Black Nova BN ARIA User manual

BN Socket Collection
User Manual
All Rights Reserved - BLACK NOVA LTD. - 2020
Complete your design with The Socket Collection socket frames, that perfectly matches format and nishes of ARIA & ALBA
Collection keypads.
Frames are available in 1,2 and 3 modules versions.

Socket Frames - User Manual
Page 1/14
Index
Important Notes 2
Legal Principles 2
Subject to Change 2
Copyright 2
Personnel Qualification 2
Intended Use 2
Scope of Applicability 2
Safety information 3
Please note 3
Safety precautions 4
Introduction 5
Included in the box 6
Cleaning 6
Supported socket mechanisms 6
Mounting and installation 7
Socket frame front side 7
Socket frame back side 7
Glass Cut-Out Size 8
Support Frame Structure 9
Required back box types 9
Alternative back box types 10
Back box mounting 11
Back box mounting for single frame 11
Back box mounting for double frame 11
Back box mounting for triple frame 11
Installation 12
Installation with flush mount backbox 12
Installation with surface mount backbox 13
Warranty exclusion 14

Socket Frames - User Manual
Page 2/14
Important Notes
To ensure fast installation and start-up of the units, we strongly recommend that the following information
and explanations are carefully read and adhered to.
Legal Principles
Subject to Change
Black Nova reserves the right to make any alterations or modifications that serve to increase the efficiency
of technical progress. Black Nova owns all rights arising from the granting of patents or from the legal
protection of utility patents. Third-party products are always mentioned without any reference to patent
rights. Thus, the existence of such rights cannot be excluded.
Copyright
This documentation, including all figures and illustrations contained therein, is subject to copyright
protection. Any use of this documentation that infringes upon the copyright provisions stipulated herein is
prohibited. Reproduction, translation, electronic and phototechnical filing/archiving (e.g. photocopying),
as well as any amendments require the written consent of Black Nova. Non-observance will entail the right
of claims for damages.
Personnel Qualification
The use of the product described in this document is exclusively geared to specialists having qualifications
in Black Nova System programming, electrical specialists or persons instructed by electrical specialists who
are also familiar with the appropriate current standards. Black Nova assumes no liability resulting from
improper action and damage to Black Nova products and third-party products due to non- observance
of the information contained in this document.
Intended Use
For each individual application, the components are supplied from the factory with a dedicated hardware
and software configuration. Modifications are only admitted within the framework of the possibilities
documented in this document. All other changes to the hardware and/or software and the non-
conforming use of the components entail the exclusion of liability on part of Black Nova.
Please send your requests for modified and new hardware or software configurations directly to Black
Nova
Scope of Applicability
This application note is based on the stated hardware and software from the specific manufacturer, as
well as the associated documentation. This application note is therefore only valid for the described
installation. New hardware and software versions may need to be handled differently.
Please note the detailed description in the specific manuals.

Socket Frames - User Manual
Page 3/14
Safety information
Important Information
Read these instructions carefully before trying to install, configure, or operate products.
The following special messages may appear throughout this bulletin or on the equipment to warn of
potential hazards or to call attention to information that clarifies or simplifies a procedure.
This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey
all safety messages that follow this symbol to avoid possible injury or death.
The addition of either symbol to a “Danger” or “Warning” safety label indicates that an
electrical hazard exists which will result in personal injury if the instructions are not followed.
DANGER
DANGER indicates an imminently hazardous situation which, if not avoided, will result in death or
serious injury.
WARNING
WARNING indicates a potentially hazardous situation which, if not avoided, can result in death or
serious injury.
CAUTION
CAUTION indicates a potentially hazardous situation which, if not avoided, can result in minor or
moderate injury.
NOTICE
NOTICE is used to address practices not related to physical injury. The safety alert symbol shall not be
used with this signal word.
Please note
Electrical equipment should be installed, operated, serviced, and maintained only by qualified personnel.
No responsibility is assumed by Black Nova for any consequences arising out of the use of this material.
A qualified person is one who has skills and knowledge related to the construction, installation, and
operation of electrical equipment and has received safety training to recognize and avoid the hazards
involved.

Socket Frames - User Manual
Page 4/14
Safety precautions
WARNING
HAZARD OF INCORRECT INFORMATION
Do not incorrectly configure the product, as this can lead to incorrect reports and/or data results.
Do not base your maintenance or service actions solely on messages and information displayed by the
software.
Do not rely solely on software messages and reports to determine if the system is functioning correctly
or meeting all applicable standards and requirements.
Consider the implications of unanticipated transmission delays or failures of communications links.
Failure to follow these instructions can result in death, serious injury, or equipment damage.
The information provided in this documentation contains general descriptions and/or technical
characteristics of the performance of the products contained herein. This documentation is not intended
as a substitute for and is not to be used for determining suitability or reliability of these products for specific
user applications. It is the duty of any such user or integrator to perform the appropriate and complete risk
analysis, evaluation and testing of the products with respect to the relevant specific application or use
thereof.
Neither Black Nova nor any of its affiliates or subsidiaries shall be responsible or liable for misuse of the
information that is contained herein.
If you have any suggestions for improvements or amendments or have found errors in this publication,
please notify us.
All pertinent state, regional, and local safety regulations must be observed when installing and using this
product.
For reasons of safety and to help ensure compliance with documented system data, only the
manufacturer should perform repairs to components.
When devices are used for applications with technical safety requirements, the relevant instructions must
be followed.
Failure to use Black Nova product may result in injury, harm, or improper operating results.
Failure to observe this information can result in injury or equipment damage.
No part of this document may be reproduced in any form or by any means, electronic or mechanical,
including photocopying, without express written permission of Black Nova.

Socket Frames - User Manual
Page 5/14
Introduction
The Socket Frames
The refined and uniform design of the Socket Frames perfectly complements ARIA and ALBA panels. The
frames are available in 1, 2 and 3 sockets versions.
Black Nova supports Legrand Arteor 2 module Square Series functional sockets which are mounted in
support frame which PN is “5760 03”. Compatible Legrand surface mounting box also given. Related links
are as below.
Legrand Functional socket: https://www.legrand.com/ecatalogue/
Support Frame: https://www.legrand.com/ecatalogue/576003-support-frame-arteor-for-bs.html
Mounting Box: https://www.legrand.com/ecatalogue/572390-surface-mounting-box-arteor-brit-germ-
french.html

Socket Frames - User Manual
Page 6/14
Included in the box
1. The socket frame
2. Spacer
Please check the contents of the box immediately after unpacking the device.
Cleaning
Dirty socket frames may be cleaned with a dry cloth.
Supported socket mechanisms
Black Nova supports Legrand Arteor 2 module Square Series functional sockets which are mounted in
support frame which PN is “5760 03”. Please go to the link below for further details
https://www.legrand.com/ecatalogue/
Legrand Arteor, 2 module, Square Series functional socket example

Socket Frames - User Manual
Page 7/14
Mounting and installation
Socket frame front side
Single Frame
Double Frame
Triple Frame
Socket frame back side
1. Signage of the up side of the socket
2. Snaps to hold on the support frame

Socket Frames - User Manual
Page 8/14
Glass Cut-Out Size
Single Frame
Double Frame
Triple Frame

Socket Frames - User Manual
Page 9/14
Support Frame Structure
Legrand Arteor Support Frame (PN: 5760 03) is compatible with Black Nova socket frames. Please go to
the link below for further details
https://www.legrand.com/ecatalogue/576003-support-frame-arteor-for-bs.html
Legrand Arteor Support Frame (PN: 5760 03)
Required back box types
Legrand Surface mounting box (PN: 5723 90). Please go to the link below for further details
https://www.legrand.com/ecatalogue/572390-surface-mounting-box-arteor-brit-germ-french.html
Legrand Surface mounting box (PN: 5723 90)

Socket Frames - User Manual
Page 10/14
Alternative back box types
EU 2M and UK 3x3 standard back boxes might be used with socket frames. Please be aware of the depth
size of the back boxes. According to the socket mechanism to be use check depth size of the back boxes
whether depth size is enough
EU 2M Standard (mm) UK 3x3 Standard (mm)

Socket Frames - User Manual
Page 11/14
Back box mounting
Wall cut out dimensions may vary depending on the back box manufacturer. For exact cut out dimensions
please refer to the manufacturer of the back box.
Back box mounting for single frame
Back box mounting for double frame
Regardless of the BackBox type, the center distance between two BackBoxes is always 97.5 mm for the 2
socket frames
Back box mounting for triple frame
Regardless of the BackBox type, the center distance between two BackBoxes is always 97.5 mm for the 3
socket frames
W
Back
W
Back
Back
W
Back
Back
Back

Socket Frames - User Manual
Page 12/14
Installation
Installation with flush mount backbox
●Place spacer between flush mount backbox and support frame
●Screw the support frame to the back box
●Make sure that the cable is accessible from the back box

Socket Frames - User Manual
Page 13/14
Installation with surface mount backbox
●Screw the support frame to the back box
●Make sure that the cable is accessible from the back box

Socket Frames - User Manual
Page 14/14
Warranty exclusion
The Warranty does not apply in the following cases
●Damage caused by accident, flood, fire, earthquake, abuse, misuse, neglect, or other external
causes.
●Damage caused by improper use or inappropriate operating conditions including unstable
connection, poor grounding, external electromagnetic fields, exposure to direct sunlight, high
humidity, or vibration.
●Damage caused by service, including the installation of updates or extensions, or repairs performed
by anyone who is not authorized.
●Damage caused by connecting devices to the products of other manufacturers.
●Replacement of consumable parts, including cables, batteries, unless damage is caused by
defects in materials or workmanship.
●Cosmetic damage including, but not limited to, scratches, dents, or broken plastic.
●Periodic maintenance and inspection of the device including, but not limited to, cleaning,
adjusting, testing, or errors in programming.
●The warranty does not cover normal wear and tear caused by normal or excessive operation.