BLK BOX GOLIATH PT POD User manual

OWNERS MANUAL & QUICK START GUIDE
PT POD GOLIATH
NOTE : PLEASE READ ALL THE INSTRUCTIONS
CAREFULLY BEFORE ASSEMBLING THIS PRODUCT.
BLK BOX
PRODUCT SPECIFICATION
21-0600
#MADEINBELFAST
170kg
PRODUCT WEIGHT
MAX USER WEIGHT
MAX USER
MAX TRAINING WEIGHT
DIMENSIONS
SAFE WORKING ZONE
-125kg
300kg
1200mm x 2408mm x 980mm
-
-
-
-2700mm x 3272mm x 3580mm
1
-

WARNING
SPIRIT LEVEL
10MM MASONRY
DRILL BIT
TOOLS REQUIRED
30MM SPANNER X 2
17MM SPANNER X2
13MM SPANNER
HAMMER
HAMMER DRILL VACUUM STEP LADDER
PARTS & ATTACHMENTS
No. Name SKU QTY
12.4 UPRIGHT DNA60 WITH FEET 21-0036-0A 4
21.2 BRANDING BOX CM DNA60 21-0017-0A 1
31.2 BOX CM DNA60 21-0013-0A 2
40.7 BOX CM DNA60 21-0036-0A 4
5UTILITY PEG 21-0234-0B 6
6MULTIGRIPS DNA60 21-0151-0A 1
7M10X80 SLEEVE ANCHOR 16-0031 12
8M10X90 BOLT 10-0008 46
9M10 FLAT WASHER 10-0019 104
10 M10 NYLOCK NUT 10-0024 46
11 J-HOOK PAIR 16-0001 1
12 M20X100 BOLT 10-0134 12
13 M20 FLAT WASHER 10-0023 24
14 M20 NYLOCK NUT 10-0028 12
1
2
3
4
11
7
8
10 9
SERIOUS OR FATAL INJURIES MAY OCCUR FROM INCORRECTLY ASSEMBLED EQUIPMENT. ALWAYS ENSURE
BOLTS ARE TIGHTENED CORRECTLY AND ALL PARTS ARE LEVEL AND PLUMB. TO FURTHER REDUCE RISK OF
INJURIES OR DEATH PLEASE USE OUR SUGGESTED TOOLS AND PERSONAL PROTECTIVE EQUIPMENT (PPE).
WE SUGGEST THAT A MINIMUM OF THREE PEOPLE ARE INVOLVED IN THE ASSEMBLY OF THIS PRODUCT.
EACH PERSON SHOULD BE EQUIPPED WITH SAFETY GLASSES, STEEL TOE CAP BOOTS AND EAR PLUGS.
PLEASE BE AWARE OF THIS SYMBOL AS AN INDICATION TO CHECK THAT A PART IS LEVEL
OR PLUMB.
THIS SYMBOL IS AN INDICATION OF THE RECOMMENDED TORQUE EACH
BOLT SHOULD BE TIGHTENED TO. THIS VALUE WILL BE DEPENDENT ON
THE BOLT TYPE. PLEASE HAND TIGHTEN ALL BOLTS UNTIL YOU SEE THIS SYMBOL.
#MADEINBELFAST
6
5
xx
Nm
13
14
12

ASSEMBLY
x
8
x
4
1
BOLT 1QTY BRANDING BOX(21-0017-0A] AND 1QTY1.2BOX (21-0013-0A)BETWEEN2QTY
UPRIGHTS (21-0036-0A) WITH BOLTS ASSEMBLY AS SHOWN. ENSURE LOGOS ON
BRANDING BOX (21-0017-0A) IS FACING FORWARD, LOGOS ON UPRIGHTS ARE
FACING OUTWARD AND ALL BOLTS FACING INWARDS.
10.0008
10.0019 x2
10.0024
10.0008
10.0019 x2
10.0024
#MADEINBELFAST

2
BOLT 6QTY UTILITY PEG (21-0234) AND 6QTY SIDE PLATES (PLATES VARY DEPENDING ON SHELF)
EITHER SIDE OF 2QTY UPRIGHT (21-0036-0A) WITH BOLT ASSEMBLY AS SHOWN.
10.0134
10.0023 x2
10.0028
10.0134
10.0023 x2
10.0028
#MADEINBELFAST

3
BOLT 3QTY SHELVES (SHELVES VARY DEPENDING ON ORDER) TO 6QTY SIDE PLATES WITH BOLT
ASSEMBLY AS SHOWN.
10.0001
10.0019 x2
10.0024
10.0001
10.0019 x2
10.0024
#MADEINBELFAST

4BOLT 1QTY 1.2 BOX (21-0013-0A) BETWEEN 2QTY UPRIGHTS (21-0036-0A) AND CONNECT TO
EXISTING ASSEMBLY USING 4QTY 0.7 BOX (21-0011-0A) WITH BOLT ASSEMBLY AS SHOWN. BOLT
1QTY MULTIGRIPS (21-0151-0A) TO 1QTY 1.2 BOX (21-0013-0A) WITH BOLT ASSEMBLY AS SHOWN
ENSURE LOGO ON UPRIGHTS ARE FACING OUTWARD AND BOLTS ARE FACING INWARD.
10.0008
10.0019 x2
10.0024
10.0008
10.0019 x2
10.0024
10.0008
10.0019 x2
10.0024
10.0008
10.0019 x2
10.0024
#MADEINBELFAST
10.0008
10.0019 x2
10.0024

5
TIGHTEN ALL BOLT ASSEMBLIES TO 30NM TORQUE. ENSURE ALL
UPRIGHTS ARE PLUMB. DRILL AND SECURE THE MIDDLE HOLE ON EACH UPRIGHT AS
SHOWN IN GUIDE. REMOVE ALL BOTTOM CROSSMEMBERS, DRILL AND SECURE
REMAINING HOLES ON UPRIGHTS AS SHOWN IN GUIDE. REATTACH THE BOTTOM
CROSSMEMBERS. ATTACH J-HOOKS AND LANDMINE AS BELOW.
#MADEINBELFAST
10.0031
10.0019
10.0031
10.0019
30
Nm
DRILL
HOLE
90MM
VACUUM
HAMMERIN
BOLT
TIGHTEN
SLEEVE ANCHOR
BOLT FITTING
-DRILL 10MM HOLE
THROUGH FLOOR
COVERING, 90MM
DEEP USING PLATE
AS A GUIDE.
-VACUUM OUT THE
DUST.
-HAMMER SLEEVE
ANCHOR DOWN
INTO THE HOLE.
-TIGHTEN SLEEVE
ANCHOR TO
SPECIFIED TORQUE
USING 13MM
SPANNER.

1:1 SCALE FASTENERS
FOR TERMS AND CONDITIONS VISIT OUR WEBSITE AT
www.blkboxtness.com/pages/terms-conditions
GET IN TOUCH
TEL: [phone]
EMAIL:info@blkboxtness.com
DISCOVER MORE AT:
www.blkboxtness.com
M10x80 SLEEVE ANCHOR
10-0031
M10x90 BOLT
10-0008
NYLOCK NUT
10-0024
M10 FLAT WASHER
10-0019
#MADEINBELFAST

#MADEINBELFAST
THIS IS A BLANK PAGE