bolid S2000-AR2 User manual

1
ADDRESSABLE DOUBLE-INPUT MODULE
S2000-AR2 Rev.02
OPERATIONS MANUAL
1. DESCRIPTION AND OPERATION
1.1 Product Designation
1.1.1 S2000-AR2 Rev.02 Addressable Double-Input Module (hereinafter referred to as the module) is
used with a polling loop controller such as S2000-KDL, S2000-KDL-2I, S2000-KDL-2I Rev.01, S2000-
KDL-S in Orion integrated security systems. The module is designed to connect non-addressable dry
contact detectors into the polling loop of a polling loop controller as well as to supervise fire protection
systems (voice announcement systems, smoke control systems, fire protection dampers, etc.) and other
control and auxiliary systems with dry contact outputs. The module is powered and communicates data
over the polling loop of the polling loop controller. The module supports the polling loop protocol
DPLS_v2.xx providing getting polling loop voltage values at the point where it is connected and features a
tamper switch.
1.1.2 The module is designed for round-the-clock operation.
1.1.3 The module is a reparable and regularly maintained product.
1.1.4 The design of the module doesn’t provide its operation in aggressive and dusty environments and in
ex-hazardous premises.
1.2 Specifications
Table 1.2.1
№Parameter Value
1.2.1 Power supply voltage (PL voltage), V - 8 through 11
1.2.2 Average consumed current, mA - 1.0 max
1.2.3 Power input - 1
1.2.4 Start-up time, s - 15 max
1.2.5 Monitored circuits (device loops) - 2
1.2.6 Ingress Protection Rating as per GOST 14254-2015 - IP41
1.2.7 Immunity to mechanical exposure as per OST 25 1099-83 - Arrangement Category III
1.2.8
Vibration exposure:
- Frequency range, Hz
- Max acceleration
- 1-35;
- 0.5g
1.2.9 Climatic version as per OST 25 1099-83 - О3
1.2.10 Operating temperatures, °С- Minus 30 to +55
1.2.11 Relative humidity, % - Up to 93 at +40°С
1.2.12 Weight, kg - 0.04 max
1.2.13 Overall dimensions, mm - 56 ×38 ×20
1.2.14 Non-stop operation - 24/7
1.2.15 MTBF in quiescent mode, hours - 80000
1.2.16 Survival probability - 0.98758
1.2.17 Average service life, years - 10
1.2.18 The module passes the standards of industrial radio disturbance prescribed for Class B equipment
as per GOST 30805.22.

2
1.2.19 In terms of immunity to industrial radio disturbance, the module meets the requirements of Test
Severity Level III as per GOST R 50009.
1.2.20 The module withstands radio-frequency electromagnetic field in 80 through 100 MHz range as per
GOST 30804.4.3.
1.2.21 The module withstands electrostatic discharge of Test Severity Level III as per GOST 30804.4.2.
1.3 Standard Delivery
Table 1.3.1 represents the content of S2000-AR2 Rev.02 standard delivery.
Table 1.3.1
Item Quantity, pc(s).
S2000-AR2 Rev.02 Addressable Double-Input Module 10
S2000-AR2 Rev.02 Operations Manual 1
Resistor MF 1/4W-10k-5% 20
Woodscrew 1-3x25.016 GOST 1144-80 20
Wall Plug 6x30 20
Individual packing 10
Group packing 1
2INTENDED USAGE
Detailed information on operational restrictions, design, mounting, wiring, setting, and operability /
performance test procedures is contained in S2000-AR2 Rev.02 User’s Manual, which can be found online
at bolid.ru in the PRODUCTS section on the page of S2000-AR2 Rev.02.
3MAINTENANCE
3.1 The module shall be maintained by personnel with Safety Qualification Level II of higher.
3.2 The module shall be maintained according to a scheduled-preventive system which provides annual
service.
3.3 Maintenance works are described in S2000-AR2 Rev.02 User’s Manual, which can be found online at
bolid.ru in the PRODUCTS section on the page of S2000-AR2 Rev.02.
4ROUTINE REPAIR
4.1 Routine repair of defective equipment is to be performed by the manufacturer or in authorized repair
centers. The product shall be sent for repair in line with established procedures.
4.2 An equipment failure resulted from consumer’s not observing rules of mounting and operation is not a
reason for claims and warranty repair.
4.3 Claims shall be submitted to the following address:
NVP Bolid, #4 Pionerskaya Str., Korolyov, Moscow Region, 141070, Russia
Tel./fax: [phone] (PBX), E-mail: [e-mail].
4.4 In case of any issue related to use of the product, please contact the technical support:
[phone] or e-mail: [email protected].
ATTENTION
The equipment shall be submitted for repair being assembled and clean and along with all
the parts listed in the documentation.
Claims are accepted only if a reclamation report describing the failure is applied to the
submitted equipment.

3
5STORAGE
5.1 In a transport container the equipment can be stored at ambient temperatures -50°Сthrough +50°С
and relative humidity up to 95% at +35°С.
5.2 In the consumer package the equipment can be stored only in heated premises at temperatures +5°С
through +40°Сand relative humidity up to 80% at +20°С.
6TRANSPORTING
6.1 The equipment can be transported in a transport container at ambient temperatures -50°Сto +50°C
and relative humidity up to 95% at +35°С.
7DISPOSAL
7.1 The equipment is disposed of considering that it contains no toxic components.
7.2 The content of precious materials: does not require accountability for storage, retirement and disposal
(Clause 1.2 of GOST 2.608-78).
7.3 The content of non-ferrous metals: does not require accountability for retirement and further disposal.
8MANUFACTURER WARRANTY
8.1 The manufacturer guaranties this product meets with technical requirements specified in the manuals
if the user follows the instructions for transportation, storage, installation, and usage.
8.2 The warranty period is 18 months since the day of putting the product into operation but no more than
24 months from the manufacturer’s date of production.
9CERTIFICATION INFORMATION
To get information about module certificates please refer to S2000-AR2 Rev.02 User’s Manual, which can
be found online at bolid.ru in the PRODUCTS section on the page of S2000-AR2 Rev.02 on the
Download tab.
10 ACCEPTANCE AND PACKAGING CERTIFICATE
S2000-AR2 Rev.02 Addressable Double-Input Modules (serial numbers can be seen on their
enclosures) are manufactured, accepted in line with requirements of national standards and applicable
technical documentation, approved as ready for use, and packaged by the Bolid Company.
Responsible for acceptance and packaging
QCD ________________________________ ________________________
Name Date/Month/Year