BOERPLAY PSTE105.015 User manual

Balance bridge
PSTE105.015
Powered by TCPDF (www.tcpdf.org) 1 / 1

© Copyright BOERplay 27-1-2022 Revision: A PST 105 015
main dimensions
Hoofdafmetingen
Hauptabmessungen
Dimensiones principales
Dimensions principales
NL
DE
ES
FR
0,00 m
0,36 m
0,52 m
0,88 m
1,78 m
2,07 m
2,17 m
2,93 m
0,00 m 0,31 m 3,89 m 4,39 m
0,00 m
0,81 m
1,01 m
1,76 m

© Copyright BOERplay 27-1-2022 Revision: A PST 105 015
obstacle free zone
Obstakelvrije zone
Hindernissfreie raum
Zona libre de obstáculos
Zone libre d’obstacles
NL
DE
ES
FR
7,87 m
5,09 m
R1,75m
R1,75m
R1,75m

© Copyright BOERplay 27-1-2022 Revision: A PST 105 015
ground plan
Bodemplan
Bodenplan
Plan de superficie
Plan de surface
NL
DE
ES
FR
Grondmarkering
Ground level marker
0,67 m
0,64 m
2,11 m 3,58 m 2,19 m
2,48 m0,50 m2,13 m
0,30 m
0,81 m
1,56 m
3,05 m

Opmerking
BenamingRev.Bew.
Volgnr.
Progr.Type
#
Nr.
Adventure PlayAanbouw touw recht
A
002022PSTMOD
11
tbv PST.105.015Losse Palen
A
015105PSTMOD
1
2
© Copyright BOERplay 27-1-2022 Revision: A PST 105 015
order of assembly
Montagevolgorde
Montagereihenfolge
Orden de esemblado
Ordre de montage
NL
DE
ES
FR
1
2
Typeplaatje
Identification plate
B
Geleverde delen:
A - Staander
B - Hercules touw
C - Paal lengte 2500
D - Paal lengte 4000
E - Paal lengte 1 00
Bevestiging sets:
1 - RVS M12 bevestigingssets voor alle palen
Montagevolgorde:
1 - Graaf de gaten volgens het bodemplan en plaats A op de juiste diepte en met de
juiste hoogte
2 - Plaats C en bevestig D aan A en C
- Bevestig E aan C en D
4 - Bevestig B aan C met 2
5 - Controleer of het toestel voldoet aan de afmetingen zoals op blad 'afmetingen'
6 - Dicht de gaten en verdicht het zand
Controles:
1 - Correcte opbouw en alle bevestigingsmiddelen
2 - Controleer de afmetingen van de valbodem t.o.v. het toestel
- Controleer of er zich bij de staanders geen halsbeknellingen kunnen voordoen
Supplied parts:
A - Support
B - Hercules rope
C - Post length 2500
D - Post length 4000
E - Post length 1 00
Mounting kits:
1 - Stainless steel M12 fasteners for the posts
2 - Stainless steel security screws, M6
Assembly sequence:
1 - Dig the holes according to the ground plan and place A conform to the dimensions
2 - Place C and connect D to A and C
- Connect E to C and D
4 - Connect B to C with 2
5 - Check that the equipment conforms to the dimensions shown on sheet 'dimensions'
6 - Close the holes and compact the sand
Checks:
1 - Correct assembly and all the fasteners
2 - Check the dimensions of the safety area compared to the play equipment
- Check that no neck entrapment can be caused by the supports

LOGBOOK
Type indication Adventure Play
Article number PSTE105.015
Product Name Balance bridge
Maximum fall height 0,9 m
Construction year 2023
Certificate 032695
Inspection body TUV Nederland QA BV
Ekkersrijt 4401
5692 DL Son
Manufacturer name Boer Speeltoestellen
Hyacintstraat 2 - 4255 HX Nieuwendijk
Phone: [phone]
Fax: [phone]
Installer name _______________________________________________________
_______________________________________________________
_______________________________________________________
Playground location _______________________________________________________
Information about the owner of the playground
Name: _______________________________________________________
Address: _______________________________________________________
Zipcode and city: _______________________________________________________
Contact: _______________________________________________________
Phone number: _______________________________________________________
Information about the manager of the playground
Name: _______________________________________________________
Address: _______________________________________________________
Zipcode and city: _______________________________________________________
Contact: _______________________________________________________
Phone number: _______________________________________________________
Powered by TCPDF (www.tcpdf.org)

LOGBOOK
Inspection and maintenance
Date of
inspection
maintenance
Time of
inspection
maintenance
Name
executor of
inspection
Name
executor of
maintenance
Found defects Parts to be
replaced
Accidents
Date
accident
Age of
victim Probable cause of injury Occurred injury Measures taken after accident

Inspection and maintenance intervals
Nr Inspection Maintenance
months
between
inspections
1
Verify equipment's stability, junctions and
missing parts Inspect bolts, screws and nuts for
absence, jams, corrosion and wear
Add missing parts, secure joints, apply
missing fixing agent and replace
corroded parts
1
2
Check suspension for wear Replace worn parts and/or remove non-
functioning parts
1
3
Inspect rotating parts such as hinges, rolling-
element bearings, etc for wear and acceptability
Replace worn parts and/or remove non-
functioning parts
1
4
Check wood for splinters, unacceptable damage
and signs of rot, especially at ground level
Repair damage Replace affected wood
Smoothen splintered wood and sharp
edges
1
5
Inspect foundation for stability, tearing and
coverage
Restore foundation and covering
material
3
6
Examine rubber and synthetic parts for wear,
damage and breakage Replace for OEM original parts
3
7
Examine fibre reinforced plastic parts, especially
slides, for wear
Replace for OEM parts if the fibres are
visible
6
8
Inspect metal for corrosion and damage in the
coating
Restore any damaged coating (after
removing rust and applying primer)
6
9
Check ropes, cables, chains and nets for wear
and damage Steel cables and nets which are
tensioned must be checked for tension
Replace parts where necessary Steel
cables and nets must be tensioned
3
10
Inspect equipment for unsafe changes and
additions
Remove unsafe additions and correct
unsafe changes
1
11
Inspect safety surfaces Restore and repair where necessary
1
Remarks
1 If used intensively, all points require extra attention
2 Extreme weather conditions and locations may require a higher inspection frequency Discuss this with the
supplier
3 Vandalism-sensitive locations require stricter inspections, possibly daily
4 Re-tighten all connections in Robinia equipment two months after first use
5 Re-span spatial networks two months after first use
6 Check the terrain regularly for items that do not belong there, are unsafe or may be used wrongly Examples
are poisonous plants, glass shards, etc Frequency depends on strain

7 Remember that bad maintenance leads to unsafe conditions and notably faster impoverishment of the
playground area
8 Replacement parts can be ordered at the manufacturer with the OEM part numbers on the module drawing
Drawings can be found in the user guide
9 The impact area shall be provided with impact attenuating surface according to the specified falling height
•Up to 0,6m height of fall: no requirements regarding impact attenuation
•Turf, topsoil: suitable up to 1000mm height of fall
•Loose fill (sand, gravel, bark, woodchips): up to 3000mm height of fall Layer thickness is height
of fall / 10 +100mm, with a minimum of 300mm
•Synthetic surfaces (Rubber tiles, artificial turf, wetpour, tigermulch etc ): height of fall and layer
thickness according to the information of the supplier
10 This list is conform the CEN-standard "playground equipment and surfacing NEN-EN 1176-7"
Improving the
foundations
(for equipment without concrete in the standard
foundation)
If the impact area is loose fill (sand, gravel, bark,
woodchip, etc ), or if the soil itself does not add to
stability of the equipment (i e sand, pumice, peat soil)
pour 50l of concrete per post
For instance:
Square: 0,6 x 0,6 x 0,16m
Round: ø0,35 x 0,5m
Round: ø0,50 x 0,2m

A ( 1 : 8 )
Benaming
Title
Opmerking
Comment
Datum
Date
Tekening
Drawing
MOD PST 022 002 A
Aanbouw touw recht
Adventure Play
31-3-2020
Samenstelling module Assembly module
Opmerking
BenamingRev.Bew.
Volgnr.
Progr.Type#Nr.
M12, L= 260, RVS A2- 0Draadeind+borgm.+ringen+dop 260M12SET
BMR
2
1
5 x 0 - RVS A2- 0
Schroef Assy
0 0005002BSR122
M12BORGMOER 012012010BSR33
M12 - RVS A2- 0
Sluitring
003012030BSR34
5 MM RVS
D-sluiting
000005031BSR35
Dop zwart
Beschermdop M10-M12 060010DOPKST36
KUNSTSTOFRING 008005RNGKST3
Lengte =2100
Paal 14-16
021160PSTOHO18
Lengte =2500
Paal 14-16
025160PSTOHO19
Lengte =3600
Paal 14-16
036160PSTOHO110
Lengte = 1500
Standaard plank 120x20
150211PSTOHO
111
Lengte = 2600
Standaard plank 120x20
260211PSTOHO212
M12x150Slotbout met lip 150088PSTSME313
3,8m
Touw
380006PSTSNT
114
1,6m
Touw
160006PSTSNT115
A
0,00m
1,45m
3,60m
2,69m
2,60m
1,49 m
3,55 m
10
8
9
12
0,61 m
Grondmarkering
Ground level marker
14
6
1
2
15 5 13
7
43

Opmerking
BenamingRev.Bew.
Volgnr.
Progr.Type#Nr.
M12, L= 300, RVS A2-70
Draadeind+borgm.+ringen+dop
300M12SETMR31
M12ORGMOER 012012010SR12
M12 - RVS A2-70
Sluitring
003012030SR13
5 MM RVSD-sluiting 000005031SR
14
Dop zwart
eschermdop M10-M12
060010DOPKST
15
KUNSTSTOFRING 008005RNGKST16
Lengte =1300
Paal 14-16
013160PSTOHO17
Lengte =4000
Paal 14-16
040160PSTOHO18
Lengte =2500
Paal 14-16
025160PSTOHO
1
9
M12x150
Slotbout met lip
150088PSTSME
1
10
© Copyright BOERplay 27-1-2022 Revision: A MOD PST 105 015
assembly manual - module
Montagehandleiding - module
Montageanleitung - Modul
Manual de ensamblado - módulo
Manuel de montage - module
NL
DE
ES
FR
9
8
7
0,97 m 0,13 m
2,39 m
3,88 m
0,85 m
0,53 m
1,49 m
1
4235610
Powered by TCPDF (www.tcpdf.org)