Black & Decker BWDS User manual

Page 1
INSTRUCTION MANUAL
WASHER DRYER STAND
Thank you for choosing BLACK+DECKER!
PLEASE READ BEFORE RETURNING THIS PRODUCT FOR ANY
REASON.
If you have a question or experience a problem with your BLACK+DECKER
purchase, go to www.blackanddecker.com/instantanswers
If you can’t find the answer or do not have access to the Internet, call
844-299-0879 from 10:30 a.m. to 6:30 p.m. EST Mon.-Fri. to speak with an
agent. Please have the catalog number available when you call.
SAVE THIS MANUAL FOR FUTURE REFERENCE.
CATALOG NUMBER
BWDS

Page 2
Thank you for purchasing our
BLACK+DECKER product. This
easy-to-use manual will guide you
in getting the best use of your
washer dryer stand.
Remember to record the model and
serial numbers. They are on a label
on the rear.
Staple your receipt to your manual. You will need it to obtain warranty service.
Model number
Serial number
Date of purchase
SAFETY INFORMATION
Important Safety Instructions.............................................................................................................................................. 3
SET UP & USE
Parts List.................................................................................................................................................................................... 4-6
Assembly Instructions........................................................................................................................................7-17
CLEANING & CARE..............................................................................................................................................18
TROUBLESHOOTING & WARRANTY
Important ...................................................................................................................................................................18
Limited Warranty......................................................................................................................................................................19
CONTENTS
PRODUCT REGISTRATION

Page 3
1. READ ALL INSTRUCTIONS BEFORE USE.
WARNING:
• Maximum Weight for Dryer Rack 60 lbs. Do not exceed maximum weight limit.
• This washer dryer stand must be anchored to a wall using anti-tip brackets to
avoid tipping.
RISK OF PERSONAL INJURY OR DEATH. THE STAND MUST BE SECURED TO
RIGID FRAMING MEMBER OF ADJACENT WALL BEFORE USING.
• Some assembly parts may cause choking. Keep away from children.
• Do not lean on, or allow children to play or climb on the washer dryer stand. Do not
allow children to hang from the door of the dryer when seated on the top of the
washer dryer stand because this could cause tipping.
SAVE THESE INSTRUCTIONS
HOUSEHOLD USE ONLY
WARNING
When using the washer dryer stand , basic safety precautions
should be followed, including the following:
DANGER
DANGER - Immediate hazards
that WILL result in severe
personal injury or death
WARNING
WARNING - Hazards or unsafe
practices that COULD result in
severe personal injury or death
CAUTION
CAUTION - Hazards or unsafe
practices that COULD result in
minor personal injury
IMPORTANT SAFETY INSTRUCTIONS
SAFETY INFORMATION

Page 4
PARTS LIST
Tools Required: Screwdriver and Drill.
NOTE:
15S = 2 short butterfly screws. Used for installing Support Rails, to L-BP and R-BP
pieces. Must be inserted so that wing is on exterior side of unit.
25S = 14 short buttery screws. Used for installing Connecting Rails, L-BP and R-BP
pieces to vertical rails. Must be inserted so that wing is on exterior side of unit.
35M = 4 medium buttery screws. Connects diagonal support rails. Must be inserted
so that wing is on rear of unit.
45L = 6 long buttery screws. Must be inserted through vertical rail rst then
tightened into Reinforcing Bars.
SET UP & USE
25S
25S
25S
15S
25S
25S
25S
25S
15S
Anti-tip Bracket
Connecting Rail
Connecting Rail
Anti-tip Bracket
35M
35M
35M
35M
25S
45L
45L
45L
LF1-1
RF1-1
RB2-1
LB2-1
LF1-2
RF1-2
L-BP
R-BP
RB2-2
LB2-2
L-BP R-BP
Reinforcing Bar
Reinforcing Bar
Support Rail
Support Rail

Page 5
L-BP R-BP R-BP
L-BP
SET UP & USE
Diagonal Support Rail
Connecting Rail
Support Rail
Anti-tip Bracket
Lag Type Screws
Reinforcing Bar
35M 45L25S15S
Non-slip Pad
LF1-1 RF1-1
RB2-1 LB2-1
LB2-2 RB2-2
LF1-2 RF1-2

Page 6
SET UP & USE
ID DESCRIPTION QUANTITY
L-BP LEFT DRYER SUPPORT 1
R-BP RIGHT DRYER SUPPORT 1
NON-SLIP PAD 4
L-BP LEFT BASE PLATE 1
R-BP RIGHT BASE PLATE 1
LF1-1 UPPER LEFT FRONT VERTICAL POLE 1
RF1-1 UPPER RIGHT FRONT VERTICAL POLE 1
LB2-1 UPPER LEFT BACK VERTICAL POLE 1
RB2-1 UPPER RIGHT BACK VERTICAL POLE 1
LB2-2 LOWER LEFT BACK VERTICAL POLE 1
RB2-2 LOWER RIGHT BACK VERTICAL POLE 1
LF1-2 LOWER LEFT FRONT VERTICAL POLE 1
RF1-2 LOWER RIGHT FRONT VERTICAL POLE 1
REINFORCING BARS 3
ANTI-TIP BRACKET 2
CONNECTING RAIL 2
SUPPORT RAIL 2
DIAGONAL SUPPORT RAIL 1
45L BUTTERFLY SCREWS (Long)-45mm 6
35M BUTTERFLY SCREWS (Medium)-35mm 4
25S BUTTERFLY SCREWS (Short)-25mm 14
15S BUTTERFLY SCREWS (Short)-15mm 2
LAG TYPE SCREWS 2
Parts are labeled according to the ID in the above Chart. ID number is stamped on the
top of the vertical poles. The DOWN arrow indicates lower parts and the UP arrow
indicates upper parts.
NOTE: There are 4 sizes of butterfly screws. It is important to use the correct screw
(45L, 35M, 25S, 15S) and insert in the location as directed in the instructions.
To install the butterfly screw, insert and turn to the right until the entire threaded part
of the screw is fully inserted.

Page 7
SET UP & USE
ASSEMBLY INSTRUCTIONS
1. Using the diagram below as reference to position the poles, INSERT LB2-2
(LOWER LEFT BACK VERTICAL POLE) and LF1-2 (LOWER LEFT FRONT
VERTICAL POLE) into L-BP LEFT BASE. The base of the poles should be
positioned between the L-BP slots and aligned with the holes.
Use 25S (BUTTERFLY SCREW) to secure on each side. They should be inserted
from the outside of L-BP and inserted fully through the holes of the poles to
secure.
NOTE: Follow the same steps to assemble the right side.
2. Insert LB2-1 (UPPER LEFT BACK VERTICAL POLE) into LB2-2 (LOWER LEFT
BACK VERTICAL POLE).
Insert LF1-1 (UPPER LEFT FRONT VERTICAL POLE) into LF1-2 (LOWER LEFT
FRONT VERTICAL POLE).
LF1-2
LB2-2
L-BP
25S
Closeup of LF1-2 and
LB2-2 being inserted into
L-BP . Make sure holes are
aligned when inserted.
LB2-2
25S
LF1-2
L-BP
LB2-1
LB2-2
LF1-2
LF1-1

Page 8
SET UP & USE
Line up the holes of one side of a SUPPORT RAIL, then the CONNECTING RAIL with
the holes on the exterior side of LF1-1 (UPPER LEFT FRONT VERTICAL POLE)
and LB2-1 (UPPER LEFT BACK VERTICAL POLE). Secure with 25S (BUTTERFLY
SCREW).
Line up the middle hole of the SUPPORT RAIL with the hole on the outside of LF1-2
(LOWER LEFT FRONT VERTICAL POLE), Secure with 25S (BUTTERFLY SCREW).
Line up the last hole of the SUPPORT RAIL with the hole on the outside of L-BP
(LEFT BASE), Secure with 15S (BUTTERFLY SCREW).
NOTE: Follow the same steps to assemble the right side.
25S
15S
L-BP
Support Rail
Support Rail
25S
Connecting Rail
Support Rail
25S
LF1-1
LB2-1
LF1-2

Page 9
3. Attach REINFORCING BARS to the top and bottom of the left BACK pole and the
top of the LF1-1 as shown below.
Attach one side of a REINFORCING BAR to LB2-1 . Align the holes and Insert 45L
(BUTTERFLY SCREW) through LB2-1 first and then through the reinforcing bar.
Attach one side of a REINFORCING BAR to LF1-1 . Align the holes and Insert 45L
(BUTTERFLY SCREW) through LF1-1 rst and then through the reinforcing bar.
Attach one side of the remaining REINFORCING BAR to LB2-2 . Align the holes
and Insert 45L (BUTTERFLY SCREW) through LB2-2 rst and then through the
reinforcing bar.
SET UP & USE
REINFORCING BAR
REINFORCING BAR
45L
45L
LB2-1
LB2-2
LF1-1
NOTE: The wings of 45L screw must keep vertical rather than horizontal so it does
not obstruct the installation of the DRYER SUPPORT.
45L
CORRECT INCORRECT

Page 10
Follow the same steps to assemble the right side:
Attach another side of a REINFORCING BAR to RB2-1 . Align the holes and Insert
45L (BUTTERFLY SCREW) through RB2-1 first and then through the reinforcing bar.
Attach another side of a REINFORCING BAR to RF1-1 . Align the holes and Insert
45L (BUTTERFLY SCREW) through RF1-1 rst and then through the reinforcing bar.
Attach one side of the remaining REINFORCING BAR to RB2-2 . Align the holes
and Insert 45L (BUTTERFLY SCREW) through RB2-2 rst and then through the
reinforcing bar.
RB2-1
RB2-2
RF1-1
SET UP & USE

Page 11
SET UP & USE
4. Align L-BP (LEFT DRYER SUPPORT) and insert into LF1-1 (UPPER LEFT FRONT
VERTICAL POLE) and LB2-1 (UPPER LEFT BACK VERTICAL POLE). Use 25S
screws to secure poles onto support. Make sure 25S screws are inserted with the
butterfly wing on the exterior side of the unit.
Follow the same steps to assemble the right side:
Align R-BP (RIGHT DRYER SUPPORT) and insert into RF1-1 (UPPER RIGHT FRONT
VERTICAL POLE) and RB2-1 (UPPER RIGHT BACK VERTICAL POLE). Use 25S
screws to secure poles onto support. Make sure 25S screws are inserted with the
butterfly wing on the exterior side of the unit.
LEFT SIDE RIGHT SIDE
25S
L-BP R-BP
LF1-1
RF1-1
LB2-1
RB2-1
LF1-2 RF1-2
LB2-2
RB2-2
L-BP
R-BP
Connecting Rail
Connecting Rail
Support Rail
Support Rail
Reinforcing Bar
Reinforcing Bar
LB2-1
LF1-1
L-BP
25S
25S
LB2-1
LF1-1
L-BP
25S
25S

Page 12
SET UP & USE
5. Align the holes in the DIAGONAL SUPPORT RAIL, LB2-1 (UPPER LEFT
BACK VERTICAL POLE) and ANTI-TIP BRACKET as shown below. Insert 35M
(BUTTERFLY SCREW) into the ANTI-TIP BRACKET and insert all the way through
the DIAGONAL SUPPORT RAIL and LB2-1 (UPPER LEFT BACK VERTICAL
POLE).
Align the holes in the DIAGONAL SUPPORT RAIL, RB2-1 (UPPER RIGHT BACK
VERTICAL POLE) and ANTI-TIP BRACKET as shown. Insert 35M (BUTTERFLY
SCREW) into the ANTI-TIP BRACKET and insert all the way through the
DIAGONAL SUPPORT RAIL and RB2-1 (UPPER RIGHT BACK VERTICAL POLE).
Installation Sequence
Step1: Add Diagonal support rail.
Step2: Add Anti-tip brackets.
Diagonal Support Rail.
Anti-tip brackets
LB2-1 Step3: Insert 35M screws.
Insert 35M screws
ANTI-TIP
BRACKET
35M
RB2-1
LB2-1
RB2-2
LB2-2

Page 13
SET UP & USE
6. Align the holes on the bottom of the DIAGONAL SUPPORT RAIL and
LB2-2 (LOWER LEFT BACK VERTICAL POLE) as shown below. Insert 35M
(BUTTERFLY SCREW) through the DIAGONAL SUPPORT RAIL and LB2-2
(LOWER LEFT BACK VERTICAL POLE).
Align the holes on the bottom of the DIAGONAL SUPPORT RAIL and RB2-2
(LOWER RIGHT BACK VERTICAL POLE) as shown below. Insert 35M (BUTTERFLY
SCREW) through the DIAGONAL SUPPORT RAIL and RB2-2 (LOWER RIGHT
BACK VERTICAL POLE).
ANTI-TIP BRACKETS
RB2-1
LB2-1
RB2-2
LB2-2

Page 14
SET UP & USE
7. Tighten all the BUTTERFLY SCREWS and move the stand to where you intend to
attach it to the wall.
8. Mark the position on the wall where the holes of the ANTI-TIP BRACKET will
connect to the wall.
WARNING: To reduce the likelihood of injury or property damage, the anti tip
feature must be properly installed and utilized.
WARNING:
Suitable lag type screws (included) will need to be used to properly anchor the
washer dryer stand to a rigid framing member. Rigid framing members could include
wood or metal studs and concrete blocks. If screwed into a wood framing member
using lag screws with a minimum diameter of 1/4” and 1-1/2” in length, mounting one
bracket on a wall stud will be sucient.
Before drilling or screwing, verify that there are no electric cables, plumbing pipes or
other potential hazards behind the wall where the lag screws are being installed.
ANTI-TIP BRACKETS

Page 15
NON-SLIP PAD NON-SLIP PAD
BOTTOM VIEW OF DRYER
SET UP & USE
9. Place NON-SLIP PADS on the base of the dryer as illustrated below. Make sure to
place NON-SLIP PADS where they will rest on the Dryer Rack to avoid slipping.
Remove the feet on the bottom of the dryer.
Place dryer on top of the rack.
WARNING: Dryer stand should only be used with dryers that have a flat
base or removable feet or legs. Do not remove dryer feet against
manufacturer recommendation.

Page 16
SET UP & USE
TIGHTEN
For Black + Decker dryer models BCED27 and BCED37 position the dryer so the
holes of the dryer from the feet are aligned with the back holes of the top of the
dryer rack L-BP (LEFT DRYER SUPPORT) and R-BP (RIGHT DRYER SUPPORT).
Re-install the feet through the holes so the dryer is now anchored directly to the
dryer stand.
For dryers that are not Black + Decker brand, you can also secure one or more of
the feet through the back holes. If the dryer does not have removable feet or the
holes are not aligned with the holes on L-BP (LEFT DRYER SUPPORT) and R-BP
(RIGHT DRYER SUPPORT), the dryer can rest on top.
Insert Feet
Insert Feet
L-BP
R-BP

Page 17
10. Place the washer so the legs sit on L-BP LEFT BASE and R-BP RIGHT BASE.
SET UP & USE

Page 18
CLEANING & CARE
CLEANING AND MAINTENANCE
Use water or a mild soap and water solution to clean your washer dryer stand. Do not
use abrasive cleaners which may scratch the surface.
TROUBLESHOOTING & WARRANTY
IMPORTANT
DO NOT RETURN THIS PRODUCT TO THE STORE
If you have a problem with this product, please contact the
BLACK+DECKER Customer Satisfaction Center at
844-299-0879 or [e-mail].
DATED PROOF OF PURCHASE, MODEL # AND SERIAL #
REQUIRED FOR WARRANTY SERVICE

Page 19
TROUBLESHOOTING & WARRANTY
LIMITED WARRANTY
Any repair, replacement, or warranty service,
and all questions about this product should be
directed to W Appliance Co. at 844-299-0879
from the USA or Puerto Rico.
W Appliance warrants to the original purchaser that
the product will be free from defects in material,
parts and workmanship for the period designated for
this product. The warranty commences the day the
product is purchased and covers up to a period of
1 year (12 months) for labor/1 year (12 months) for
parts (manufacturing defects only). W Appliance
agrees that it will, at its option, replace the defective
product with either a new or remanufactured unit
equivalent to your original purchase during the
warranty period.
Exclusions: This warranty does not apply to the
below:
1. If the appearance or exterior of
the product has been damaged or
defaced, altered or modified in design or
construction.
2. If the product original serial number
has been altered or removed or cannot
be readily determined.
3. If there is damaged due to power line
surge, user damage to the AC power
cord or connection to improper voltage
source.
4. If damage is due to general misuse,
accidents or acts of God.
5. If repair attempts are done by
unauthorized service agents, use of
parts other than genuine parts or parts
obtained from persons other than
authorized service companies.
6. On units that have been transferred
from the original owner.
7. On products that have been purchased
as refurbished, like new, second-hand, in
a “As-Is” or “Final Sale” terms.
8. To products used in a commercial or
rental setting.
9. To products used in settings other than
ordinary household use or used other
than in accordance with the provided
instructions.
10. To damages for service calls for
improper installations.
11. Transportation and shipping costs
associated with the replacement of the
unit.
12. Service calls to instruct you how to use
your product.
13. Service calls to repair or replace the
house fuse, reset the circuit breaker or
correct the wiring in the house.
REPAIR OR REPLACEMENT AS PROVIDED UNDER
THIS WARRANTY IS THE EXCLUSIVE REMEDY OF
THE CUSTOMER; W APPLIANCE. SHALL NOT BE
LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL
DAMAGES FOR BREACH OF ANY EXPRESS OR
IMPLIED WARRANTY ON THIS PRODUCT, EXCEPT
TO THE EXTENT PROHIBITED BY APPLICABLE LAW.
ANY IMPLIED WARRANTY OF MERCHANTABILITY
OF FITNESS FOR A PARTICULAR PURPOSE ON THIS
PRODUCT IS LIMITED TO THE DURATION OF THE
WARRANTY.
Some states do not allow the exclusion or limitations
of incidental or consequential damages, or limitations
on how long the warranty lasts. In these cases the
above exclusions or limitations may not apply to you.
This warranty gives you specific legal rights and you
may also have other rights which vary from state to
state.
Obtaining Service: To obtain service, product
literature, supplies or accessories please call
844-299-0879 to create a ticket for exchange/repair.
Please make sure to provide the date of purchase,
model number and a brief description of the problem.
Our customer service representative will contact you
or send detailed return instructions.
W Appliance does not warrant that the appliance will work
properly in all environmental conditions, and makes no warranty
and representation, either implied or expressed, with respect
to the quality, performance, merchantability, or fitness for a
particular purpose other than the purpose identified within this
user’s manual. W Appliance has made every eort to ensure
that this user’s manual is accurate and disclaims liability for any
inaccuracies or omissions that may have occurred. Information in
this user’s manual is subject to change without notice and does
not represent a commitment on the part of W Appliance.
W Appliance reserves the right to make improvements to this
user’s manual and/or to the products described in this user’s
manual at any time without notice. If you find information in this
manual that is incorrect, misleading, or incomplete, please contact
us at 844-299-0879.
W Appliance Co.
1356 Broadway
New York, NY 10018

Page 20Page 20
Fits Portable Dryers Maximum Weight of 60 lbs.
WARNING:
This washer dryer stand is suitable for BLACK+DECKER portable dryers BCED26
and BCED37.
It can also be used with any portable/compact dryers with a maximum depth of
21.4”, a minimum width of 24.6” with a flat base or removable feet or legs. Do not
remove dryer feet against manufacturer recommendation.
The weight should not exceed 60 lbs.
This stand should not be used for any other purpose than to support dryers that
meet these requirements.
21.4”
50.8”
total height
24.6”
total width
21.7”
total depth
4”
48.8”
21.5”
22.7”
maximum
washer width
maximum
washer height
Total installed
dimensions
Width 24.6”
Depth 25.7”
Height 50.8”