping surfaces
when performing an operation where the cutting
tool may contact hidden wiring or its own cord.
Contact with a “live” wire will also make exposed metal
parts of the power tool “live” and shock the operator.
fUse clamps or another practical way to secure
and support the workpiece to a stable platform.
Holding the work by hand or against your body leaves
it unstable and may lead to loss of control.
fBefore drilling into walls, floors or ceilings check for
the location of wiring and pipes.
fAvoid touching the tip of a drill bit just after drilling, as
it may be hot
ASSAMBLY
Warning! Before assembly, make sure that the tool is
switched off and unplugged.
Fitting the side handle and depth stop (Fig. B)
Turn the grip counterclockwise until you can slide the
side handle (7) onto the front of the tool as shown.
fRotate the side handle into the desired position.
fInsert the depth stop (6) into the mounting hole as
shown.
fSet the drilling depth as described below.
fTighten the side handle by turning the grip clockwise.
Fitting a drill bit or screwdriver bit
Keyed chuck (Fig. C)
fOpen the chuck by turning the sleeve (9)
counterclockwise.
fInsert the bit shaft (8) into the chuck.
fInsert the chuck key (10) into each hole (11) in the side
of the chuck and turn clockwise until tight.
Removing and refitting the chuck (Fig. D)
fOpen the chuck as far as possible.
fRemove the chuck retaining screw, located in the
chuck, by turning it clockwise using a screwdriver.
fTighten an Allen key into the chuck and strike it with
a hammer as shown.
fRemove the Allen key.
fRemove the chuck by turning it counterclockwise.
fTo refit the chuck, screw it onto the spindle and secure
it with the chuck retaining screw.
Read
Instructions
Manual
Use Eye
Protection
Use Ear
Protection
V ........ Volts
A ........ Amperes
Hz ....... Hert z
W ........ Watts
min ..... minutes
..... Alternating
Current
..... Direct
Current
n0....... No-Load
Speed
...... Class II
Construction
.... Earthing
Terminal
.... Safety A lert
Symbol
.../min.. Revolut ions
or Recipr o-
cation p er
minute
qualified person, but not authorized by
BLACK+DECKER, the warranty will not be valid.
Warning!Before assembly, make sure that the
tool is switched off and unplugged.
Fittingthesidehandleanddepthstop(Fig.B)
Turn the grip counterclockwise until you can slide the side
handle (7) onto the front of the tool as shown.
Rotate the side handle into the desired position.
Insert the depth stop (6) into the mounting hole as shown.
4 • ENGLISH
4 • ENGLISH
making any adjustments, changing accessories,
or storing power tools. Such preventive safety measures
reduce the risk of starting the power tool accidentally.
d. Store idle power tools out of the reach of children
and do not allow persons unfamiliar with the power
tool or these instructions to operate the power
tool. Power tools are dangerous in the hands
of untrained users.
e. Maintain power tools. Check for misalignment
or binding of moving parts, breakage of parts and
any other condition that may affect the power
tools operation. If damaged, have the power tool
repaired before use. Many accidents are caused by
poorly maintained power tools.
f. Keep cutting tools sharp and clean.Properly
maintained cutting tools with sharp cutting edges are
less likely to bind and are easier to control.
5. Service
a. Have your power tool serviced by a qualified
repair person using only identical replacement
parts. This will ensure that the safety of the power
tool is maintained.
6. Electrical safety
Your tool is double insulated; therefore no earth
wire is required. Always check that the main voltage
corresponds to the voltage on the rating plate.
Warning! If the power cord is damaged, it must
be replaced by the manufacturer, authorized
BLACK+DECKER Service Center or an equally
qualified person in order to avoid damage or
injury. If the power cord is replaced by an equally
7. Labels on tool
The label on your tool may include the following symbols:
FEATURES (Fig. A)
1. Variable speed switch
2. Lock-on button
3. Forward/reverse slider
4. Drilling mode selector
5. Chuck
6. Depth stop
7. Side handle
ADDITIONAL SAFETY INSTRUCTIONS
FOR HAMMER DRILL
fWear ear protectors with impact drills. Exposure to
noise can cause hearing loss.
fUse auxiliary handles supplied with the tool. Loss
of control can cause personal injury.
fHold power tool by insulated gripping surfaces
when performing an operation where the cutting
tool may contact hidden wiring or its own cord.
Contact with a “live” wire will also make exposed metal
parts of the power tool “live” and shock the operator.
fUse clamps or another practical way to secure
and support the workpiece to a stable platform.
Holding the work by hand or against your body leaves
it unstable and may lead to loss of control.
fBefore drilling into walls, floors or ceilings check for
the location of wiring and pipes.
fAvoid touching the tip of a drill bit just after drilling, as
it may be hot
ASSAMBLY
Warning! Before assembly, make sure that the tool is
switched off and unplugged.
Fitting the side handle and depth stop (Fig. B)
Turn the grip counterclockwise until you can slide the
side handle (7) onto the front of the tool as shown.
fRotate the side handle into the desired position.
fInsert the depth stop (6) into the mounting hole as
shown.
fSet the drilling depth as described below.
fTighten the side handle by turning the grip clockwise.
Fitting a drill bit or screwdriver bit
Keyed chuck (Fig. C)
fOpen the chuck by turning the sleeve (9)
counterclockwise.
fInsert the bit shaft (8) into the chuck.
fInsert the chuck key (10) into each hole (11) in the side
of the chuck and turn clockwise until tight.
Removing and refitting the chuck (Fig. D)
fOpen the chuck as far as possible.
fRemove the chuck retaining screw, located in the
chuck, by turning it clockwise using a screwdriver.
fTighten an Allen key into the chuck and strike it with
a hammer as shown.
fRemove the Allen key.
fRemove the chuck by turning it counterclockwise.
fTo refit the chuck, screw it onto the spindle and secure
it with the chuck retaining screw.
Read
Instructions
Manual
Use Eye
Protection
Use Ear
Protection
V ........ Volts
A ........ Amperes
Hz ....... Hertz
W ........ Watts
min ..... minutes
..... Alternating
Current
..... Direct
Current
n0....... No-Load
Speed
...... Class II
Construction
.... Earthing
Terminal
.... Safety Alert
Symbol
.../min.. Revolutions
or Recipro-
cation per
minute
qualified person, but not authorized by
BLACK+DECKER, the warranty will not be valid.
4 • ENGLISH
4 • ENGLISH
making any adjustments, changing accessories,
or storing power tools. Such preventive safety measures
reduce the risk of starting the power tool accidentally.
d. Store idle power tools out of the reach of children
and do not allow persons unfamiliar with the power
tool or these instructions to operate the power
tool. Power tools are dangerous in the hands
of untrained users.
e. Maintain power tools. Check for misalignment
or binding of moving parts, breakage of parts and
any other condition that may affect the power
tools operation. If damaged, have the power tool
repaired before use. Many accidents are caused by
poorly maintained power tools.
f. Keep cutting tools sharp and clean.Properly
maintained cutting tools with sharp cutting edges are
less likely to bind and are easier to control.
5. Service
a. Have your power tool serviced by a qualified
repair person using only identical replacement
parts. This will ensure that the safety of the power
tool is maintained.
6. Electrical safety
Your tool is double insulated; therefore no earth
wire is required. Always check that the main voltage
corresponds to the voltage on the rating plate.
Warning! If the power cord is damaged, it must
be replaced by the manufacturer, authorized
BLACK+DECKER Service Center or an equally
qualified person in order to avoid damage or
injury. If the power cord is replaced by an equally
7. Labels on tool
The label on your tool may include the following symbols:
FEATURES (Fig. A)
1. Variable speed switch
2. Lock-on button
3. Forward/reverse slider
4. Drilling mode selector
5. Chuck
6. Depth stop
7. Side handle
ADDITIONAL SAFETY INSTRUCTIONS
FOR HAMMER DRILL
fWear ear protectors with impact drills. Exposure to
noise can cause hearing loss.
fUse auxiliary handles supplied with the tool. Loss
of control can cause personal injury.
fHold power tool by insulated gripping surfaces
when performing an operation where the cutting
tool may contact hidden wiring or its own cord.
Contact with a “live” wire will also make exposed metal
parts of the power tool “live” and shock the operator.
fUse clamps or another practical way to secure
and support the workpiece to a stable platform.
Holding the work by hand or against your body leaves
it unstable and may lead to loss of control.
fBefore drilling into walls, floors or ceilings check for
the location of wiring and pipes.
fAvoid touching the tip of a drill bit just after drilling, as
it may be hot
ASSAMBLY
Warning! Before assembly, make sure that the tool is
switched off and unplugged.
Fitting the side handle and depth stop (Fig. B)
Turn the grip counterclockwise until you can slide the
side handle (7) onto the front of the tool as shown.
fRotate the side handle into the desired position.
fInsert the depth stop (6) into the mounting hole as
shown.
fSet the drilling depth as described below.
fTighten the side handle by turning the grip clockwise.
Fitting a drill bit or screwdriver bit
Keyed chuck (Fig. C)
fOpen the chuck by turning the sleeve (9)
counterclockwise.
fInsert the bit shaft (8) into the chuck.
fInsert the chuck key (10) into each hole (11) in the side
of the chuck and turn clockwise until tight.
Removing and refitting the chuck (Fig. D)
fOpen the chuck as far as possible.
fRemove the chuck retaining screw, located in the
chuck, by turning it clockwise using a screwdriver.
fTighten an Allen key into the chuck and strike it with
a hammer as shown.
fRemove the Allen key.
fRemove the chuck by turning it counterclockwise.
fTo refit the chuck, screw it onto the spindle and secure
it with the chuck retaining screw.
Read
Instructions
Manual
Use Eye
Protection
Use Ear
Protection
V ........ Volts
A ........ Amperes
Hz ....... Hertz
W ........ Watts
min ..... minutes
..... Alternating
Current
..... Direct
Current
n0....... No-Load
Speed
...... Class II
Construction
.... Earthing
Terminal
.... Safety Alert
Symbol
.../min.. Revolutions
or Recipro-
cation per
minute
qualified person, but not authorized by
BLACK+DECKER, the warranty will not be valid.
4 • ENGLISH
4 • ENGLISH
making any adjustments, changing accessories,
or storing power tools. Such preventive safety measures
reduce the risk of starting the power tool accidentally.
d. Store idle power tools out of the reach of children
and do not allow persons unfamiliar with the power
tool or these instructions to operate the power
tool. Power tools are dangerous in the hands
of untrained users.
e. Maintain power tools. Check for misalignment
or binding of moving parts, breakage of parts and
any other condition that may affect the power
tools operation. If damaged, have the power tool
repaired before use. Many accidents are caused by
poorly maintained power tools.
f. Keep cutting tools sharp and clean.Properly
maintained cutting tools with sharp cutting edges are
less likely to bind and are easier to control.
5. Service
a. Have your power tool serviced by a qualified
repair person using only identical replacement
parts. This will ensure that the safety of the power
tool is maintained.
6. Electrical safety
Your tool is double insulated; therefore no earth
wire is required. Always check that the main voltage
corresponds to the voltage on the rating plate.
Warning! If the power cord is damaged, it must
be replaced by the manufacturer, authorized
BLACK+DECKER Service Center or an equally
qualified person in order to avoid damage or
injury. If the power cord is replaced by an equally
7. Labels on tool
The label on your tool may include the following symbols:
FEATURES (Fig. A)
1. Variable speed switch
2. Lock-on button
3. Forward/reverse slider
4. Drilling mode selector
5. Chuck
6. Depth stop
7. Side handle
ADDITIONAL SAFETY INSTRUCTIONS
FOR HAMMER DRILL
fWear ear protectors with impact drills. Exposure to
noise can cause hearing loss.
fUse auxiliary handles supplied with the tool. Loss
of control can cause personal injury.
fHold power tool by insulated gripping surfaces
when performing an operation where the cutting
tool may contact hidden wiring or its own cord.
Contact with a “live” wire will also make exposed metal
parts of the power tool “live” and shock the operator.
fUse clamps or another practical way to secure
and support the workpiece to a stable platform.
Holding the work by hand or against your body leaves
it unstable and may lead to loss of control.
fBefore drilling into walls, floors or ceilings check for
the location of wiring and pipes.
fAvoid touching the tip of a drill bit just after drilling, as
it may be hot
ASSAMBLY
Warning! Before assembly, make sure that the tool is
switched off and unplugged.
Fitting the side handle and depth stop (Fig. B)
Turn the grip counterclockwise until you can slide the
side handle (7) onto the front of the tool as shown.
fRotate the side handle into the desired position.
fInsert the depth stop (6) into the mounting hole as
shown.
fSet the drilling depth as described below.
fTighten the side handle by turning the grip clockwise.
Fitting a drill bit or screwdriver bit
Keyed chuck (Fig. C)
fOpen the chuck by turning the sleeve (9)
counterclockwise.
fInsert the bit shaft (8) into the chuck.
fInsert the chuck key (10) into each hole (11) in the side
of the chuck and turn clockwise until tight.
Removing and refitting the chuck (Fig. D)
fOpen the chuck as far as possible.
fRemove the chuck retaining screw, located in the
chuck, by turning it clockwise using a screwdriver.
fTighten an Allen key into the chuck and strike it with
a hammer as shown.
fRemove the Allen key.
fRemove the chuck by turning it counterclockwise.
fTo refit the chuck, screw it onto the spindle and secure
it with the chuck retaining screw.
Read
Instructions
Manual
Use Eye
Protection
Use Ear
Protection
V ........ Volts
A ........ Amperes
Hz ....... Hertz
W ........ Watts
min ..... minutes
..... Alternating
Current
..... Direct
Current
n0....... No-Load
Speed
...... Class II
Construction
.... Earthing
Terminal
.... Safety Alert
Symbol
.../min.. Revolutions
or Recipro-
cation per
minute
qualified person, but not authorized by
BLACK+DECKER, the warranty will not be valid.
4 • ENGLISH
4 • ENGLISH
making any adjustments, changing accessories,
or storing power tools. Such preventive safety measures
reduce the risk of starting the power tool accidentally.
d. Store idle power tools out of the reach of children
and do not allow persons unfamiliar with the power
tool or these instructions to operate the power
tool. Power tools are dangerous in the hands
of untrained users.
e. Maintain power tools. Check for misalignment
or binding of moving parts, breakage of parts and
any other condition that may affect the power
tools operation. If damaged, have the power tool
repaired before use. Many accidents are caused by
poorly maintained power tools.
f. Keep cutting tools sharp and clean.Properly
maintained cutting tools with sharp cutting edges are
less likely to bind and are easier to control.
5. Service
a. Have your power tool serviced by a qualified
repair person using only identical replacement
parts. This will ensure that the safety of the power
tool is maintained.
6. Electrical safety
Your tool is double insulated; therefore no earth
wire is required. Always check that the main voltage
corresponds to the voltage on the rating plate.
Warning! If the power cord is damaged, it must
be replaced by the manufacturer, authorized
BLACK+DECKER Service Center or an equally
qualified person in order to avoid damage or
injury. If the power cord is replaced by an equally
7. Labels on tool
The label on your tool may include the following symbols:
FEATURES (Fig. A)
1. Variable speed switch
2. Lock-on button
3. Forward/reverse slider
4. Drilling mode selector
5. Chuck
6. Depth stop
7. Side handle
ADDITIONAL SAFETY INSTRUCTIONS
FOR HAMMER DRILL
fWear ear protectors with impact drills. Exposure to
noise can cause hearing loss.
fUse auxiliary handles supplied with the tool. Loss
of control can cause personal injury.
fHold power tool by insulated gripping surfaces
when performing an operation where the cutting
tool may contact hidden wiring or its own cord.
Contact with a “live” wire will also make exposed metal
parts of the power tool “live” and shock the operator.
fUse clamps or another practical way to secure
and support the workpiece to a stable platform.
Holding the work by hand or against your body leaves
it unstable and may lead to loss of control.
fBefore drilling into walls, floors or ceilings check for
the location of wiring and pipes.
fAvoid touching the tip of a drill bit just after drilling, as
it may be hot
ASSAMBLY
Warning! Before assembly, make sure that the tool is
switched off and unplugged.
Fitting the side handle and depth stop (Fig. B)
Turn the grip counterclockwise until you can slide the
side handle (7) onto the front of the tool as shown.
fRotate the side handle into the desired position.
fInsert the depth stop (6) into the mounting hole as
shown.
fSet the drilling depth as described below.
fTighten the side handle by turning the grip clockwise.
Fitting a drill bit or screwdriver bit
Keyed chuck (Fig. C)
fOpen the chuck by turning the sleeve (9)
counterclockwise.
fInsert the bit shaft (8) into the chuck.
fInsert the chuck key (10) into each hole (11) in the side
of the chuck and turn clockwise until tight.
Removing and refitting the chuck (Fig. D)
fOpen the chuck as far as possible.
fRemove the chuck retaining screw, located in the
chuck, by turning it clockwise using a screwdriver.
fTighten an Allen key into the chuck and strike it with
a hammer as shown.
fRemove the Allen key.
fRemove the chuck by turning it counterclockwise.
fTo refit the chuck, screw it onto the spindle and secure
it with the chuck retaining screw.
Read
Instructions
Manual
Use Eye
Protection
Use Ear
Protection
V ........ Volts
A ........ Amperes
Hz ....... Hertz
W ........ Watts
min ..... minutes
..... Alternating
Current
..... Direct
Current
n0....... No-Load
Speed
...... Class II
Construction
.... Earthing
Terminal
.... Safety Alert
Symbol
.../min.. Revolutions
or Recipro-
cation per
minute
qualified person, but not authorized by
BLACK+DECKER, the warranty will not be valid.
4 • ENGLISH
4 • ENGLISH
making any adjustments, changing accessories,
or storing power tools. Such preventive safety measures
reduce the risk of starting the power tool accidentally.
d. Store idle power tools out of the reach of children
and do not allow persons unfamiliar with the power
tool or these instructions to operate the power
tool. Power tools are dangerous in the hands
of untrained users.
e. Maintain power tools. Check for misalignment
or binding of moving parts, breakage of parts and
any other condition that may affect the power
tools operation. If damaged, have the power tool
repaired before use. Many accidents are caused by
poorly maintained power tools.
f. Keep cutting tools sharp and clean.Properly
maintained cutting tools with sharp cutting edges are
less likely to bind and are easier to control.
5. Service
a. Have your power tool serviced by a qualified
repair person using only identical replacement
parts. This will ensure that the safety of the power
tool is maintained.
6. Electrical safety
Your tool is double insulated; therefore no earth
wire is required. Always check that the main voltage
corresponds to the voltage on the rating plate.
Warning! If the power cord is damaged, it must
be replaced by the manufacturer, authorized
BLACK+DECKER Service Center or an equally
qualified person in order to avoid damage or
injury. If the power cord is replaced by an equally
7. Labels on tool
The label on your tool may include the following symbols:
FEATURES (Fig. A)
1. Variable speed switch
2. Lock-on button
3. Forward/reverse slider
4. Drilling mode selector
5. Chuck
6. Depth stop
7. Side handle
ADDITIONAL SAFETY INSTRUCTIONS
FOR HAMMER DRILL
fWear ear protectors with impact drills. Exposure to
noise can cause hearing loss.
fUse auxiliary handles supplied with the tool. Loss
of control can cause personal injury.
fHold power tool by insulated gripping surfaces
when performing an operation where the cutting
tool may contact hidden wiring or its own cord.
Contact with a “live” wire will also make exposed metal
parts of the power tool “live” and shock the operator.
fUse clamps or another practical way to secure
and support the workpiece to a stable platform.
Holding the work by hand or against your body leaves
it unstable and may lead to loss of control.
fBefore drilling into walls, floors or ceilings check for
the location of wiring and pipes.
fAvoid touching the tip of a drill bit just after drilling, as
it may be hot
ASSAMBLY
Warning! Before assembly, make sure that the tool is
switched off and unplugged.
Fitting the side handle and depth stop (Fig. B)
Turn the grip counterclockwise until you can slide the
side handle (7) onto the front of the tool as shown.
fRotate the side handle into the desired position.
fInsert the depth stop (6) into the mounting hole as
shown.
fSet the drilling depth as described below.
fTighten the side handle by turning the grip clockwise.
Fitting a drill bit or screwdriver bit
Keyed chuck (Fig. C)
fOpen the chuck by turning the sleeve (9)
counterclockwise.
fInsert the bit shaft (8) into the chuck.
fInsert the chuck key (10) into each hole (11) in the side
of the chuck and turn clockwise until tight.
Removing and refitting the chuck (Fig. D)
fOpen the chuck as far as possible.
fRemove the chuck retaining screw, located in the
chuck, by turning it clockwise using a screwdriver.
fTighten an Allen key into the chuck and strike it with
a hammer as shown.
fRemove the Allen key.
fRemove the chuck by turning it counterclockwise.
fTo refit the chuck, screw it onto the spindle and secure
it with the chuck retaining screw.
Read
Instructions
Manual
Use Eye
Protection
Use Ear
Protection
V ........ Volts
A ........ Amperes
Hz ....... Hertz
W ........ Watts
min ..... minutes
..... Alternating
Current
..... Direct
Current
n0....... No-Load
Speed
...... Class II
Construction
.... Earthing
Terminal
.... Safety Alert
Symbol
.../min.. Revolutions
or Recipro-
cation per
minute
qualified person, but not authorized by
BLACK+DECKER, the warranty will not be valid.
4 • ENGLISH
4 • ENGLISH
making any adjustments, changing accessories,
or storing power tools. Such preventive safety measures
reduce the risk of starting the power tool accidentally.
d. Store idle power tools out of the reach of children
and do not allow persons unfamiliar with the power
tool or these instructions to operate the power
tool. Power tools are dangerous in the hands
of untrained users.
e. Maintain power tools. Check for misalignment
or binding of moving parts, breakage of parts and
any other condition that may affect the power
tools operation. If damaged, have the power tool
repaired before use. Many accidents are caused by
poorly maintained power tools.
f. Keep cutting tools sharp and clean.Properly
maintained cutting tools with sharp cutting edges are
less likely to bind and are easier to control.
5. Service
a. Have your power tool serviced by a qualified
repair person using only identical replacement
parts. This will ensure that the safety of the power
tool is maintained.
6. Electrical safety
Your tool is double insulated; therefore no earth
wire is required. Always check that the main voltage
corresponds to the voltage on the rating plate.
Warning! If the power cord is damaged, it must
be replaced by the manufacturer, authorized
BLACK+DECKER Service Center or an equally
qualified person in order to avoid damage or
injury. If the power cord is replaced by an equally
7. Labels on tool
The label on your tool may include the following symbols:
FEATURES (Fig. A)
1. Variable speed switch
2. Lock-on button
3. Forward/reverse slider
4. Drilling mode selector
5. Chuck
6. Depth stop
7. Side handle
ADDITIONAL SAFETY INSTRUCTIONS
FOR HAMMER DRILL
fWear ear protectors with impact drills. Exposure to
noise can cause hearing loss.
fUse auxiliary handles supplied with the tool. Loss
of control can cause personal injury.
fHold power tool by insulated gripping surfaces
when performing an operation where the cutting
tool may contact hidden wiring or its own cord.
Contact with a “live” wire will also make exposed metal
parts of the power tool “live” and shock the operator.
fUse clamps or another practical way to secure
and support the workpiece to a stable platform.
Holding the work by hand or against your body leaves
it unstable and may lead to loss of control.
fBefore drilling into walls, floors or ceilings check for
the location of wiring and pipes.
fAvoid touching the tip of a drill bit just after drilling, as
it may be hot
ASSAMBLY
Warning! Before assembly, make sure that the tool is
switched off and unplugged.
Fitting the side handle and depth stop (Fig. B)
Turn the grip counterclockwise until you can slide the
side handle (7) onto the front of the tool as shown.
fRotate the side handle into the desired position.
fInsert the depth stop (6) into the mounting hole as
shown.
fSet the drilling depth as described below.
fTighten the side handle by turning the grip clockwise.
Fitting a drill bit or screwdriver bit
Keyed chuck (Fig. C)
fOpen the chuck by turning the sleeve (9)
counterclockwise.
fInsert the bit shaft (8) into the chuck.
fInsert the chuck key (10) into each hole (11) in the side
of the chuck and turn clockwise until tight.
Removing and refitting the chuck (Fig. D)
fOpen the chuck as far as possible.
fRemove the chuck retaining screw, located in the
chuck, by turning it clockwise using a screwdriver.
fTighten an Allen key into the chuck and strike it with
a hammer as shown.
fRemove the Allen key.
fRemove the chuck by turning it counterclockwise.
fTo refit the chuck, screw it onto the spindle and secure
it with the chuck retaining screw.
Read
Instructions
Manual
Use Eye
Protection
Use Ear
Protection
V ........ Volts
A ........ Amperes
Hz ....... Hertz
W ........ Watts
min ..... minutes
..... Alternating
Current
..... Direct
Current
n0....... No-Load
Speed
...... Class II
Construction
.... Earthing
Terminal
.... Safety Alert
Symbol
.../min.. Revolutions
or Recipro-
cation per
minute
qualified person, but not authorized by
BLACK+DECKER, the warranty will not be valid.
4 • ENGLISH
4 • ENGLISH
making any adjustments, changing accessories,
or storing power tools. Such preventive safety measures
reduce the risk of starting the power tool accidentally.
d. Store idle power tools out of the reach of children
and do not allow persons unfamiliar with the power
tool or these instructions to operate the power
tool. Power tools are dangerous in the hands
of untrained users.
e. Maintain power tools. Check for misalignment
or binding of moving parts, breakage of parts and
any other condition that may affect the power
tools operation. If damaged, have the power tool
repaired before use. Many accidents are caused by
poorly maintained power tools.
f. Keep cutting tools sharp and clean.Properly
maintained cutting tools with sharp cutting edges are
less likely to bind and are easier to control.
5. Service
a. Have your power tool serviced by a qualified
repair person using only identical replacement
parts. This will ensure that the safety of the power
tool is maintained.
6. Electrical safety
Your tool is double insulated; therefore no earth
wire is required. Always check that the main voltage
corresponds to the voltage on the rating plate.
Warning! If the power cord is damaged, it must
be replaced by the manufacturer, authorized
BLACK+DECKER Service Center or an equally
qualified person in order to avoid damage or
injury. If the power cord is replaced by an equally
7. Labels on tool
The label on your tool may include the following symbols:
FEATURES (Fig. A)
1. Variable speed switch
2. Lock-on button
3. Forward/reverse slider
4. Drilling mode selector
5. Chuck
6. Depth stop
7. Side handle
ADDITIONAL SAFETY INSTRUCTIONS
FOR HAMMER DRILL
fWear ear protectors with impact drills. Exposure to
noise can cause hearing loss.
fUse auxiliary handles supplied with the tool. Loss
of control can cause personal injury.
fHold power tool by insulated gripping surfaces
when performing an operation where the cutting
tool may contact hidden wiring or its own cord.
Contact with a “live” wire will also make exposed metal
parts of the power tool “live” and shock the operator.
fUse clamps or another practical way to secure
and support the workpiece to a stable platform.
Holding the work by hand or against your body leaves
it unstable and may lead to loss of control.
fBefore drilling into walls, floors or ceilings check for
the location of wiring and pipes.
fAvoid touching the tip of a drill bit just after drilling, as
it may be hot
ASSAMBLY
Warning! Before assembly, make sure that the tool is
switched off and unplugged.
Fitting the side handle and depth stop (Fig. B)
Turn the grip counterclockwise until you can slide the
side handle (7) onto the front of the tool as shown.
fRotate the side handle into the desired position.
fInsert the depth stop (6) into the mounting hole as
shown.
fSet the drilling depth as described below.
fTighten the side handle by turning the grip clockwise.
Fitting a drill bit or screwdriver bit
Keyed chuck (Fig. C)
fOpen the chuck by turning the sleeve (9)
counterclockwise.
fInsert the bit shaft (8) into the chuck.
fInsert the chuck key (10) into each hole (11) in the side
of the chuck and turn clockwise until tight.
Removing and refitting the chuck (Fig. D)
fOpen the chuck as far as possible.
fRemove the chuck retaining screw, located in the
chuck, by turning it clockwise using a screwdriver.
fTighten an Allen key into the chuck and strike it with
a hammer as shown.
fRemove the Allen key.
fRemove the chuck by turning it counterclockwise.
fTo refit the chuck, screw it onto the spindle and secure
it with the chuck retaining screw.
Read
Instructions
Manual
Use Eye
Protection
Use Ear
Protection
V ........ Volts
A ........ Amperes
Hz ....... Hertz
W ........ Watts
min ..... minutes
..... Alternating
Current
..... Direct
Current
n0....... No-Load
Speed
...... Class II
Construction
.... Earthing
Terminal
.... Safety Alert
Symbol
.../min.. Revolutions
or Recipro-
cation per
minute
qualified person, but not authorized by
BLACK+DECKER, the warranty will not be valid.
4 • ENGLISH
4 • ENGLISH
making any adjustments, changing accessories,
or storing power tools. Such preventive safety measures
reduce the risk of starting the power tool accidentally.
d. Store idle power tools out of the reach of children
and do not allow persons unfamiliar with the power
tool or these instructions to operate the power
tool. Power tools are dangerous in the hands
of untrained users.
e. Maintain power tools. Check for misalignment
or binding of moving parts, breakage of parts and
any other condition that may affect the power
tools operation. If damaged, have the power tool
repaired before use. Many accidents are caused by
poorly maintained power tools.
f. Keep cutting tools sharp and clean.Properly
maintained cutting tools with sharp cutting edges are
less likely to bind and are easier to control.
5. Service
a. Have your power tool serviced by a qualified
repair person using only identical replacement
parts. This will ensure that the safety of the power
tool is maintained.
6. Electrical safety
Your tool is double insulated; therefore no earth
wire is required. Always check that the main voltage
corresponds to the voltage on the rating plate.
Warning! If the power cord is damaged, it must
be replaced by the manufacturer, authorized
BLACK+DECKER Service Center or an equally
qualified person in order to avoid damage or
injury. If the power cord is replaced by an equally
7. Labels on tool
The label on your tool may include the following symbols:
FEATURES (Fig. A)
1. Variable speed switch
2. Lock-on button
3. Forward/reverse slider
4. Drilling mode selector
5. Chuck
6. Depth stop
7. Side handle
ADDITIONAL SAFETY INSTRUCTIONS
FOR HAMMER DRILL
fWear ear protectors with impact drills. Exposure to
noise can cause hearing loss.
fUse auxiliary handles supplied with the tool. Loss
of control can cause personal injury.
fHold power tool by insulated gripping surfaces
when performing an operation where the cutting
tool may contact hidden wiring or its own cord.
Contact with a “live” wire will also make exposed metal
parts of the power tool “live” and shock the operator.
fUse clamps or another practical way to secure
and support the workpiece to a stable platform.
Holding the work by hand or against your body leaves
it unstable and may lead to loss of control.
fBefore drilling into walls, floors or ceilings check for
the location of wiring and pipes.
fAvoid touching the tip of a drill bit just after drilling, as
it may be hot
ASSAMBLY
Warning! Before assembly, make sure that the tool is
switched off and unplugged.
Fitting the side handle and depth stop (Fig. B)
Turn the grip counterclockwise until you can slide the
side handle (7) onto the front of the tool as shown.
fRotate the side handle into the desired position.
fInsert the depth stop (6) into the mounting hole as
shown.
fSet the drilling depth as described below.
fTighten the side handle by turning the grip clockwise.
Fitting a drill bit or screwdriver bit
Keyed chuck (Fig. C)
fOpen the chuck by turning the sleeve (9)
counterclockwise.
fInsert the bit shaft (8) into the chuck.
fInsert the chuck key (10) into each hole (11) in the side
of the chuck and turn clockwise until tight.
Removing and refitting the chuck (Fig. D)
fOpen the chuck as far as possible.
fRemove the chuck retaining screw, located in the
chuck, by turning it clockwise using a screwdriver.
fTighten an Allen key into the chuck and strike it with
a hammer as shown.
fRemove the Allen key.
fRemove the chuck by turning it counterclockwise.
fTo refit the chuck, screw it onto the spindle and secure
it with the chuck retaining screw.
Read
Instructions
Manual
Use Eye
Protection
Use Ear
Protection
V ........ Volts
A ........ Amperes
Hz ....... Hertz
W ........ Watts
min ..... minutes
..... Alternating
Current
..... Direct
Current
n0....... No-Load
Speed
...... Class II
Construction
.... Earthing
Terminal
.... Safety Alert
Symbol
.../min.. Revolutions
or Recipro-
cation per
minute
qualified person, but not authorized by
BLACK+DECKER, the warranty will not be valid.
4 • ENGLISH
4 • ENGLISH
making any adjustments, changing accessories,
or storing power tools. Such preventive safety measures
reduce the risk of starting the power tool accidentally.
d. Store idle power tools out of the reach of children
and do not allow persons unfamiliar with the power
tool or these instructions to operate the power
tool. Power tools are dangerous in the hands
of untrained users.
e. Maintain power tools. Check for misalignment
or binding of moving parts, breakage of parts and
any other condition that may affect the power
tools operation. If damaged, have the power tool
repaired before use. Many accidents are caused by
poorly maintained power tools.
f. Keep cutting tools sharp and clean.Properly
maintained cutting tools with sharp cutting edges are
less likely to bind and are easier to control.
5. Service
a. Have your power tool serviced by a qualified
repair person using only identical replacement
parts. This will ensure that the safety of the power
tool is maintained.
6. Electrical safety
Your tool is double insulated; therefore no earth
wire is required. Always check that the main voltage
corresponds to the voltage on the rating plate.
Warning! If the power cord is damaged, it must
be replaced by the manufacturer, authorized
BLACK+DECKER Service Center or an equally
qualified person in order to avoid damage or
injury. If the power cord is replaced by an equally
7. Labels on tool
The label on your tool may include the following symbols:
FEATURES (Fig. A)
1. Variable speed switch
2. Lock-on button
3. Forward/reverse slider
4. Drilling mode selector
5. Chuck
6. Depth stop
7. Side handle
ADDITIONAL SAFETY INSTRUCTIONS
FOR HAMMER DRILL
fWear ear protectors with impact drills. Exposure to
noise can cause hearing loss.
fUse auxiliary handles supplied with the tool. Loss
of control can cause personal injury.
fHold power tool by insulated gripping surfaces
when performing an operation where the cutting
tool may contact hidden wiring or its own cord.
Contact with a “live” wire will also make exposed metal
parts of the power tool “live” and shock the operator.
fUse clamps or another practical way to secure
and support the workpiece to a stable platform.
Holding the work by hand or against your body leaves
it unstable and may lead to loss of control.
fBefore drilling into walls, floors or ceilings check for
the location of wiring and pipes.
fAvoid touching the tip of a drill bit just after drilling, as
it may be hot
ASSAMBLY
Warning! Before assembly, make sure that the tool is
switched off and unplugged.
Fitting the side handle and depth stop (Fig. B)
Turn the grip counterclockwise until you can slide the
side handle (7) onto the front of the tool as shown.
fRotate the side handle into the desired position.
fInsert the depth stop (6) into the mounting hole as
shown.
fSet the drilling depth as described below.
fTighten the side handle by turning the grip clockwise.
Fitting a drill bit or screwdriver bit
Keyed chuck (Fig. C)
fOpen the chuck by turning the sleeve (9)
counterclockwise.
fInsert the bit shaft (8) into the chuck.
fInsert the chuck key (10) into each hole (11) in the side
of the chuck and turn clockwise until tight.
Removing and refitting the chuck (Fig. D)
fOpen the chuck as far as possible.
fRemove the chuck retaining screw, located in the
chuck, by turning it clockwise using a screwdriver.
fTighten an Allen key into the chuck and strike it with
a hammer as shown.
fRemove the Allen key.
fRemove the chuck by turning it counterclockwise.
fTo refit the chuck, screw it onto the spindle and secure
it with the chuck retaining screw.
Read
Instructions
Manual
Use Eye
Protection
Use Ear
Protection
V ........ Volts
A ........ Amperes
Hz ....... Hertz
W ........ Watts
min ..... minutes
..... Alternating
Current
..... Direct
Current
n0....... No-Load
Speed
...... Class II
Construction
.... Earthing
Terminal
.... Safety Alert
Symbol
.../min.. Revolutions
or Recipro-
cation per
minute
qualified person, but not authorized by
BLACK+DECKER, the warranty will not be valid.
4 • ENGLISH
4 • ENGLISH
making any adjustments, changing accessories,
or storing power tools. Such preventive safety measures
reduce the risk of starting the power tool accidentally.
d. Store idle power tools out of the reach of children
and do not allow persons unfamiliar with the power
tool or these instructions to operate the power
tool. Power tools are dangerous in the hands
of untrained users.
e. Maintain power tools. Check for misalignment
or binding of moving parts, breakage of parts and
any other condition that may affect the power
tools operation. If damaged, have the power tool
repaired before use. Many accidents are caused by
poorly maintained power tools.
f. Keep cutting tools sharp and clean.Properly
maintained cutting tools with sharp cutting edges are
less likely to bind and are easier to control.
5. Service
a. Have your power tool serviced by a qualified
repair person using only identical replacement
parts. This will ensure that the safety of the power
tool is maintained.
6. Electrical safety
Your tool is double insulated; therefore no earth
wire is required. Always check that the main voltage
corresponds to the voltage on the rating plate.
Warning! If the power cord is damaged, it must
be replaced by the manufacturer, authorized
BLACK+DECKER Service Center or an equally
qualified person in order to avoid damage or
injury. If the power cord is replaced by an equally
7. Labels on tool
The label on your tool may include the following symbols:
FEATURES (Fig. A)
1. Variable speed switch
2. Lock-on button
3. Forward/reverse slider
4. Drilling mode selector
5. Chuck
6. Depth stop
7. Side handle
ADDITIONAL SAFETY INSTRUCTIONS
FOR HAMMER DRILL
fWear ear protectors with impact drills. Exposure to
noise can cause hearing loss.
fUse auxiliary handles supplied with the tool. Loss
of control can cause personal injury.
fHold power tool by insulated gripping surfaces
when performing an operation where the cutting
tool may contact hidden wiring or its own cord.
Contact with a “live” wire will also make exposed metal
parts of the power tool “live” and shock the operator.
fUse clamps or another practical way to secure
and support the workpiece to a stable platform.
Holding the work by hand or against your body leaves
it unstable and may lead to loss of control.
fBefore drilling into walls, floors or ceilings check for
the location of wiring and pipes.
fAvoid touching the tip of a drill bit just after drilling, as
it may be hot
ASSAMBLY
Warning! Before assembly, make sure that the tool is
switched off and unplugged.
Fitting the side handle and depth stop (Fig. B)
Turn the grip counterclockwise until you can slide the
side handle (7) onto the front of the tool as shown.
fRotate the side handle into the desired position.
fInsert the depth stop (6) into the mounting hole as
shown.
fSet the drilling depth as described below.
fTighten the side handle by turning the grip clockwise.
Fitting a drill bit or screwdriver bit
Keyed chuck (Fig. C)
fOpen the chuck by turning the sleeve (9)
counterclockwise.
fInsert the bit shaft (8) into the chuck.
fInsert the chuck key (10) into each hole (11) in the side
of the chuck and turn clockwise until tight.
Removing and refitting the chuck (Fig. D)
fOpen the chuck as far as possible.
fRemove the chuck retaining screw, located in the
chuck, by turning it clockwise using a screwdriver.
fTighten an Allen key into the chuck and strike it with
a hammer as shown.
fRemove the Allen key.
fRemove the chuck by turning it counterclockwise.
fTo refit the chuck, screw it onto the spindle and secure
it with the chuck retaining screw.
Read
Instructions
Manual
Use Eye
Protection
Use Ear
Protection
V ........ Volts
A ........ Amperes
Hz ....... Hertz
W ........ Watts
min ..... minutes
..... Alternating
Current
..... Direct
Current
n0....... No-Load
Speed
...... Class II
Construction
.... Earthing
Terminal
.... Safety Alert
Symbol
.../min.. Revolutions
or Recipro-
cation per
minute
qualified person, but not authorized by
BLACK+DECKER, the warranty will not be valid.

ENGLISH●5
Set the drilling depth as described below.
Tighten the side handle by turning the grip clockwise.
FittingadrillbitorscrewdriverbitKeyed
chuck(Fig.C)
Open the chuck by turning the sleeve (9) counterclockwise.
Insert the bit shaft (8) into the chuck.
Insert the chuck key (10) into each hole (11) in the side
of the chuck and turn clockwise until tight.
Removingandrettingthechuck(Fig.D)
Open the chuck as far as possible.
Remove the chuck retaining screw, located in the
chuck, by turning it clockwise using a screwdriver.
Tighten an Allen key into the chuck and strike it with a
hammer as shown.
Remove the Allen key.
Remove the chuck by turning it counterclockwise.
 To ret the chuck, screw it onto the spindle and secure
it with the chuck retaining screw.
USE
Warning!Let the tool work at its own pace. Do not overload.
Warning!Before drilling into walls, oors or ceilings,
check for the location of wiring and pipes.
Selectingthedirectionofrotation(Fig.E)
For drilling and for tightening screws, use forward (clockwise)
rotation. For loosening screws or removing a jammed drill bit,
use reverse (counterclockwise) rotation.
To select forward rotation, push the forward/reverse
slider (3) to the centre position.
To select reverse rotation, push the forward/reverse
slider to the left.
Warning! Never change the direction of rotation while the
motor is running.
Selectingthedrillingmode
For drilling in masonry, set the drilling mode selector (3)
to the
ENGLISH •5
ENGLISH • 5
USE
Warning! Let the tool work at its own pace. Do not
overload.
Warning! Before drilling into walls, floors or ceilings,
check for the location of wiring and pipes.
Selecting the direction of rotation (Fig. E)
For drilling and for tightening screws, use forward
(clockwise) rotation. For loosening screws or removing a
jammed drill bit, use reverse (counterclockwise) rotation.
fTo select forward rotation, push the forward/reverse
slider (3) to the centre position.
fTo select reverse rotation, push the forward/reverse
slider to the left.
Warning! Never change the direction of rotation while
the motor is running.
Selecting the drilling mode
fFor drilling in masonry, set the drilling mode selector
(3) to the position.
fFor drilling in other materials and for screwdriving, set
the drilling mode selector to the position.
Setting the drilling depth (Fig. F)
fSlacken the side handle (7) by turning the grip
counterclockwise.
fSet the depth stop (6) to the desired position. The
maximum drilling depth is equal to the distance
between the tip of the drill bit and the front end of the
depth stop.
fTighten the side handle by turning the grip clockwise.
Switching on and off
fTo switch the tool on, press the speed switch (1).
For tools with variable speed switch, the tool speed
depends on how far you press the switch. As a
general rule, use low speeds for large diameter
drill bits and high speeds for smaller diameter drill bits.
fFor continuous operation, press the lock-on button (2)
and release the speed switch. This option is available
only at full speed. This option does not work in reverse
rotation. Reverse rotation available only for HD500.
fTo switch the tool off, release the speed switch.
To switch the tool off when in continuous operation,
press the speed switch once more and release it.
MAINTENANCE
Keep guards, air vents and the motor housing as clear as
possible of dust and dirt. Wipe with a clean cloth and blow
through with a low-pressure air supply. Excessive build-up
of metal dust can cause tracking of electrical current from
the internal parts to exposed metal parts.
Important! To assure product SAFETY and RELIABILITY,
repairs, maintenance and adjustment (other than those
listed in this manual) should be performed by authorized
service centers or other qualified service personnel,
always using identical replacement parts.
ACCESSORIES
Recommended accessories for use with your product
are available from your local dealer or authorized service
center.
PROTECTING THE ENVIRONMENT
Separate collection. This product must not be
disposed of with normal household waste.
Should you find one day that your
BLACK+DECKER product needs replacement, or
if it is of no further use to you, do not dispose of it
with household waste. Make this product available
for separate collection.
Separate collection of used products and packaging
allows materials to be recycled and used again.
Re-use of recycled materials helps prevent
environmental pollution and reduces the demand
for raw materials. Local regulations may provide for
separate collection of electrical products from the
household, at municipal waste sites or by the
retailer when you purchase a new product.
SERVICE INFORMATION
BLACK+DECKER offers a full network of company-owned
and authorized service locations throughtout Asia. All
BLACK+DECKER Service Centers are staffed with trained
personnel to provide customers with efficient and reliable
product service.
Whether you need technical advice, repair, or genuine
factory replacement parts, contact the BLACK+DECKER
location nearest to you.
NOTE
fBLACK+DECKER’s policy is one of continuous
improvement to our products and, as such, we reserve
the right to change product specifications without prior
notice.
fStandard equipment and accessories may vary by
country.
fProduct specifications may differ by country.
fComplete product range may not be available in all
countries. Contact your local BLACK+DECKER
dealers for range availability.
position.
For drilling in other materials and for screwdriving, set
the drilling mode selector to the
ENGLISH •5
ENGLISH • 5
USE
Warning! Let the tool work at its own pace. Do not
overload.
Warning! Before drilling into walls, floors or ceilings,
check for the location of wiring and pipes.
Selecting the direction of rotation (Fig. E)
For drilling and for tightening screws, use forward
(clockwise) rotation. For loosening screws or removing a
jammed drill bit, use reverse (counterclockwise) rotation.
fTo select forward rotation, push the forward/reverse
slider (3) to the centre position.
fTo select reverse rotation, push the forward/reverse
slider to the left.
Warning! Never change the direction of rotation while
the motor is running.
Selecting the drilling mode
fFor drilling in masonry, set the drilling mode selector
(3) to the position.
fFor drilling in other materials and for screwdriving, set
the drilling mode selector to the position.
Setting the drilling depth (Fig. F)
fSlacken the side handle (7) by turning the grip
counterclockwise.
fSet the depth stop (6) to the desired position. The
maximum drilling depth is equal to the distance
between the tip of the drill bit and the front end of the
depth stop.
fTighten the side handle by turning the grip clockwise.
Switching on and off
fTo switch the tool on, press the speed switch (1).
For tools with variable speed switch, the tool speed
depends on how far you press the switch. As a
general rule, use low speeds for large diameter
drill bits and high speeds for smaller diameter drill bits.
fFor continuous operation, press the lock-on button (2)
and release the speed switch. This option is available
only at full speed. This option does not work in reverse
rotation. Reverse rotation available only for HD500.
fTo switch the tool off, release the speed switch.
To switch the tool off when in continuous operation,
press the speed switch once more and release it.
MAINTENANCE
Keep guards, air vents and the motor housing as clear as
possible of dust and dirt. Wipe with a clean cloth and blow
through with a low-pressure air supply. Excessive build-up
of metal dust can cause tracking of electrical current from
the internal parts to exposed metal parts.
Important! To assure product SAFETY and RELIABILITY,
repairs, maintenance and adjustment (other than those
listed in this manual) should be performed by authorized
service centers or other qualified service personnel,
always using identical replacement parts.
ACCESSORIES
Recommended accessories for use with your product
are available from your local dealer or authorized service
center.
PROTECTING THE ENVIRONMENT
Separate collection. This product must not be
disposed of with normal household waste.
Should you find one day that your
BLACK+DECKER product needs replacement, or
if it is of no further use to you, do not dispose of it
with household waste. Make this product available
for separate collection.
Separate collection of used products and packaging
allows materials to be recycled and used again.
Re-use of recycled materials helps prevent
environmental pollution and reduces the demand
for raw materials. Local regulations may provide for
separate collection of electrical products from the
household, at municipal waste sites or by the
retailer when you purchase a new product.
SERVICE INFORMATION
BLACK+DECKER offers a full network of company-owned
and authorized service locations throughtout Asia. All
BLACK+DECKER Service Centers are staffed with trained
personnel to provide customers with efficient and reliable
product service.
Whether you need technical advice, repair, or genuine
factory replacement parts, contact the BLACK+DECKER
location nearest to you.
NOTE
fBLACK+DECKER’s policy is one of continuous
improvement to our products and, as such, we reserve
the right to change product specifications without prior
notice.
fStandard equipment and accessories may vary by
country.
fProduct specifications may differ by country.
fComplete product range may not be available in all
countries. Contact your local BLACK+DECKER
dealers for range availability.
position.
Settingthedrillingdepth(Fig.F)
Slacken the side handle (7) by turning the grip counter-
clockwise.
Set the depth stop (6) to the desired position. The maxi-
mum drilling depth is equal to the distance between the tip
ENGLISH •5
ENGLISH • 5
USE
Warning! Let the tool work at its own pace. Do not
overload.
Warning! Before drilling into walls, floors or ceilings,
check for the location of wiring and pipes.
Selecting the direction of rotation (Fig. E)
For drilling and for tightening screws, use forward
(clockwise) rotation. For loosening screws or removing a
jammed drill bit, use reverse (counterclockwise) rotation.
fTo select forward rotation, push the forward/reverse
slider (3) to the centre position.
fTo select reverse rotation, push the forward/reverse
slider to the left.
Warning! Never change the direction of rotation while
the motor is running.
Selecting the drilling mode
fFor drilling in masonry, set the drilling mode selector
(3) to the position.
fFor drilling in other materials and for screwdriving, set
the drilling mode selector to the position.
Setting the drilling depth (Fig. F)
fSlacken the side handle (7) by turning the grip
counterclockwise.
fSet the depth stop (6) to the desired position. The
maximum drilling depth is equal to the distance
between the tip of the drill bit and the front end of the
depth stop.
fTighten the side handle by turning the grip clockwise.
Switching on and off
fTo switch the tool on, press the speed switch (1).
For tools with variable speed switch, the tool speed
depends on how far you press the switch. As a
general rule, use low speeds for large diameter
drill bits and high speeds for smaller diameter drill bits.
fFor continuous operation, press the lock-on button (2)
and release the speed switch. This option is available
only at full speed. This option does not work in reverse
rotation. Reverse rotation available only for HD500.
fTo switch the tool off, release the speed switch.
To switch the tool off when in continuous operation,
press the speed switch once more and release it.
MAINTENANCE
Keep guards, air vents and the motor housing as clear as
possible of dust and dirt. Wipe with a clean cloth and blow
through with a low-pressure air supply. Excessive build-up
of metal dust can cause tracking of electrical current from
the internal parts to exposed metal parts.
Important! To assure product SAFETY and RELIABILITY,
repairs, maintenance and adjustment (other than those
listed in this manual) should be performed by authorized
service centers or other qualified service personnel,
always using identical replacement parts.
ACCESSORIES
Recommended accessories for use with your product
are available from your local dealer or authorized service
center.
PROTECTING THE ENVIRONMENT
Separate collection. This product must not be
disposed of with normal household waste.
Should you find one day that your
BLACK+DECKER product needs replacement, or
if it is of no further use to you, do not dispose of it
with household waste. Make this product available
for separate collection.
Separate collection of used products and packaging
allows materials to be recycled and used again.
Re-use of recycled materials helps prevent
environmental pollution and reduces the demand
for raw materials. Local regulations may provide for
separate collection of electrical products from the
household, at municipal waste sites or by the
retailer when you purchase a new product.
SERVICE INFORMATION
BLACK+DECKER offers a full network of company-owned
and authorized service locations throughtout Asia. All
BLACK+DECKER Service Centers are staffed with trained
personnel to provide customers with efficient and reliable
product service.
Whether you need technical advice, repair, or genuine
factory replacement parts, contact the BLACK+DECKER
location nearest to you.
NOTE
fBLACK+DECKER’s policy is one of continuous
improvement to our products and, as such, we reserve
the right to change product specifications without prior
notice.
fStandard equipment and accessories may vary by
country.
fProduct specifications may differ by country.
fComplete product range may not be available in all
countries. Contact your local BLACK+DECKER
dealers for range availability.
ENGLISH •5
ENGLISH • 5
USE
Warning! Let the tool work at its own pace. Do not
overload.
Warning! Before drilling into walls, floors or ceilings,
check for the location of wiring and pipes.
Selecting the direction of rotation (Fig. E)
For drilling and for tightening screws, use forward
(clockwise) rotation. For loosening screws or removing a
jammed drill bit, use reverse (counterclockwise) rotation.
fTo select forward rotation, push the forward/reverse
slider (3) to the centre position.
fTo select reverse rotation, push the forward/reverse
slider to the left.
Warning! Never change the direction of rotation while
the motor is running.
Selecting the drilling mode
fFor drilling in masonry, set the drilling mode selector
(3) to the position.
fFor drilling in other materials and for screwdriving, set
the drilling mode selector to the position.
Setting the drilling depth (Fig. F)
fSlacken the side handle (7) by turning the grip
counterclockwise.
fSet the depth stop (6) to the desired position. The
maximum drilling depth is equal to the distance
between the tip of the drill bit and the front end of the
depth stop.
fTighten the side handle by turning the grip clockwise.
Switching on and off
fTo switch the tool on, press the speed switch (1).
For tools with variable speed switch, the tool speed
depends on how far you press the switch. As a
general rule, use low speeds for large diameter
drill bits and high speeds for smaller diameter drill bits.
fFor continuous operation, press the lock-on button (2)
and release the speed switch. This option is available
only at full speed. This option does not work in reverse
rotation. Reverse rotation available only for HD500.
fTo switch the tool off, release the speed switch.
To switch the tool off when in continuous operation,
press the speed switch once more and release it.
MAINTENANCE
Keep guards, air vents and the motor housing as clear as
possible of dust and dirt. Wipe with a clean cloth and blow
through with a low-pressure air supply. Excessive build-up
of metal dust can cause tracking of electrical current from
the internal parts to exposed metal parts.
Important! To assure product SAFETY and RELIABILITY,
repairs, maintenance and adjustment (other than those
listed in this manual) should be performed by authorized
service centers or other qualified service personnel,
always using identical replacement parts.
ACCESSORIES
Recommended accessories for use with your product
are available from your local dealer or authorized service
center.
PROTECTING THE ENVIRONMENT
Separate collection. This product must not be
disposed of with normal household waste.
Should you find one day that your
BLACK+DECKER product needs replacement, or
if it is of no further use to you, do not dispose of it
with household waste. Make this product available
for separate collection.
Separate collection of used products and packaging
allows materials to be recycled and used again.
Re-use of recycled materials helps prevent
environmental pollution and reduces the demand
for raw materials. Local regulations may provide for
separate collection of electrical products from the
household, at municipal waste sites or by the
retailer when you purchase a new product.
SERVICE INFORMATION
BLACK+DECKER offers a full network of company-owned
and authorized service locations throughtout Asia. All
BLACK+DECKER Service Centers are staffed with trained
personnel to provide customers with efficient and reliable
product service.
Whether you need technical advice, repair, or genuine
factory replacement parts, contact the BLACK+DECKER
location nearest to you.
NOTE
fBLACK+DECKER’s policy is one of continuous
improvement to our products and, as such, we reserve
the right to change product specifications without prior
notice.
fStandard equipment and accessories may vary by
country.
fProduct specifications may differ by country.
fComplete product range may not be available in all
countries. Contact your local BLACK+DECKER
dealers for range availability.
ENGLISH •5
ENGLISH • 5
USE
Warning! Let the tool work at its own pace. Do not
overload.
Warning! Before drilling into walls, floors or ceilings,
check for the location of wiring and pipes.
Selecting the direction of rotation (Fig. E)
For drilling and for tightening screws, use forward
(clockwise) rotation. For loosening screws or removing a
jammed drill bit, use reverse (counterclockwise) rotation.
fTo select forward rotation, push the forward/reverse
slider (3) to the centre position.
fTo select reverse rotation, push the forward/reverse
slider to the left.
Warning! Never change the direction of rotation while
the motor is running.
Selecting the drilling mode
fFor drilling in masonry, set the drilling mode selector
(3) to the position.
fFor drilling in other materials and for screwdriving, set
the drilling mode selector to the position.
Setting the drilling depth (Fig. F)
fSlacken the side handle (7) by turning the grip
counterclockwise.
fSet the depth stop (6) to the desired position. The
maximum drilling depth is equal to the distance
between the tip of the drill bit and the front end of the
depth stop.
fTighten the side handle by turning the grip clockwise.
Switching on and off
fTo switch the tool on, press the speed switch (1).
For tools with variable speed switch, the tool speed
depends on how far you press the switch. As a
general rule, use low speeds for large diameter
drill bits and high speeds for smaller diameter drill bits.
fFor continuous operation, press the lock-on button (2)
and release the speed switch. This option is available
only at full speed. This option does not work in reverse
rotation. Reverse rotation available only for HD500.
fTo switch the tool off, release the speed switch.
To switch the tool off when in continuous operation,
press the speed switch once more and release it.
MAINTENANCE
Keep guards, air vents and the motor housing as clear as
possible of dust and dirt. Wipe with a clean cloth and blow
through with a low-pressure air supply. Excessive build-up
of metal dust can cause tracking of electrical current from
the internal parts to exposed metal parts.
Important! To assure product SAFETY and RELIABILITY,
repairs, maintenance and adjustment (other than those
listed in this manual) should be performed by authorized
service centers or other qualified service personnel,
always using identical replacement parts.
ACCESSORIES
Recommended accessories for use with your product
are available from your local dealer or authorized service
center.
PROTECTING THE ENVIRONMENT
Separate collection. This product must not be
disposed of with normal household waste.
Should you find one day that your
BLACK+DECKER product needs replacement, or
if it is of no further use to you, do not dispose of it
with household waste. Make this product available
for separate collection.
Separate collection of used products and packaging
allows materials to be recycled and used again.
Re-use of recycled materials helps prevent
environmental pollution and reduces the demand
for raw materials. Local regulations may provide for
separate collection of electrical products from the
household, at municipal waste sites or by the
retailer when you purchase a new product.
SERVICE INFORMATION
BLACK+DECKER offers a full network of company-owned
and authorized service locations throughtout Asia. All
BLACK+DECKER Service Centers are staffed with trained
personnel to provide customers with efficient and reliable
product service.
Whether you need technical advice, repair, or genuine
factory replacement parts, contact the BLACK+DECKER
location nearest to you.
NOTE
fBLACK+DECKER’s policy is one of continuous
improvement to our products and, as such, we reserve
the right to change product specifications without prior
notice.
fStandard equipment and accessories may vary by
country.
fProduct specifications may differ by country.
fComplete product range may not be available in all
countries. Contact your local BLACK+DECKER
dealers for range availability.
of the drill bit and the front end of the depth stop.
Tighten the side handle by turning the grip clockwise.
Switchingonandoff
To switch the tool on, press the speed switch (1).
For tools with variable speed switch, the tool speed
depends on how far you press the switch. As a general
rule, use low speeds for large diameter drill bits and
high speeds for smaller diameter drill bits.
For continuous operation, press the lock-on button (2)
and release the speed switch. This option is available
only at full speed.
To switch the tool off, release the speed switch. To
switch the tool off when in continuous operation, press
the speed switch once more and release it.
MAINTENANCE
Keep guards, air vents and the motor housing as clear as
possible of dust and dirt. Wipe with a clean cloth and blow
through with a low-pressure air supply. Excessive build-up of
metal dust can cause tracking of electrical current from the
internal parts to exposed metal parts.
Important!To assure product SAFETY and RELIABILITY,
repairs, maintenance and adjustment (other than those listed
in this manual) should be performed by authorized service
centers or other qualied service personnel, always using
identical replacement parts.
ACCESSORIES
Recommended accessories for use with your product are
available from your local dealer or authorized service center.
PROTECTINGTHEENVIRONMENT
Separate collection. This product must not be dis-
posed of with normal household waste. Should you
nd one day that your BLACK+DECKER product
needs replacement, or if it is of no further use to
you, do not dispose of it with household waste.
Make this product available for separate collection.
Separate collection of used products and packaging
allows materials to be recycled and used again.
Re-use of recycled materials helps prevent
environmental pollution and reduces the demand
for raw materials. Local regulations may provide
for separate collection of electrical products from
the household, at municipal waste sites or by the
retailer when you purchase a new product.
ENGLISH •5
ENGLISH • 5
USE
Warning! Let the tool work at its own pace. Do not
overload.
Warning! Before drilling into walls, floors or ceilings,
check for the location of wiring and pipes.
Selecting the direction of rotation (Fig. E)
For drilling and for tightening screws, use forward
(clockwise) rotation. For loosening screws or removing a
jammed drill bit, use reverse (counterclockwise) rotation.
fTo select forward rotation, push the forward/reverse
slider (3) to the centre position.
fTo select reverse rotation, push the forward/reverse
slider to the left.
Warning! Never change the direction of rotation while
the motor is running.
Selecting the drilling mode
fFor drilling in masonry, set the drilling mode selector
(3) to the position.
fFor drilling in other materials and for screwdriving, set
the drilling mode selector to the position.
Setting the drilling depth (Fig. F)
fSlacken the side handle (7) by turning the grip
counterclockwise.
fSet the depth stop (6) to the desired position. The
maximum drilling depth is equal to the distance
between the tip of the drill bit and the front end of the
depth stop.
fTighten the side handle by turning the grip clockwise.
Switching on and off
fTo switch the tool on, press the speed switch (1).
For tools with variable speed switch, the tool speed
depends on how far you press the switch. As a
general rule, use low speeds for large diameter
drill bits and high speeds for smaller diameter drill bits.
fFor continuous operation, press the lock-on button (2)
and release the speed switch. This option is available
only at full speed. This option does not work in reverse
rotation. Reverse rotation available only for HD500.
fTo switch the tool off, release the speed switch.
To switch the tool off when in continuous operation,
press the speed switch once more and release it.
MAINTENANCE
Keep guards, air vents and the motor housing as clear as
possible of dust and dirt. Wipe with a clean cloth and blow
through with a low-pressure air supply. Excessive build-up
of metal dust can cause tracking of electrical current from
the internal parts to exposed metal parts.
Important! To assure product SAFETY and RELIABILITY,
repairs, maintenance and adjustment (other than those
listed in this manual) should be performed by authorized
service centers or other qualified service personnel,
always using identical replacement parts.
ACCESSORIES
Recommended accessories for use with your product
are available from your local dealer or authorized service
center.
PROTECTING THE ENVIRONMENT
Separate collection. This product must not be
disposed of with normal household waste.
Should you find one day that your
BLACK+DECKER product needs replacement, or
if it is of no further use to you, do not dispose of it
with household waste. Make this product available
for separate collection.
Separate collection of used products and packaging
allows materials to be recycled and used again.
Re-use of recycled materials helps prevent
environmental pollution and reduces the demand
for raw materials. Local regulations may provide for
separate collection of electrical products from the
household, at municipal waste sites or by the
retailer when you purchase a new product.
SERVICE INFORMATION
BLACK+DECKER offers a full network of company-owned
and authorized service locations throughtout Asia. All
BLACK+DECKER Service Centers are staffed with trained
personnel to provide customers with efficient and reliable
product service.
Whether you need technical advice, repair, or genuine
factory replacement parts, contact the BLACK+DECKER
location nearest to you.
NOTE
fBLACK+DECKER’s policy is one of continuous
improvement to our products and, as such, we reserve
the right to change product specifications without prior
notice.
fStandard equipment and accessories may vary by
country.
fProduct specifications may differ by country.
fComplete product range may not be available in all
countries. Contact your local BLACK+DECKER
dealers for range availability.
ENGLISH •5
ENGLISH • 5
USE
Warning! Let the tool work at its own pace. Do not
overload.
Warning! Before drilling into walls, floors or ceilings,
check for the location of wiring and pipes.
Selecting the direction of rotation (Fig. E)
For drilling and for tightening screws, use forward
(clockwise) rotation. For loosening screws or removing a
jammed drill bit, use reverse (counterclockwise) rotation.
fTo select forward rotation, push the forward/reverse
slider (3) to the centre position.
fTo select reverse rotation, push the forward/reverse
slider to the left.
Warning! Never change the direction of rotation while
the motor is running.
Selecting the drilling mode
fFor drilling in masonry, set the drilling mode selector
(3) to the position.
fFor drilling in other materials and for screwdriving, set
the drilling mode selector to the position.
Setting the drilling depth (Fig. F)
fSlacken the side handle (7) by turning the grip
counterclockwise.
fSet the depth stop (6) to the desired position. The
maximum drilling depth is equal to the distance
between the tip of the drill bit and the front end of the
depth stop.
fTighten the side handle by turning the grip clockwise.
Switching on and off
fTo switch the tool on, press the speed switch (1).
For tools with variable speed switch, the tool speed
depends on how far you press the switch. As a
general rule, use low speeds for large diameter
drill bits and high speeds for smaller diameter drill bits.
fFor continuous operation, press the lock-on button (2)
and release the speed switch. This option is available
only at full speed. This option does not work in reverse
rotation. Reverse rotation available only for HD500.
fTo switch the tool off, release the speed switch.
To switch the tool off when in continuous operation,
press the speed switch once more and release it.
MAINTENANCE
Keep guards, air vents and the motor housing as clear as
possible of dust and dirt. Wipe with a clean cloth and blow
through with a low-pressure air supply. Excessive build-up
of metal dust can cause tracking of electrical current from
the internal parts to exposed metal parts.
Important! To assure product SAFETY and RELIABILITY,
repairs, maintenance and adjustment (other than those
listed in this manual) should be performed by authorized
service centers or other qualified service personnel,
always using identical replacement parts.
ACCESSORIES
Recommended accessories for use with your product
are available from your local dealer or authorized service
center.
PROTECTING THE ENVIRONMENT
Separate collection. This product must not be
disposed of with normal household waste.
Should you find one day that your
BLACK+DECKER product needs replacement, or
if it is of no further use to you, do not dispose of it
with household waste. Make this product available
for separate collection.
Separate collection of used products and packaging
allows materials to be recycled and used again.
Re-use of recycled materials helps prevent
environmental pollution and reduces the demand
for raw materials. Local regulations may provide for
separate collection of electrical products from the
household, at municipal waste sites or by the
retailer when you purchase a new product.
SERVICE INFORMATION
BLACK+DECKER offers a full network of company-owned
and authorized service locations throughtout Asia. All
BLACK+DECKER Service Centers are staffed with trained
personnel to provide customers with efficient and reliable
product service.
Whether you need technical advice, repair, or genuine
factory replacement parts, contact the BLACK+DECKER
location nearest to you.
NOTE
fBLACK+DECKER’s policy is one of continuous
improvement to our products and, as such, we reserve
the right to change product specifications without prior
notice.
fStandard equipment and accessories may vary by
country.
fProduct specifications may differ by country.
fComplete product range may not be available in all
countries. Contact your local BLACK+DECKER
dealers for range availability.
ENGLISH •5
ENGLISH • 5
USE
Warning! Let the tool work at its own pace. Do not
overload.
Warning! Before drilling into walls, floors or ceilings,
check for the location of wiring and pipes.
Selecting the direction of rotation (Fig. E)
For drilling and for tightening screws, use forward
(clockwise) rotation. For loosening screws or removing a
jammed drill bit, use reverse (counterclockwise) rotation.
fTo select forward rotation, push the forward/reverse
slider (3) to the centre position.
fTo select reverse rotation, push the forward/reverse
slider to the left.
Warning! Never change the direction of rotation while
the motor is running.
Selecting the drilling mode
fFor drilling in masonry, set the drilling mode selector
(3) to the position.
fFor drilling in other materials and for screwdriving, set
the drilling mode selector to the position.
Setting the drilling depth (Fig. F)
fSlacken the side handle (7) by turning the grip
counterclockwise.
fSet the depth stop (6) to the desired position. The
maximum drilling depth is equal to the distance
between the tip of the drill bit and the front end of the
depth stop.
fTighten the side handle by turning the grip clockwise.
Switching on and off
fTo switch the tool on, press the speed switch (1).
For tools with variable speed switch, the tool speed
depends on how far you press the switch. As a
general rule, use low speeds for large diameter
drill bits and high speeds for smaller diameter drill bits.
fFor continuous operation, press the lock-on button (2)
and release the speed switch. This option is available
only at full speed. This option does not work in reverse
rotation. Reverse rotation available only for HD500.
fTo switch the tool off, release the speed switch.
To switch the tool off when in continuous operation,
press the speed switch once more and release it.
MAINTENANCE
Keep guards, air vents and the motor housing as clear as
possible of dust and dirt. Wipe with a clean cloth and blow
through with a low-pressure air supply. Excessive build-up
of metal dust can cause tracking of electrical current from
the internal parts to exposed metal parts.
Important! To assure product SAFETY and RELIABILITY,
repairs, maintenance and adjustment (other than those
listed in this manual) should be performed by authorized
service centers or other qualified service personnel,
always using identical replacement parts.
ACCESSORIES
Recommended accessories for use with your product
are available from your local dealer or authorized service
center.
PROTECTING THE ENVIRONMENT
Separate collection. This product must not be
disposed of with normal household waste.
Should you find one day that your
BLACK+DECKER product needs replacement, or
if it is of no further use to you, do not dispose of it
with household waste. Make this product available
for separate collection.
Separate collection of used products and packaging
allows materials to be recycled and used again.
Re-use of recycled materials helps prevent
environmental pollution and reduces the demand
for raw materials. Local regulations may provide for
separate collection of electrical products from the
household, at municipal waste sites or by the
retailer when you purchase a new product.
SERVICE INFORMATION
BLACK+DECKER offers a full network of company-owned
and authorized service locations throughtout Asia. All
BLACK+DECKER Service Centers are staffed with trained
personnel to provide customers with efficient and reliable
product service.
Whether you need technical advice, repair, or genuine
factory replacement parts, contact the BLACK+DECKER
location nearest to you.
NOTE
fBLACK+DECKER’s policy is one of continuous
improvement to our products and, as such, we reserve
the right to change product specifications without prior
notice.
fStandard equipment and accessories may vary by
country.
fProduct specifications may differ by country.
fComplete product range may not be available in all
countries. Contact your local BLACK+DECKER
dealers for range availability.

6●ENGLISH
SERVICEINFORMATION
BLACK+DECKER offers a full network of company-owned
and authorized service locations throughtout Asia. All
BLACK+DECKER Service Centers are staffed with trained
personnel to provide customers with efcient and reliable
product service.
Whether you need technical advice, repair, or genuine facto-
ry replacement parts, contact the BLACK+DECKER location
nearest to you.
NOTE
BLACK+DECKER’s policy is one of continuous improve-
ment to our products and, as such, we reserve the right to
change product specications without prior notice.
Standard equipment and accessories may vary by
country.
 Product specications may differ by country.
Complete product range may not be available in all
countries. Contact your local BLACK+DECKER dealers
for range availability.

简体中文●7
HD555/HD555K/HD565K
冲击电钻
技术参数
功率 W 550
电压 伏/赫兹 220/50
额定空载转速 转/分 0-2800
每分钟冲击数 冲击/分 0-45000
最大钻孔能力
钢材 mm 13
混凝土 mm 13
木材 mm 20
一般电动工具安全规则
警告！阅读并理解所有指示说明。如不遵守以
下任何指示，可能导致触电、火灾和 / 或严重人身
伤害。
电动工具通用安全警告
警告！阅读所有警告和所有说明。不遵
照以下警告和说明会导致电击、着火和
／或严重伤害。
保存所有警告和说明书以备查阅。
在所有下列的警告中术语“电动工具”指市电驱动
（有线）电动工具或电池驱动（无线）电动工具。
a) 工作场地的安全
1) 保持工作场地清洁和明亮。混乱和黑暗的场地
会引发事故。
2) 不要在易爆环境，如有易燃液体、气体或粉尘
的环境下操作电动工具。电动工具产生的火
花会点燃粉尘或气体。
3) 让儿童和旁观者离开后操作电动工具。注意力
不集中会使你失去对工具的控制。
b) 电气安全
1) 电动工具插头必须与插座相配。绝不能以任何
方式改装插头。需接地的电动工具不能使用
任何转换插头。未经改装的插头和相配的插
座将减少电击危险。
2) 避免人体接触接地表面，如管道、散热片和冰
箱。如果你身体接地会增加电击危险。
ENGLISH •5
ENGLISH • 5
USE
Warning! Let the tool work at its own pace. Do not
overload.
Warning! Before drilling into walls, floors or ceilings,
check for the location of wiring and pipes.
Selecting the direction of rotation (Fig. E)
For drilling and for tightening screws, use forward
(clockwise) rotation. For loosening screws or removing a
jammed drill bit, use reverse (counterclockwise) rotation.
fTo select forward rotation, push the forward/reverse
slider (3) to the centre position.
fTo select reverse rotation, push the forward/reverse
slider to the left.
Warning! Never change the direction of rotation while
the motor is running.
Selecting the drilling mode
fFor drilling in masonry, set the drilling mode selector
(3) to the position.
fFor drilling in other materials and for screwdriving, set
the drilling mode selector to the position.
Setting the drilling depth (Fig. F)
fSlacken the side handle (7) by turning the grip
counterclockwise.
fSet the depth stop (6) to the desired position. The
maximum drilling depth is equal to the distance
between the tip of the drill bit and the front end of the
depth stop.
fTighten the side handle by turning the grip clockwise.
Switching on and off
fTo switch the tool on, press the speed switch (1).
For tools with variable speed switch, the tool speed
depends on how far you press the switch. As a
general rule, use low speeds for large diameter
drill bits and high speeds for smaller diameter drill bits.
fFor continuous operation, press the lock-on button (2)
and release the speed switch. This option is available
only at full speed. This option does not work in reverse
rotation. Reverse rotation available only for HD500.
fTo switch the tool off, release the speed switch.
To switch the tool off when in continuous operation,
press the speed switch once more and release it.
MAINTENANCE
Keep guards, air vents and the motor housing as clear as
possible of dust and dirt. Wipe with a clean cloth and blow
through with a low-pressure air supply. Excessive build-up
of metal dust can cause tracking of electrical current from
the internal parts to exposed metal parts.
Important! To assure product SAFETY and RELIABILITY,
repairs, maintenance and adjustment (other than those
listed in this manual) should be performed by authorized
service centers or other qualified service personnel,
always using identical replacement parts.
ACCESSORIES
Recommended accessories for use with your product
are available from your local dealer or authorized service
center.
PROTECTING THE ENVIRONMENT
Separate collection. This product must not be
disposed of with normal household waste.
Should you find one day that your
BLACK+DECKER product needs replacement, or
if it is of no further use to you, do not dispose of it
with household waste. Make this product available
for separate collection.
Separate collection of used products and packaging
allows materials to be recycled and used again.
Re-use of recycled materials helps prevent
environmental pollution and reduces the demand
for raw materials. Local regulations may provide for
separate collection of electrical products from the
household, at municipal waste sites or by the
retailer when you purchase a new product.
SERVICE INFORMATION
BLACK+DECKER offers a full network of company-owned
and authorized service locations throughtout Asia. All
BLACK+DECKER Service Centers are staffed with trained
personnel to provide customers with efficient and reliable
product service.
Whether you need technical advice, repair, or genuine
factory replacement parts, contact the BLACK+DECKER
location nearest to you.
NOTE
fBLACK+DECKER’s policy is one of continuous
improvement to our products and, as such, we reserve
the right to change product specifications without prior
notice.
fStandard equipment and accessories may vary by
country.
fProduct specifications may differ by country.
fComplete product range may not be available in all
countries. Contact your local BLACK+DECKER
dealers for range availability.
ENGLISH •5
ENGLISH • 5
USE
Warning! Let the tool work at its own pace. Do not
overload.
Warning! Before drilling into walls, floors or ceilings,
check for the location of wiring and pipes.
Selecting the direction of rotation (Fig. E)
For drilling and for tightening screws, use forward
(clockwise) rotation. For loosening screws or removing a
jammed drill bit, use reverse (counterclockwise) rotation.
fTo select forward rotation, push the forward/reverse
slider (3) to the centre position.
fTo select reverse rotation, push the forward/reverse
slider to the left.
Warning! Never change the direction of rotation while
the motor is running.
Selecting the drilling mode
fFor drilling in masonry, set the drilling mode selector
(3) to the position.
fFor drilling in other materials and for screwdriving, set
the drilling mode selector to the position.
Setting the drilling depth (Fig. F)
fSlacken the side handle (7) by turning the grip
counterclockwise.
fSet the depth stop (6) to the desired position. The
maximum drilling depth is equal to the distance
between the tip of the drill bit and the front end of the
depth stop.
fTighten the side handle by turning the grip clockwise.
Switching on and off
fTo switch the tool on, press the speed switch (1).
For tools with variable speed switch, the tool speed
depends on how far you press the switch. As a
general rule, use low speeds for large diameter
drill bits and high speeds for smaller diameter drill bits.
fFor continuous operation, press the lock-on button (2)
and release the speed switch. This option is available
only at full speed. This option does not work in reverse
rotation. Reverse rotation available only for HD500.
fTo switch the tool off, release the speed switch.
To switch the tool off when in continuous operation,
press the speed switch once more and release it.
MAINTENANCE
Keep guards, air vents and the motor housing as clear as
possible of dust and dirt. Wipe with a clean cloth and blow
through with a low-pressure air supply. Excessive build-up
of metal dust can cause tracking of electrical current from
the internal parts to exposed metal parts.
Important! To assure product SAFETY and RELIABILITY,
repairs, maintenance and adjustment (other than those
listed in this manual) should be performed by authorized
service centers or other qualified service personnel,
always using identical replacement parts.
ACCESSORIES
Recommended accessories for use with your product
are available from your local dealer or authorized service
center.
PROTECTING THE ENVIRONMENT
Separate collection. This product must not be
disposed of with normal household waste.
Should you find one day that your
BLACK+DECKER product needs replacement, or
if it is of no further use to you, do not dispose of it
with household waste. Make this product available
for separate collection.
Separate collection of used products and packaging
allows materials to be recycled and used again.
Re-use of recycled materials helps prevent
environmental pollution and reduces the demand
for raw materials. Local regulations may provide for
separate collection of electrical products from the
household, at municipal waste sites or by the
retailer when you purchase a new product.
SERVICE INFORMATION
BLACK+DECKER offers a full network of company-owned
and authorized service locations throughtout Asia. All
BLACK+DECKER Service Centers are staffed with trained
personnel to provide customers with efficient and reliable
product service.
Whether you need technical advice, repair, or genuine
factory replacement parts, contact the BLACK+DECKER
location nearest to you.
NOTE
fBLACK+DECKER’s policy is one of continuous
improvement to our products and, as such, we reserve
the right to change product specifications without prior
notice.
fStandard equipment and accessories may vary by
country.
fProduct specifications may differ by country.
fComplete product range may not be available in all
countries. Contact your local BLACK+DECKER
dealers for range availability.
4 • ENGLISH
4 • ENGLISH
making any adjustments, changing accessories,
or storing power tools. Such preventive safety measures
reduce the risk of starting the power tool accidentally.
d. Store idle power tools out of the reach of children
and do not allow persons unfamiliar with the power
tool or these instructions to operate the power
tool. Power tools are dangerous in the hands
of untrained users.
e. Maintain power tools. Check for misalignment
or binding of moving parts, breakage of parts and
any other condition that may affect the power
tools operation. If damaged, have the power tool
repaired before use. Many accidents are caused by
poorly maintained power tools.
f. Keep cutting tools sharp and clean.Properly
maintained cutting tools with sharp cutting edges are
less likely to bind and are easier to control.
5. Service
a. Have your power tool serviced by a qualified
repair person using only identical replacement
parts. This will ensure that the safety of the power
tool is maintained.
6. Electrical safety
Your tool is double insulated; therefore no earth
wire is required. Always check that the main voltage
corresponds to the voltage on the rating plate.
Warning! If the power cord is damaged, it must
be replaced by the manufacturer, authorized
BLACK+DECKER Service Center or an equally
qualified person in order to avoid damage or
injury. If the power cord is replaced by an equally
7. Labels on tool
The label on your tool may include the following symbols:
FEATURES (Fig. A)
1. Variable speed switch
2. Lock-on button
3. Forward/reverse slider
4. Drilling mode selector
5. Chuck
6. Depth stop
7. Side handle
ADDITIONAL SAFETY INSTRUCTIONS
FOR HAMMER DRILL
fWear ear protectors with impact drills. Exposure to
noise can cause hearing loss.
fUse auxiliary handles supplied with the tool. Loss
of control can cause personal injury.
fHold power tool by insulated gripping surfaces
when performing an operation where the cutting
tool may contact hidden wiring or its own cord.
Contact with a “live” wire will also make exposed metal
parts of the power tool “live” and shock the operator.
fUse clamps or another practical way to secure
and support the workpiece to a stable platform.
Holding the work by hand or against your body leaves
it unstable and may lead to loss of control.
fBefore drilling into walls, floors or ceilings check for
the location of wiring and pipes.
fAvoid touching the tip of a drill bit just after drilling, as
it may be hot
ASSAMBLY
Warning! Before assembly, make sure that the tool is
switched off and unplugged.
Fitting the side handle and depth stop (Fig. B)
Turn the grip counterclockwise until you can slide the
side handle (7) onto the front of the tool as shown.
fRotate the side handle into the desired position.
fInsert the depth stop (6) into the mounting hole as
shown.
fSet the drilling depth as described below.
fTighten the side handle by turning the grip clockwise.
Fitting a drill bit or screwdriver bit
Keyed chuck (Fig. C)
fOpen the chuck by turning the sleeve (9)
counterclockwise.
fInsert the bit shaft (8) into the chuck.
fInsert the chuck key (10) into each hole (11) in the side
of the chuck and turn clockwise until tight.
Removing and refitting the chuck (Fig. D)
fOpen the chuck as far as possible.
fRemove the chuck retaining screw, located in the
chuck, by turning it clockwise using a screwdriver.
fTighten an Allen key into the chuck and strike it with
a hammer as shown.
fRemove the Allen key.
fRemove the chuck by turning it counterclockwise.
fTo refit the chuck, screw it onto the spindle and secure
it with the chuck retaining screw.
Read
Instructions
Manual
Use Eye
Protection
Use Ear
Protection
V ........ Volts
A ........ Amperes
Hz ....... Hertz
W ........ Watts
min ..... minutes
..... Alternating
Current
..... Direct
Current
n0....... No-Load
Speed
...... Class II
Construction
.... Earthing
Terminal
.... Safety Alert
Symbol
.../min.. Revolutions
or Recipro-
cation per
minute
qualified person, but not authorized by
BLACK+DECKER, the warranty will not be valid.
3) 不得将电动工具暴露在雨中或潮湿环境中。水
进入电动工具将增加电击危险。
4) 不得滥用电线。绝不能用电线搬运、拉动电动
工具或拔出其插头。使电线远离热源、油、锐
边或运动部件。受损或缠绕的软线会增加电击
危险。
5) 当在户外使用电动工具时，使用适合户外使用
的外接软线。适合户外使用的软线将减少电击
危险。
6) 如果在潮湿环境下操作电动工具是不可避免
的，应使用剩余电流动作保护器（RCD）。 使
用RCD 可减小电击危险。
c) 人身安全
1) 保持警觉，当操作电动工具时关注所从事的操
作并保持清醒。当你感到疲倦，或在有药物、
酒精或治疗反应时，不要操作电动工具。在操
作电动工具时瞬间的疏忽会导致严重人身伤
害。
2) 使用个人防护装置。始终佩戴护目镜。安全装
置，诸如适当条件下使用防尘面具、防滑安全
鞋、安全帽、听力防护等装置能减少人身伤害。
3) 防止意外起动。确保开关在连接电源和 / 或电
池盒、拿起或搬运工具时处于关断位置。手指
放在已接通电源的开关上或开关处于接通时
插入插头可能会导致危险。
4) 在电动工具接通之前，拿掉所有调节钥匙或扳
手。遗留在电动工具旋转零件上的扳手或钥匙
会导致人身伤害。
5) 手不要伸展得太长。时刻注意立足点和身体平
衡。这样在意外情况下能很好地控制电动工
具。
6) 着装适当。不要穿宽松衣服或佩戴饰品。让你
的衣服、手套和头发远离运动部件。宽松衣服、
佩饰或长发可能会卷入运动部件中。
7) 如果提供了与排屑、集尘设备连接用的装置，
要确保他们连接完好且使用得当。使用这些装
置可减少尘屑引起的危险。
d) 电动工具使用和注意事项
1) 不要滥用电动工具，根据用途使用适当的电动
工具。选用适当设计的电动工具会使你工作更
有效、更安全。
2) 如果开关不能接通或关断工具电源，则不能使
用该电动工具。不能用开关来控制的电动工具
是危险的且必须进行修理。
3) 在进行任何调节、更换附件或贮存电动工具之
前，必须从电源上拔掉插头和／或使电池盒与
工具脱开。这种防护性措施将减少工具意外起
动的危险。

8●简体中文
4) 将闲置不用的电动工具贮存在儿童所及范围之
外，并且不要让不熟悉电动工具或对这些说明
不了解的人操作电动工具。电动工具在未经培
训的用户手中是危险的。
5) 保养电动工具。检查运动件是否调整到位或卡
住，检查零件破损情况和影响电动工具运行的
其他状况。如有损坏，电动工具应在使用前修
理好。许多事故由维护不良的电动工具引发。
6) 保持切削刀具锋利和清洁。保养良好的有锋利
切削刃的刀具不易卡住而且容易控制。
7) 按照使用说明书，考虑作业条件和进行的作业
来使用电动工具、附件和工具的刀头等。将电
动工具用于那些与其用途不符的操作可能会
导致危险。
e)维修
1)将你的电动工具送交专业维修人员，使用同样
的备件进行修理。这样将确保所维修的电动工
具的安全性。
电钻专用警告语 ：
← 使用冲击电钻时要戴好耳罩。暴露在噪声中会
引起听力损伤。
← 使用随工具提供的辅助手柄。操作失手会引起
人身伤害。
← 当在钻削附件可能触及暗线或其自身软线之
处进行操作时，要通过绝缘握持面来握持工
具。钻削附件碰到带电导线会使工具外露的金
属零件带电从而使操作者受到电击。
← 请使用夹具或采取其它可行方法，将工件可靠
地固定在稳定的平台上。手持或用身体顶住工
件都是不稳定的，会导致操作失控。
← 在墙上、地板或天花板上钻孔之前，请检查电
线和钢管位置。
← 不要在钻孔后立刻碰触可能还带热的钻头尖端。
6. 电气安全
本工具采用双重绝缘，因此无需接地线。
请务必检查电源电压是否与铭牌一致。
警告！如电源线损坏，必须由制造商、
BLACK+DECKER授权服务中心或具备同
等资格的人士进行更换，以避免事故或
人身伤亡。如电源线由具备同等资格但
未经BLACK+DECKER授权的人士更换，
则产品质保将无效。
7. 工具上的标签
 您的工具上可能包含下列符号 ：
4 • ENGLISH
4 • ENGLISH
making any adjustments, changing accessories,
or storing power tools. Such preventive safety measures
reduce the risk of starting the power tool accidentally.
d. Store idle power tools out of the reach of children
and do not allow persons unfamiliar with the power
tool or these instructions to operate the power
tool. Power tools are dangerous in the hands
of untrained users.
e. Maintain power tools. Check for misalignment
or binding of moving parts, breakage of parts and
any other condition that may affect the power
tools operation. If damaged, have the power tool
repaired before use. Many accidents are caused by
poorly maintained power tools.
f. Keep cutting tools sharp and clean.Properly
maintained cutting tools with sharp cutting edges are
less likely to bind and are easier to control.
5. Service
a. Have your power tool serviced by a qualified
repair person using only identical replacement
parts. This will ensure that the safety of the power
tool is maintained.
6. Electrical safety
Your tool is double insulated; therefore no earth
wire is required. Always check that the main voltage
corresponds to the voltage on the rating plate.
Warning! If the power cord is damaged, it must
be replaced by the manufacturer, authorized
BLACK+DECKER Service Center or an equally
qualified person in order to avoid damage or
injury. If the power cord is replaced by an equally
7. Labels on tool
The label on your tool may include the following symbols:
FEATURES (Fig. A)
1. Variable speed switch
2. Lock-on button
3. Forward/reverse slider
4. Drilling mode selector
5. Chuck
6. Depth stop
7. Side handle
ADDITIONAL SAFETY INSTRUCTIONS
FOR HAMMER DRILL
fWear ear protectors with impact drills. Exposure to
noise can cause hearing loss.
fUse auxiliary handles supplied with the tool. Loss
of control can cause personal injury.
fHold power tool by insulated gripping surfaces
when performing an operation where the cutting
tool may contact hidden wiring or its own cord.
Contact with a “live” wire will also make exposed metal
parts of the power tool “live” and shock the operator.
fUse clamps or another practical way to secure
and support the workpiece to a stable platform.
Holding the work by hand or against your body leaves
it unstable and may lead to loss of control.
fBefore drilling into walls, floors or ceilings check for
the location of wiring and pipes.
fAvoid touching the tip of a drill bit just after drilling, as
it may be hot
ASSAMBLY
Warning! Before assembly, make sure that the tool is
switched off and unplugged.
Fitting the side handle and depth stop (Fig. B)
Turn the grip counterclockwise until you can slide the
side handle (7) onto the front of the tool as shown.
fRotate the side handle into the desired position.
fInsert the depth stop (6) into the mounting hole as
shown.
fSet the drilling depth as described below.
fTighten the side handle by turning the grip clockwise.
Fitting a drill bit or screwdriver bit
Keyed chuck (Fig. C)
fOpen the chuck by turning the sleeve (9)
counterclockwise.
fInsert the bit shaft (8) into the chuck.
fInsert the chuck key (10) into each hole (11) in the side
of the chuck and turn clockwise until tight.
Removing and refitting the chuck (Fig. D)
fOpen the chuck as far as possible.
fRemove the chuck retaining screw, located in the
chuck, by turning it clockwise using a screwdriver.
fTighten an Allen key into the chuck and strike it with
a hammer as shown.
fRemove the Allen key.
fRemove the chuck by turning it counterclockwise.
fTo refit the chuck, screw it onto the spindle and secure
it with the chuck retaining screw.
Read
Instructions
Manual
Use Eye
Protection
Use Ear
Protection
V ........ Volts
A ........ Amperes
Hz ....... Hertz
W ........ Watts
min ..... minutes
..... Alternating
Current
..... Direct
Current
n0....... No-Load
Speed
...... Class II
Construction
.... Earthing
Terminal
.... Safety Alert
Symbol
.../min.. Revolutions
or Recipro-
cation per
minute
qualified person, but not authorized by
BLACK+DECKER, the warranty will not be valid.
4 • ENGLISH
4 • ENGLISH
making any adjustments, changing accessories,
or storing power tools. Such preventive safety measures
reduce the risk of starting the power tool accidentally.
d. Store idle power tools out of the reach of children
and do not allow persons unfamiliar with the power
tool or these instructions to operate the power
tool. Power tools are dangerous in the hands
of untrained users.
e. Maintain power tools. Check for misalignment
or binding of moving parts, breakage of parts and
any other condition that may affect the power
tools operation. If damaged, have the power tool
repaired before use. Many accidents are caused by
poorly maintained power tools.
f. Keep cutting tools sharp and clean.Properly
maintained cutting tools with sharp cutting edges are
less likely to bind and are easier to control.
5. Service
a. Have your power tool serviced by a qualified
repair person using only identical replacement
parts. This will ensure that the safety of the power
tool is maintained.
6. Electrical safety
Your tool is double insulated; therefore no earth
wire is required. Always check that the main voltage
corresponds to the voltage on the rating plate.
Warning! If the power cord is damaged, it must
be replaced by the manufacturer, authorized
BLACK+DECKER Service Center or an equally
qualified person in order to avoid damage or
injury. If the power cord is replaced by an equally
7. Labels on tool
The label on your tool may include the following symbols:
FEATURES (Fig. A)
1. Variable speed switch
2. Lock-on button
3. Forward/reverse slider
4. Drilling mode selector
5. Chuck
6. Depth stop
7. Side handle
ADDITIONAL SAFETY INSTRUCTIONS
FOR HAMMER DRILL
fWear ear protectors with impact drills. Exposure to
noise can cause hearing loss.
fUse auxiliary handles supplied with the tool. Loss
of control can cause personal injury.
fHold power tool by insulated gripping surfaces
when performing an operation where the cutting
tool may contact hidden wiring or its own cord.
Contact with a “live” wire will also make exposed metal
parts of the power tool “live” and shock the operator.
fUse clamps or another practical way to secure
and support the workpiece to a stable platform.
Holding the work by hand or against your body leaves
it unstable and may lead to loss of control.
fBefore drilling into walls, floors or ceilings check for
the location of wiring and pipes.
fAvoid touching the tip of a drill bit just after drilling, as
it may be hot
ASSAMBLY
Warning! Before assembly, make sure that the tool is
switched off and unplugged.
Fitting the side handle and depth stop (Fig. B)
Turn the grip counterclockwise until you can slide the
side handle (7) onto the front of the tool as shown.
fRotate the side handle into the desired position.
fInsert the depth stop (6) into the mounting hole as
shown.
fSet the drilling depth as described below.
fTighten the side handle by turning the grip clockwise.
Fitting a drill bit or screwdriver bit
Keyed chuck (Fig. C)
fOpen the chuck by turning the sleeve (9)
counterclockwise.
fInsert the bit shaft (8) into the chuck.
fInsert the chuck key (10) into each hole (11) in the side
of the chuck and turn clockwise until tight.
Removing and refitting the chuck (Fig. D)
fOpen the chuck as far as possible.
fRemove the chuck retaining screw, located in the
chuck, by turning it clockwise using a screwdriver.
fTighten an Allen key into the chuck and strike it with
a hammer as shown.
fRemove the Allen key.
fRemove the chuck by turning it counterclockwise.
fTo refit the chuck, screw it onto the spindle and secure
it with the chuck retaining screw.
Read
Instructions
Manual
Use Eye
Protection
Use Ear
Protection
V ........ Volts
A ........ Amperes
Hz ....... Hertz
W ........ Watts
min ..... minutes
..... Alternating
Current
..... Direct
Current
n0....... No-Load
Speed
...... Class II
Construction
.... Earthing
Terminal
.... Safety Alert
Symbol
.../min.. Revolutions
or Recipro-
cation per
minute
qualified person, but not authorized by
BLACK+DECKER, the warranty will not be valid.
 参阅说
明手册
 使用护
目设备
 使用护
耳设备
V��������伏特
A��������安培
Hz������赫兹
W�������瓦特
min�����分钟
������������交流电
������������直流电
n0�������空载转速
������������II级结构
������������接地终端
������������安全警
告标识
���/min� � 每分钟
旋转或
往复次
数
功能部件（图 A）
1� 变速开关
2� 锁定按钮
3� 正 / 反转滑块
4� 钻孔模式选择器
5� 夹头
6� 限深器
7� 侧手柄
组装
警告！组装前，请确保关闭工具电源并拔下
工具插头。
安装侧手柄和限深器（图 B）
逆时针转动手柄直到您可以将侧手柄(7)滑动至工
具正面为止，如图所示。
← 将侧手柄转入所需位置。
← 将深度尺(6)插入安装孔，如图所示。
← 按照以下说明设置钻孔深度。
← 通过顺时针转动手柄转紧侧手柄。
安装钻头或螺丝起子头带键夹头（图 C）
← 通过逆时针转动套管(9)打开夹头。
← 将钻头轴(8)插入夹头。
← 将夹头栓(10)插入夹头侧面的每个插孔(11)，
然后顺时针转紧。
卸下及装回夹头（图 D）
← 将夹头打开到最大位置。
← 用螺丝起子顺时针转动夹头的固定螺钉将夹
头取出。
← 将内六角起子转紧到夹头内，然后用锤子打
击，如图所示。
← 取出内六角起子。
← 逆时针转动夹头将它取出。
← 要装回夹头，可将它旋入主轴，然后用夹头固
定螺钉将它锁紧。
4 • ENGLISH
4 • ENGLISH
making any adjustments, changing accessories,
or storing power tools. Such preventive safety measures
reduce the risk of starting the power tool accidentally.
d. Store idle power tools out of the reach of children
and do not allow persons unfamiliar with the power
tool or these instructions to operate the power
tool. Power tools are dangerous in the hands
of untrained users.
e. Maintain power tools. Check for misalignment
or binding of moving parts, breakage of parts and
any other condition that may affect the power
tools operation. If damaged, have the power tool
repaired before use. Many accidents are caused by
poorly maintained power tools.
f. Keep cutting tools sharp and clean.Properly
maintained cutting tools with sharp cutting edges are
less likely to bind and are easier to control.
5. Service
a. Have your power tool serviced by a qualified
repair person using only identical replacement
parts. This will ensure that the safety of the power
tool is maintained.
6. Electrical safety
Your tool is double insulated; therefore no earth
wire is required. Always check that the main voltage
corresponds to the voltage on the rating plate.
Warning! If the power cord is damaged, it must
be replaced by the manufacturer, authorized
BLACK+DECKER Service Center or an equally
qualified person in order to avoid damage or
injury. If the power cord is replaced by an equally
7. Labels on tool
The label on your tool may include the following symbols:
FEATURES (Fig. A)
1. Variable speed switch
2. Lock-on button
3. Forward/reverse slider
4. Drilling mode selector
5. Chuck
6. Depth stop
7. Side handle
ADDITIONAL SAFETY INSTRUCTIONS
FOR HAMMER DRILL
fWear ear protectors with impact drills. Exposure to
noise can cause hearing loss.
fUse auxiliary handles supplied with the tool. Loss
of control can cause personal injury.
fHold power tool by insulated gripping surfaces
when performing an operation where the cutting
tool may contact hidden wiring or its own cord.
Contact with a “live” wire will also make exposed metal
parts of the power tool “live” and shock the operator.
fUse clamps or another practical way to secure
and support the workpiece to a stable platform.
Holding the work by hand or against your body leaves
it unstable and may lead to loss of control.
fBefore drilling into walls, floors or ceilings check for
the location of wiring and pipes.
fAvoid touching the tip of a drill bit just after drilling, as
it may be hot
ASSAMBLY
Warning! Before assembly, make sure that the tool is
switched off and unplugged.
Fitting the side handle and depth stop (Fig. B)
Turn the grip counterclockwise until you can slide the
side handle (7) onto the front of the tool as shown.
fRotate the side handle into the desired position.
fInsert the depth stop (6) into the mounting hole as
shown.
fSet the drilling depth as described below.
fTighten the side handle by turning the grip clockwise.
Fitting a drill bit or screwdriver bit
Keyed chuck (Fig. C)
fOpen the chuck by turning the sleeve (9)
counterclockwise.
fInsert the bit shaft (8) into the chuck.
fInsert the chuck key (10) into each hole (11) in the side
of the chuck and turn clockwise until tight.
Removing and refitting the chuck (Fig. D)
fOpen the chuck as far as possible.
fRemove the chuck retaining screw, located in the
chuck, by turning it clockwise using a screwdriver.
fTighten an Allen key into the chuck and strike it with
a hammer as shown.
fRemove the Allen key.
fRemove the chuck by turning it counterclockwise.
fTo refit the chuck, screw it onto the spindle and secure
it with the chuck retaining screw.
Read
Instructions
Manual
Use Eye
Protection
Use Ear
Protection
V ........ Volts
A ........ Amperes
Hz ....... Hertz
W ........ Watts
min ..... minutes
..... Alternating
Current
..... Direct
Current
n0....... No-Load
Speed
...... Class II
Construction
.... Earthing
Terminal
.... Safety Alert
Symbol
.../min.. Revolutions
or Recipro-
cation per
minute
qualified person, but not authorized by
BLACK+DECKER, the warranty will not be valid.
4 • ENGLISH
4 • ENGLISH
making any adjustments, changing accessories,
or storing power tools. Such preventive safety measures
reduce the risk of starting the power tool accidentally.
d. Store idle power tools out of the reach of children
and do not allow persons unfamiliar with the power
tool or these instructions to operate the power
tool. Power tools are dangerous in the hands
of untrained users.
e. Maintain power tools. Check for misalignment
or binding of moving parts, breakage of parts and
any other condition that may affect the power
tools operation. If damaged, have the power tool
repaired before use. Many accidents are caused by
poorly maintained power tools.
f. Keep cutting tools sharp and clean.Properly
maintained cutting tools with sharp cutting edges are
less likely to bind and are easier to control.
5. Service
a. Have your power tool serviced by a qualified
repair person using only identical replacement
parts. This will ensure that the safety of the power
tool is maintained.
6. Electrical safety
Your tool is double insulated; therefore no earth
wire is required. Always check that the main voltage
corresponds to the voltage on the rating plate.
Warning! If the power cord is damaged, it must
be replaced by the manufacturer, authorized
BLACK+DECKER Service Center or an equally
qualified person in order to avoid damage or
injury. If the power cord is replaced by an equally
7. Labels on tool
The label on your tool may include the following symbols:
FEATURES (Fig. A)
1. Variable speed switch
2. Lock-on button
3. Forward/reverse slider
4. Drilling mode selector
5. Chuck
6. Depth stop
7. Side handle
ADDITIONAL SAFETY INSTRUCTIONS
FOR HAMMER DRILL
fWear ear protectors with impact drills. Exposure to
noise can cause hearing loss.
fUse auxiliary handles supplied with the tool. Loss
of control can cause personal injury.
fHold power tool by insulated gripping surfaces
when performing an operation where the cutting
tool may contact hidden wiring or its own cord.
Contact with a “live” wire will also make exposed metal
parts of the power tool “live” and shock the operator.
fUse clamps or another practical way to secure
and support the workpiece to a stable platform.
Holding the work by hand or against your body leaves
it unstable and may lead to loss of control.
fBefore drilling into walls, floors or ceilings check for
the location of wiring and pipes.
fAvoid touching the tip of a drill bit just after drilling, as
it may be hot
ASSAMBLY
Warning! Before assembly, make sure that the tool is
switched off and unplugged.
Fitting the side handle and depth stop (Fig. B)
Turn the grip counterclockwise until you can slide the
side handle (7) onto the front of the tool as shown.
fRotate the side handle into the desired position.
fInsert the depth stop (6) into the mounting hole as
shown.
fSet the drilling depth as described below.
fTighten the side handle by turning the grip clockwise.
Fitting a drill bit or screwdriver bit
Keyed chuck (Fig. C)
fOpen the chuck by turning the sleeve (9)
counterclockwise.
fInsert the bit shaft (8) into the chuck.
fInsert the chuck key (10) into each hole (11) in the side
of the chuck and turn clockwise until tight.
Removing and refitting the chuck (Fig. D)
fOpen the chuck as far as possible.
fRemove the chuck retaining screw, located in the
chuck, by turning it clockwise using a screwdriver.
fTighten an Allen key into the chuck and strike it with
a hammer as shown.
fRemove the Allen key.
fRemove the chuck by turning it counterclockwise.
fTo refit the chuck, screw it onto the spindle and secure
it with the chuck retaining screw.
Read
Instructions
Manual
Use Eye
Protection
Use Ear
Protection
V ........ Volts
A ........ Amperes
Hz ....... Hertz
W ........ Watts
min ..... minutes
..... Alternating
Current
..... Direct
Current
n0....... No-Load
Speed
...... Class II
Construction
.... Earthing
Terminal
.... Safety Alert
Symbol
.../min.. Revolutions
or Recipro-
cation per
minute
qualified person, but not authorized by
BLACK+DECKER, the warranty will not be valid.
4 • ENGLISH
4 • ENGLISH
making any adjustments, changing accessories,
or storing power tools. Such preventive safety measures
reduce the risk of starting the power tool accidentally.
d. Store idle power tools out of the reach of children
and do not allow persons unfamiliar with the power
tool or these instructions to operate the power
tool. Power tools are dangerous in the hands
of untrained users.
e. Maintain power tools. Check for misalignment
or binding of moving parts, breakage of parts and
any other condition that may affect the power
tools operation. If damaged, have the power tool
repaired before use. Many accidents are caused by
poorly maintained power tools.
f. Keep cutting tools sharp and clean.Properly
maintained cutting tools with sharp cutting edges are
less likely to bind and are easier to control.
5. Service
a. Have your power tool serviced by a qualified
repair person using only identical replacement
parts. This will ensure that the safety of the power
tool is maintained.
6. Electrical safety
Your tool is double insulated; therefore no earth
wire is required. Always check that the main voltage
corresponds to the voltage on the rating plate.
Warning! If the power cord is damaged, it must
be replaced by the manufacturer, authorized
BLACK+DECKER Service Center or an equally
qualified person in order to avoid damage or
injury. If the power cord is replaced by an equally
7. Labels on tool
The label on your tool may include the following symbols:
FEATURES (Fig. A)
1. Variable speed switch
2. Lock-on button
3. Forward/reverse slider
4. Drilling mode selector
5. Chuck
6. Depth stop
7. Side handle
ADDITIONAL SAFETY INSTRUCTIONS
FOR HAMMER DRILL
fWear ear protectors with impact drills. Exposure to
noise can cause hearing loss.
fUse auxiliary handles supplied with the tool. Loss
of control can cause personal injury.
fHold power tool by insulated gripping surfaces
when performing an operation where the cutting
tool may contact hidden wiring or its own cord.
Contact with a “live” wire will also make exposed metal
parts of the power tool “live” and shock the operator.
fUse clamps or another practical way to secure
and support the workpiece to a stable platform.
Holding the work by hand or against your body leaves
it unstable and may lead to loss of control.
fBefore drilling into walls, floors or ceilings check for
the location of wiring and pipes.
fAvoid touching the tip of a drill bit just after drilling, as
it may be hot
ASSAMBLY
Warning! Before assembly, make sure that the tool is
switched off and unplugged.
Fitting the side handle and depth stop (Fig. B)
Turn the grip counterclockwise until you can slide the
side handle (7) onto the front of the tool as shown.
fRotate the side handle into the desired position.
fInsert the depth stop (6) into the mounting hole as
shown.
fSet the drilling depth as described below.
fTighten the side handle by turning the grip clockwise.
Fitting a drill bit or screwdriver bit
Keyed chuck (Fig. C)
fOpen the chuck by turning the sleeve (9)
counterclockwise.
fInsert the bit shaft (8) into the chuck.
fInsert the chuck key (10) into each hole (11) in the side
of the chuck and turn clockwise until tight.
Removing and refitting the chuck (Fig. D)
fOpen the chuck as far as possible.
fRemove the chuck retaining screw, located in the
chuck, by turning it clockwise using a screwdriver.
fTighten an Allen key into the chuck and strike it with
a hammer as shown.
fRemove the Allen key.
fRemove the chuck by turning it counterclockwise.
fTo refit the chuck, screw it onto the spindle and secure
it with the chuck retaining screw.
Read
Instructions
Manual
Use Eye
Protection
Use Ear
Protection
V ........ Volts
A ........ Amperes
Hz ....... Hertz
W ........ Watts
min ..... minutes
..... Alternating
Current
..... Direct
Current
n0....... No-Load
Speed
...... Class II
Construction
.... Earthing
Terminal
.... Safety Alert
Symbol
.../min.. Revolutions
or Recipro-
cation per
minute
qualified person, but not authorized by
BLACK+DECKER, the warranty will not be valid.
4 • ENGLISH
4 • ENGLISH
making any adjustments, changing accessories,
or storing power tools. Such preventive safety measures
reduce the risk of starting the power tool accidentally.
d. Store idle power tools out of the reach of children
and do not allow persons unfamiliar with the power
tool or these instructions to operate the power
tool. Power tools are dangerous in the hands
of untrained users.
e. Maintain power tools. Check for misalignment
or binding of moving parts, breakage of parts and
any other condition that may affect the power
tools operation. If damaged, have the power tool
repaired before use. Many accidents are caused by
poorly maintained power tools.
f. Keep cutting tools sharp and clean.Properly
maintained cutting tools with sharp cutting edges are
less likely to bind and are easier to control.
5. Service
a. Have your power tool serviced by a qualified
repair person using only identical replacement
parts. This will ensure that the safety of the power
tool is maintained.
6. Electrical safety
Your tool is double insulated; therefore no earth
wire is required. Always check that the main voltage
corresponds to the voltage on the rating plate.
Warning! If the power cord is damaged, it must
be replaced by the manufacturer, authorized
BLACK+DECKER Service Center or an equally
qualified person in order to avoid damage or
injury. If the power cord is replaced by an equally
7. Labels on tool
The label on your tool may include the following symbols:
FEATURES (Fig. A)
1. Variable speed switch
2. Lock-on button
3. Forward/reverse slider
4. Drilling mode selector
5. Chuck
6. Depth stop
7. Side handle
ADDITIONAL SAFETY INSTRUCTIONS
FOR HAMMER DRILL
fWear ear protectors with impact drills. Exposure to
noise can cause hearing loss.
fUse auxiliary handles supplied with the tool. Loss
of control can cause personal injury.
fHold power tool by insulated gripping surfaces
when performing an operation where the cutting
tool may contact hidden wiring or its own cord.
Contact with a “live” wire will also make exposed metal
parts of the power tool “live” and shock the operator.
fUse clamps or another practical way to secure
and support the workpiece to a stable platform.
Holding the work by hand or against your body leaves
it unstable and may lead to loss of control.
fBefore drilling into walls, floors or ceilings check for
the location of wiring and pipes.
fAvoid touching the tip of a drill bit just after drilling, as
it may be hot
ASSAMBLY
Warning! Before assembly, make sure that the tool is
switched off and unplugged.
Fitting the side handle and depth stop (Fig. B)
Turn the grip counterclockwise until you can slide the
side handle (7) onto the front of the tool as shown.
fRotate the side handle into the desired position.
fInsert the depth stop (6) into the mounting hole as
shown.
fSet the drilling depth as described below.
fTighten the side handle by turning the grip clockwise.
Fitting a drill bit or screwdriver bit
Keyed chuck (Fig. C)
fOpen the chuck by turning the sleeve (9)
counterclockwise.
fInsert the bit shaft (8) into the chuck.
fInsert the chuck key (10) into each hole (11) in the side
of the chuck and turn clockwise until tight.
Removing and refitting the chuck (Fig. D)
fOpen the chuck as far as possible.
fRemove the chuck retaining screw, located in the
chuck, by turning it clockwise using a screwdriver.
fTighten an Allen key into the chuck and strike it with
a hammer as shown.
fRemove the Allen key.
fRemove the chuck by turning it counterclockwise.
fTo refit the chuck, screw it onto the spindle and secure
it with the chuck retaining screw.
Read
Instructions
Manual
Use Eye
Protection
Use Ear
Protection
V ........ Volts
A ........ Amperes
Hz ....... Hertz
W ........ Watts
min ..... minutes
..... Alternating
Current
..... Direct
Current
n0....... No-Load
Speed
...... Class II
Construction
.... Earthing
Terminal
.... Safety Alert
Symbol
.../min.. Revolutions
or Recipro-
cation per
minute
qualified person, but not authorized by
BLACK+DECKER, the warranty will not be valid.
4 • ENGLISH
4 • ENGLISH
making any adjustments, changing accessories,
or storing power tools. Such preventive safety measures
reduce the risk of starting the power tool accidentally.
d. Store idle power tools out of the reach of children
and do not allow persons unfamiliar with the power
tool or these instructions to operate the power
tool. Power tools are dangerous in the hands
of untrained users.
e. Maintain power tools. Check for misalignment
or binding of moving parts, breakage of parts and
any other condition that may affect the power
tools operation. If damaged, have the power tool
repaired before use. Many accidents are caused by
poorly maintained power tools.
f. Keep cutting tools sharp and clean.Properly
maintained cutting tools with sharp cutting edges are
less likely to bind and are easier to control.
5. Service
a. Have your power tool serviced by a qualified
repair person using only identical replacement
parts. This will ensure that the safety of the power
tool is maintained.
6. Electrical safety
Your tool is double insulated; therefore no earth
wire is required. Always check that the main voltage
corresponds to the voltage on the rating plate.
Warning! If the power cord is damaged, it must
be replaced by the manufacturer, authorized
BLACK+DECKER Service Center or an equally
qualified person in order to avoid damage or
injury. If the power cord is replaced by an equally
7. Labels on tool
The label on your tool may include the following symbols:
FEATURES (Fig. A)
1. Variable speed switch
2. Lock-on button
3. Forward/reverse slider
4. Drilling mode selector
5. Chuck
6. Depth stop
7. Side handle
ADDITIONAL SAFETY INSTRUCTIONS
FOR HAMMER DRILL
fWear ear protectors with impact drills. Exposure to
noise can cause hearing loss.
fUse auxiliary handles supplied with the tool. Loss
of control can cause personal injury.
fHold power tool by insulated gripping surfaces
when performing an operation where the cutting
tool may contact hidden wiring or its own cord.
Contact with a “live” wire will also make exposed metal
parts of the power tool “live” and shock the operator.
fUse clamps or another practical way to secure
and support the workpiece to a stable platform.
Holding the work by hand or against your body leaves
it unstable and may lead to loss of control.
fBefore drilling into walls, floors or ceilings check for
the location of wiring and pipes.
fAvoid touching the tip of a drill bit just after drilling, as
it may be hot
ASSAMBLY
Warning! Before assembly, make sure that the tool is
switched off and unplugged.
Fitting the side handle and depth stop (Fig. B)
Turn the grip counterclockwise until you can slide the
side handle (7) onto the front of the tool as shown.
fRotate the side handle into the desired position.
fInsert the depth stop (6) into the mounting hole as
shown.
fSet the drilling depth as described below.
fTighten the side handle by turning the grip clockwise.
Fitting a drill bit or screwdriver bit
Keyed chuck (Fig. C)
fOpen the chuck by turning the sleeve (9)
counterclockwise.
fInsert the bit shaft (8) into the chuck.
fInsert the chuck key (10) into each hole (11) in the side
of the chuck and turn clockwise until tight.
Removing and refitting the chuck (Fig. D)
fOpen the chuck as far as possible.
fRemove the chuck retaining screw, located in the
chuck, by turning it clockwise using a screwdriver.
fTighten an Allen key into the chuck and strike it with
a hammer as shown.
fRemove the Allen key.
fRemove the chuck by turning it counterclockwise.
fTo refit the chuck, screw it onto the spindle and secure
it with the chuck retaining screw.
Read
Instructions
Manual
Use Eye
Protection
Use Ear
Protection
V ........ Volts
A ........ Amperes
Hz ....... Hertz
W ........ Watts
min ..... minutes
..... Alternating
Current
..... Direct
Current
n0....... No-Load
Speed
...... Class II
Construction
.... Earthing
Terminal
.... Safety Alert
Symbol
.../min.. Revolutions
or Recipro-
cation per
minute
qualified person, but not authorized by
BLACK+DECKER, the warranty will not be valid.
4 • ENGLISH
4 • ENGLISH
making any adjustments, changing accessories,
or storing power tools. Such preventive safety measures
reduce the risk of starting the power tool accidentally.
d. Store idle power tools out of the reach of children
and do not allow persons unfamiliar with the power
tool or these instructions to operate the power
tool. Power tools are dangerous in the hands
of untrained users.
e. Maintain power tools. Check for misalignment
or binding of moving parts, breakage of parts and
any other condition that may affect the power
tools operation. If damaged, have the power tool
repaired before use. Many accidents are caused by
poorly maintained power tools.
f. Keep cutting tools sharp and clean.Properly
maintained cutting tools with sharp cutting edges are
less likely to bind and are easier to control.
5. Service
a. Have your power tool serviced by a qualified
repair person using only identical replacement
parts. This will ensure that the safety of the power
tool is maintained.
6. Electrical safety
Your tool is double insulated; therefore no earth
wire is required. Always check that the main voltage
corresponds to the voltage on the rating plate.
Warning! If the power cord is damaged, it must
be replaced by the manufacturer, authorized
BLACK+DECKER Service Center or an equally
qualified person in order to avoid damage or
injury. If the power cord is replaced by an equally
7. Labels on tool
The label on your tool may include the following symbols:
FEATURES (Fig. A)
1. Variable speed switch
2. Lock-on button
3. Forward/reverse slider
4. Drilling mode selector
5. Chuck
6. Depth stop
7. Side handle
ADDITIONAL SAFETY INSTRUCTIONS
FOR HAMMER DRILL
fWear ear protectors with impact drills. Exposure to
noise can cause hearing loss.
fUse auxiliary handles supplied with the tool. Loss
of control can cause personal injury.
fHold power tool by insulated gripping surfaces
when performing an operation where the cutting
tool may contact hidden wiring or its own cord.
Contact with a “live” wire will also make exposed metal
parts of the power tool “live” and shock the operator.
fUse clamps or another practical way to secure
and support the workpiece to a stable platform.
Holding the work by hand or against your body leaves
it unstable and may lead to loss of control.
fBefore drilling into walls, floors or ceilings check for
the location of wiring and pipes.
fAvoid touching the tip of a drill bit just after drilling, as
it may be hot
ASSAMBLY
Warning! Before assembly, make sure that the tool is
switched off and unplugged.
Fitting the side handle and depth stop (Fig. B)
Turn the grip counterclockwise until you can slide the
side handle (7) onto the front of the tool as shown.
fRotate the side handle into the desired position.
fInsert the depth stop (6) into the mounting hole as
shown.
fSet the drilling depth as described below.
fTighten the side handle by turning the grip clockwise.
Fitting a drill bit or screwdriver bit
Keyed chuck (Fig. C)
fOpen the chuck by turning the sleeve (9)
counterclockwise.
fInsert the bit shaft (8) into the chuck.
fInsert the chuck key (10) into each hole (11) in the side
of the chuck and turn clockwise until tight.
Removing and refitting the chuck (Fig. D)
fOpen the chuck as far as possible.
fRemove the chuck retaining screw, located in the
chuck, by turning it clockwise using a screwdriver.
fTighten an Allen key into the chuck and strike it with
a hammer as shown.
fRemove the Allen key.
fRemove the chuck by turning it counterclockwise.
fTo refit the chuck, screw it onto the spindle and secure
it with the chuck retaining screw.
Read
Instructions
Manual
Use Eye
Protection
Use Ear
Protection
V ........ Volts
A ........ Amperes
Hz ....... Hertz
W ........ Watts
min ..... minutes
..... Alternating
Current
..... Direct
Current
n0....... No-Load
Speed
...... Class II
Construction
.... Earthing
Terminal
.... Safety Alert
Symbol
.../min.. Revolutions
or Recipro-
cation per
minute
qualified person, but not authorized by
BLACK+DECKER, the warranty will not be valid.
4 • ENGLISH
4 • ENGLISH
making any adjustments, changing accessories,
or storing power tools. Such preventive safety measures
reduce the risk of starting the power tool accidentally.
d. Store idle power tools out of the reach of children
and do not allow persons unfamiliar with the power
tool or these instructions to operate the power
tool. Power tools are dangerous in the hands
of untrained users.
e. Maintain power tools. Check for misalignment
or binding of moving parts, breakage of parts and
any other condition that may affect the power
tools operation. If damaged, have the power tool
repaired before use. Many accidents are caused by
poorly maintained power tools.
f. Keep cutting tools sharp and clean.Properly
maintained cutting tools with sharp cutting edges are
less likely to bind and are easier to control.
5. Service
a. Have your power tool serviced by a qualified
repair person using only identical replacement
parts. This will ensure that the safety of the power
tool is maintained.
6. Electrical safety
Your tool is double insulated; therefore no earth
wire is required. Always check that the main voltage
corresponds to the voltage on the rating plate.
Warning! If the power cord is damaged, it must
be replaced by the manufacturer, authorized
BLACK+DECKER Service Center or an equally
qualified person in order to avoid damage or
injury. If the power cord is replaced by an equally
7. Labels on tool
The label on your tool may include the following symbols:
FEATURES (Fig. A)
1. Variable speed switch
2. Lock-on button
3. Forward/reverse slider
4. Drilling mode selector
5. Chuck
6. Depth stop
7. Side handle
ADDITIONAL SAFETY INSTRUCTIONS
FOR HAMMER DRILL
fWear ear protectors with impact drills. Exposure to
noise can cause hearing loss.
fUse auxiliary handles supplied with the tool. Loss
of control can cause personal injury.
fHold power tool by insulated gripping surfaces
when performing an operation where the cutting
tool may contact hidden wiring or its own cord.
Contact with a “live” wire will also make exposed metal
parts of the power tool “live” and shock the operator.
fUse clamps or another practical way to secure
and support the workpiece to a stable platform.
Holding the work by hand or against your body leaves
it unstable and may lead to loss of control.
fBefore drilling into walls, floors or ceilings check for
the location of wiring and pipes.
fAvoid touching the tip of a drill bit just after drilling, as
it may be hot
ASSAMBLY
Warning! Before assembly, make sure that the tool is
switched off and unplugged.
Fitting the side handle and depth stop (Fig. B)
Turn the grip counterclockwise until you can slide the
side handle (7) onto the front of the tool as shown.
fRotate the side handle into the desired position.
fInsert the depth stop (6) into the mounting hole as
shown.
fSet the drilling depth as described below.
fTighten the side handle by turning the grip clockwise.
Fitting a drill bit or screwdriver bit
Keyed chuck (Fig. C)
fOpen the chuck by turning the sleeve (9)
counterclockwise.
fInsert the bit shaft (8) into the chuck.
fInsert the chuck key (10) into each hole (11) in the side
of the chuck and turn clockwise until tight.
Removing and refitting the chuck (Fig. D)
fOpen the chuck as far as possible.
fRemove the chuck retaining screw, located in the
chuck, by turning it clockwise using a screwdriver.
fTighten an Allen key into the chuck and strike it with
a hammer as shown.
fRemove the Allen key.
fRemove the chuck by turning it counterclockwise.
fTo refit the chuck, screw it onto the spindle and secure
it with the chuck retaining screw.
Read
Instructions
Manual
Use Eye
Protection
Use Ear
Protection
V ........ Volts
A ........ Amperes
Hz ....... Hertz
W ........ Watts
min ..... minutes
..... Alternating
Current
..... Direct
Current
n0....... No-Load
Speed
...... Class II
Construction
.... Earthing
Terminal
.... Safety Alert
Symbol
.../min.. Revolutions
or Recipro-
cation per
minute
qualified person, but not authorized by
BLACK+DECKER, the warranty will not be valid.
4 • ENGLISH
4 • ENGLISH
making any adjustments, changing accessories,
or storing power tools. Such preventive safety measures
reduce the risk of starting the power tool accidentally.
d. Store idle power tools out of the reach of children
and do not allow persons unfamiliar with the power
tool or these instructions to operate the power
tool. Power tools are dangerous in the hands
of untrained users.
e. Maintain power tools. Check for misalignment
or binding of moving parts, breakage of parts and
any other condition that may affect the power
tools operation. If damaged, have the power tool
repaired before use. Many accidents are caused by
poorly maintained power tools.
f. Keep cutting tools sharp and clean.Properly
maintained cutting tools with sharp cutting edges are
less likely to bind and are easier to control.
5. Service
a. Have your power tool serviced by a qualified
repair person using only identical replacement
parts. This will ensure that the safety of the power
tool is maintained.
6. Electrical safety
Your tool is double insulated; therefore no earth
wire is required. Always check that the main voltage
corresponds to the voltage on the rating plate.
Warning! If the power cord is damaged, it must
be replaced by the manufacturer, authorized
BLACK+DECKER Service Center or an equally
qualified person in order to avoid damage or
injury. If the power cord is replaced by an equally
7. Labels on tool
The label on your tool may include the following symbols:
FEATURES (Fig. A)
1. Variable speed switch
2. Lock-on button
3. Forward/reverse slider
4. Drilling mode selector
5. Chuck
6. Depth stop
7. Side handle
ADDITIONAL SAFETY INSTRUCTIONS
FOR HAMMER DRILL
fWear ear protectors with impact drills. Exposure to
noise can cause hearing loss.
fUse auxiliary handles supplied with the tool. Loss
of control can cause personal injury.
fHold power tool by insulated gripping surfaces
when performing an operation where the cutting
tool may contact hidden wiring or its own cord.
Contact with a “live” wire will also make exposed metal
parts of the power tool “live” and shock the operator.
fUse clamps or another practical way to secure
and support the workpiece to a stable platform.
Holding the work by hand or against your body leaves
it unstable and may lead to loss of control.
fBefore drilling into walls, floors or ceilings check for
the location of wiring and pipes.
fAvoid touching the tip of a drill bit just after drilling, as
it may be hot
ASSAMBLY
Warning! Before assembly, make sure that the tool is
switched off and unplugged.
Fitting the side handle and depth stop (Fig. B)
Turn the grip counterclockwise until you can slide the
side handle (7) onto the front of the tool as shown.
fRotate the side handle into the desired position.
fInsert the depth stop (6) into the mounting hole as
shown.
fSet the drilling depth as described below.
fTighten the side handle by turning the grip clockwise.
Fitting a drill bit or screwdriver bit
Keyed chuck (Fig. C)
fOpen the chuck by turning the sleeve (9)
counterclockwise.
fInsert the bit shaft (8) into the chuck.
fInsert the chuck key (10) into each hole (11) in the side
of the chuck and turn clockwise until tight.
Removing and refitting the chuck (Fig. D)
fOpen the chuck as far as possible.
fRemove the chuck retaining screw, located in the
chuck, by turning it clockwise using a screwdriver.
fTighten an Allen key into the chuck and strike it with
a hammer as shown.
fRemove the Allen key.
fRemove the chuck by turning it counterclockwise.
fTo refit the chuck, screw it onto the spindle and secure
it with the chuck retaining screw.
Read
Instructions
Manual
Use Eye
Protection
Use Ear
Protection
V ........ Volts
A ........ Amperes
Hz ....... Hertz
W ........ Watts
min ..... minutes
..... Alternating
Current
..... Direct
Current
n0....... No-Load
Speed
...... Class II
Construction
.... Earthing
Terminal
.... Safety Alert
Symbol
.../min.. Revolutions
or Recipro-
cation per
minute
qualified person, but not authorized by
BLACK+DECKER, the warranty will not be valid.

简体中文●9
用途
警告！请让工具在自有速度下工作。请勿过载。
警告！在墙上、地板或天花板上钻孔之前，请检
查电线和管道位置。
选择旋转方向（图 E）
如果要钻孔和转紧螺丝，请使用向前（顺时针）旋
转。如果要转松螺丝或取出卡住的钻头，使用向后
（逆时针）旋转。
► 如果要选择向前旋转，将正 / 反转滑块(3)拨
到中心位置。
► 要选择向后旋转，将正 / 反转滑块拨到左边。
警告！在马达运行时切勿更改旋转方向。
选择钻孔模式
► 在砖石上钻孔时，将钻孔模式选择器(3)设置
到
ENGLISH •5
ENGLISH • 5
USE
Warning! Let the tool work at its own pace. Do not
overload.
Warning! Before drilling into walls, floors or ceilings,
check for the location of wiring and pipes.
Selecting the direction of rotation (Fig. E)
For drilling and for tightening screws, use forward
(clockwise) rotation. For loosening screws or removing a
jammed drill bit, use reverse (counterclockwise) rotation.
fTo select forward rotation, push the forward/reverse
slider (3) to the centre position.
fTo select reverse rotation, push the forward/reverse
slider to the left.
Warning! Never change the direction of rotation while
the motor is running.
Selecting the drilling mode
fFor drilling in masonry, set the drilling mode selector
(3) to the position.
fFor drilling in other materials and for screwdriving, set
the drilling mode selector to the position.
Setting the drilling depth (Fig. F)
fSlacken the side handle (7) by turning the grip
counterclockwise.
fSet the depth stop (6) to the desired position. The
maximum drilling depth is equal to the distance
between the tip of the drill bit and the front end of the
depth stop.
fTighten the side handle by turning the grip clockwise.
Switching on and off
fTo switch the tool on, press the speed switch (1).
For tools with variable speed switch, the tool speed
depends on how far you press the switch. As a
general rule, use low speeds for large diameter
drill bits and high speeds for smaller diameter drill bits.
fFor continuous operation, press the lock-on button (2)
and release the speed switch. This option is available
only at full speed. This option does not work in reverse
rotation. Reverse rotation available only for HD500.
fTo switch the tool off, release the speed switch.
To switch the tool off when in continuous operation,
press the speed switch once more and release it.
MAINTENANCE
Keep guards, air vents and the motor housing as clear as
possible of dust and dirt. Wipe with a clean cloth and blow
through with a low-pressure air supply. Excessive build-up
of metal dust can cause tracking of electrical current from
the internal parts to exposed metal parts.
Important! To assure product SAFETY and RELIABILITY,
repairs, maintenance and adjustment (other than those
listed in this manual) should be performed by authorized
service centers or other qualified service personnel,
always using identical replacement parts.
ACCESSORIES
Recommended accessories for use with your product
are available from your local dealer or authorized service
center.
PROTECTING THE ENVIRONMENT
Separate collection. This product must not be
disposed of with normal household waste.
Should you find one day that your
BLACK+DECKER product needs replacement, or
if it is of no further use to you, do not dispose of it
with household waste. Make this product available
for separate collection.
Separate collection of used products and packaging
allows materials to be recycled and used again.
Re-use of recycled materials helps prevent
environmental pollution and reduces the demand
for raw materials. Local regulations may provide for
separate collection of electrical products from the
household, at municipal waste sites or by the
retailer when you purchase a new product.
SERVICE INFORMATION
BLACK+DECKER offers a full network of company-owned
and authorized service locations throughtout Asia. All
BLACK+DECKER Service Centers are staffed with trained
personnel to provide customers with efficient and reliable
product service.
Whether you need technical advice, repair, or genuine
factory replacement parts, contact the BLACK+DECKER
location nearest to you.
NOTE
fBLACK+DECKER’s policy is one of continuous
improvement to our products and, as such, we reserve
the right to change product specifications without prior
notice.
fStandard equipment and accessories may vary by
country.
fProduct specifications may differ by country.
fComplete product range may not be available in all
countries. Contact your local BLACK+DECKER
dealers for range availability.
位置。
► 在其他材料上钻孔以及执行螺旋操作时，将钻
孔模式选择器设置到
ENGLISH •5
ENGLISH • 5
USE
Warning! Let the tool work at its own pace. Do not
overload.
Warning! Before drilling into walls, floors or ceilings,
check for the location of wiring and pipes.
Selecting the direction of rotation (Fig. E)
For drilling and for tightening screws, use forward
(clockwise) rotation. For loosening screws or removing a
jammed drill bit, use reverse (counterclockwise) rotation.
fTo select forward rotation, push the forward/reverse
slider (3) to the centre position.
fTo select reverse rotation, push the forward/reverse
slider to the left.
Warning! Never change the direction of rotation while
the motor is running.
Selecting the drilling mode
fFor drilling in masonry, set the drilling mode selector
(3) to the position.
fFor drilling in other materials and for screwdriving, set
the drilling mode selector to the position.
Setting the drilling depth (Fig. F)
fSlacken the side handle (7) by turning the grip
counterclockwise.
fSet the depth stop (6) to the desired position. The
maximum drilling depth is equal to the distance
between the tip of the drill bit and the front end of the
depth stop.
fTighten the side handle by turning the grip clockwise.
Switching on and off
fTo switch the tool on, press the speed switch (1).
For tools with variable speed switch, the tool speed
depends on how far you press the switch. As a
general rule, use low speeds for large diameter
drill bits and high speeds for smaller diameter drill bits.
fFor continuous operation, press the lock-on button (2)
and release the speed switch. This option is available
only at full speed. This option does not work in reverse
rotation. Reverse rotation available only for HD500.
fTo switch the tool off, release the speed switch.
To switch the tool off when in continuous operation,
press the speed switch once more and release it.
MAINTENANCE
Keep guards, air vents and the motor housing as clear as
possible of dust and dirt. Wipe with a clean cloth and blow
through with a low-pressure air supply. Excessive build-up
of metal dust can cause tracking of electrical current from
the internal parts to exposed metal parts.
Important! To assure product SAFETY and RELIABILITY,
repairs, maintenance and adjustment (other than those
listed in this manual) should be performed by authorized
service centers or other qualified service personnel,
always using identical replacement parts.
ACCESSORIES
Recommended accessories for use with your product
are available from your local dealer or authorized service
center.
PROTECTING THE ENVIRONMENT
Separate collection. This product must not be
disposed of with normal household waste.
Should you find one day that your
BLACK+DECKER product needs replacement, or
if it is of no further use to you, do not dispose of it
with household waste. Make this product available
for separate collection.
Separate collection of used products and packaging
allows materials to be recycled and used again.
Re-use of recycled materials helps prevent
environmental pollution and reduces the demand
for raw materials. Local regulations may provide for
separate collection of electrical products from the
household, at municipal waste sites or by the
retailer when you purchase a new product.
SERVICE INFORMATION
BLACK+DECKER offers a full network of company-owned
and authorized service locations throughtout Asia. All
BLACK+DECKER Service Centers are staffed with trained
personnel to provide customers with efficient and reliable
product service.
Whether you need technical advice, repair, or genuine
factory replacement parts, contact the BLACK+DECKER
location nearest to you.
NOTE
fBLACK+DECKER’s policy is one of continuous
improvement to our products and, as such, we reserve
the right to change product specifications without prior
notice.
fStandard equipment and accessories may vary by
country.
fProduct specifications may differ by country.
fComplete product range may not be available in all
countries. Contact your local BLACK+DECKER
dealers for range availability.
位置。
设置钻孔深度（图 F）
► 通过逆时针转动手柄转松侧手柄(7)。
► 将深度尺(6)设置到所需位置。最大钻孔深度
相等于钻头尖端与深度尺前末端之间的距离。
► 通过顺时针转动手柄转紧侧手柄。
开启和关闭
► 要打开工具电源，请按下速度开关(1)。对于
采用变速开关的工具，工具速度取决于按下开
关的程度。按照常规，使用大直径钻头时采用
低速，使用小直径钻头时则采用高速。
► 要使工具连续运行，按下锁定按钮(2)然后松
开速度开关。此选项只在全速运作时可用。
► 若要关闭工具，请松开速度开关。要在持续操
作时关闭工具电源，请再次按下速度开关然后
放开。
维护
请尽量避免粉尘和碎屑在通风口和电机外壳上积
聚。使用干净的抹布拭擦，并使用低压气源吹走粉
尘和碎屑。过多的金属屑堆积可能会导致电流从内
部件传导至暴露的金属部件。
重要！为了确保产品安全及可靠，所有的维修、
保养和调节，除了本手册中列出的以外，均应该由
授权的服务中心或合格的维修服务人员执行，并始
终使用相同的备件。
ENGLISH •5
ENGLISH • 5
USE
Warning! Let the tool work at its own pace. Do not
overload.
Warning! Before drilling into walls, floors or ceilings,
check for the location of wiring and pipes.
Selecting the direction of rotation (Fig. E)
For drilling and for tightening screws, use forward
(clockwise) rotation. For loosening screws or removing a
jammed drill bit, use reverse (counterclockwise) rotation.
fTo select forward rotation, push the forward/reverse
slider (3) to the centre position.
fTo select reverse rotation, push the forward/reverse
slider to the left.
Warning! Never change the direction of rotation while
the motor is running.
Selecting the drilling mode
fFor drilling in masonry, set the drilling mode selector
(3) to the position.
fFor drilling in other materials and for screwdriving, set
the drilling mode selector to the position.
Setting the drilling depth (Fig. F)
fSlacken the side handle (7) by turning the grip
counterclockwise.
fSet the depth stop (6) to the desired position. The
maximum drilling depth is equal to the distance
between the tip of the drill bit and the front end of the
depth stop.
fTighten the side handle by turning the grip clockwise.
Switching on and off
fTo switch the tool on, press the speed switch (1).
For tools with variable speed switch, the tool speed
depends on how far you press the switch. As a
general rule, use low speeds for large diameter
drill bits and high speeds for smaller diameter drill bits.
fFor continuous operation, press the lock-on button (2)
and release the speed switch. This option is available
only at full speed. This option does not work in reverse
rotation. Reverse rotation available only for HD500.
fTo switch the tool off, release the speed switch.
To switch the tool off when in continuous operation,
press the speed switch once more and release it.
MAINTENANCE
Keep guards, air vents and the motor housing as clear as
possible of dust and dirt. Wipe with a clean cloth and blow
through with a low-pressure air supply. Excessive build-up
of metal dust can cause tracking of electrical current from
the internal parts to exposed metal parts.
Important! To assure product SAFETY and RELIABILITY,
repairs, maintenance and adjustment (other than those
listed in this manual) should be performed by authorized
service centers or other qualified service personnel,
always using identical replacement parts.
ACCESSORIES
Recommended accessories for use with your product
are available from your local dealer or authorized service
center.
PROTECTING THE ENVIRONMENT
Separate collection. This product must not be
disposed of with normal household waste.
Should you find one day that your
BLACK+DECKER product needs replacement, or
if it is of no further use to you, do not dispose of it
with household waste. Make this product available
for separate collection.
Separate collection of used products and packaging
allows materials to be recycled and used again.
Re-use of recycled materials helps prevent
environmental pollution and reduces the demand
for raw materials. Local regulations may provide for
separate collection of electrical products from the
household, at municipal waste sites or by the
retailer when you purchase a new product.
SERVICE INFORMATION
BLACK+DECKER offers a full network of company-owned
and authorized service locations throughtout Asia. All
BLACK+DECKER Service Centers are staffed with trained
personnel to provide customers with efficient and reliable
product service.
Whether you need technical advice, repair, or genuine
factory replacement parts, contact the BLACK+DECKER
location nearest to you.
NOTE
fBLACK+DECKER’s policy is one of continuous
improvement to our products and, as such, we reserve
the right to change product specifications without prior
notice.
fStandard equipment and accessories may vary by
country.
fProduct specifications may differ by country.
fComplete product range may not be available in all
countries. Contact your local BLACK+DECKER
dealers for range availability.
ENGLISH •5
ENGLISH • 5
USE
Warning! Let the tool work at its own pace. Do not
overload.
Warning! Before drilling into walls, floors or ceilings,
check for the location of wiring and pipes.
Selecting the direction of rotation (Fig. E)
For drilling and for tightening screws, use forward
(clockwise) rotation. For loosening screws or removing a
jammed drill bit, use reverse (counterclockwise) rotation.
fTo select forward rotation, push the forward/reverse
slider (3) to the centre position.
fTo select reverse rotation, push the forward/reverse
slider to the left.
Warning! Never change the direction of rotation while
the motor is running.
Selecting the drilling mode
fFor drilling in masonry, set the drilling mode selector
(3) to the position.
fFor drilling in other materials and for screwdriving, set
the drilling mode selector to the position.
Setting the drilling depth (Fig. F)
fSlacken the side handle (7) by turning the grip
counterclockwise.
fSet the depth stop (6) to the desired position. The
maximum drilling depth is equal to the distance
between the tip of the drill bit and the front end of the
depth stop.
fTighten the side handle by turning the grip clockwise.
Switching on and off
fTo switch the tool on, press the speed switch (1).
For tools with variable speed switch, the tool speed
depends on how far you press the switch. As a
general rule, use low speeds for large diameter
drill bits and high speeds for smaller diameter drill bits.
fFor continuous operation, press the lock-on button (2)
and release the speed switch. This option is available
only at full speed. This option does not work in reverse
rotation. Reverse rotation available only for HD500.
fTo switch the tool off, release the speed switch.
To switch the tool off when in continuous operation,
press the speed switch once more and release it.
MAINTENANCE
Keep guards, air vents and the motor housing as clear as
possible of dust and dirt. Wipe with a clean cloth and blow
through with a low-pressure air supply. Excessive build-up
of metal dust can cause tracking of electrical current from
the internal parts to exposed metal parts.
Important! To assure product SAFETY and RELIABILITY,
repairs, maintenance and adjustment (other than those
listed in this manual) should be performed by authorized
service centers or other qualified service personnel,
always using identical replacement parts.
ACCESSORIES
Recommended accessories for use with your product
are available from your local dealer or authorized service
center.
PROTECTING THE ENVIRONMENT
Separate collection. This product must not be
disposed of with normal household waste.
Should you find one day that your
BLACK+DECKER product needs replacement, or
if it is of no further use to you, do not dispose of it
with household waste. Make this product available
for separate collection.
Separate collection of used products and packaging
allows materials to be recycled and used again.
Re-use of recycled materials helps prevent
environmental pollution and reduces the demand
for raw materials. Local regulations may provide for
separate collection of electrical products from the
household, at municipal waste sites or by the
retailer when you purchase a new product.
SERVICE INFORMATION
BLACK+DECKER offers a full network of company-owned
and authorized service locations throughtout Asia. All
BLACK+DECKER Service Centers are staffed with trained
personnel to provide customers with efficient and reliable
product service.
Whether you need technical advice, repair, or genuine
factory replacement parts, contact the BLACK+DECKER
location nearest to you.
NOTE
fBLACK+DECKER’s policy is one of continuous
improvement to our products and, as such, we reserve
the right to change product specifications without prior
notice.
fStandard equipment and accessories may vary by
country.
fProduct specifications may differ by country.
fComplete product range may not be available in all
countries. Contact your local BLACK+DECKER
dealers for range availability.
ENGLISH •5
ENGLISH • 5
USE
Warning! Let the tool work at its own pace. Do not
overload.
Warning! Before drilling into walls, floors or ceilings,
check for the location of wiring and pipes.
Selecting the direction of rotation (Fig. E)
For drilling and for tightening screws, use forward
(clockwise) rotation. For loosening screws or removing a
jammed drill bit, use reverse (counterclockwise) rotation.
fTo select forward rotation, push the forward/reverse
slider (3) to the centre position.
fTo select reverse rotation, push the forward/reverse
slider to the left.
Warning! Never change the direction of rotation while
the motor is running.
Selecting the drilling mode
fFor drilling in masonry, set the drilling mode selector
(3) to the position.
fFor drilling in other materials and for screwdriving, set
the drilling mode selector to the position.
Setting the drilling depth (Fig. F)
fSlacken the side handle (7) by turning the grip
counterclockwise.
fSet the depth stop (6) to the desired position. The
maximum drilling depth is equal to the distance
between the tip of the drill bit and the front end of the
depth stop.
fTighten the side handle by turning the grip clockwise.
Switching on and off
fTo switch the tool on, press the speed switch (1).
For tools with variable speed switch, the tool speed
depends on how far you press the switch. As a
general rule, use low speeds for large diameter
drill bits and high speeds for smaller diameter drill bits.
fFor continuous operation, press the lock-on button (2)
and release the speed switch. This option is available
only at full speed. This option does not work in reverse
rotation. Reverse rotation available only for HD500.
fTo switch the tool off, release the speed switch.
To switch the tool off when in continuous operation,
press the speed switch once more and release it.
MAINTENANCE
Keep guards, air vents and the motor housing as clear as
possible of dust and dirt. Wipe with a clean cloth and blow
through with a low-pressure air supply. Excessive build-up
of metal dust can cause tracking of electrical current from
the internal parts to exposed metal parts.
Important! To assure product SAFETY and RELIABILITY,
repairs, maintenance and adjustment (other than those
listed in this manual) should be performed by authorized
service centers or other qualified service personnel,
always using identical replacement parts.
ACCESSORIES
Recommended accessories for use with your product
are available from your local dealer or authorized service
center.
PROTECTING THE ENVIRONMENT
Separate collection. This product must not be
disposed of with normal household waste.
Should you find one day that your
BLACK+DECKER product needs replacement, or
if it is of no further use to you, do not dispose of it
with household waste. Make this product available
for separate collection.
Separate collection of used products and packaging
allows materials to be recycled and used again.
Re-use of recycled materials helps prevent
environmental pollution and reduces the demand
for raw materials. Local regulations may provide for
separate collection of electrical products from the
household, at municipal waste sites or by the
retailer when you purchase a new product.
SERVICE INFORMATION
BLACK+DECKER offers a full network of company-owned
and authorized service locations throughtout Asia. All
BLACK+DECKER Service Centers are staffed with trained
personnel to provide customers with efficient and reliable
product service.
Whether you need technical advice, repair, or genuine
factory replacement parts, contact the BLACK+DECKER
location nearest to you.
NOTE
fBLACK+DECKER’s policy is one of continuous
improvement to our products and, as such, we reserve
the right to change product specifications without prior
notice.
fStandard equipment and accessories may vary by
country.
fProduct specifications may differ by country.
fComplete product range may not be available in all
countries. Contact your local BLACK+DECKER
dealers for range availability.
ENGLISH •5
ENGLISH • 5
USE
Warning! Let the tool work at its own pace. Do not
overload.
Warning! Before drilling into walls, floors or ceilings,
check for the location of wiring and pipes.
Selecting the direction of rotation (Fig. E)
For drilling and for tightening screws, use forward
(clockwise) rotation. For loosening screws or removing a
jammed drill bit, use reverse (counterclockwise) rotation.
fTo select forward rotation, push the forward/reverse
slider (3) to the centre position.
fTo select reverse rotation, push the forward/reverse
slider to the left.
Warning! Never change the direction of rotation while
the motor is running.
Selecting the drilling mode
fFor drilling in masonry, set the drilling mode selector
(3) to the position.
fFor drilling in other materials and for screwdriving, set
the drilling mode selector to the position.
Setting the drilling depth (Fig. F)
fSlacken the side handle (7) by turning the grip
counterclockwise.
fSet the depth stop (6) to the desired position. The
maximum drilling depth is equal to the distance
between the tip of the drill bit and the front end of the
depth stop.
fTighten the side handle by turning the grip clockwise.
Switching on and off
fTo switch the tool on, press the speed switch (1).
For tools with variable speed switch, the tool speed
depends on how far you press the switch. As a
general rule, use low speeds for large diameter
drill bits and high speeds for smaller diameter drill bits.
fFor continuous operation, press the lock-on button (2)
and release the speed switch. This option is available
only at full speed. This option does not work in reverse
rotation. Reverse rotation available only for HD500.
fTo switch the tool off, release the speed switch.
To switch the tool off when in continuous operation,
press the speed switch once more and release it.
MAINTENANCE
Keep guards, air vents and the motor housing as clear as
possible of dust and dirt. Wipe with a clean cloth and blow
through with a low-pressure air supply. Excessive build-up
of metal dust can cause tracking of electrical current from
the internal parts to exposed metal parts.
Important! To assure product SAFETY and RELIABILITY,
repairs, maintenance and adjustment (other than those
listed in this manual) should be performed by authorized
service centers or other qualified service personnel,
always using identical replacement parts.
ACCESSORIES
Recommended accessories for use with your product
are available from your local dealer or authorized service
center.
PROTECTING THE ENVIRONMENT
Separate collection. This product must not be
disposed of with normal household waste.
Should you find one day that your
BLACK+DECKER product needs replacement, or
if it is of no further use to you, do not dispose of it
with household waste. Make this product available
for separate collection.
Separate collection of used products and packaging
allows materials to be recycled and used again.
Re-use of recycled materials helps prevent
environmental pollution and reduces the demand
for raw materials. Local regulations may provide for
separate collection of electrical products from the
household, at municipal waste sites or by the
retailer when you purchase a new product.
SERVICE INFORMATION
BLACK+DECKER offers a full network of company-owned
and authorized service locations throughtout Asia. All
BLACK+DECKER Service Centers are staffed with trained
personnel to provide customers with efficient and reliable
product service.
Whether you need technical advice, repair, or genuine
factory replacement parts, contact the BLACK+DECKER
location nearest to you.
NOTE
fBLACK+DECKER’s policy is one of continuous
improvement to our products and, as such, we reserve
the right to change product specifications without prior
notice.
fStandard equipment and accessories may vary by
country.
fProduct specifications may differ by country.
fComplete product range may not be available in all
countries. Contact your local BLACK+DECKER
dealers for range availability.
附件
建议与您的产品配套使用的附件可从当地经销商处
或授权服务中心另行购买。
保护环境
分类回收。本产品不得与普通家庭垃圾
一起处理。
如果您发现您的BLACK+DECKER产品需
要进行替换，或您已经不再需要使用这
些产品，请勿将它们与家庭废物一起处
理。请将它们单独分类回收。
分类回收使用过的产品和包装能够让材
料得以再循环和再利用。
再生材料的再利用有助于防止环境污染，
并降低对原材料的需求。当地法规可能
要求由市政废物处理点或向您出售新产
品的零售商提供从家庭中分类回收电气
产品的服务。
服务信息
BLACK+DECKER提供覆盖整个亚洲的公司隶属和授
权服务地点。所有的BLACK+DECKER服务中心都
具有训练有素的人员，为客户提供高效和可靠的产
品服务。
不论您是需要技术建议、维修或原厂替换部件，请
联系最靠近您的BLACK+DECKER地点。
注
► BLACK+DECKER的政策是持续改进我们的产
品，因此，我们保留随时更改产品规格的权利，
恕不另行通知。
► 标准设备和附件可能会因为不同的国家（地
区）而有所不同。
► 产品规格可能会因为不同的国家 / 地区而有所
不同。
► 并非所有国家 / 地区均可提供完整的产品系
列。有关各产品系列的供货情况，请联系您当
地的BLACK+DECKER代理商。
制造商 ：百得美国公司
地 址 ： 701 E Joppa Rd, TW050 MD21286, Towson, 美国
制造地 ：浙江武义
ENGLISH •5
ENGLISH • 5
USE
Warning! Let the tool work at its own pace. Do not
overload.
Warning! Before drilling into walls, floors or ceilings,
check for the location of wiring and pipes.
Selecting the direction of rotation (Fig. E)
For drilling and for tightening screws, use forward
(clockwise) rotation. For loosening screws or removing a
jammed drill bit, use reverse (counterclockwise) rotation.
fTo select forward rotation, push the forward/reverse
slider (3) to the centre position.
fTo select reverse rotation, push the forward/reverse
slider to the left.
Warning! Never change the direction of rotation while
the motor is running.
Selecting the drilling mode
fFor drilling in masonry, set the drilling mode selector
(3) to the position.
fFor drilling in other materials and for screwdriving, set
the drilling mode selector to the position.
Setting the drilling depth (Fig. F)
fSlacken the side handle (7) by turning the grip
counterclockwise.
fSet the depth stop (6) to the desired position. The
maximum drilling depth is equal to the distance
between the tip of the drill bit and the front end of the
depth stop.
fTighten the side handle by turning the grip clockwise.
Switching on and off
fTo switch the tool on, press the speed switch (1).
For tools with variable speed switch, the tool speed
depends on how far you press the switch. As a
general rule, use low speeds for large diameter
drill bits and high speeds for smaller diameter drill bits.
fFor continuous operation, press the lock-on button (2)
and release the speed switch. This option is available
only at full speed. This option does not work in reverse
rotation. Reverse rotation available only for HD500.
fTo switch the tool off, release the speed switch.
To switch the tool off when in continuous operation,
press the speed switch once more and release it.
MAINTENANCE
Keep guards, air vents and the motor housing as clear as
possible of dust and dirt. Wipe with a clean cloth and blow
through with a low-pressure air supply. Excessive build-up
of metal dust can cause tracking of electrical current from
the internal parts to exposed metal parts.
Important! To assure product SAFETY and RELIABILITY,
repairs, maintenance and adjustment (other than those
listed in this manual) should be performed by authorized
service centers or other qualified service personnel,
always using identical replacement parts.
ACCESSORIES
Recommended accessories for use with your product
are available from your local dealer or authorized service
center.
PROTECTING THE ENVIRONMENT
Separate collection. This product must not be
disposed of with normal household waste.
Should you find one day that your
BLACK+DECKER product needs replacement, or
if it is of no further use to you, do not dispose of it
with household waste. Make this product available
for separate collection.
Separate collection of used products and packaging
allows materials to be recycled and used again.
Re-use of recycled materials helps prevent
environmental pollution and reduces the demand
for raw materials. Local regulations may provide for
separate collection of electrical products from the
household, at municipal waste sites or by the
retailer when you purchase a new product.
SERVICE INFORMATION
BLACK+DECKER offers a full network of company-owned
and authorized service locations throughtout Asia. All
BLACK+DECKER Service Centers are staffed with trained
personnel to provide customers with efficient and reliable
product service.
Whether you need technical advice, repair, or genuine
factory replacement parts, contact the BLACK+DECKER
location nearest to you.
NOTE
fBLACK+DECKER’s policy is one of continuous
improvement to our products and, as such, we reserve
the right to change product specifications without prior
notice.
fStandard equipment and accessories may vary by
country.
fProduct specifications may differ by country.
fComplete product range may not be available in all
countries. Contact your local BLACK+DECKER
dealers for range availability.
ENGLISH •5
ENGLISH • 5
USE
Warning! Let the tool work at its own pace. Do not
overload.
Warning! Before drilling into walls, floors or ceilings,
check for the location of wiring and pipes.
Selecting the direction of rotation (Fig. E)
For drilling and for tightening screws, use forward
(clockwise) rotation. For loosening screws or removing a
jammed drill bit, use reverse (counterclockwise) rotation.
fTo select forward rotation, push the forward/reverse
slider (3) to the centre position.
fTo select reverse rotation, push the forward/reverse
slider to the left.
Warning! Never change the direction of rotation while
the motor is running.
Selecting the drilling mode
fFor drilling in masonry, set the drilling mode selector
(3) to the position.
fFor drilling in other materials and for screwdriving, set
the drilling mode selector to the position.
Setting the drilling depth (Fig. F)
fSlacken the side handle (7) by turning the grip
counterclockwise.
fSet the depth stop (6) to the desired position. The
maximum drilling depth is equal to the distance
between the tip of the drill bit and the front end of the
depth stop.
fTighten the side handle by turning the grip clockwise.
Switching on and off
fTo switch the tool on, press the speed switch (1).
For tools with variable speed switch, the tool speed
depends on how far you press the switch. As a
general rule, use low speeds for large diameter
drill bits and high speeds for smaller diameter drill bits.
fFor continuous operation, press the lock-on button (2)
and release the speed switch. This option is available
only at full speed. This option does not work in reverse
rotation. Reverse rotation available only for HD500.
fTo switch the tool off, release the speed switch.
To switch the tool off when in continuous operation,
press the speed switch once more and release it.
MAINTENANCE
Keep guards, air vents and the motor housing as clear as
possible of dust and dirt. Wipe with a clean cloth and blow
through with a low-pressure air supply. Excessive build-up
of metal dust can cause tracking of electrical current from
the internal parts to exposed metal parts.
Important! To assure product SAFETY and RELIABILITY,
repairs, maintenance and adjustment (other than those
listed in this manual) should be performed by authorized
service centers or other qualified service personnel,
always using identical replacement parts.
ACCESSORIES
Recommended accessories for use with your product
are available from your local dealer or authorized service
center.
PROTECTING THE ENVIRONMENT
Separate collection. This product must not be
disposed of with normal household waste.
Should you find one day that your
BLACK+DECKER product needs replacement, or
if it is of no further use to you, do not dispose of it
with household waste. Make this product available
for separate collection.
Separate collection of used products and packaging
allows materials to be recycled and used again.
Re-use of recycled materials helps prevent
environmental pollution and reduces the demand
for raw materials. Local regulations may provide for
separate collection of electrical products from the
household, at municipal waste sites or by the
retailer when you purchase a new product.
SERVICE INFORMATION
BLACK+DECKER offers a full network of company-owned
and authorized service locations throughtout Asia. All
BLACK+DECKER Service Centers are staffed with trained
personnel to provide customers with efficient and reliable
product service.
Whether you need technical advice, repair, or genuine
factory replacement parts, contact the BLACK+DECKER
location nearest to you.
NOTE
fBLACK+DECKER’s policy is one of continuous
improvement to our products and, as such, we reserve
the right to change product specifications without prior
notice.
fStandard equipment and accessories may vary by
country.
fProduct specifications may differ by country.
fComplete product range may not be available in all
countries. Contact your local BLACK+DECKER
dealers for range availability.