BOERPLAY Water play St. Lucia with Pump User manual

Water play St. Lucia with Pump
(Ground water (pulse) connection)
PSTE801.001
Powered by TCPDF (www.tcpdf.org) 1 / 1

Benaming
Title
Opmerking
Comment
Datum
Date
Tekening
Drawing
TOE PST 801 001
E
Water combinatie
Pomp-goot-bak
13-3-2023
Hoofdafmetingen Main dimensions
0,00 m
0,23 m
0,70 m
1,35 m
0,00 m
0,24 m
0,50 m
0,00 m 1,73 m 3,78 m 5,01 m
0,00 m
0,47 m
0,86 m
1,52 m

Benaming
Title
Opmerking
Comment
Datum
Date
Tekening
Drawing
TOE PST 801 001
E
Water combinatie
Pomp-goot-bak
13-3-2023
Obstakelvrije zone Obstacle free zone
Obstakelvrije zone
Obstacle free zone
Opvangzone
Impact area
8,08 m
4,54 m
R1,50m
R1,50m
R1,50m
R1,50m
R1,50m
R1,50m
3,48 m
5,76 m

Benaming
Title
Opmerking
Comment
Datum
Date
Tekening
Drawing
TOE PST 801 001
Water combinatie
Pomp-goot-bak
13-3-2023
Bodemplan Groundplan
E
0,72 m
2,02 m 0,88 m 1,42 m
0,34 m
0,63 m 1,56 m
2,00 m0,53 m1,61 m1,02 m
1,83 m
1,28m
0,84m
0,50m
0,12m
1,00 m
0,12 m
Grondmarkering
Ground level marker

Benaming
Title
Opmerking
Comment
Datum
Date
Tekening
Drawing
TOE PST 801 001
Water combinatie
Pomp-goot-bak
13-3-2023
Montage Mounting
E
OpmerkingBenamingRev.Bew.Volgnr.Progr.Type
#
Nr.
RobiniaWatergoot RechtC110013PSTMOD
11
130 x 90 cmPomp londer
B
258013PSTMOD
1
2
H=900
Polyester waterbak
C259013PSTMOD13
Geleverde delen:
Zie tabel
Montagevolgorde:
1 - Graaf de gaten volgens het bodemplan
2 - laats 1
3 - laats 2 en 3
4 - Controleer of het toestel voldoet aan de afmetingen zoals op blad 'afmetingen'
5 - Dicht de gaten en verdicht het zand
Controles:
1 - Correcte opbouw en alle bevestigingsmiddelen
2 - Zorg dat de uiteinden van de watergoot het water goed opvangen en geleiden
3 - Controleer de afmetingen van de valbodem t.o.v. het toestel
Supplied parts:
See table
Assembly sequence:
1 - Dig the holes according to the ground plan
2 - lace 1
3 - lace 2 and 3
4 - Check that the equipment conforms to the dimensions shown on sheet 'dimensions'
5 - Close the holes and compact the sand
Checks:
1 - Correct assembly and all the fasteners
2 - Make sure the ends of the gully collect and guide the water properly
3 - Check the dimensions of the safety area compared to the play equipment
Typeplaatje
Identification plate
B
3
1
2

LOGBOOK
Type indication Adventure Play
Article number PSTE801.001
Product Name Water play St. Lucia with Pump (Ground water (pulse) connection)
Maximum fall height 0,7 m
Construction year 2023
Certificate 065599
Inspection body TUV Nederland QA BV
Ekkersrijt 4401
5692 DL Son
Manufacturer name Boer Speeltoestellen
Hyacintstraat 2 - 4255 HX Nieuwendijk
Phone: [phone]
Fax: [phone]
Installer name _______________________________________________________
_______________________________________________________
_______________________________________________________
Playground location _______________________________________________________
Information about the owner of the playground
Name: _______________________________________________________
Address: _______________________________________________________
Zipcode and city: _______________________________________________________
Contact: _______________________________________________________
Phone number: _______________________________________________________
Information about the manager of the playground
Name: _______________________________________________________
Address: _______________________________________________________
Zipcode and city: _______________________________________________________
Contact: _______________________________________________________
Phone number: _______________________________________________________
Powered by TCPDF (www.tcpdf.org)

LOGBOOK
Inspection and maintenance
Date of
inspection
maintenance
Time of
inspection
maintenance
Name
executor of
inspection
Name
executor of
maintenance
Found defects Parts to be
replaced
Accidents
Date
accident
Age of
victim Probable cause of injury Occurred injury Measures taken after accident

Inspection and maintenance intervals
Nr Inspection Maintenance
months
between
inspections
1
Verify equipment's stability, junctions and
missing parts Inspect bolts, screws and nuts for
absence, jams, corrosion and wear
Add missing parts, secure joints, apply
missing fixing agent and replace
corroded parts
1
2
Check suspension for wear Replace worn parts and/or remove non-
functioning parts
1
3
Inspect rotating parts such as hinges, rolling-
element bearings, etc for wear and acceptability
Replace worn parts and/or remove non-
functioning parts
1
4
Check wood for splinters, unacceptable damage
and signs of rot, especially at ground level
Repair damage Replace affected wood
Smoothen splintered wood and sharp
edges
1
5
Inspect foundation for stability, tearing and
coverage
Restore foundation and covering
material
3
6
Examine rubber and synthetic parts for wear,
damage and breakage Replace for OEM original parts
3
7
Examine fibre reinforced plastic parts, especially
slides, for wear
Replace for OEM parts if the fibres are
visible
6
8
Inspect metal for corrosion and damage in the
coating
Restore any damaged coating (after
removing rust and applying primer)
6
9
Check ropes, cables, chains and nets for wear
and damage Steel cables and nets which are
tensioned must be checked for tension
Replace parts where necessary Steel
cables and nets must be tensioned
3
10
Inspect equipment for unsafe changes and
additions
Remove unsafe additions and correct
unsafe changes
1
11
Inspect safety surfaces Restore and repair where necessary
1
Remarks
1 If used intensively, all points require extra attention
2 Extreme weather conditions and locations may require a higher inspection frequency Discuss this with the
supplier
3 Vandalism-sensitive locations require stricter inspections, possibly daily
4 Re-tighten all connections in Robinia equipment two months after first use
5 Re-span spatial networks two months after first use
6 Check the terrain regularly for items that do not belong there, are unsafe or may be used wrongly Examples
are poisonous plants, glass shards, etc Frequency depends on strain

7 Remember that bad maintenance leads to unsafe conditions and notably faster impoverishment of the
playground area
8 Replacement parts can be ordered at the manufacturer with the OEM part numbers on the module drawing
Drawings can be found in the user guide
9 The impact area shall be provided with impact attenuating surface according to the specified falling height
•Up to 0,6m height of fall: no requirements regarding impact attenuation
•Turf, topsoil: suitable up to 1000mm height of fall
•Loose fill (sand, gravel, bark, woodchips): up to 3000mm height of fall Layer thickness is height
of fall / 10 +100mm, with a minimum of 300mm
•Synthetic surfaces (Rubber tiles, artificial turf, wetpour, tigermulch etc ): height of fall and layer
thickness according to the information of the supplier
10 This list is conform the CEN-standard "playground equipment and surfacing NEN-EN 1176-7"
Improving the
foundations
(for equipment without concrete in the standard
foundation)
If the impact area is loose fill (sand, gravel, bark,
woodchip, etc ), or if the soil itself does not add to
stability of the equipment (i e sand, pumice, peat soil)
pour 50l of concrete per post
For instance:
Square: 0,6 x 0,6 x 0,16m
Round: ø0,35 x 0,5m
Round: ø0,50 x 0,2m

A ( 1 : 2 )
Benaming
Title
Opmerking
Comment
Datum
Date
Tekening
Drawing
MOD PST 013 259
Polyester waterbak
H=900
16-5-2022
Samenstelling module Assembly module
C
Opmerking
BenamingRev.Bew.
Volgnr.
Progr.Type#Nr.
4 x 25 - RVS A2-70
Schroe Assy
025004002BSR81
5 x 70 - RVS A2-70
Schroe Assy
070005002BSR362
M10 x 55 - RVS A2-70
Draadeind
055010070BSR13
H = 38 m10
Draaiknop Ø 40
060040BOLKST24
Lengte = 1000
Standaard plank 120x20
100211PSTOHO2
5
Lengte = 600
Standaardplank 120x30
060221PSTOHO26
Lengte = 800Standaardplank 120x30 080221PSTOHO6
7
900 mm Lengte70 mm Vierkante paal 090307PSTOHO
4
8
Een a voerWaterbak
101007PSTPOL19
A
9
6
7
7
8
5
2
2
2
1
6
9
7
7
7

A-A ( 1:15 )
D ( 1:15 )
Benaming
Title
Opmerking
Comment
Datum
Date
Tekening
Drawing
MOD PST 013 259
Polyester waterbak
H=900
16-5-2022
Samenstelling module Assembly module
C
A
A
D D
150
760
760
956
900
6
700

0
BOER PLAY
A ssembly manual for Hand pump HPOl
T his manual has been written to guide you in the assembly of the Mh2o hand pump
type HP0l, suitable for sucking water from a borehole or water storage. Manuals for
other Mh2o products can be found at www.mh2opompen.nl
Preparation:
In this installation manual we assume that
the location of the pump is already fully
e q uipped to be able to install the pump.
In brief:
• T he supplied base plate and associated
threaded rods have already been poured
level in a concrete foundation, or you have
made all preparations for another proper
fastening.
• T he threaded ends are shortened to 25mm
for the outermost and 16mm for the middle
above the base plate.
• A borehole is provided at depth with
sufficient supply or a water storage, of which the casing / supply is in the middle of the
base plate and of which the diameter does not e x ceed 110mm. T his should be
shortened along with the base plate.
• S ufficient drainage options are provided for e x cess pumped-up or spilled water.
R e q uired tools:
• T wo spanners 17mm
• A llen key 8mm, 2.5mm and 1.5mm
• L arge slotted screwdriver
•Pipe wrench
•Drill with a 3mm drill bit
• A clinker or paving stone
• A piece of rope of at least 2 meters,
connect the sisal strings of the
packaging for this. Make a loop on one
side and tie a piece of cardboard from
the wrapping on the other side as a
bobbin.
R emarks:
• Installation of the HP01 hand pump re q uires two people.
• T he heaviest part of the pump, the chassis weighs 14kg.
Ass e mb l y m an u al f o r Hand pump HP O l1
of 4

0
BOER PLAY
I nstallation:
1. P
ull the piston rod out of the gra y c y linder
and pull the tie rod out of the blue riser on
the male side. C onnect the tie rod of the first
riser to the piston rod of the pump c y linder
and tighten securel y using the two open-end
wrenches. Slide the protection hose out of
the riser pipe as far as possible over the
piston rod.
2. C onnect the pump c y linder to the riser b y
twisting the blue tube into the c y linder.
B e careful not to damage the thread, feel
gentl y until the thread catches. Then tighten
the tube firml y , hand tight is sufficient.
3. Lower the c y linder and riser combination
into the well / water storage. The black
c y linder is the first to enter the well! Let the
pump pipe protrude appro x imatel y 1 meter
above the borehole and hold or clamp it.
4. Depending on the depth of the source /
water storage, one or more risers are now
attached to each other to reach the depth.
U se the string for this. P ull this through the
empt y riser, make sure that the loop
protrudes from the side with e x ternal thread.
P lace the pipe with string ne x t to the
borehole / water storage. W hile one holds the
riser tightl y , the other connects the ne x t tie
rod to the one sticking out of the blue pipe.
Slide the protective hose over the connecting
nut as far as possible and gentl y lower the
drawbar into the riser. Secure the loop of the
string to the connecting nut. Slide the riser
with string over the pump rod and screw it
onto the riser protruding from the borehole.
Let it all sink into the well. U
se the string to
pull the drawbar back out of the riser and
repeat the above until the desired depth is
reached.
Ass e mb l y m an u al f o r Hand pump HP O l2 o
f 4

5. When the desired depth has been reached,
clamp the riser to appro x imatel y 1.5 meters
above the borehole / water storage. Now drill a
hole in the riser about 1.2 meters below the
end of the tube. This ensures that the pump
drains automaticall y and can therefore never
freeze. Pull the drawbar out of the riser and
secure the protective hose with the adjusting
ring.
6. Turn the rod head onto the threaded rod.
A ttach the loop of the string to the rod end.
R oute the other end of the string from below
through the wire sock of the chassis.
7. Take the chassis and put it over the riser,
guiding the string through the wire sock in the
chassis. F irml y screw the riser onto the wire
sock. Using the string, pull the sucker rod and
rod end out of the wire sock.
8. Lower the chassis over the studs. F irml y fi x
the chassis to the base plate b y turning a cap
nut on both sides on the center stud. Now take
the black plastic cap and push it into the
chassis so that the level points to the outlet.
Guide the sucker rod through the hole. Place a
clinker or paving stone on its side on the base
plate.
9. Prepare the housing b y mounting the
operating handle and removing the blind plug
with a screwdriver.
10. R emove the string from the drawbar and,
using a pipe wrench, grasp it firml y just above
the spout. Grab the housing and slide it over
the chassis until it rests on the stone. Y ou still
have the pull rod with the pipe wrench.
Ass e mb l y m an u al f o r Hand pump HPOl
0
BOER PLAY
3 o f 4

11. N ow connect the tie rod to the operating
handle b y tightening the A llen screw through
the hole in the housing. F irst, make sure the
hole, handle and rod end are aligned. T o do
this, move the lever and with the pipe wrench
the rod end until the y are in front of the hole.
N ow put the bolt on the A llen ke y and insert it
through the hole in the handle and rod end,
tighten securel y .
12. R emove the stone from between the base
plates and lower the housing over the studs.
S ecure the housing b y turning the cap nuts on
the remaining four threaded ends. F inall y ,
screw the blind plug back into the hole in the
housing.
13. T he assembl y of the pump is now
complete. M ake sure ever y thing is working
properl y . Check that the pump has not been
damaged during installation. Check the pump
for burrs and sharp edges that could injure
users. Visit www.mh2opompen.nl for
information about use and maintenance
Ass e mb l y m an u al f o r Hand pump HPOl
0
BOER PLAY
4 o f 4