BLAM BT30 User manual

BLAM BT30
Wireless stereo speaker
USER MANUAL
Box Content
• 30W Wireless Speaker
• Audio Cable (jack 3.5mm - jack 3.5mm)
• Charging cable
• User Manual
1. Power button
Press and hold for three seconds to turn on/off.
Auto power off after 40 minutes idea for power saving.
2. Previous button
Press to navigate between tracks.
3. Play/Pause button
Use to play and pause audio. While in Bluetooth mode, press and hold
to activate Siri or S-Voice. Press again to disable. Incoming call: press
once to answer, press again to end. Press and hold to decline call.
4. Next button
Press to navigate between tracks.
5. Mode button
Use this button to toggle between Bluetooth/AUX/USB mode. Press
and hold to pair TWS speakers together.
6. Bluetooth button
If there is no AUX cable inserted, the speaker will automatically enter
default Bluetooth Mode. When in Bluetooth mode, press to initiate
Bluetooth pairing.
7. Charging Indicator
Flashing red: battery is low.
Solid green: device is charging.
8. Battery-Level Indicator
Lights indicate remaining power.
Flashing: device is charging. Solid: device is fully charged.
9. Volume decrease button
10. Thermal sensor
Detects the heat of a human hand and will automatically activate the
devices frosted LED button-backlighting.
11. Microphone
Remain within three feet of microphone while speaking.
12. AUX indicator
When an AUX cable is inserted into speaker, the device will
automatically enter AUX mode. When solid green indicator light is on,
AUX mode is enabled.
13. Volume increase button
14. Bluetooth indicator
When the indicator light is on, Bluetooth mode is enabled. When
Bluetooth is in pairing mode, a blue indicator will flash. Once a device
has been paired, blue indicator will remain solid.
15. NFC area
Hold your device over this area to use NFC for Bluetooth Connection.
16. AUX IN port
Connects speaker to external media devices.
17. AUX OUT port
For headphone use.
18. Micro USB Jack
This port cannot be used for external device connection, for charging
use only.
19. USB power port
Provides power to connected devices. This function is enabled when
speaker is on.
20. Reset button
Press to reset device.
TRUE WIRELESS STEREO SOUND (TWS)
Connect two speakers in stereo
Une fois Once on of your two speakers are successfully paired
with a device, follow these steps to pair TWS:
• Press Mode button 5on the first speaker to enter pairing with
blue indication flashing and pairing prompts.
• Power the 2nd speaker to paring (disconnected if Bluetooth
connected).
• A tone will sound when the two speakers have been successfully
paired with purple Bluetooth indicator on the 1st speaker and
yellow indicator on 2nd speaker.
• Now you can enjoy the crisp stereo surround sound with separate
left channel and right channel. The next time when both speakers
are powered on, the need to be re-paired.
NOTE
- TWS function available only in Bluetooth & AUX IN mode.
- No memory function for TWS connection.
Two speakers shut down simultaneously while power off.
Follow the above instruction to pair the two speakers again next
time when you turn on.
Bluetooth
1. Power on speaker and hold your phone or other device within 3 feet
of the speaker, press the Bluetooth button 6: the speaker will
enter pairing mode and the indicator light should begin flashing.
2. Pairing mode will automatically be stopped (signaled by a beep)
after 3 minutes. To re-enter pairing mode, follow the instructions
beginning at step 1.
3. Ensure Bluetooth is enabled on the device you want to pair the
speaker with.
4. The speaker will appear as “BT30” when scanning for available
devices.
5. When selecting “BT30” from the list, if prompted for a password,
enter ‘’0000’’.
6. The speaker will record this device as the last device paired.
7. When in Bluetooth mode you can with to AUX mode by inserting
the AUX cable.
8. Incoming calls will override music and other media with an incoming
call voice prompt, simply press the Play button 3. to answer/end
or press and hold to decline the call. Press the Play button 3to
answer a second incoming call.
9. Press and hold the Play button 3for three seconds to activate
Siri/S-Voice function of your phone.
AUX
Insert the AUX cord into the designated port to automatically switch
the speaker to AUX mode. While in AUX mode, AUX indicator will
glow Connect your audio device to AUX input with the supplied
3.5mm audio cable.
NFC
Turn on the NFC function on the device you wish to connect to your
speaker. Touch the device to the speaker NFC area located on the
top of the speaker next to the Mic. Port. The speaker will connect
automatically.
CAUTION
Proper use
1. To prevent damage and risk of electrical shock, do not expose this
device to dust, vibration, rain, water or liquids of any kind.
2. Do not place device near open flames or extreme heat sources.
Always place your device on level, flat and stable surfaces.
3. Avoid placing items on top of the speaker.
4. Do not use excessive force when pressing buttons or handling
speaker.
5. To clean your speakers, use a dry, soft cloth or minimally damp cloth
without any corrosive solvent or cleaning agent.
SAFETY
To prevent fire, shock or injury, please do not disassemble or replace
any parts of this speaker. If your device becomes damaged or in need
of repair, please contact a professional maintenance or qualified
service center for assistance. We are not responsible for any personal
injury or property damage caused by improper use of this product.
Please do not allow the use of this speaker by small children without
proper adult supervision.

BLAM BT30
Wireless stereo speaker
USER MANUAL
Box Content
• 30W Wireless Speaker
• Audio Cable (jack 3.5mm - jack 3.5mm)
• Charging cable
• User Manual
1. Power button
Press and hold for three seconds to turn on/off.
Auto power off after 40 minutes idea for power saving.
2. Previous button
Press to navigate between tracks.
3. Play/Pause button
Use to play and pause audio. While in Bluetooth mode, press and hold
to activate Siri or S-Voice. Press again to disable. Incoming call: press
once to answer, press again to end. Press and hold to decline call.
4. Next button
Press to navigate between tracks.
5. Mode button
Use this button to toggle between Bluetooth/AUX/USB mode. Press
and hold to pair TWS speakers together.
6. Bluetooth button
If there is no AUX cable inserted, the speaker will automatically enter
default Bluetooth Mode. When in Bluetooth mode, press to initiate
Bluetooth pairing.
7. Charging Indicator
Flashing red: battery is low.
Solid green: device is charging.
8. Battery-Level Indicator
Lights indicate remaining power.
Flashing: device is charging. Solid: device is fully charged.
9. Volume decrease button
10. Thermal sensor
Detects the heat of a human hand and will automatically activate the
devices frosted LED button-backlighting.
11. Microphone
Remain within three feet of microphone while speaking.
12. AUX indicator
When an AUX cable is inserted into speaker, the device will
automatically enter AUX mode. When solid green indicator light is on,
AUX mode is enabled.
13. Volume increase button
14. Bluetooth indicator
When the indicator light is on, Bluetooth mode is enabled. When
Bluetooth is in pairing mode, a blue indicator will flash. Once a device
has been paired, blue indicator will remain solid.
15. NFC area
Hold your device over this area to use NFC for Bluetooth Connection.
16. AUX IN port
Connects speaker to external media devices.
17. AUX OUT port
For headphone use.
18. Micro USB Jack
This port cannot be used for external device connection, for charging
use only.
19. USB power port
Provides power to connected devices. This function is enabled when
speaker is on.
20. Reset button
Press to reset device.
TRUE WIRELESS STEREO SOUND (TWS)
Connect two speakers in stereo
Une fois Once on of your two speakers are successfully paired
with a device, follow these steps to pair TWS:
• Press Mode button 5on the first speaker to enter pairing with
blue indication flashing and pairing prompts.
• Power the 2nd speaker to paring (disconnected if Bluetooth
connected).
• A tone will sound when the two speakers have been successfully
paired with purple Bluetooth indicator on the 1st speaker and
yellow indicator on 2nd speaker.
• Now you can enjoy the crisp stereo surround sound with separate
left channel and right channel. The next time when both speakers
are powered on, the need to be re-paired.
NOTE
- TWS function available only in Bluetooth & AUX IN mode.
- No memory function for TWS connection.
Two speakers shut down simultaneously while power off.
Follow the above instruction to pair the two speakers again next
time when you turn on.
Bluetooth
1. Power on speaker and hold your phone or other device within 3 feet
of the speaker, press the Bluetooth button 6: the speaker will
enter pairing mode and the indicator light should begin flashing.
2. Pairing mode will automatically be stopped (signaled by a beep)
after 3 minutes. To re-enter pairing mode, follow the instructions
beginning at step 1.
3. Ensure Bluetooth is enabled on the device you want to pair the
speaker with.
4. The speaker will appear as “BT30” when scanning for available
devices.
5. When selecting “BT30” from the list, if prompted for a password,
enter ‘’0000’’.
6. The speaker will record this device as the last device paired.
7. When in Bluetooth mode you can with to AUX mode by inserting
the AUX cable.
8. Incoming calls will override music and other media with an incoming
call voice prompt, simply press the Play button 3. to answer/end
or press and hold to decline the call. Press the Play button 3to
answer a second incoming call.
9. Press and hold the Play button 3for three seconds to activate
Siri/S-Voice function of your phone.
AUX
Insert the AUX cord into the designated port to automatically switch
the speaker to AUX mode. While in AUX mode, AUX indicator will
glow Connect your audio device to AUX input with the supplied
3.5mm audio cable.
NFC
Turn on the NFC function on the device you wish to connect to your
speaker. Touch the device to the speaker NFC area located on the
top of the speaker next to the Mic. Port. The speaker will connect
automatically.
CAUTION
Proper use
1. To prevent damage and risk of electrical shock, do not expose this
device to dust, vibration, rain, water or liquids of any kind.
2. Do not place device near open flames or extreme heat sources.
Always place your device on level, flat and stable surfaces.
3. Avoid placing items on top of the speaker.
4. Do not use excessive force when pressing buttons or handling
speaker.
5. To clean your speakers, use a dry, soft cloth or minimally damp cloth
without any corrosive solvent or cleaning agent.
SAFETY
To prevent fire, shock or injury, please do not disassemble or replace
any parts of this speaker. If your device becomes damaged or in need
of repair, please contact a professional maintenance or qualified
service center for assistance. We are not responsible for any personal
injury or property damage caused by improper use of this product.
Please do not allow the use of this speaker by small children without
proper adult supervision.

BLAM BT30
Wireless stereo speaker
USER MANUAL
Box Content
• 30W Wireless Speaker
• Audio Cable (jack 3.5mm - jack 3.5mm)
• Charging cable
• User Manual
1. Power button
Press and hold for three seconds to turn on/off.
Auto power off after 40 minutes idea for power saving.
2. Previous button
Press to navigate between tracks.
3. Play/Pause button
Use to play and pause audio. While in Bluetooth mode, press and hold
to activate Siri or S-Voice. Press again to disable. Incoming call: press
once to answer, press again to end. Press and hold to decline call.
4. Next button
Press to navigate between tracks.
5. Mode button
Use this button to toggle between Bluetooth/AUX/USB mode. Press
and hold to pair TWS speakers together.
6. Bluetooth button
If there is no AUX cable inserted, the speaker will automatically enter
default Bluetooth Mode. When in Bluetooth mode, press to initiate
Bluetooth pairing.
7. Charging Indicator
Flashing red: battery is low.
Solid green: device is charging.
8. Battery-Level Indicator
Lights indicate remaining power.
Flashing: device is charging. Solid: device is fully charged.
9. Volume decrease button
10. Thermal sensor
Detects the heat of a human hand and will automatically activate the
devices frosted LED button-backlighting.
11. Microphone
Remain within three feet of microphone while speaking.
12. AUX indicator
When an AUX cable is inserted into speaker, the device will
automatically enter AUX mode. When solid green indicator light is on,
AUX mode is enabled.
13. Volume increase button
14. Bluetooth indicator
When the indicator light is on, Bluetooth mode is enabled. When
Bluetooth is in pairing mode, a blue indicator will flash. Once a device
has been paired, blue indicator will remain solid.
15. NFC area
Hold your device over this area to use NFC for Bluetooth Connection.
16. AUX IN port
Connects speaker to external media devices.
17. AUX OUT port
For headphone use.
18. Micro USB Jack
This port cannot be used for external device connection, for charging
use only.
19. USB power port
Provides power to connected devices. This function is enabled when
speaker is on.
20. Reset button
Press to reset device.
TRUE WIRELESS STEREO SOUND (TWS)
Connect two speakers in stereo
Une fois Once on of your two speakers are successfully paired
with a device, follow these steps to pair TWS:
• Press Mode button 5on the first speaker to enter pairing with
blue indication flashing and pairing prompts.
• Power the 2nd speaker to paring (disconnected if Bluetooth
connected).
• A tone will sound when the two speakers have been successfully
paired with purple Bluetooth indicator on the 1st speaker and
yellow indicator on 2nd speaker.
• Now you can enjoy the crisp stereo surround sound with separate
left channel and right channel. The next time when both speakers
are powered on, the need to be re-paired.
NOTE
- TWS function available only in Bluetooth & AUX IN mode.
- No memory function for TWS connection.
Two speakers shut down simultaneously while power off.
Follow the above instruction to pair the two speakers again next
time when you turn on.
Bluetooth
1. Power on speaker and hold your phone or other device within 3 feet
of the speaker, press the Bluetooth button 6: the speaker will
enter pairing mode and the indicator light should begin flashing.
2. Pairing mode will automatically be stopped (signaled by a beep)
after 3 minutes. To re-enter pairing mode, follow the instructions
beginning at step 1.
3. Ensure Bluetooth is enabled on the device you want to pair the
speaker with.
4. The speaker will appear as “BT30” when scanning for available
devices.
5. When selecting “BT30” from the list, if prompted for a password,
enter ‘’0000’’.
6. The speaker will record this device as the last device paired.
7. When in Bluetooth mode you can with to AUX mode by inserting
the AUX cable.
8. Incoming calls will override music and other media with an incoming
call voice prompt, simply press the Play button 3. to answer/end
or press and hold to decline the call. Press the Play button 3to
answer a second incoming call.
9. Press and hold the Play button 3for three seconds to activate
Siri/S-Voice function of your phone.
AUX
Insert the AUX cord into the designated port to automatically switch
the speaker to AUX mode. While in AUX mode, AUX indicator will
glow Connect your audio device to AUX input with the supplied
3.5mm audio cable.
NFC
Turn on the NFC function on the device you wish to connect to your
speaker. Touch the device to the speaker NFC area located on the
top of the speaker next to the Mic. Port. The speaker will connect
automatically.
CAUTION
Proper use
1. To prevent damage and risk of electrical shock, do not expose this
device to dust, vibration, rain, water or liquids of any kind.
2. Do not place device near open flames or extreme heat sources.
Always place your device on level, flat and stable surfaces.
3. Avoid placing items on top of the speaker.
4. Do not use excessive force when pressing buttons or handling
speaker.
5. To clean your speakers, use a dry, soft cloth or minimally damp cloth
without any corrosive solvent or cleaning agent.
SAFETY
To prevent fire, shock or injury, please do not disassemble or replace
any parts of this speaker. If your device becomes damaged or in need
of repair, please contact a professional maintenance or qualified
service center for assistance. We are not responsible for any personal
injury or property damage caused by improper use of this product.
Please do not allow the use of this speaker by small children without
proper adult supervision.

BLAM BT30
Wireless stereo speaker
USER MANUAL
Box Content
• 30W Wireless Speaker
• Audio Cable (jack 3.5mm - jack 3.5mm)
• Charging cable
• User Manual
1. Power button
Press and hold for three seconds to turn on/off.
Auto power off after 40 minutes idea for power saving.
2. Previous button
Press to navigate between tracks.
3. Play/Pause button
Use to play and pause audio. While in Bluetooth mode, press and hold
to activate Siri or S-Voice. Press again to disable. Incoming call: press
once to answer, press again to end. Press and hold to decline call.
4. Next button
Press to navigate between tracks.
5. Mode button
Use this button to toggle between Bluetooth/AUX/USB mode. Press
and hold to pair TWS speakers together.
6. Bluetooth button
If there is no AUX cable inserted, the speaker will automatically enter
default Bluetooth Mode. When in Bluetooth mode, press to initiate
Bluetooth pairing.
7. Charging Indicator
Flashing red: battery is low.
Solid green: device is charging.
8. Battery-Level Indicator
Lights indicate remaining power.
Flashing: device is charging. Solid: device is fully charged.
9. Volume decrease button
10. Thermal sensor
Detects the heat of a human hand and will automatically activate the
devices frosted LED button-backlighting.
11. Microphone
Remain within three feet of microphone while speaking.
12. AUX indicator
When an AUX cable is inserted into speaker, the device will
automatically enter AUX mode. When solid green indicator light is on,
AUX mode is enabled.
13. Volume increase button
14. Bluetooth indicator
When the indicator light is on, Bluetooth mode is enabled. When
Bluetooth is in pairing mode, a blue indicator will flash. Once a device
has been paired, blue indicator will remain solid.
15. NFC area
Hold your device over this area to use NFC for Bluetooth Connection.
16. AUX IN port
Connects speaker to external media devices.
17. AUX OUT port
For headphone use.
18. Micro USB Jack
This port cannot be used for external device connection, for charging
use only.
19. USB power port
Provides power to connected devices. This function is enabled when
speaker is on.
20. Reset button
Press to reset device.
TRUE WIRELESS STEREO SOUND (TWS)
Connect two speakers in stereo
Une fois Once on of your two speakers are successfully paired
with a device, follow these steps to pair TWS:
• Press Mode button 5on the first speaker to enter pairing with
blue indication flashing and pairing prompts.
• Power the 2nd speaker to paring (disconnected if Bluetooth
connected).
• A tone will sound when the two speakers have been successfully
paired with purple Bluetooth indicator on the 1st speaker and
yellow indicator on 2nd speaker.
• Now you can enjoy the crisp stereo surround sound with separate
left channel and right channel. The next time when both speakers
are powered on, the need to be re-paired.
NOTE
- TWS function available only in Bluetooth & AUX IN mode.
- No memory function for TWS connection.
Two speakers shut down simultaneously while power off.
Follow the above instruction to pair the two speakers again next
time when you turn on.
Bluetooth
1. Power on speaker and hold your phone or other device within 3 feet
of the speaker, press the Bluetooth button 6: the speaker will
enter pairing mode and the indicator light should begin flashing.
2. Pairing mode will automatically be stopped (signaled by a beep)
after 3 minutes. To re-enter pairing mode, follow the instructions
beginning at step 1.
3. Ensure Bluetooth is enabled on the device you want to pair the
speaker with.
4. The speaker will appear as “BT30” when scanning for available
devices.
5. When selecting “BT30” from the list, if prompted for a password,
enter ‘’0000’’.
6. The speaker will record this device as the last device paired.
7. When in Bluetooth mode you can with to AUX mode by inserting
the AUX cable.
8. Incoming calls will override music and other media with an incoming
call voice prompt, simply press the Play button 3. to answer/end
or press and hold to decline the call. Press the Play button 3to
answer a second incoming call.
9. Press and hold the Play button 3for three seconds to activate
Siri/S-Voice function of your phone.
AUX
Insert the AUX cord into the designated port to automatically switch
the speaker to AUX mode. While in AUX mode, AUX indicator will
glow Connect your audio device to AUX input with the supplied
3.5mm audio cable.
NFC
Turn on the NFC function on the device you wish to connect to your
speaker. Touch the device to the speaker NFC area located on the
top of the speaker next to the Mic. Port. The speaker will connect
automatically.
CAUTION
Proper use
1. To prevent damage and risk of electrical shock, do not expose this
device to dust, vibration, rain, water or liquids of any kind.
2. Do not place device near open flames or extreme heat sources.
Always place your device on level, flat and stable surfaces.
3. Avoid placing items on top of the speaker.
4. Do not use excessive force when pressing buttons or handling
speaker.
5. To clean your speakers, use a dry, soft cloth or minimally damp cloth
without any corrosive solvent or cleaning agent.
SAFETY
To prevent fire, shock or injury, please do not disassemble or replace
any parts of this speaker. If your device becomes damaged or in need
of repair, please contact a professional maintenance or qualified
service center for assistance. We are not responsible for any personal
injury or property damage caused by improper use of this product.
Please do not allow the use of this speaker by small children without
proper adult supervision.

BLAM BT30
Wireless stereo speaker
USER MANUAL
Box Content
• 30W Wireless Speaker
• Audio Cable (jack 3.5mm - jack 3.5mm)
• Charging cable
• User Manual
1. Power button
Press and hold for three seconds to turn on/off.
Auto power off after 40 minutes idea for power saving.
2. Previous button
Press to navigate between tracks.
3. Play/Pause button
Use to play and pause audio. While in Bluetooth mode, press and hold
to activate Siri or S-Voice. Press again to disable. Incoming call: press
once to answer, press again to end. Press and hold to decline call.
4. Next button
Press to navigate between tracks.
5. Mode button
Use this button to toggle between Bluetooth/AUX/USB mode. Press
and hold to pair TWS speakers together.
6. Bluetooth button
If there is no AUX cable inserted, the speaker will automatically enter
default Bluetooth Mode. When in Bluetooth mode, press to initiate
Bluetooth pairing.
7. Charging Indicator
Flashing red: battery is low.
Solid green: device is charging.
8. Battery-Level Indicator
Lights indicate remaining power.
Flashing: device is charging. Solid: device is fully charged.
9. Volume decrease button
10. Thermal sensor
Detects the heat of a human hand and will automatically activate the
devices frosted LED button-backlighting.
11. Microphone
Remain within three feet of microphone while speaking.
12. AUX indicator
When an AUX cable is inserted into speaker, the device will
automatically enter AUX mode. When solid green indicator light is on,
AUX mode is enabled.
13. Volume increase button
14. Bluetooth indicator
When the indicator light is on, Bluetooth mode is enabled. When
Bluetooth is in pairing mode, a blue indicator will flash. Once a device
has been paired, blue indicator will remain solid.
15. NFC area
Hold your device over this area to use NFC for Bluetooth Connection.
16. AUX IN port
Connects speaker to external media devices.
17. AUX OUT port
For headphone use.
18. Micro USB Jack
This port cannot be used for external device connection, for charging
use only.
19. USB power port
Provides power to connected devices. This function is enabled when
speaker is on.
20. Reset button
Press to reset device.
TRUE WIRELESS STEREO SOUND (TWS)
Connect two speakers in stereo
Une fois Once on of your two speakers are successfully paired
with a device, follow these steps to pair TWS:
• Press Mode button 5on the first speaker to enter pairing with
blue indication flashing and pairing prompts.
• Power the 2nd speaker to paring (disconnected if Bluetooth
connected).
• A tone will sound when the two speakers have been successfully
paired with purple Bluetooth indicator on the 1st speaker and
yellow indicator on 2nd speaker.
• Now you can enjoy the crisp stereo surround sound with separate
left channel and right channel. The next time when both speakers
are powered on, the need to be re-paired.
NOTE
- TWS function available only in Bluetooth & AUX IN mode.
- No memory function for TWS connection.
Two speakers shut down simultaneously while power off.
Follow the above instruction to pair the two speakers again next
time when you turn on.
Bluetooth
1. Power on speaker and hold your phone or other device within 3 feet
of the speaker, press the Bluetooth button 6: the speaker will
enter pairing mode and the indicator light should begin flashing.
2. Pairing mode will automatically be stopped (signaled by a beep)
after 3 minutes. To re-enter pairing mode, follow the instructions
beginning at step 1.
3. Ensure Bluetooth is enabled on the device you want to pair the
speaker with.
4. The speaker will appear as “BT30” when scanning for available
devices.
5. When selecting “BT30” from the list, if prompted for a password,
enter ‘’0000’’.
6. The speaker will record this device as the last device paired.
7. When in Bluetooth mode you can with to AUX mode by inserting
the AUX cable.
8. Incoming calls will override music and other media with an incoming
call voice prompt, simply press the Play button 3. to answer/end
or press and hold to decline the call. Press the Play button 3to
answer a second incoming call.
9. Press and hold the Play button 3for three seconds to activate
Siri/S-Voice function of your phone.
AUX
Insert the AUX cord into the designated port to automatically switch
the speaker to AUX mode. While in AUX mode, AUX indicator will
glow Connect your audio device to AUX input with the supplied
3.5mm audio cable.
NFC
Turn on the NFC function on the device you wish to connect to your
speaker. Touch the device to the speaker NFC area located on the
top of the speaker next to the Mic. Port. The speaker will connect
automatically.
CAUTION
Proper use
1. To prevent damage and risk of electrical shock, do not expose this
device to dust, vibration, rain, water or liquids of any kind.
2. Do not place device near open flames or extreme heat sources.
Always place your device on level, flat and stable surfaces.
3. Avoid placing items on top of the speaker.
4. Do not use excessive force when pressing buttons or handling
speaker.
5. To clean your speakers, use a dry, soft cloth or minimally damp cloth
without any corrosive solvent or cleaning agent.
SAFETY
To prevent fire, shock or injury, please do not disassemble or replace
any parts of this speaker. If your device becomes damaged or in need
of repair, please contact a professional maintenance or qualified
service center for assistance. We are not responsible for any personal
injury or property damage caused by improper use of this product.
Please do not allow the use of this speaker by small children without
proper adult supervision.

BLAM BT30
Wireless stereo speaker
USER MANUAL
Box Content
• 30W Wireless Speaker
• Audio Cable (jack 3.5mm - jack 3.5mm)
• Charging cable
• User Manual
1. Power button
Press and hold for three seconds to turn on/off.
Auto power off after 40 minutes idea for power saving.
2. Previous button
Press to navigate between tracks.
3. Play/Pause button
Use to play and pause audio. While in Bluetooth mode, press and hold
to activate Siri or S-Voice. Press again to disable. Incoming call: press
once to answer, press again to end. Press and hold to decline call.
4. Next button
Press to navigate between tracks.
5. Mode button
Use this button to toggle between Bluetooth/AUX/USB mode. Press
and hold to pair TWS speakers together.
6. Bluetooth button
If there is no AUX cable inserted, the speaker will automatically enter
default Bluetooth Mode. When in Bluetooth mode, press to initiate
Bluetooth pairing.
7. Charging Indicator
Flashing red: battery is low.
Solid green: device is charging.
8. Battery-Level Indicator
Lights indicate remaining power.
Flashing: device is charging. Solid: device is fully charged.
9. Volume decrease button
10. Thermal sensor
Detects the heat of a human hand and will automatically activate the
devices frosted LED button-backlighting.
11. Microphone
Remain within three feet of microphone while speaking.
12. AUX indicator
When an AUX cable is inserted into speaker, the device will
automatically enter AUX mode. When solid green indicator light is on,
AUX mode is enabled.
13. Volume increase button
14. Bluetooth indicator
When the indicator light is on, Bluetooth mode is enabled. When
Bluetooth is in pairing mode, a blue indicator will flash. Once a device
has been paired, blue indicator will remain solid.
15. NFC area
Hold your device over this area to use NFC for Bluetooth Connection.
16. AUX IN port
Connects speaker to external media devices.
17. AUX OUT port
For headphone use.
18. Micro USB Jack
This port cannot be used for external device connection, for charging
use only.
19. USB power port
Provides power to connected devices. This function is enabled when
speaker is on.
20. Reset button
Press to reset device.
TRUE WIRELESS STEREO SOUND (TWS)
Connect two speakers in stereo
Une fois Once on of your two speakers are successfully paired
with a device, follow these steps to pair TWS:
• Press Mode button 5on the first speaker to enter pairing with
blue indication flashing and pairing prompts.
• Power the 2nd speaker to paring (disconnected if Bluetooth
connected).
• A tone will sound when the two speakers have been successfully
paired with purple Bluetooth indicator on the 1st speaker and
yellow indicator on 2nd speaker.
• Now you can enjoy the crisp stereo surround sound with separate
left channel and right channel. The next time when both speakers
are powered on, the need to be re-paired.
NOTE
- TWS function available only in Bluetooth & AUX IN mode.
- No memory function for TWS connection.
Two speakers shut down simultaneously while power off.
Follow the above instruction to pair the two speakers again next
time when you turn on.
Bluetooth
1. Power on speaker and hold your phone or other device within 3 feet
of the speaker, press the Bluetooth button 6: the speaker will
enter pairing mode and the indicator light should begin flashing.
2. Pairing mode will automatically be stopped (signaled by a beep)
after 3 minutes. To re-enter pairing mode, follow the instructions
beginning at step 1.
3. Ensure Bluetooth is enabled on the device you want to pair the
speaker with.
4. The speaker will appear as “BT30” when scanning for available
devices.
5. When selecting “BT30” from the list, if prompted for a password,
enter ‘’0000’’.
6. The speaker will record this device as the last device paired.
7. When in Bluetooth mode you can with to AUX mode by inserting
the AUX cable.
8. Incoming calls will override music and other media with an incoming
call voice prompt, simply press the Play button 3. to answer/end
or press and hold to decline the call. Press the Play button 3to
answer a second incoming call.
9. Press and hold the Play button 3for three seconds to activate
Siri/S-Voice function of your phone.
AUX
Insert the AUX cord into the designated port to automatically switch
the speaker to AUX mode. While in AUX mode, AUX indicator will
glow Connect your audio device to AUX input with the supplied
3.5mm audio cable.
NFC
Turn on the NFC function on the device you wish to connect to your
speaker. Touch the device to the speaker NFC area located on the
top of the speaker next to the Mic. Port. The speaker will connect
automatically.
CAUTION
Proper use
1. To prevent damage and risk of electrical shock, do not expose this
device to dust, vibration, rain, water or liquids of any kind.
2. Do not place device near open flames or extreme heat sources.
Always place your device on level, flat and stable surfaces.
3. Avoid placing items on top of the speaker.
4. Do not use excessive force when pressing buttons or handling
speaker.
5. To clean your speakers, use a dry, soft cloth or minimally damp cloth
without any corrosive solvent or cleaning agent.
SAFETY
To prevent fire, shock or injury, please do not disassemble or replace
any parts of this speaker. If your device becomes damaged or in need
of repair, please contact a professional maintenance or qualified
service center for assistance. We are not responsible for any personal
injury or property damage caused by improper use of this product.
Please do not allow the use of this speaker by small children without
proper adult supervision.