Mosquito Magnet PATRIOT PLUS User manual

PATRIOT PLUS
Operation Manual
Advanced Mosquito Defense Systems
• Customer Care Hotline: [phone]
• Online Assistance Available
• Certified Service Locations
Find out more at www.mosquitomagnet.com
Leader in 360º Customer Support
For Outdoor Use Only
1440-099
Woodstream Canada Corporation
25 Bramtree Court, Unit 1
Brampton, Ontario, Canada L6S 6G2
Tel: [phone] • www.mosquitomagnet.com
DOMESTIC - KEEP OUT OF REACH OF CHILDREN . READ THE LABEL BEFORE USING
Please retain these Operating Instructions for future reference. REG. NO. 32375 PCPA

Welcome
Congratulations on your purchase of Mosquito Magnet® .
Mosquito Magnet
®
Patriot is easy to use. The link www.mosquitomagnet.com/videos provides key information
for getting started. In this manual, you’ll learn everything you need to know about how it works, optimal trap
placement, maintenance, storage and warranty information. The keys to success are trap placement, utilization
of the correct attractant for your area and routine maintenance. For optimal catch rate, you’ll need to change the
propane tank and attractant every 21 days.
Our Customer Care line is available to answer all your questions regarding your new purchase.
Please feel free to contact us…
Customer Care: 1-800-953-5737
Woodstream® Canada Corporation
25 Bramtree Court, Unit 1
Brampton, Ontario
Canada L6S 6G2
Tel: [phone]
www.mosquitomagnet.com
Patents:
USA: Nos. 5,813,166; 6,145,243; 6,286,249; 6,817,140; 6,840,005;
6,848,466; 6,892,492; 7,074,830; 7,243,458; 7,281,351; 7,293,387;
7,536,824; 7,614,180; 7,752,803; and 7,987,631
Canada: Nos. 2,265,944; 2,322,038; and 2,460,876
Other patents pending
Made in China
1
FOR YOUR SAFETY
If you smell gas:
1. Shut off the gas to the appliance.
2. Extinguish any open ame.
3. Open lid.
4. If odor continues, immediately call your
gas supplier or your re department.
FOR YOUR SAFETY
1. Do not store or use gasoline or other
ammable vapors and liquids in the
vicinity of this or any other appliance.
2. An LP cylinder not connected for use
shall not be stored in the vicinity of this
or any other appliance.

Contents
2
3-4
5
6
Safety Instructions
PrincipleParts
Assembly Instructions
Set-Up 7-8
Trap Placement
Burying the Cord
Propane Tank Installation
Octenol Attractant Installation
Instructions 9
Starting Instructions
Shut Down Instructions
When Not In Use
End of Season Storage
For Best Results
Maintenance 10
Maintenance
Propane Tank Changing Tips
Maintenance Schedule
Troubleshooting 11
Warranty 12
Questions or Comments
Please contact Woodstream®Canada Corporation
if you have any questions or experience any
problems with your Mosquito Magnet®:
1-800-953-5737
Woodstream®Canada Corporation
25 Bramtree Court, Unit 1
Brampton, Ontario
Canada L6S 6G2
Tel: [phone]
www.mosquitomagnet.com
Patented Counterow Technology™
How the Mosquito Magnet
®
Patriot Plus Works
Mosquitoes use the long-range attractant carbon dioxide
(CO2) to locate people. Once in close proximity, mosquitoes
use short-range attractants such as scents emitted from the
skin, to determine which person they are going to bite. The
Mosquito Magnet
®
Patriot Plus mimics a human by converting
propane to CO2, with its patented catalytic conversion
technology, in combination with a short-range attractant.
Attracted by the CO2and short-range attractants, mosquitoes
and other biting insects are drawn to the Mosquito Magnet
®
Patriot Plus. When they reach the trap, the insects are
vacuumed into a bug bag by our patented Counterow
Technology™, where they dehydrate and die within 24 hours.
The Mosquito Magnet
®
Patriot Plus is silent and odorless.
When properly placed in your yard, the trap begins
working immediately. Noticeable results can be
achieved in 7 to 10 days. To greatly reduce your biting
insect population, allow 4 weeks. Leave the Mosquito
Magnet
®
Patriot Plus out all summer long, to control the
mosquito population in your yard.
Model No.:
Serial No.:
Type of Gas:
Manifold Pressure:
Minimum Gas
Supply Pressure:
Input Rating:
Minimum Clearances:
Patriot Plus
Propane
2.7 kPa (11'WC)
2.7 kPa (11'WC)
650 kJ/Hr. (759 Btu/Hr)
50-60 cm (20 – 24")

3
Safety Instructions
Please read and follow all safety
instructions and warnings.
Children and adults should be alerted to
the hazards of high surface temperatures
and should stay away to avoid burns or
clothing ignition.
Note: Some or all of the following required safety
instructions for propane powered devices may
apply to your trap. Allow trap to cool for 5 minutes
before re-starting.
Warning: Improper installation, adjustment,
alteration, service or maintenance can cause injury
or property damage. Read the installation, operating
and maintenance instructions thoroughly before
installing or servicing the trap.
Caution: The gas pressure regulator provided with this
appliance must be used. This regulator is set for an outlet
pressure of 2.7 kPa (11’ WC). The minimum inlet gas
supply pressure is 2.7 kPa (11’ WC) from regulator.
• This unit is not intended to be installed in or on recreational
vehicles and/or boats.
• The gas supply must be turned off at the LP-Gas supply cylinder
when this appliance is not in use.
• The installation must conform with local codes or, in the absence
of local codes, with the National Fuel Gas Code,
ANSI Z223. 1-1998 for US and with the CAN1-B149 for Canada.
•To test for a gas leak, place soapy water around the
connector, regulator, and gas hose assembly. If bubbles
appear, there is a gas leak.
• Inspect the hose before each use of the unit. If it is evident there
is excessive abrasion or wear, or the hose is cut, it must be
replaced prior to the unit being put into operation. The
replacement hose shall be that specified by the manufacturer.
• The trap is equipped with an internal spark ignition device. Failure
to follow starting procedure will result in the trap not starting.
• Installation and repair should be done by a qualified service
person (find service centers on www.mosquitomagnet.com). The
heater should be inspected before use and at least
annually by a qualified service person. More frequent
cleaning may be required as necessary. It is imperative that
the control compartment, burners, and circulating air
passageways of the trap be kept clean.
Young children should be carefully
supervised when they are in the
area of the trap.KEEP OUT OF
REACH OF CHILDREN.
Clothing or other flammable materials
should not be hung from the trap, or
placed on or near the trap.

4
Safety Instructions
• Maintain adequate clearances of 50-60 cm (20”-24”)
around air openings into the combustion chamber, clearances
from combustible material, provisions for accessibility and for
combustion and ventilating air supply. Keep the trap area clear
and free from combustible materials, gasoline, and other
flammable vapors and liquids. The appliance is not to be used
in locations where flammable vapor or explosive dust is likely to
exist.
• Do not obstruct the flow of combustion and ventilation air.
• Keep the ventilating openings of the cylinder enclosure free
and clear from debris.
• Clean the trap with a damp cloth, if necessary.
• A maximum of a 9 kg (20 lb.) LP-Gas cylinder shall be used.
• The LP-Gas cylinder must be provided with a shut-off valve
terminating in an LP-Gas supply cylinder valve
outlet specified for Connection No. 510 in the Standard for
Compressed Gas Cylinder Valve Outlet and Inlet Connections,
ANSI/CGA-V-1-1977.
• The LP-Gas cylinder supply system must be arranged for
vapor withdrawal and the cylinder must include a collar to
protect the cylinder valve.
• The LP-Gas cylinder used shall be constructed and marked
in accordance with the specifications for LP-Gas cylinders of
the U.S. Department of Transportation (DOT) or The National
Standard of Canada CAN/CSA-B339.
• The trap shall be used outdoors only in a well ventilated
space and shall not be used in a building, garage, or any other
enclosed area.
• The LP-Gas cylinder must be disconnected and removed
from the appliance, if the appliance is stored indoors.
• LP-Gas cylinders must be stored outdoors in a well-
ventilated area out of reach of children.
• Disconnected cylinders must have threaded valve plugs
tightly installed and must not be stored in a building, garage, or
any other enclosed area.
• The pressure regulator and hose assembly supplied with
this appliance must be used for connection to the LP-Gas
cylinder. Replacement pressure regulators and hose
assemblies must be specied by the manufacturer.
• Avoid improper use of extension cords. Keep connections
away from moisture and avoid damage to the cord.
• If the supply cord is damaged, it must be replaced by the
manufacturer or its service agent or a similarly qualied
person in order to avoid hazard.
Please contact Customer Care
if you have any questions at:
1-800-953-5737
or visit www.mosquitomagnet.com
Warning: SHOCK! An electric shock hazard
may exist if water from a garden hose is directed at
the Mosquito Magnet® Patriot. Route the power cord in the
safest possible manner to avoid personal injury.

5
Principle Parts
Mosquito Magnet®
Patriot Plus
Parts Included
Base Propane
Tank Cradle (1)
Bug Bag
Already
Installed
10 Metal Power Cord
Burying Clips
Mosquito Magnet®Octenol
Mosquito Attractant Cartridge
(added attractant)
15 m (50') Power Cord
Power Head (1)
Trumpet (1)
Support Pole (1)
Support Leg (1)

6
Assembly Instructions
Step 1
Place base upside down on a at
surface, slide U-shaped support
legs into slots on base until they
lock in place.
Step 5
Insert attractant as directed in
attractant packaging.
Step 2
Turn base and leg assembly
right-side-up and place support
pole into cavity on base.
Step 6
Place the base of the propane
tank into the molded cradle
supplied.
Step 9
Plug Adapter into properly
grounded electrical outlet.
Step 3
Place trap power head onto
pole. Press down rmly with two
hands to secure.
Step 7
Making sure propane tank is fully
closed, attach propane regulator
hose to propane tank. Secure
tightly by hand. Do not use tools.
Step 10
Turn propane valve on slowly.
See page 8 for propane tank
installation.
Step 4
Completed assembly should have
the front of power head in the same
direction as base U-shaped legs.
Step 8
Plug power connector into the
trap power slot located on the
back of the power head.

7
Set-Up
Trap Placement
1. Determine the direction of the prevailing wind.
Check local weather patterns if you are unsure.
2. Stand in the center of the area you are trying to protect
and look toward the prevailing wind.
3. Proper placement of the trap will be 9-12 m (30-40 ft.) in
front of you, within 1.5-1.8 m (5-6 ft.) of mosquito habitat
(i.e., standing water, bushes, owerbeds, treeline, marshbed,
etc.). Ensure that trap is not directly against any blockades
such as buildings, fences, etc.
4. It is recommended that the trap be placed in the shade.
5. Do not place trap directly above a water source
(sprinklers, hose, etc.).
6. Trap must be placed on level ground to avoid tipping
or uneven propane distribution.
7. Go to www.mosquitomagnet.com to build your own yard
diagram.
Burying the Power Cord
Make sure unit is unplugged and in proper position. Use the
Cord Burying Clips supplied. Place clips approximately
1 m (3 feet) apart, press into ground by hand making sure not
to damage power cord. For alternate placement, follow steps
illustrated below.
1. Use straightedge shovel or garden spade and dig a trench
about 8-10 cm (3”-4”) deep from power source to trap.
2. Place cord into trench carefully stretching as you go to
remove any twists in cord.
3. Use cedar shingle or folded cardboard to place cord into
bottom of trench. Recover the trench with removed soil.

8
Set-Up
Propane Tank Installation
1. After trap is placed in its ideal location, place propane
tank onto the molded cradle.
2. Make sure propane tank is fully closed. Attach
propane regulator hose to propane tank. Secure
tightly by hand. Do not use tools.
3. Turn propane on by slowly turning valve counter-clockwise.
Take care not to turn too quickly to avoid engagement of
safety valve.
DO NOT MOVE TRAP WITH TANK ATTACHED!
TANK MUST BE DISCONNECTED FROM REGULATOR
BEFORE TRAP IS RELOCATED TO AVOID DAMAGE TO
REGULATOR AND/OR TRAP. BE ADVISED, DAMAGE
CAUSED FROM FAILURE TO COMPLY WITH THIS
INSTRUCTION IS NOT COVERED UNDER WARRANTY.
Octenol Attractant Installation
See Mosquito Magnet®Octenol Mosquito Attractant label for
installation, use, storage and disposal instructions.
Step 1 - Propane Tank Placement
Step 2 - Attach Regulator
Step 3 - Slowly Open Valve

9
Instructions
**READ MANUAL BEFORE STARTING**
Starting Instructions
It is recommended that you read the entire manual
before starting the Mosquito Magnet®Patriot Plus trap.
1. Insert attractant in compartment per instructions in
attractant packaging.
2. Connect regulator to propane tank
(See the Propane Tank Installation section).
3. Plug power connector into the trap.
4. Plug AC adapter into electrical socket. (To avoid the
risk of electrical shock, connect only to properly
grounded outlets.) Adapter unit is not intended to be
mounted.
5. Slowly turn propane tank valve on.
6. Turn rocker switch to “on” position.
7. The red light on the switch will ash for up to 20
minutes (warm up phase).
8. Once the light stops ashing and is solid, the Mosquito
Magnet®Patriot Plus is fully operational.
NOTE: Should you experience an interruption of power,
be sure to restart trap.
Shut Down Instructions
To shut down the Mosquito Magnet®Patriot Plus simply
close the valve on the propane tank and switch to the “off”
position.
When Not In Use
If the unit is not in use, the gas must be turned off at the
supply cylinder. Storage of this unit indoors is permissible only
if the cylinder is disconnected and removed. Cylinders must
be stored outdoors, out of reach of children and must not be
stored in a building, garage or any other enclosed area.
End of Season Storage
Push ON/OFF switch to OFF position to shut down the trap.
The LED light will go out and the fan will continue running
until trap is cool. Close the propane tank valve
and disconnect regulator.
Any open Mosquito Magnet®Octenol Mosquito Attractant
should be removed and discarded. See attractant label for
disposal instructions. The bug bag should also be discarded
prior to storing the trap.
For Optimal Results (unit must run for 24 hours/day)
• Allow trap to cool for 5 minutes before re-start.
• Never spray insecticide in or around trap.
• Trap can be left running in the rain.
• If using lime or fertilizer compounds, be sure to shut
down the trap first to prevent dust or fine mist from
being drawn into trap and clogging bug bag.
Warning: Improper installation, adjustment, alteration,
service or maintenance can cause injury or property
damage. Read the installation, operating and
maintenance instructions thoroughly before installing
or servicing this equipment.
Caution: The gas pressure regulator provided with this
appliance must be used. This regulator is set for an
outlet pressure 2.7 kPa (11.0’ WC).
The gas supply must be turned off at the LP-Gas
supply cylinder when this appliance is not in use.
Leader in 360º Customer Support
• Customer Care Hotline: [phone]
• Online Product Registration Available
• Certified Service Locations – Information Available
at www.mosquitomagnet.com
STORAGE: The trap should be stored indoors in a garage
or shed in the off-season. Cover trumpet to prohibit insects from
nesting. Cover unit with a trap and secure tightly at the bottom to
keep out dust, spider webs and other debris.

10
Maintenance
Maintenance
•21 Day Maintenance Cycle
- Refill propane. (Propane lasts approximately 21 days with
24-hour/7-days operation.)
- Replace short-range attractant cartridge.
See Mosquito Magnet®Octenol Mosquito Attractant
label for instructions.
- Empty or replace bug bag.
•Periodically wipe down the outside of the trap
with a clean, damp cloth.
Propane Tank Changing Time
When attaching the regulator knob to a tank after a tank
change, be sure to fully tighten the regulator knob onto the
tank. No need to use tools, but do turn the knob as far as
possible by hand. When this is done, loosen the knob 1/4 turn,
then re-tighten to maximize seal.
The purpose for this is to fully engage the regulator onto the
tank. If the regulator is not fully engaged, the flow of gas
may be restricted to the point where the trap will show a gas
empty code. If this occurs, press the off button, close the tank
valve, and remove the regulator from the tank. Re-attach the
regulator and try again.

11
Troubleshooting
Problem
Your Mosquito Magnet®
Patriot Plus won’t start
Your Mosquito Magnet®
Patriot Plus won’t start
Low or no catch
Possible Cause Solutions
1. Is the propane tank empty?
2. If propane tank is new, it may have
air blockage, has it been purged?
3. If tank has been opened too quickly, security
check valve may have triggered.
4. Is the power cord plugged in?
5. Is there a loose connection?
1. The tank regulator isn’t fully engaged.
2. Propane tank may be empty or need to be
purged.
3. Regulator is not fully engaged.
1. Insects may not be out yet.
2. Trap improperly placed.
3. Biting insects reproductive cycles have not
yet been broken.
Customer Care **Please have your serial number, date of purchase & model type available**
All of us at Woodstream®Corporation want you to get complete satisfaction from your trap. Should you have any problems you cannot
resolve, simply call one of our trained Customer Service Representatives at 1-800-953-5737 or visit www.mosquitomagnet.com.
We will help you get up and running.
1. Weigh tank and check against “empty” weight
written on tank.
2. Bring tank to lling location. Air may be in
fuel line. Ask for tank to be purged.
Hint: If you have another propane powered
device operating on a standard, 9 kg (20 lb)
propane tank, try hooking that tank up to the trap
to verify that the issue is with your tank.
3. Disconnect the regulator from the tank and
reconnect. Then open the regulator valve slowly.
4. Verify all electrical connections. Make sure you are
using the correct power requirements for your unit.
5. Make sure regulator is fully engaged, and propane
tank valve is fully open.
1 . Make sure the regulator is fully engaged, and
propane tank valve is fully open.
2. Go through above steps 1, 2 and 3.
3. See Tank Changing Tips section. Hand
tighten the propane tank regulator until
slightly snug.
1. Verify temperature is consistently above 50˚F (10˚C).
2. Follow steps in the “Trap Placement” section of
your owner’s manual or go to
www.mosquitomagnet.com “Placement” section.
3. Keep trap in constant operation 24 hours/day,
7 days/week for 4 weeks to interrupt the
breeding cycle.

12
Limited Warranty
Limited Warranty
This warranty, (1) year from the purchase of
the unit, is extended only to the original
purchaser/user of products. This limited
warranty begins on the original date of
purchase, and is valid only on products
purchased and used in the United States.
Woodstream®Canada Corporation warrants its
products to be free from defects in materials
and workmanship for the warranty period by
the original purchaser/user.
For warranty service, please contact our
Customer Care [phone]. Please indicate
the nature of the defect. Warranty service can
only be performed by a Mosquito Magnet®
Certied Service Center.
If Woodstream®Canada Corporation determines
there may be a defect, Woodstream®Canada
Corporation will issue a Return Goods
Authorization (RGA) number. The defective
unit or parts must be returned for warranty
inspection using the
RGA number, when applicable, as identication
within (30) days of return authorization date.
DO NOT return products to our factory without
our prior consent, as they, as well as
C.O.D. shipments will be refused. Woodstream®
Canada Corporation or agent, at its option, shall
replace the unit, replace the defective part(s)
and return such unit to you. Woodstream®
Canada Corporation’s sole obligation and your
exclusive remedy under this warranty shall be
limited to such replacement.
Limitations and Exclusions:
The warranty shall not apply to problems arising
from normal wear, or failure to adhere to the
enclosed instructions. In addition, the foregoing
warranty shall not apply to serial numbered
products if the serial number has been removed
or defaced; products subject to negligence,
accident, improper operation, maintenance or
storage; products damaged by circumstances
beyond Woodstream®Canada Corporation’s
control; or products modied (including, but
not limited to modications through the use of
unauthorized parts or attachments) or repaired
by anyone other than Woodstream
®
Canada
Corporation or its designee.
The foregoing warranty is exclusive and in lieu
of all other warranties, express or implied,
including without limitation the implied
warranties of merchantability and tness for a
particular purpose. It shall not extend beyond
the duration of the express warranty provided
herein, and the remedy for violations of
any warranty shall be limited to repair or
replacement of the defective product pursuant
to the terms contained herein. Woodstream®
Canada Corporation shall not be liable for any
consequential or incidental damages whatsoever.
This warranty gives you specic legal rights
and you may also have other legal rights
which may vary based on location.

PATRIOT PLUS
Manuel de l’utilisaeur
Systèmes de Défense Avancés Contre les Moustiques
• Serviceà la clientèle:1-800-953-5737
• Assistanceen ligne disponible
• Les lieux de service certiés
Chef de le en soutien 360°
Pour usage à
l’extérieur seulement.
1440-099
Woodstream Canada Corporation
25 Bramtree Court, Unit 1
Brampton, Ontario, Canada L6S 6G2
Tel: [phone] • www.mosquitomagnet.com
DOMESTIQUE - GARDER HORS DE LA PORTÉE DES ENFANTS.
LIRE L’ÉTIQUETIE AVANT D’UTILISER
Veuillez conserver ce manuel d’utilisation pour référence ultérieure.
N° D’ENR. 32375 LPA

Bienvenue
Félicitations pour votre achat de Mosquito Magnet® Patriot.
Soutenu par 18 années de recherche et de d’essais indépendants, ii est scientiquement prouvé que
Mosquito Magnet® Patriot capture et tue les moustiques.
Mosquito Magnet®Patriot est facile à utiliser. Le lien www.mosquitomagnet.com/videos fournit des informations
clés pour la mise en route. Dans ce manuel, vous apprendrez tout ce que vous avez besoin de savoir sur son
fonctionnement, le meilleur emplacement du pièges, la maintenance, l’entreposage et la garantie. Les clés du succès
sont l’emplacement du piège, l’utilisation de l’appât adéquat pour votre région et de maintenance routine. Pour le
taux de capture optimal, vous aurez besoin de changer le réservoir de propane et l’appât taus les 21 jours.
Notre service à la clientèle en ligne est disponible pour répondre à toutes vos questions concernant
votre nouvel achat. N’hésitez pasà nous contacter ...
Service à la clientèle: 1-800-953-5737
Woodstream® Canada Corporation
25 Bramtree Court, Unit 1
Brampton, Ontario
Canada L6S 6G2
Tel: [phone]
www.mosquitomagnet.com
Brevets:
États Unis: Nos. 5,813,166; 6,145,243; 6,286,249; 6,817,140;
6,840,005; 6,848,466; 6,892,492; 7,074,830; 7,243,458; 7,281,351;
7,293,387; 7.293.387; 7.536.824; 7.614.180; 7.752.803; 7.987.631
Canada: Nos. 2,265,944; 2,322,038; 2,460,876
Autres brevets en instance
Fabriquè en Chine
1c
POUR VOTRE SÉCURITÉ
Si vous sentez une odeur de gaz:
1. Coupez l’alimentation de gaz de l'appareil.
2. Éteignez toute amme nue.
3. Ouvrez le couvercle.
4. Si l’odeur persiste, appelez immédiatement
votre fournisseur de gaz ou votre service
d’incendie.
POUR VOTRE SÉCURITÉ
1. Ne pas entreposer ni utiliser d’essence ou
autres vapeurs et liquides inammables à
proximité de cet ou tout autre appareil.
2. Une bouteille de propane non branchée
ne doivent pas être entreposées à
proximité de cet ou tout autre appareil.

Table des Matières
2c
Consignes de sécurité 3c-4c
Pièces principales 5c
Consignes d’assemblage 6c
Assemblage du piège
Installation 7c-8c
Emplacement du piège
Enterrer le cordon d’alimentation
Installation d’un réservoir de propane
Installation d’appât d’octenol
Instructions 9c
Consignes de démarrage
Consignes d’arrêt
Lorsqu’il n’est pas utilisé
Entreposage à la n de la saison
Pour des résultats optimaux
Entretien 10c
Calendrier d’entretien
Réservoir de propane Conseils de changement
Guide de Dèpannage 11c
Garantie 12c
Duestions ou commentaires
S’il vous plaît contacter Woodstream®Canada Corporation
Corporation si vous avez des questions ou rencontrez
des problèmes avec votre Mosquito Magnet® :
1-800-953-5737
Woodstream®Canada Corporation
25 Bramtree Court, Unit 1
Brampton, Ontario
Canada L6S 6G2
Tel: [phone]
www.mosquitomagnet.com
Technologie brevetée Counterow Technology™
Fonctionnement du Mosquito Magnet® Patriot Plus
Les moustiques utilisent l’appât a longue portée dioxyde de
carbone (C02) pour localiser les personnes. Une fois à proximité,
les moustiques utilisent les appâts à courte portée comme les
odeurs émises par la peau, pour déterminer quelle personne elles
vont mordre. Le Mosquito Magnet®Patriot Plus imite une personne
par la conversion du propane en C02, grâce à sa technologie
brevetée de conversion catalytique, en combinaison avec un appât
à courte portée.
Attirés par le CO2et les appâts à courte portée, les moustiques sont
attirés par le Mosquito Magnet® Patriot Plus. Quand ils atteignent
le piège, les moustiques sont aspirés dans un sac à insectes par
notre technologie brevetée CounterFlow™, où ils se déshydratent et
meurent dans les 24 heures.
Le Mosquito Magnet® Patriot Plus est silencieux et sans odeur.
Lorsqu’il est correctement placé dans votre cour, le piège commence
à travailler immédiatement. Résultats observables peuvent être
obtenues en 7 à 10 jours. Pour réduire considérablement votre
population d’insectes piqueurs, permettre à 4 semaines. Laissez
le Mosquito Magnet® Patriot Plus sur tout l’été, an de contrôler la
population de moustiques dans votre cour.
Modele n °:
N ° de série:
Type de gaz:
Pression d’admission:
Pression minimum
d’a/imentation en gaz:
Consommatin
thermique:
Dégagements minimum:
Patriot Plus
Propane
2,7 kPa (11 ‘WC)
2,7 kPa (11 ‘WC)
685 kJ / Hr. (759 Btu / h)
50-60 cm (20 à 24 “)

3c
Consignes de Sécurité
S’il vous plaît lisez et suivez toutes les
consignes et avertissements de sécurité.
Les enfants et les adultes doivent être
avertis des risques liés à une température
de surface élevée, et demeurer loin de
celle-ci pour éviter des brûlures ou la
combustion de leurs vêtements.
Nota: Certaines ou toutes les consignes de sécurité suivantes
concernant les appareils alimentés au propane peuvent
s’appliquer à votre piege. Laisser le piège se refroidir
pendant 5 minutes avant de redémarrer.
Avertissement: Toute installation, modication, altération, ou
procédure de réparation ou d’entretien inadéquate peut causer
des blessures ou des dégâts matériels. Lire les consignes
d’installation, d’utilisation et d’entretien avant d’installer ou de
réparer cet appareil.
Attention: Le régulateur depression de gaz fourni avec cet
appareil doit être utilisé. Ce régulateur est réglé pour une
pression de sortie de 2,7 kPa (11 po WC). La pression d’entrée
minimum d’approvisionnement en gaz est de 2,7 kPa
(11 po WC) du régulateur.
• Cet appareil n’est pas destiné à être installé dans ou sur
les véhicules récréatifs et / ou des bateaux.
• L’approvisionnement en gaz doit être coupé à la
bonbonne de gaz lorsque cet appareil n’est pas utilisé.
• L’installation doit être conforme aux codes locaux au, en
l’absence de codes locaux, avec le National Fuel Gas
Code, ANSI Z223. 1-1998 pour les États Unis et au CAN1-B149
pour le Canada.
• Pour vérier la présence d’une fuite de gaz, mettre de
l’eau savonneuse autour du connecteur, du régulateur, et
du tuyau de gaz. Si des bu lies apparaissent, il ya une fuite de gaz.
• lnspectez le tuyau avant chaque utilisation de l’appareil.
S’il est évident qu’il ya de l’abrasion au une usure
excessive, ou si le tuyau est coupé, il doit être remplacé
avant de faire fonctionner. La tuyauterie de rjn emplacement
doit être celle spéciée par le constructeur.
• Le piège est équipé d’un dispositif d’allumage avec une
étincelle intérieure. Le non respect de la procédure de
démarrage peut nuire au démarrage du piège.
• L’installation et la réparation doivent être effectuées par
une personne qualiée (trouver des centres de service
sur www.mosquitomagnet.com). L’appareil de chauffage
doit être inspectéavant l’utilisation et au mains
annuellement par une personne qualiée. Un nettoyage
plus fréquent peut être nécessaire. II est impératif que le
compartiment de contrôle, les brûleurs et les conduits
d’air de l’appareil de chauffage soient gardés prop res.
Les jeunes enfants doivent être supervisés
soigneusement lorsqu’ils se trouvent
à proximité de l’appareil de chauffage.
GARDER HORS DE LA PORTÉE DES ENFANTS.
Les vêtements ou autres matières
inammables ne doivent pas être
suspendues sur l’appareil de chauffage
ou placés sur ou à proximité de celui-ci.

4c
Consignes de Sécurité
• Maintenir des espaces de dégagement adéquats de
50-60 cm (20 “-24”) autour des orices de ventilation
dans la chambre de combustion, les dégagements des
matériaux combustibles, des dispositions
d’accessibilité et d’alimentation en air de combustion
et de ventilation. Garder la zone de piège claire et
exempte de matériaux combustibles, essence et
autres vapeurs et liquides inammables. L’appareil ne
doit pas être utilisé dans des endroits où des vapeurs
inammables ou des poussieres explosives peuvent exister.
• Ne pas obstruer le conduit d’air de combustion et de ventilation.
• Garder les ouvertures de ventilation de l’enceinte de la
bouteille libres et exemptes de débris.
• Nettoyer le piège avec un chiffon humide d’eau, si nécessaire.
• Une bonbonne de gaz de 9 kg (20 lb) maximum doit être utilisé.
• La bonbonne de gaz doit être munie d’un robinet
d’arrêt au bout des conduits d’écoulement de la
bonbonne de gaz qui est conçu pour une connexion n°
510 selon la norme sur les raccords d’entrée et de
sortie de vanne de bouteilles à gaz comprimé,
ANSI/CGA-V-1-1977.
• Le système d’alimentation de la bonbonne de gaz doit
être adapté pour le retrait de vapeur et le cylindre doit
avoir un collet pour protéger le robinet de la bouteille.
• La bonbonne de gaz utilisée doit être fabriquée et
identiée conformément aux spécications pour les
bouteilles de propane de la Norme nationale du
Canada CAN/CSA-8339.
• Le piège doit être utilisé à l’extérieur seulement dans
un espace bien aéré et ne doit pas être utilisé dans un
bâtiment, un garage ou tout autre endroit fermé.
• La bonbonne de gaz doit être débranchée et retirée de
l’appareil, si l’appareil est entreposé a l’intérieur.
• Les bonbonnes de gaz doivent être entreposées à
l’extérieur dans un endroit bien aéré hors de la portée
des enfants.
• Les cylindres débranchés doivent comporter des
ches de vannes letées bien installées et ne doivent
pas être entreposés dans un bâtiment, un garage ou
tout autre endroit fermé.
• Le régulateur depression et le raccord de tuyau
fournis avec cet appareil doivent être utilisés pour la
connexion à la bonbonne de gaz. Le remplacement des
régulateurs de pression et des raccords de tuyaux
doivent être spéciée par le constructeur.
• Éviter l’usage inadéquat des rallonges. Garder les
connexions loin de l’humidité et d’éviter
d’endommager le cordon.
•Sile cordon d’alimentation est endommagé, il doit être
remplacé par le fabric ant ou son agent de service ou
une personne qualiee an d’éviter tout danger.
S’il vous plaît contacter le service client
si vous avez des questions au:
1-800-953-5737
or visit www.mosquitomagnet.com
Attention: CHOC! Un risque de choc électrique
peut exister si l’eau d’un tuyau d’arrosage est dirigée
vers le Mosquito Magnet®Patriot Plus. Placer le cordon
d’alimentation le plus sécuritairement possible an d’éviter
les blessures.

5c
Pièces Principales
Mosquito Magnet®
Patriot Plus
Pièces Incluses
Berceau sur la base
pour le reservoir
de propane (1)
Tête mécanique (1)
Trompette (1)
Perch de maintien (1)
Pied-support (1)
10 Brides de Cordon en
Métal
Mosquito Magnet®appât à
l'octenol Mosquito Cartouche
(Appât Ajouté)
Sac à insectes
Déjà Installé
Cordon d’alimentation
15 m (50 ‘)