Bond Vast Industrial Grand Resort D71 M11772 User manual

1

2
SAFETY INFORMATION
Please read and understand this entire manual before attempting to assemble, operate or
install the product. If any parts is missing or damaged, do not attempt to assemble the product.
Two to four people are needed for assembly.
Load of the hook on the roof: 50 lbs. (max)
In order to avoid damage to the shelter and its components, use appropriate tools.
Check all screws on a regular basis to maintain the solidity of the structure.
Keep instructions and parts list for further use.
Estimated Assembly Time: Approx. 5 hours
Tools required for Assembly (not included): Ladder, 5 ft. (at least 5 ft. during assembly).
WARNING
KEEP ALL FLAME AND HEAT SOURCES AWAY FROM TENT FABRIC.
This tent meets the flammability requirements of CPAI-84. The fabric may burn if left in
continuous contact with any flame source. The application of any foreign substance to the
tent fabric may render the flame-resistant properties ineffective.
CAUTION
Do not leave outside during high winds, heavy rains or snow.
The mosquito nets must be removed for winter storage.
Do not attach gazebo to wood or concrete deck or patio.
WARRANTY
1 year limited warranty.
Limited warranty applicable on parts only. Warranty extends solely to the original purchaser, who
must offer the original sales receipt for record.
EXCLUDED
Damages due to vandalism, abuse and wrong use of the product is not covered by the warranty.
Damages due to extreme weather conditions such as thunderstorm and windstorm.
MAINTENANCE
If this shelter needs repairs, DO NOT RETURN THE PRODUCT TO SEARS.
In case of a defective part of if a problem occurs while using this Product, please contact Bond Vast
at 1-800-961-9838, 9AM ~ 5PM, Pacific Time Zone, Monday - Friday.
Or email us: [email protected].

AD
XY
AC ZAQ AB
AO
AV
W
AL AI T
AP
AN
AR
V
AW
AV
AG
AT
AF
AM
AJ AI
AL U
AG
AV
AH
AK
AJ
AM
AE AF
AS
J
AT
L
K
F
G
N
A
C
O
B
B
P
H
I
C
E
FF
AX
B
D
M
3
U

4
Parts list
Item Description IllustrationQty
1
1
1
1
1
3
2
6
6
2
2
4
6
4
4
Post 1
Post 2
Post 3
Base flange
Base cap
Long crossbar 1
Long crossbar 2
Short crossbar 1
Short crossbar 2
Short crossbar 3
Short crossbar 4
Center connector
Tip connector
Long supporter
Short supporter
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O

5
Item Description IllustrationQty
2
12
3
4
1
6
4
4
4
1
2
2
4
1
2
P
Q
R
S
T
U
V
W
X
Y
Z
AB
AC
AD
AE
Connector tube
Plastic cap
Connect wire 1
Connect wire 2
Roof connector 1
Roof connector 2
Roof cap
Short roof tube
Corner connector
Long roof tube
Air vent tube
Air vent panel 1
Air vent panel 2
2-tier corner connector
Roof tube 1

6
DescriptionItem Qty Illustration
4
4
4
4
4
4
4
4
4
4
4
4
2
2
2
Roof tube 2
Roof tube 3
Roof tube 4
Roof tube 5
Roof tube 6
Roof tube 7
Roof tube 8
Roof tube 9
Roof panel 1
Roof panel 2
Roof panel 3
Roof panel 4
Roof panel 5
Eave tube 1
Eave tube 2
AF
AG
AH
AI
AJ
AK
AL
AM
AN
AO
AP
AQ
AR
AS
AT

DescriptionItem Qty Illustration
4
4
1
1
6
Eave tube 3
Center protector
Corner protector
Mosquito net
AC adapter
AU
AV
AW
AX
AY
74
34
20
20
34
24
1
1
Qty IllustrationDescriptionItem
Screw 4
Screw 1
Screw 2
Screw 3
Bolt nut
Stake
Hex wrench
Spanner
AA
BB
CC
DD
EE
FF
GG
HH
7
Hardware kit

8
A
B
C
1
3
2
6
6
D
E
B
E
D
E
B
AA AA
D
1
1
1. Slide base cap (E) into post 2 (B), then fit base flange (D) undernearth post 2 (B). Insert screw 1 (AA)
through post 2 (B) and secure the base flange (D). Slide down base cap (E) into place as shown.
Repeat the step for all rest posts (A, B, C).

9
F
G
M
2
2
4
FMMG
F
M
F
AA
G
AA
AA
1
2
1. Insert long crossbar 1 (F) into long crossbar 2 (G) and secure with screw 1 (AA). Then secure
tip connector (M) onto the long crossbar 1 (F) and long crossbar 2 (G) by using screw 1 (AA) as
figure shown.
Repeat this step for remaining long crossbar 1 (F) and long crossbar 2 (G).
2
2
2
1

H
I
M
L
1
1
1
1
HL
M
I
H
L
M
I
AA AA
AA
1
1
1. Insert short crossbar 1 (H) into short crossbar 2 (I), then secure center connector (L) and
tip connector (M) onto short crossbar set (H, I) by using screw 1 (AA) as the figure shown.
10

J
K
M
L
1
1
1
1
J
M
LK
1
AA AA
AA
J
LK
M
1
1. Insert short crossbar 3 (J) into short crossbar 4 (K), then secure center connector (L) and
tip connector (M) onto the short crossbar set (J, K) by using screw 1 (AA) as the figure shown.
11

L1
G
LF
1
1
2
AC
B
AA
L
F
CC
C
CC
G
G
1
2
1. Secure long crossbar set (G, F) on the post 1 (A) and post 2 (B) by using screw 3 (CC), then
secure the long crossbar set (G, F) on post 3 (C) by using screw 3 (CC) as figure shown.
2. Then secure center connector (L) onto the long crossbar set (G, F) by using screw 1 (AA) as shown.
12
You need 3 persons for this step.

L1
BC
B
G
LF
B
G
G
CC
B
CC
L
F
AA
1
1
2
12
1. Secure long crossbar set (G, F) on the post 2 (B) by using screw 3 (CC), then secure
the long crossbar set (G, F) on post 3 (C) by using screw 3 (CC) as figure shown.
2. Then secure center connector (L) onto the long crossbar set (G, F) by using screw 1 (AA) as shown.
You need 3 persons for this step.
13

CC
H
1
B
BC
B
A
CB
J
K
11
1
1
IH
You need 3 persons for this step.
1. Secure the short crossbar set (H, I) on the post 2 (B) by using screw 3 (CC) as shown.
2. Secure the short crossbar set (J, K) on the post 1 (A) and post 2 (B) by using screw 3 (CC)
as shown.
14

15
N Q
4 8
GDD N
B
Q
NDD
G
F
B
B
C
N
A
CB
N
F
G
NN
1
2
1
2
1. Secure long supporter (N) onto long crossbar (F) by using screw 4 (DD) as figure shown.
Then secure both end section of long supporter (N) between corner post (B) and center post (C)
by using screw 4 (DD), and cover it with plastic cap (Q) as figure shown.
Repeat this step for remaining 3 long supporters (N).

O
P
Q
4
2
4
J
B
O
OP
DD Q
DD
IJ
K
B
A
C
B
C
B
O
OPH
1
2
12
1. Insert short supporter (O) into connector tube (P), then insert screw 4 (DD) through connector tube (P)
and short supporter (O) into the short crossbar 2 (I), then secure the end section of short supporter (O)
onto post 2 (B) by using screw 4 (DD) and cover the plastic cap (Q).
Repeat the step for remaining short supporter (O) and connector tube (P).
16

17
R3
HI
GJ
KF
BR
FGJ
K
H
B
A
C
A
R
GF
I
C
B
B
1. Insert connector wire 1 (R) between long crossbar 2 (G) and post 1 (A), then insert connector wire 1 (R)
between long crossbar 1 (F) between post 2 (B) as figure shown.
2. Insert connector wire 1 (R) between short crossbar 1 (H) and short crossbar 2 (I) as shown.
3
12
1
3
2

18
S4
G
S
B
FG
S
FGJK
I
C
H
BA
H
C
F
G
BB
C
1
2
1
2
2
1
1. Insert connect wire 2 (S) between long crossbar 1 (F), long crossbar 2 (G) and post 3 (C) as shown.
2. Insert connect wire 2 (S) between long crossbar 2 (G), short crossbar 1 (H) and post 2 (B) as shown.
Repeat for remaining 2 connect wire 2 (S).

19
T
U
X 1
X 6
U
BB
1
T
EE
TU
U
M
1
2
U
M
AA
2
U
1. Insert 2pcs screw 2 (BB) into short roof tube (U), insert 1 of screw 2 (BB) though roof connector (T)
and secure with bolt nut (EE) as figure 1 shown.
Then secure the end section of short roof tube (U) with tip connector (T) by using screw 1 (AA) as
figure 2 shown.
Repeat for the remaining short roof tube (U).
U
U

20
V
W
4
4
W
V
1
1
W
VAA
1. Secure corner connector (V) onto long roof tube (W) by using screw 1 (AA).
Repeat for all remaining corner connector (V) and long roof tube (W).