Blueprint Controllers EZGrow Timer User manual

Thank you for choosing to grow with Blueprint Controllers! Your
satisfaction and success are important to us. For best results,
carefully read the following instructions before using your
Blueprint EZGrow Timer.
Using the Blueprint EZGrow Timer
Set Current Time of Day:
1. Press the “TIME SET” button once. The hour number will start flashing.
2. Press the buttons with the “up” and “down” arrows to set the hour.
3. Press the “TIME SET” button again. The minute number will start flashing.
4. Press the buttons with the “up” and “down” arrows to set the minutes.
5. Press the “TIME SET” button again. The AM/PM will start flashing.
6. Press the buttons with the “up” and “down” arrows to choose AM or PM.
7. Press the “TIME SET” button one last time to lock in the current time of day.
Set Cycle Start Time:
1. Press the “CYCLE SET” button once. The hour number will start flashing and the word
“CYCLE” will appear on the display to indicate you are setting the cycle start time.
2. Press the buttons with the “up” and “down” arrows to set the hour.
3. Press the “CYCLE SET” button again. The minute number will start flashing.
4. Press the buttons with the “up” and “down” arrows to set the minutes.
5. Press the “CYCLE SET” button again. The AM/PM will start flashing.
6. Press the buttons with the “up” and “down” arrows to choose AM or PM.
7. Press the “CYCLE SET” button one last time to lock in the cycle start time setting.
6/2012
AM
AM
AM
AM
AM
GROW
BLOOM
12/12
18/6
AM
PM
PM
AM
AM
Setting the 18/6 “Grow” or 12/12 “Bloom” Cycles:
1. For an 18ON/6OFF cycle, press the “GROW” button. The “GROW 18/6” icon will appear on
the left side of the time display. This cycle will power on device(s) plugged into the EZGrow
Timer at the programmed cycle start time and run for 18 hours. For the 6 hours thereafter,
device(s) plugged into the EZGrow Timer will not receive power and will turn off.
2. For a 12ON/12OFF cycle, press the “BLOOM” button. The “BLOOM 12/12” icon will appear
on the right side of the time display. This cycle will power on device(s) plugged into the
EZGrow Timer at the programmed cycle start time and run for 12 hours. For the 12 hours
thereafter, device(s) plugged into the EZGrow Timer will not receive power and will turn off.
When the Blueprint EZGrow Timer is in either cycle mode, the power indicator light will illuminate.
Resetting Blueprint EZGrow Timer:
Use a fine-tipped screwdriver or pen tip to press and hold the “RESET” button for two seconds. This will delete all previously programmed settings.
Battery Back-up
The battery back-up retains program settings in the event of a power outage. It will not continue to supply power to device(s) plugged into the
EZGrow Timer.
Features of your Blueprint EZGrow Timer
• LCD display
• Digital 24-hour timer
• Dual outlet capacity
• 125V, 15 amp, 1875 max wattage
• Rechargeable Ni-MH battery included
• 18/6 “Grow” or 12/12 “Bloom” integrated cycles
CYCLE
CYCLE
CYCLE

7854 North State Road 37
Bloomington, IN 47404
Phone: [phone]
Email: [email protected]
Sunleaves Garden Products
6/2012
Limited 1-Year Warranty Terms
Subject to the following limitations, Sunleaves Garden Products warrants that the Blueprint EZGrow
Timer, BET-2 will, for 1 (one) year from date of original retail purchase, but not exceeding two years
from date of manufacture, remain free from appearance of defects in workmanship or materials. This
warranty is subject to the following limitations: (a) manufacturer’s liability is limited to the replacement
or repair of the unit, as decided by the manufacturer; (b) a defective unit must be returned, prepaid,
with proof of purchase, to the point of purchase or as instructed below; and (c) this warranty does
not apply to defects resulting from the alteration, abuse, accidental damage, unauthorized repair, or
misuse of the unit. This warranty is given in lieu of all other warranties, guarantees, and conditions
on manufacturer’s part, and the manufacturer shall have no tortious or other liability in respect to this
Blueprint EZGrow Timer, BET-2.
Blueprint EZGrow Timer, BET-2 Warranty is Void if:
•NOTACCOMPANIEDBYORIGINALPROOFOFPURCHASE.
•BLUEPRINTEZGROWTIMERHASBEENUSEDINANON-STANDARDWAYINCLUDINGGENERALMISUSEANDOUTDOORUSE.
•  BLUEPRINT EZGROW TIMER HAS BEEN DAMAGED AS A RESULT OF ACCIDENT, IMPROPER INSTALLATION, ALTERATION, FIRE, FLOOD, OR
OTHER NATURAL DISASTER.
If the dealer is unable to resolve the problem:
1. Call our toll-free number at 888-464-9676 or email
[email protected] to receive warranty information.
2. In the event you must return the defective timer to Sunleaves,
carefully package the problem timer or timers.
3. Complete the form below and enclose it with your shipment
along with a legible copy of your properly dated sales receipt.
Because Sunleaves is not responsible for timers damaged in
shipping, we recommend insuring your package.
Don’t forget to include the following items if you are returning your Blueprint EZGrow Timer to the place of purchase:
•Legiblecopyofyourproperlydatedsalesreceipt
•Thiscompletedform
Name: ................................................................................................
Address: ..............................................................................................
Phone #: ..............................................................................................
Email Address: .........................................................................................
Explain the problem: ....................................................................................
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Blueprint 1-Year Limited Warranty
All Blueprint EZGrow Timers are protected against manufacturer defect by a limited 1-year manufacturer’s warranty.
Sunleaves Product Warranty Claims
To obtain warranty service, in the event that your Blueprint EZGrow Timer fails to operate, return the timer to the place of purchase. Often
times the dealer will be able to examine the timer in closer detail, determine the problem, and even fix it on site.