BLACK PANTHER BLACKPANTHERSYSTEM User manual

Keyboard Stand Basis-Set
for Amine, Babacu, Cedro, Para and S-Variants
BLACKPANTHERSYSTEM powered by MOTT Mobile Systeme Gmbh & Co KG – Am Dittwarer Bahnhof 9-11 - 97941 Tauberbischofsheim www.blackpanthersystem.de 01-010 Keyboardständer Basis_DE REV.05/05/2021
BLACKPANTHERSYSTEM Features
-expandable layers
-Mounting bracket for power strips
-Storage plates of various sizes
-Tabletops
-19“ Holder bracket
-Speaker holder
-Monitor holder
-Fan Articles
Model Variants Examples
Foreword
Dear Customer,
Thank you for choosing our BLACKPANTHERSYSTEM.
The BLACKPANTHERSYSTEM is a stable, modular and flexible
keyboard stand and studio stand system. All components are
perfectly matched to each other. BLACKPANTHER offers
numerous features, which can be supplemented to many
model variants. The system grows with your needs. With the
BLACKPANTHERSYSTEM you have acquired a high-quality
system, with a clear modern design, suitable for studio and
living rooms. A "must have" for life!
We ask you to observe the safety, assembly and care
instructions. This will ensure that you will have a lot of fun
with your BLACKPANTHERSYSTEM.
If you have any questions, requests or suggestions about the
system, please contact us using the contact form on our
website www.blackpanthersystem.de or directly by e-mail at
[e-mail].
With musical greetings
Team BLACKPANTHERSYSTEM

Keyboard Stand Basis-Set
for Amine, Babacu, Cedro, Para and S-Variants
BLACKPANTHERSYSTEM powered by MOTT Mobile Systeme Gmbh & Co KG – Am Dittwarer Bahnhof 9-11 - 97941 Tauberbischofsheim www.blackpanthersystem.de 01-010 Keyboardständer Basis_DE REV.05/05/2021
Specifications
Load capacity 80 kg
Dimensions Height 600 mm to 900 mm
Width 920 mm
Depth 620 mm
Support distance 540 mm
Height adjustable 8 steps from 600 mm to 900 mm
with locking screws
Net weight 10.8 kg
Material Tubes Steel, powder-coated
Screws Steel, galvanized
locking clamps Steel, PE
Plastic parts PA, PE, TPE
Package Box L=1000, B=850, H=80 mm
Important safety instructions
The keyboard stand must stand on a flat and load-bearing surface.
The keyboard stand must not be loaded beyond the permitted load
capacity.
The load within the approved load capacity must not be one-sided.
The load must be distributed as evenly as possible.
The feet must always be adjusted to the same height.
The tension screws must be fully engaged in the intended holes.
All screws must always be tightened.
The height adjustment must not be carried out in the loaded
state. Defective elements must be replaced for safety.
Assembly
5 6
Items 6
1Stands (2x) 7
2Locking screws (2x) 3
3Cover ring set (2x) 2 4 7
4Foot caps (4x)
5Carrier (1x) 1 3
6Bolt M8 (2x) 2
7Wing nut M8 (2x) 4
Assembly 1
Place stands parallel to each other.
The latching terminals should be aligned in the same direction.
Insert the carrier with the holes in the direction of the clamping
screws into the base frames and hold them at the desired height.
Snap the clamping screws into place. Align the stands parallel to
each other. Tighten the clamping screws.
The locking screws are used to fasten levels 1 to 3.
Note: The pads are not to be moved laterally and must be fastened
with 6 + 7. The other holes are for accessories only.
Cleaning
To clean the keyboard stand, use a damp cloth with a mild and non-
abrasive detergent.
Troubleshooting
The keyboard stand stands crooked -> set feet to the same height
and align parallel
The keyboard stand wobbles -> tighten clamps and screws