Blomberg SND 9683 A++ User manual

SND 9683 A++ - SND 9683 XA++ - SND9683 XN - SND 9683 N
Cooler/Freezer
User Manual
Køl/Frys
Brugervejledning
Kyl/Frys
Bruksanvisning
Kjøl/Frys
Bruksanvisning
Käyttöopas
Jääkaappi/Pakastin
57 3807 0000/AJ
EN / DA / SV / NO / FIN

EN
2
Please read this user manual first!
Dear Customer,
We hope that your product, which has been produced in modern plants and
checked under the most meticulous quality control procedures, will provide you
an effective service.
Therefore, read this entire user manual carefully before using the product and
keep it as a reference. If you handover the product to someone else, give the user
manual as well.
The user manual will help you use the product in a fast and safe way.
 Read the manual before installing and operating the product.
 Make sure you read the safety instructions.
 Keep the manual in an easily accessible place as you may need it later.
 Read the other documents given with the product.
Remember that this user manual is also applicable for several other models.
Differences between models will be identified in the manual.
Explanation of symbols
Throughout this user manual the following symbols are used:
CImportant information or useful tips.
AWarning against dangerous conditions for life and property.
BWarning against electric voltage.
A
A
A
C
SUPPLIER’S NAME MODEL IDENTIFIER (*)
INFORMATION
C
The model information as stored in the product data base
can be reached by entering following website and searching
for your model identifier (*) found on energy label.
https://eprel.ec.europa.eu/

EN
3
CONTENTS
1 Your cooler/freezer 4
2 Safety and environment
instructions 5
3 Installation 9
Points to be paid attention to when the
relocation of the cooler/freezer...........9
Before you start the cooler/freezer, ....9
Electrical connection..........................9
Disposing of the packaging .............10
Disposing of your old cooler/freezer.10
Placing and Installation ....................10
Changing the illumination lamp .......11
Adjusting the legs ............................11
4 Preparation 12
5 Using your cooler/freezer 13
Indicator Panel.................................13
Using interior compartments............15
Cooling............................................15
Placing the food ..............................15
6 Maintenance and cleaning 16
Protection of plastic surfaces ..........16
7 Troubleshooting 17

EN
4
1Your cooler/freezer
1. Control Panel
2. Interior light
3. Movable shelves
4. Wine rack
5. Crisper cover
6. Crisper
C Figures that take place in this instruction manual are schematic and may not
correspond exactly with your product. If the subject parts are not included in the
product you have purchased, then it is valid for other models.
7. Adjustable front feet
8. Butter & Cheese sections
9. Adjustable door shelves
10. Egg compartment
11. Bottle shelter wire
12. 0 °C Compartment
* OPTIONAL
9
1
3
6
7
8
4
5
10
2
11
12

EN
5
2Safety and environment instructions
This section provides the safety
instructions necessary to prevent the
risk of injury and material damage.
Failure to observe these instructions will
invalidate all types of product warranty.
Intended use
A
WARNING:
Keep ventilation openings,
in the appliance enclosure
or in the built-instructure,
clear of obstruction.
A
WARNING:
Do not use mechanical
devices or other means
to accelerate the defrosting
process, other than those
recommended by the
manufacturer.
A
WARNING:
Do not damage the
refrigerant circuit.
A
WARNING:
Do not use electrical
appliances inside the food
storage compartments
of the appliance, unless
they are of the type
recommended by the
manufacturer.
This appliance is intended to be used
in household and similar applications
such as
– staff kitchen areas in shops, offices
and other working environments;
– farm houses and by clients in hotels,
motels and other residential type
environments;
–bedandbreakfasttypeenvironments;
– catering and similar non-retail
applications.
1.1. General safety
 This product should not be
used by persons with physi-
cal, sensory and mental di-
sabilities, without sufficient
knowledge and experience or
by children. The device can
only be used by such persons
under supervision and ins-
truction of a person respon-
sible for their safety. Children
should not be allowed to play
with this device.
 In case of malfunction, unplug
the device.
 After unplugging, wait at least
5 minutes before plugging in
again.
 Unplug the product when not
in use.
 Do not touch the plug with
wet hands! Do not pull the
cable to plug off, always hold
the plug.
 Do not plug in the refrigerator
if the socket is loose.
 Unplug the product during
installation, maintenance, cle-
aning and repair.
 If the product will not be used
for a while, unplug the pro-
duct and remove any food
inside.
 Do not use the product when
the compartment with circuit
cards located on the upper
back part of the product
(electrical card box cover) (1)
is open.

EN
6
1
1
 Do not use steam or stea-
med cleaning materials for
cleaning the refrigerator and
melting the ice inside. Steam
may contact the electrified
areas and cause short circuit
or electric shock!
 Do not wash the product by
spraying or pouring water on
it! Danger of electric shock!
 In case of malfunction, do not
use the product, as it may
cause electric shock. Contact
the authorised service before
doing anything.
 Plug the product into an eart-
hed socket. Earthing must be
done by a qualified electrici-
an.
 If the product has LED type
lighting, contact the authori-
sed service for replacing or in
case of any problem.
 Do not touch frozen food with
wet hands! It may adhere to
your hands!
 Do not place liquids in bott-
les and cans into the freezer
compartment. They may exp-
lode.
 Place liquids in upright positi-
on after tightly closing the lid.
 Do not spray flammable
substances near the product,
as it may burn or explode.
 Do not keep flammable mate-
rials and products with flam-
mable gas (sprays, etc.) in the
refrigerator.
 Do not place containers
holding liquids on top of the
product. Splashing water on
an electrified part may cause
electric shock and risk of fire.
 Exposing the product to
rain, snow, sunlight and wind
will cause electrical danger.
When relocating the product,
do not pull by holding the
door handle. The handle may
come off.
 Take care to avoid trapping
any part of your hands or
body in any of the moving
parts inside the product.
 Do not step or lean on the
door, drawers and similar
parts of the refrigerator. This
will cause the product to fall
down and cause damage to
the parts.
 Take care not to trap the po-
wer cable.

EN
7
1.1.1 HC warning
If the product comprises a
cooling system using R600a
gas, take care to avoid
damaging the cooling system
and its pipe while using and
moving the product. This gas is
flammable. If the cooling system
is damaged, keep the product
away from sources of fire and
ventilate the room immediately.
C
The label on the inner
left side indicates the
type of gas used in the
product.
1.1.2 For models with
water dispenser
 Pressure for cold water inlet
shall be maximum 90 psi (6.2
bar). If your water pressure
exceeds 80 psi (5.5 bar), use
a pressure limiting valve in
your mains system. If you do
not know how to check your
water pressure, ask for the
help of a professional plum-
ber.
 If there is risk of water ham-
mer effect in your installation,
always use a water ham-
mer prevention equipment
in your installation. Consult
Professional plumbers if you
are not sure that there is no
water hammer effect in your
installation.
 Do not install on the hot wa-
ter inlet. Take precautions
against of the risk of freezing
of the hoses. Water tempe-
rature operating interval shall
be 33°F (0.6°C) minimum and
100°F (38°C) maximum.
 Use drinking water only.
1.2. Intended use
 This product is designed for
home use. It is not intended
for commercial use.
 The product should be used
to store food and beverages
only.
 Do not keep sensitive pro-
ducts requiring controlled
temperatures (vaccines, heat
sensitive medication, medical
supplies, etc.) in the refrige-
rator.
 The manufacturer assumes
no responsibility for any da-
mage due to misuse or mis-
handling.
 Original spare parts will be
provided for 10 years, follo-
wing the product purchasing
date.
1.3. Child safety
 Keep packaging materials out
of children’s reach.
 Do not allow the children to
play with the product.
 If the product’s door compri-
ses a lock, keep the key out
of children’s reach.

EN
8
1.4. Compliance with WEEE
Directive and Disposing
of the Waste Product
This product complies with
EU WEEE Directive (2012/19/EU). This
product bears a classification symbol
for waste electrical and electronic
equipment (WEEE).
This product has been
manufactured with high
quality parts and materials
which can be reused and
are suitable for recycling.
Do not dispose of the
waste product with normal
domestic and other wastes at the end
of its service life. Take it to the collection
center for the recycling of electrical and
electronic equipment. Please consult
your local authorities to learn about
these collection centers.
1.5. Compliance with
RoHS Directive
 This product complies with EU
WEEE Directive (2011/65/EU). It
does not contain harmful and pro-
hibited materials specified in the
Directive.
1.6. Package information
 Packaging materials of the product
are manufactured from recyclable
materials in accordance with our
National Environment Regulations.
Do not dispose of the packaging
materials together with the domestic
or other wastes. Take them to the
packaging material collection points
designated by the local authorities.

EN
9
3Installation
BThe manufacturer will not be liable
for any event caused by disregarding
the information supplied in this user
manual.
Points to be paid attention
to when the relocation of the
cooler/freezer
1. Your cooler/freezer should be
unplugged.Before transportation
of your cooler/freezer, it should be
emptied and cleaned.
2. Before it is re-packaged, shelves,
accessories, crisper, etc. inside
your cooler/freezer should be fixed
with adhesive tape and secured
against impacts. Package should
be bound with a thick tape and the
transportation rules on the package
should be strictly observed.
3. Original packaging and foam
materials should be kept for future
transportations or moving.
Before you start the cooler/
freezer,
Check the following before you start
to use your cooler/freezer:
1. Attach 2plastic wedges as illustrated
below. Plastic wedges are intended
to keep the distance which will
ensure the air circulation between
your cooler/freezer and the wall.
(The picture is drawn up as a
representation and it is not identical
with your product.)
2. Clean the interior of the cooler/
freezer as recommended in the
“Maintenance and cleaning” section.
3. Connect the plug of the cooler/
freezer to the wall socket. When the
fridge door is opened, fridge internal
lamp will turn on.
4. When the compressor starts to
operate, a sound will be heard. The
liquid and gases sealed within the
refrigeration system may also give rise
to noise, even if the compressor is
not running and this is quite normal.
5. Front edges of the cooler/freezer
may feel warm. This is normal. These
areas are designed to be warm to
avoid condensation.
Electrical connection
Connect your product to a grounded
socket which is being protected by a
fuse with the appropriate capacity.
Important:
The connection must be in compliance
with national regulations.
 The power plug must be easily
accessible after installation.

EN
10
 Electrical safety of your cooler/freezer
shall be guaranteed only if the earth
system in your house complies with
standards.
 The voltage stated on the label
located at left inner side of your
product should be equal to your
network voltage.
 Extension cables and multi plugs
must not be used for connection.
BA damaged power cable must be
replaced by a qualified electrician.
BFaulty product must not be operated
before it is repaired! There is the risk
of electric shock!
Disposing of the packaging
The packing materials may be
dangerous for children. Keep the
packing materials out of the reach
of children or dispose of them by
classifying them in accordance with the
waste instructions stated by your local
authorities. Do not throw away with
regular house waste, throw away on
packaging pick up spots designated by
the local authorities.
The packing of your cooler/freezer is
produced from recyclable materials.
Disposing of your old cooler/
freezer
Dispose of your old cooler/freezer
without giving any harm to the
environment.
 You may consult your authorized
dealer or waste collection center of
your municipality about the disposal
of your cooler/freezer.
Before disposing of your cooler/
freezer, cut out the electric plug and, if
there are any locks on the door, make
them inoperable in order to protect
children against any danger.
Placing and Installation
AIf the entrance door of the room
where the cooler/freezer will be installed
is not wide enough for the cooler/
freezer to pass through, then carefully
remove the doors of your cooler/freezer
and pass it sideways through the door.
1. Install your cooler/freezer to a place
that allows ease of use.
2. Keep your cooler/freezer away from
heat sources, humid places and
direct sunlight.
3. There must be appropriate air
ventilation around your cooler/
freezer in order to achieve an efficient
operation. If the cooler/freezer is to be
placed in a recess in the wall, there
must be at least 5 cm distance with
the ceiling and at least 5 cm with the
wall. Do not place your product on
the materials such as rug or carpet.
4. Place your cooler/freezer on an even
floor surface to prevent jolts.
WARNING:
Do not locate extension
sockets or charging transformers/
power supplies or Lithium-Iron battery
operated products adjacent to the
compressor as they could overheat.

EN
11
Changing the illumination
lamp
To change the Bulb/LED used for
illumination of your refrigerator, call your
AuthorisedService.
The lamp(s) used in this appliance
is not suitable for household room
illumination. The intended purpose of
this lamp is to assist the user to place
foodstuffs in the refrigerator/freezer in
a safe and comfortable way.The lamps
used in this appliance have to withstand
extreme physical conditions such as
temperatures below -20 °C.
(only chest and upright freezer)
Adjusting the legs
If your refrigerator is unbalanced;
You can balance your refrigerator by
turning its front legs as illustrated in the
figure. The corner where the leg exists is
lowered when you turn in the direction
of black arrow and raised when you
turn in the opposite direction. Taking
help from someone to slightly lift the
refrigerator will facilitate this process.

EN
12
4Preparation
 For a freestanding appliance; ‘this
refrigerating appliance is not intended
to be used as a built-in appliance.
 Your cooler/freezer should be
installed at least 30 cm away from
heat sources such as hobs, ovens,
central heater and stoves and at least
5 cm away from electrical ovens and
should not be located under direct
sunlight.
 The ambient temperature of the room
where you install your cooler/freezer
should at least be 10°C. Operating
your cooler/freezer under cooler
conditions is not recommended with
regard to its efficiency.
 Please make sure that the interior
of your cooler/freezer is cleaned
thoroughly.
 If two cooler/freezers are to be
installed side by side, there should be
at least 2 cm distance between them.
 When you operate your cooler/freezer
for the first time, please observe the
following instructions during the initial
six hours.
 The door should not be opened
frequently.
 It must be operated empty without
any food in it.
 Do not unplug your cooler/freezer.
If a power failure occurs out of your
control, please see the warnings in
the “Recommended solutions for the
problems” section.
 Original packaging and foam
materials should be kept for future
transportations or moving.
 Due to temperature change as a
result of opening/closing the product
door during operation, condensation
on the door/body shelves and the
glass containers is normal.
 Since hot and humid air will not
directly penetrate into your product
when the doors are not opened,
your product will optimize itself in
conditions sufficient to protect your
food. Functions and components
such as compressor, fan, heater,
defrost, lighting, display and so on
will operate according to the needs
to consume minimum energy under
these circumstances.

EN
13
5Using your cooler/freezer
2
4
3
8
7
5
11
12
1
9
10
6
Indicator Panel
1. Quick Fridge Function:
Quick Fridge indicator turns on when
the Quick Fridge function is on. Press
Quick Fridge button again to cancel
this function. Quick Fridge indicator
will turn off and normal settings will be
resumed. Quick Fridge function will
be cancelled automatically 34 hours
later if you do not cancel it manually.
If you want to cool plenty amount of
fresh food, press Quick Fridge button
before you place the food into the
fridge compartment. If you press
the Quick Fridge button repeatedly
with short intervals, the electronic
circuit protection will be activated
and the compressor will not start up
immediately.

EN
14
2. Quick Fridge Indicator
This icon flashes in an animated style
when the Quick Fridge function is
active.
3. Fridge Set Function:
This function allows you to make
the Fridge compartment temperature
setting. Press this button to set the
temperature of the fridge compartment
to 10,9,8,7,6,5,4,3,2 and 1 respectively.
4. Fridge Compartment
Temperature Setting Indicator
Indicates the temperature set for the
Fridge Compartment.
5. Vacation Function
When you press Vacation button,
vacation function is activated and
vacation indicator lits.If this function is
activated, Fridge compartment cooling
is stopped and fridge compartment
temperature is kept at 15 C° in order
to prevent bad smelling. Press Vacation
button again to deactivate vacation
function.
6. Vacation Indicator:
This icon lights up when the Vacation
Function is active.
7. High Temperature/Error Warning
Indicator:
This light comes on during high
temperature failures and error warnings.
8. Economic Usage Indicator:
Economic Usage Indicator turns on
when the Fridge Compartment is set to
8-9-10°C.
9-Energy Saving Function
When you press this button, Energy
saving icon will light up and Energy
Saving Function will be activated. If
energy saving function is active, all
icons on the display other than energy
saving icon will turn off. When the
Energy Saving Function is active, if
any button is pressed or the door is
opened, Energy Saving Function will
be exited and the icons on display will
return to normal.If you press this buton
again, Energy Saving icon will turn off
and Energy Saving Function will not be
active.
10-Energy Saving Indicator
This icon lights up when the Energy
Saving Function is selected
11-Key Lock Mode
Press Key Lock button concurrently
for 3 seconds. Key lock icon will
light up and key lock mode will be
activated. Buttons will not function if
the Key Lock mode is active.
Press Key Lock button concurrently
for 3 seconds again. Key lock icon will
turn off and the key lock mode will be
exited.
12-Key Lock Indicator
This icon lights up when the Key Lock
mode is activated.

EN
15
Using interior compartments
Body shelves:
Distance between the shelves can be
adjusted when necessary.
Crisper:
Vegetables and fruits can be stored
in this compartment for long periods
without decaying.
Bottle shelf:
Bottles, jars and tins can be placed in
these shelves.
Cooling
Food storage
The fridge compartment is for the
short-term storage of fresh food and
drinks.
Store milk products in the intended
compartment in the refrigerator.
Bottles can be stored in the bottle
holder or in the bottle shelf of the door.
Raw meat is best kept in a polyethylene
bag in the compartment at the very
bottom of the refrigerator.
Allow hot foods and beverages to cool
to room temperature prior to placing
them in the refrigerator.
 Attention
Store concentrated alcohol only
standing upright and tightly closed.
 Attention
Do not store explosive substances or
containers with flammable propellant
gases (canned cream, spray cans
etc.) in the device. There is a danger of
explosion.
Placing the food
Egg tray Egg
Fridge
compartment
shelves
Food in pans,
covered plates
and closed
containers
Fridge
compartment
door shelves
Small and
packaged food
or drinks (such as
milk, fruit juice and
beer)
Crisper Vegetables and
fruits
Defrosting of the appliance
The appliance defrosts automatically.

EN
16
6Maintenance and cleaning
ANever use gasoline, benzene or
similar substances for cleaning
purposes.
BWe recommend that you unplug the
appliance before cleaning.
BNever use any sharp abrasive
instrument, soap, household
cleaner, detergent and wax polish for
cleaning.
CUse lukewarm water to clean the
cabinet of your cooler/freezer and
wipe it dry.
CUse a damp cloth wrung out in
a solution of one teaspoon of
bicarbonate of soda to one pint of
water to clean the interior and wipe it
dry.
BMake sure that no water enters the
lamp housing and other electrical
items.
BIf your cooler/freezer is not going to
be used for a long period of time,
unplug the power cable, remove all
food, clean it and leave the door ajar.
CCheck door seals regularly to ensure
they are clean and free from food
particles.
ATo remove door racks, remove all the
contents and then simply push the
door rack upwards from the base.
ANever use cleaning agents or water
that contain chlorine to clean the
outer surfaces and chromium coated
parts of the product. Chlorine causes
corrosion on such metal surfaces.
A Do not use sharp, abrasive tools,
soap, household cleaning agents,
detergents, kerosene, fuel oil,
varnish etc. to prevent removal and
deformation of the prints on the
plastic part. Use lukewarm water
and a soft cloth for cleaning and then
wipe it dry.
Protection of plastic
surfaces
CDo not put the liquid oils or oil-
cooked meals in your cooler/freezer
in unsealed containers as they
damage the plastic surfaces of your
cooler/freezer. In case of spilling or
smearing oil on the plastic surfaces,
clean and rinse the relevant part of
the surface at once with warm water.

EN
17
7Troubleshooting
Please review this list before calling the service. It will save your time and
money. This list includes frequent complaints that are not arising from defective
workmanship or material usage. Some of the features described here may not
exist in your product.
The cooler/freezer does not operate.
 The plug is not inserted into the socket correctly. >>>Insert the plug into the
socket securely.
 The fuse of the socket which your cooler/freezer is connected to or the main
fuse have blown out. >>>Check the fuse.
Condensation on the side wall of the fridge compartment (MULTIZONE, COOL
CONTROL and FLEXI ZONE).
 Door has been opened frequently. >>>Do not open and close the door of
cooler/freezer frequently.
 Ambient is very humid. >>>Do not install your cooler/freezer into highly humid
places.
 Food containing liquid is stored in open containers. >>>Do not store food with
liquid content in open containers.
 Door of the cooler/freezer is left ajar. >>>Close the door of the cooler/freezer.
 Thermostat is set to a very cold level. >>>Set the thermostat to a suitable level.
 Compressor is not running
 Protective thermic of the compressor will blow out during sudden power failures
or plug-out plug-ins as the refrigerant pressure in the cooling system of the
cooler/freezer has not been balanced yet. The cooler/freezer will start running
approximately after 6 minutes. Please call the service if the cooler/freezer does
not startup at the end of this period.
 The fridge is in defrost cycle. >>>This is normal for a full-automatically defrosting
cooler/freezer. Defrosting cycle occurs periodically.
 The cooler/freezer is not plugged into the socket. >>>Make sure that the plug is
fit into the socket.
 Temperature settings are not made correctly. >>>Select the suitable temperature
value.
 There is a power outage. >>>Cooler/freezer returns to normal operation when
the power restores.
The operation noise increases when the cooler/freezer is running.
 The operating performance of the cooler/freezer may change due to the
changes in the ambient temperature. It is normal and not a fault.
The cooler/freezer is running frequently or for a long time.

EN
18
 New product may be wider than the previous one. Larger cooler/freezers
operate for a longer period of time.
 The room temperature may be high. >>>It is normal that the product operates
for longer periods in hot ambient.
 The cooler/freezer might be plugged in recently or might be loaded with food.
>>>When the cooler/freezer is plugged in or loaded with food recently, it will take
longer for it to attain the set temperature. This is normal.
 Large amounts of hot food might be put in the cooler/freezer recently. >>>Do
not put hot food into the cooler/freezer.
 Doors might be opened frequently or left ajar for a long time. >>>The warm
air that has entered into the cooler/freezer causes the cooler/freezer to run for
longer periods. Do not open the doors frequently.
 Freezer or fridge compartment door might be left ajar. >>>Check if the doors are
closed completely.
 The cooler/freezer is adjusted to a very low temperature. >>>Adjust the cooler/
freezer temperature to a warmer degree and wait until the temperature is
achieved.
 Door seal of the fridge or freezer may be soiled, worn out, broken or not properly
seated. >>>Clean or replace the seal. Damaged/broken seal causes the
cooler/freezer to run for a longer period of time in order to maintain the current
temperature.
Freezer temperature is very low while the fridge temperature is sufficient.
 The freezer temperature is adjusted to a very low value. >>>Adjust the freezer
temperature to a warmer degree and check.
Fridge temperature is very low while the freezer temperature is sufficient.
 The fridge temperature is adjusted to a very low value. >>>Adjust the fridge
temperature to a warmer degree and check.
Food kept in the fridge compartment drawers is frozen.
 The fridge temperature is adjusted to a very high value. >>>Adjust the fridge
temperature to a lower value and check.
Temperature in the fridge or freezer is very high.

EN
19
 The fridge temperature is adjusted to a very high value. >>>Fridge compartment
temperature setting has an effect on the temperature of the freezer. Change the
temperatures of the fridge or freezer and wait until the relevant compartments
attain a sufficient temperature.
 Doors are opened frequently or left ajar for a long time. >>>Do not open the
doors frequently.
 Door is ajar. >>>Close the door completely.
 The cooler/freezer is plugged in or loaded with food recently. >>>This is normal.
When the cooler/freezer is plugged in or loaded with food recently, it will take
longer for it to attain the set temperature.
 Large amounts of hot food might be put in the cooler/freezer recently. >>>Do
not put hot food into the cooler/freezer.
 Vibrations or noise.
 The floor is not level or stable. >>> If the cooler/freezer rocks when moved
slowly, balance it by adjusting its feet. Also make sure that the floor is strong
enough to carry the cooler/freezer, and level.
 The items put onto the cooler/freezer may cause noise. >>>Remove the items
on top of the cooler/freezer.
There are noises coming from the cooler/freezer like liquid flowing, spraying,
etc.
 Liquid and gas flows occur in accordance with the operating principles of your
cooler/freezer. It is normal and not a fault.
Whistle comes from the cooler/freezer.
 Fans are used in order to cool the cooler/freezer. It is normal and not a fault.
Condensation on the inner walls of cooler/freezer.
 Hot and humid weather increases icing and condensation. It is normal and not a
fault.
 Doors are opened frequently or left ajar for a long time. >>>Do not open the
doors frequently. Close them if they are open.
 Door is ajar. >>>Close the door completely.
Humidity occurs on the outside of the cooler/freezer or between the doors.
 There might be humidity in the air; this is quite normal in humid weather. When
the humidity is less, condensation will disappear.
Bad odour inside the cooler/freezer.

EN
20
 No regular cleaning is performed. >>>Clean the inside of the cooler/freezer
regularly with a sponge, lukewarm water or carbonate dissolved in water.
 Some containers or package materials may cause the smell. >>>Use a different
container or different brand packaging material.
 Food is put into the cooler/freezer in uncovered containers. >>>Keep the food
in closed containers. Microorganisms spreading out from uncovered containers
can cause unpleasant odours.
 Remove the foods that have expired best before dates and spoiled from the
cooler/freezer.
The door is not closing.
 Food packages are preventing the door from closing. >>>Replace the packages
that are obstructing the door.
 The cooler/freezer is not completely even on the floor. >>>Adjust the feet to
balance the cooler/freezer.
 The floor is not level or strong. >>>Make sure that the floor is level and capable
to carry the cooler/freezer.
Crispers are stuck.
 The food is touching the ceiling of the drawer. >>>Rearrange food in the drawer.