Blu TEE005 Instruction Manual

2017-06
1 866 907 0122 blubathworks.com
TEE005
Installation & User Manual
NETLEVEL - Module
Point to point and Server connection
TEE005

2017-06
1 866 907 0122 blubathworks.com
1
Attention – Before Installation
1. Inspect this product to ensure you have all parts as shown that are required for proper installation.
2. This product must be installed by a professional contractor.
3. Refer to the specication and assembly drawings attached for installation directions.
Installation Requirements
Please read the instructions carefully so as to avoid any damage to the xture.
1. To ensure this product is installed properly, you must read and follow these guidelines.
2. Be sure your installation conforms to local codes.
3. Refer to the specication and assembly drawings attached.
4. Use only a strap wrench or protected/smooth-jaw wrench on any nished surface.
5. Do NOT use putty during this installation.
Cleaners For Fittings And Accessories
To avoid damaging the surface and working components of the ttings, certain precautions must be taken
in terms of usage and subsequent cleaning as many cleaning agents contain acids for general cleaning and
removing calcium deposits. When caring for your ttings and accessories, please note the following:
- Only apply cleaners which are expressly intended for the use
- Never use any cleaner containing hydrochloric acid, formic acid or acetic acid on or near the tting, as
they can cause considerable damage
- Do not use cleaners containing phosphoric acid
- Do not use cleaners containing chlorine bleach solutions
- Never mix or combine cleaning agents
- Abrasive cleaners and unsuitable scouring agents such as scouring pads
Technical Support Assistance
If further assistance is required, please contact:
Product Support at 1.866.907.0122 (09:00 – 17:00hrs PST) or email [email protected]
North America
Blu Bathworks Inc.
188 Smithe Street,Vancouver, BC, Canada, V6B 6A9
T +1.604.299.0122 F +1.604.299.0125
Please refer to blubathworks.com for warranty, terms & conditions under warranty & procedure for warranty service.

2017-06
1 866 907 0122 blubathworks.com
2
Structure
ON: 222016
SN: 1309160001
CONTROL MIXER
- TEE030
- TEE030S
- TEE030SV
PCB
- TEE030
- TEE030S
- TEE030SV
WLAN
Wi-Fi Module
TEE005
iPhone/iPad Router
MAX 33 ft
[10m]
MAX 66 ft
[20m]
MAX 33 ft
[10m]
Repeater
Supported Security:
WPA & WPA2 Open
Not Supported Security:
WPA/WPA2 Enterprise
MAX 33 ft [10m]: If distance
is exceeding 33ft [10m],
set up a Repeater between
devices

2017-06
1 866 907 0122 blubathworks.com
3
Compatible Control Mixers
TEE030S
- 2 outlet
- Shower/Handshower
TEE030
- 2 outlet
- Tub ller/Handshower
TEE030SV
- 3 outlet
- Shower/Handshower/Body Jets

2017-06
1 866 907 0122 blubathworks.com
4
Note location, password and serial number
Location
Password (PW):
Serial Number (SN):
Location
Password (PW):
Serial Number (SN):
Location
Password (PW):
Serial Number (SN):
Location
Password (PW):
Serial Number (SN):

2017-06
1 866 907 0122 blubathworks.com
5
Netlevel Introduction and important notes
Compatibility and using this guide:
The IoT module is compatible with most ‘smart devices’ with a web browser app. This
installation guide uses an iPad and a Galaxy Tab to demonstrate the installation and setup
procedures.
This guide uses a bath processor as an example. The shower processors are setup via the
same steps, but are missing some of the bath-related functions.
Server connection:
The module can allow your device to be controlled outside of the home via a dedicated server.
The server connection will only function correctly if there is sucient mobile coverage. Please
note that your mobile network may apply a charge for the use of 3G or 4G connections.
Bath processors:
The IoT module allows the user to remotely ll a bath, either by manually setting the
temperature and volume, or by selecting the pre-sets which the user can save via the main
interface (consult the user manual for the interface wheel).
To do so you need a motorized waste, which allows the IoT module to wirelessly open and
close the bath plug.
Shower processors:
Shower processors have a ‘warm-up’ function via the IoT, which eliminates the initial cold
water surge when a shower is rst switched on in the morning.
The warm-up function will allow the user to set a preferred temperature. The shower will turn
on and run until the correct temperature has been reached. The shower will then switch o
to conserve water. When the user turns the shower on via the main interface, the water will
be immediately available at the requested temperature.

2017-06
1 866 907 0122 blubathworks.com
6
Installation
1. Stick the WLAN module on the
designated place between battery and
AC adapter.
2. Connect t with the controller at the port
DISPLAY*.
*as the case maybe this port could be
marked RS-232 or WLAN.
Install the Netlevel module
Connect your Device (example shown: iPad®)
Start Settings App Go to Wi-Fi Settings and choose your
device’s network tlc-serial number (SN)
(The serial no. is printed on the side of the module)
STEP 1 STEP 2

2017-06
1 866 907 0122 blubathworks.com
7
STEP 3
Enter Password
(The password is printed on the side of
the module)
STEP 4
Open your Web Browser
STEP 5
Enter URL:
1.1.1.1
STEP 6
Operate your Twinlevel device as
per the instructions on page 10

2017-06
1 866 907 0122 blubathworks.com
8
Connect your Device (example shown: Galaxy Tab S®)
Start Settings App Go to Wi-Fi Settings and choose your device’s
network tlc-serial number (SN)
(The serial no. is printed on the side of the module)
STEP 1 STEP 2
STEP 3
Enter Password
(The password is printed on the side of the module)
STEP 4
Open your Web Browser

2017-06
1 866 907 0122 blubathworks.com
9
Connect your Device (example shown: Galaxy Tab S®)
STEP 5
Enter URL:
1.1.1.1
STEP 6
Operate your Twinlevel device as
per the instructions on page 10
Connect your Device to your Network
Select [Network]
Then choose your network
Enter the password of your network
Afterwards the device will connect automatically
with the webserver.
(on condition that your network is connected to the internet)
After connecting the page will be inactive and can
be closed.