Black & Decker BWDS User manual

INSTRUCTION MANUAL
WASHER DRYER STAND
Thank you for choosing BLACK+DECKER!
PLEASE READ BEFORE RETURNING THIS PRODUCT FOR
ANY REASON.
If you have a question or experience a problem with your BLACK+DECKER
purchase, go to www.blackanddecker.com/instantanswers
If you can’t find the answer or do not have access to the Internet, call
844-299-0879 from 10:30 a.m. to 6:30 p.m. EST Mon. - Fri. to speak with an
agent. Please have the catalog number available when you call.
SAVE THIS MANUAL FOR FUTURE REFERENCE.
CATALOG NUMBER
BWDS

Page 2
Thank you for purchasing our
BLACK+DECKER product. This
easy-to-use manual will guide you
in getting the best use of your
washer dryer stand.
Remember to record the model and
serial numbers. They are on a label
on the rear.
Staple your receipt to your manual. You will need it to obtain warranty service.
Model number
Serial number
Date of purchase
PRODUCT REGISTRATION
CONTENTS
SAFETY INFORMATION
Important Safety Instructions.............................................................................................................................................. 2
SET UP & USE
Parts List....................................................................................................................................................................................3-4
Assembly Instructions.......................................................................................................................................5-9
CLEANING & CARE.............................................................................................................................................. 10
TROUBLE SHOOTING & WARRANTY
Customer Service.................................................................................................................................................. 10
Limited Warranty .....................................................................................................................................................................11
SAFETY INFORMATION
IMPORTANT SAFETY INSTRUCTIONS
1. READ ALL INSTRUCTIONS BEFORE USE
SAVE THESE INSTRUCTIONS
HOUSEHOLD USE ONLY
WARNING:
• Maximum Weight for Dryer Rack 100 lbs. Do not exceed maximum
weight limit.
• This dryer must be anchored to a wall using anti-tip
brackets to avoid tipping.
• Some assembly parts may cause choking. Keep away from children.
• Do not lean on, or allow children to play or climb on the washer dryer
stand. Do not allow children to hang from the door of the dryer when
seated on the top of the washer dryer stand because this could cause
tipping.

Page 3
SET UP & USE
PARTS LIST
Tools Required: Screwdriver and Drill

Page 4Page 4
SET UP & USE
ID DESCRIPTION QUANTITY
A LEFT DRYER SUPPORT 1
A1 RIGHT DRYER SUPPORT 1
A2 NON-SLIP PAD 4
B LEFT BASE 1
B1 RIGHT BASE 1
C UPPER LEFT FRONT VERTICAL POLE 1
C1 UPPER RIGHT FRONT VERTICAL POLE 1
D UPPER LEFT REAR VERTICAL POLE 1
D1 UPPER RIGHT REAR VERTICAL POLE 1
E LOWER LEFT REAR VERTICAL POLE 1
E1 LOWER RIGHT REAR VERTICAL POLE 1
F LOWER LEFT FRONT VERTICAL POLE 1
F1 LOWER RIGHT FRONT VERTICAL POLE 1
G HORIZONTAL SUPPORT BEAMS 3
H ANTI-TIP BRACKET 2
I CONNECTING RAIL 2
J DIAGONAL SUPPORT RAIL 2
K LONG BOLTS 6
L SHORT BOLTS 4
M SCREWS 12
N BUTTERFLY NUT 10
O DRYWALL SCREWS WITH ANCHOR 2 sets

Page 5
SET UP & USE
ASSEMBLY INSTRUCTIONS
1. Using the diagram below as reference to position the poles, INSERT E (LOWER
LEFT REAR VERTICAL POLE) and F (LOWER LEFT FRONT VERTICAL POLE) into
B LEFT BASE.
Use (1) M (SCREW) to secure on each side.
2. Insert D (UPPER LEFT REAR VERTICAL POLE) into E (LOWER LEFT FRONT
VERTICAL POLE).
Insert C (UPPER LEFT FRONT VERTICAL POLE) into F (LOWER LEFT FRONT
VERTICAL POLE), Line up I (CONNECTING RAIL) with the holes on the front and
rear poles as shown and secure using (1) M (SCREW) on each side.

Page 6
SET UP & USE
3. Align A (LEFT DRYER SUPPORT) and insert into C (UPPER LEFT FRONT
VERTICAL POLE) and D (UPPER LEFT REAR VERTICAL POLE), use (1) M (screw)
on each side to secure.
Follow the same steps to assemble the right side:
INSERT E1 (LOWER RIGHT REAR VERTICAL POLE) and F1 (LOWER RIGHT
FRONT VERTICAL POLE) into B1 RIGHT BASE. Use (1) M (SCREW) to secure on
each side.
Insert D1 (UPPER RIGHT REAR VERTICAL POLE) into E1 (LOWER RIGHT REAR
VERTICAL POLE).
Insert C1 (UPPER RIGHT FRONT VERTICAL POLE) into F1 (LOWER RIGHT FRONT
VERTICAL POLE),
Line up I (CONNECTING RAIL) with the holes on the front and rear poles as
shown and secure using (1) M (SCREW) on each side.
Align A1 (RIGHT DRYER SUPPORT) and insert into C1 (UPPER RIGHT FRONT
VERTICAL POLE) and D1 (UPPER RIGHT REAR VERTICAL POLE), use (1) M
(SCREW) on each side to secure.
C
AA1
D1
E1 F1
B1
C1
Left side Right side
D
II
B
EF

Page 7
4. Attach G (HORIZONTAL SUPPORT BEAMS) to the top and bottom of the left rear
pole and the top of the left front pole as shown.
Insert K (LONG BOLT) through the holes of the pole and N (BUTTERFLY NUT) on
the opposite side of the pole. Turn the BUTTERFLY NUT clockwise to secure but
do not tighten completely.
5. Secure the right side with K (LONG BOLTS) and N (BUTTERFLY NUT), but do not
tighten completely.
N
SET UP & USE
K
N

Page 8
6. Align the holes in H (ANTI-TIP BRACKET), J (DIAGONAL SUPPORT RAIL) and D
(UPPER LEFT REAR VERTICAL POLE) as shown. The other end of J (DIAGONAL
SUPPORT RAIL) should be attached to E1 (LOWER RIGHT REAR VERTICAL
POLE).
Insert L (Short bolt) through the hole in H (ANTI-TIP BRACKET) first to secure
with N (butterfly nut) on the opposite side.
7. Align the holes in H (ANTI-TIP BRACKET), J (DIAGONAL SUPPORT RAIL)
and D1 (UPPER RIGHT REAR VERTICAL POLE) as shown. The other end of J
(DIAGONAL SUPPORT RAIL) should be attached to E (LOWER LEFT REAR
VERTICAL POLE).
Use N (butterflynut) and L (Short bolts) to secure.
SET UP & USE
E1
D
Butterfly Nut
D1 D
HH
J
J
E1 E

Page 9
SET UP & USE
8. Tighten all the screws and butterfly nuts and move the stand to where you intend
to attach it to the wall.
9. Mark the position on the wall where the holes on H (ANTI-TIP BRACKET) will
connect to the wall to mark the location of O (DRYWALL SCREWS WITH
ANCHOR). Drill a hole in the wall slightly smaller than the diameter of the plastic
wall anchor. Insert the wall anchor securely into the hole so the plastic anchor is
flush with the wall. Using a Philips head screwdriver, insert the screw through the
hole in the H (ANTI-TIP BRACKET) and into the plastic anchor.
10. Place A2 (NON-SLIP PAD) on both A (LEFT DRYER SUPPORT) and A1 (RIGHT
DRYER SUPPORT).
A2 A2
A2 A2

Page 10
CLEANING AND MAINTENANCE
Use water or a mild soap and water solution to clean your washer dryer stand. Do not
use abrasive cleaners which may scratch the surface.
SET UP & USE
TROUBLESHOOTING & WARRANTY
IMPORTANT
DO NOT RETURN THIS PRODUCT TO THE STORE
If you have a problem with this product, please contact the
BLACK+DECKER Customer Satisfaction Center at
844-299-0879 or [e-mail].
DATED PROOF OF PURCHASE, MODEL # AND SERIAL #
REQUIRED FOR WARRANTY SERVICE

Page 11Page 11
TROUBLESHOOTING & WARRANTY
LIMITED WARRANTY
Any repair, replacement, or warranty service,
and all questions about this product should be
directed to BLACK+DECKER at 844-299-0879
from the USA or Puerto Rico.
BLACK+DECKER warrants to the original purchaser
that the product will be free from defects in material,
parts and workmanship for the period designated for
this product. The warranty commences the day the
product is purchased and covers up to a period of
1 year (12 months) for labor/1 year (12 months) for
parts (manufacturing defects only). BLACK+DECKER
agrees that it will, at its option, replace the defective
product with either a new or remanufactured unit
equivalent to your original purchase during the
warranty period.
Exclusions: This warranty does not apply to the
below:
1. If the appearance or exterior of
the product has been damaged or
defaced, altered or modified in design or
construction.
2. If the product original serial number
has been altered or removed or cannot
be readily determined.
3. If there is damaged due to power line
surge, user damage to the AC power
cord or connection to improper voltage
source.
4. If damage is due to general misuse,
accidents or acts of God.
5. If repair attempts are done by
unauthorized service agents, use of
parts other than genuine parts or parts
obtained from persons other than
authorized service companies.
6. On units that have been transferred
from the original owner.
7. On products that have been purchased
as refurbished, like new, second-hand, in
a “As-Is” or “Final Sale” terms.
8. To products used in a commercial or
rental setting.
9. To products used in settings other than
ordinary household use or used other
than in accordance with the provided
instructions.
10. To damages for service calls for
improper installations.
11. Transportation and shipping costs
associated with the replacement of the
unit.
12. Service calls to instruct you how to use
your product.
13. Service calls to repair or replace the
house fuse, reset the circuit breaker or
correct the wiring in the house.
REPAIR OR REPLACEMENT AS PROVIDED UNDER
THIS WARRANTY IS THE EXCLUSIVE REMEDY OF
THE CUSTOMER; BLACK+DECKER. SHALL NOT BE
LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL
DAMAGES FOR BREACH OF ANY EXPRESS OR
IMPLIED WARRANTY ON THIS PRODUCT, EXCEPT
TO THE EXTENT PROHIBITED BY APPLICABLE LAW.
ANY IMPLIED WARRANTY OF MERCHANTABILITY
OF FITNESS FOR A PARTICULAR PURPOSE ON THIS
PRODUCT IS LIMITED TO THE DURATION OF THE
WARRANTY.
Some states do not allow the exclusion or limitations
of incidental or consequential damages, or limitations
on how long the warranty lasts. In these cases the
above exclusions or limitations may not apply to you.
This warranty gives you specific legal rights and you
may also have other rights which vary from state to
state.
Obtaining Service: To obtain service, product
literature, supplies or accessories please call
844-299-0879 to create a ticket for exchange/repair.
Please make sure to provide the date of purchase,
model number and a brief description of the problem.
Our customer service representative
will contact you or send detailed return instructions.
BLACK+DECKER does not warrant that the appliance will work
properly in all environmental conditions, and makes no warranty
and representation, either implied or expressed, with respect
to the quality, performance, merchantability, or fitness for a
particular purpose other than the purpose identified within this
user’s manual. BLACK+DECKER has made every eort to ensure
that this user’s manual is accurate and disclaims liability for any
inaccuracies or omissions that may have occurred. Information in
this user’s manual is subject to change without notice and does
not represent a commitment on the part of BLACK+DECKER.
BLACK+DECKER reserves the right to make improvements to
this user’s manual and/or to the products described in this user’s
manual at any time without notice. If you find information in this
manual that is incorrect, misleading, or incomplete, please contact
us at 844-299-0879.
W Appliance Co.
1356 Broadway
New York, NY 10018

Page 12 Page 12Page 12
BLACK & DECKER, BLACK+DECKER, the BLACK & DECKER and
BLACK+DECKER logos and product names and the orange and black color
scheme are trademarks of The Black & Decker Corporation, used under license.
All rights reserved.
Product in this box may differ slightly from that pictured. Does not affect
function. Not all accessories shown in photography are included in this
package.
Imported by W Appliance, Inc., 1356 Broadway, New York, NY 10018
September 2020 Printed in China
51.2”
21.3”
24.4”
Fits Portable Dryers Maximum Weight of 100 lbs.
21.3”
19.5”
22.2”
21.2”