BLK BOX BLACKOUT 21-0711 User manual

OWNERS MANUAL & QUICK START GUIDE
BLACKOUT HALF RACK - 2.2M
NOTE : PLEASE READ ALL THE INSTRUCTIONS
CAREFULLY BEFORE ASSEMBLING THIS PRODUCT.
BLK BOX
21-0711
#MADEINBELFAST
1200mmx1100mmx2266mm
2312mmx2820mmx3076mm
88kg
PRODUCT SPECIFICATION
PRODUCT WEIGHT
MAX USER WEIGHT
MAX USER
MAX TRAINING WEIGHT
DIMENSIONS
SAFE WORKING ZONE
-
350kg
125kg
-
-
-
-
1
-

WARNING
30
Nm
SPIRIT LEVEL
10MM MASONRY
DRILL BIT
TOOLS REQUIRED
17MM SPANNER X2
13MM SPANNER
HAMMER
HAMMER DRILL VACUUM STEP LADDER
PARTS & ATTACHMENTS
No. Name SKU QTY
1 BLACKOUT SQUAT STAND UPRIGHT 2.2M 21-0573 4
2 BLACKOUT SQUAT STAND BASE FRAME 21-0572 2
3 BLACKOUT SQUAT STAND BACK CM 21-0602 1
4 GOLIATH 1.2 SINGLE BAR 21-0015 2
5 BLACKOUT HALF RACK CM 20-0543 2
6 BLACKOUT SQUAT STAND FOOT PLATE 20-0412 2
7 BLACKOUT BRACE PLATE 20-0472 6
8 J-HOOK (PAIR) 16-0001 1
9 M10X90 HEX HEAD BOLT 10-0008 36
10 M10 WAHER 10-0019 74
11 M10 NYLOCK NUT 10-0024 36
12 M10 SLEEVE ANCHOR BOLT 10-0031 2
1
2
3
9
10 11
8
SERIOUS OR FATAL INJURIES MAY OCCUR FROM INCORRECTLY ASSEMBLED EQUIPMENT. ALWAYS
ENSURE BOLTS ARE TIGHTENED CORRECTLY AND ALL PARTS ARE LEVEL AND PLUMB. TO FURTHER
REDUCE RISK OF INJURIES OR DEATH PLEASE USE OUR SUGGESTED TOOLS AND PERSONAL PRO-
TECTIVE EQUIPMENT (PPE). WE SUGGEST THAT A MINIMUM OF THREE PEOPLE ARE INVOLVED IN
THE ASSEMBLY OF THIS PRODUCT. EACH PERSON SHOULD BE EQUIPPED WITH SAFETY GLASSES,
STEEL TOE CAP BOOTS AND EAR PLUGS.
PLEASE BE AWARE OF THIS SYMBOL AS AN INDICATION TO CHECK THAT A PART IS
LEVEL OR PLUMB.
THIS SYMBOL IS AN INDICATION OF THE RECOMMENDED TORQUE EACH
BOLT SHOULD BE TIGHTENED TO. THIS VALUE WILL BE DEPENDENT ON
THE BOLT TYPE. PLEASE HAND TIGHTEN ALL BOLTS UNTIL YOU SEE THIS SYMBOL.
#MADEINBELFAST
4
6
7
12
5

ASSEMBLY
1
BOLT 1QTY BACK CM (21-0602), 2QTY BASE FRAME (21-0572) AND 6QTY BRACE
PLATE (20-0472) WITH BOLTS ASSEMBLY AS SHOWN.
BOLT ASSEMBLY
FOR EACH HOLE:
10.0008
10.0019 x2
10.0024
#MADEINBELFAST
2INSERT 1QTY UPRIGHT (21-0573) INTO TAB SLOTS ON BASE FRAME (21-0572) AND
ATTACH USING BOLT ASSEMBLIES AS SHOWN BELOW. REPEAT FOR EACH SET OF
TAB SLOTS.
BOLT ASSEMBLIES:
10.0008
10.0019 x2
10.0024

3
PLACE 1QTY HALF RACK(20-0543) BETWEEN 2 UPRIGHTS AND ATTACH WITH BOLT
ASSEMBLIES AS SHOWN. REPEAT ON OPPOSITE SIDE.
#MADEINBELFAST
4
BOLT 1QTY SINGLE BAR(20-0543) TO UPRIGHTS AND ATTACH WITH BOLT ASSEMBLIES AS
SHOWN. REPEAT ON OPPOSITE SIDE.
BOLT ASSEMBLY
FOR EACH HOLE:
10.0008
10.0019 x2
10.0024
BOLT ASSEMBLY
FOR EACH HOLE:
10.0008
10.0019 x2
10.0024

5
ATTACH 1 QTY FOOT PLATE (20-0412) USING BOLT ASSEMBLIES AS SHOWN.
REPEAT ON OPPOSITE SIDE.
FOLLOW 4 STEP GUIDE BELOW FOR FLOOR MOUNTING.
#MADEINBELFAST
BOLT ASSEMBLY
FOR EACH HOLE:
10.0008
10.0019 x2
10.0024
1. USING HAMMER DRILL, DRILL A 10MM WIDE HOLE, 90MM
DEEP USING FOOT PLATE AS A GUIDE.
2. VACUUM OUT THE DUST.
FLOOR MOUNTING
TIGHTEN
3. HAMMER SLEEVE ANCHOR BOLT INTO THE HOLE.
4. TIGHTEN SLEEVE ANCHOR BOLT TO SPECIFIED
TORQUE USING 13MM SPANNER.
30
Nm
VACUUMDRILL HOLE
90MM HAMMER IN BOLT
6
TIGHTEN ALL BOLT ASSEMBLIES TO 30NM.
ENSURE UPRIGHTS ARE PLUMB AND ALL SINGLE BARS ARE LEVEL.
30
Nm

#MADEINBELFAST
1:1 SCALE FASTENERS
FOR TERMS AND CONDITIONS VISIT OUR WEBSITE AT:
www.blkboxtness.com/pages/terms-conditions
GET IN TOUCH:
TEL: [phone]
EMAIL: info@blkboxtness.com
DISCOVER MORE AT:
www.blkboxtness.com
M10x80 SLEEVE ANCHOR
10-0031
M10x90 BOLT
10-0008
NYLOCK NUT
10-0024
M10 FLAT WASHER
10-0019