Bosch HMB406 User manual

i _ _ _A{{
8uiJt°in Microwave Oven
_ns_allationInstruclons
Fal Mode/s_ HMIB402_HMB405 HMB406
W _Trim K Is: tHMT472 HMT4?5 HMT476.HMZ402

Please read this entire manual before proceeding
RMPORTANT:
iNSTALLER:
OWN ER:
Local codes vary. Rnstallation, electrical connections, circuit breakers
and grounding must comply with aii applicable codes. Save these instruc
tions for your local electrical inspector's use.
Please leave these Installation Instructions with this unit for the
owner.
Please retain these instructions for future reference,
Disconnect power at the breaker before installing.
Step 1:
Step 2:
Step S:
Step 4:
Step 5:
Unpacking ............................................ 3
Cabinet Preparation ........................... 4
Electncai hstatiaqon .......................... 5
nnstalling the Microwave Oven _. 5- 7
nnstalling the Microwave Trim ........... 7

Step 1: Unpacking
A. Microwave Oven Model HMB
Open the box and carefully remove all fillers and packing material
Your new Bosch microwave includes the following:
, Care & Use manual (1)
o Quick Guide (1)
, Warranty Card (1)
, Turn Table (1)
, Turn Table Support (1)
lB. Trim Kit Models HMT
Open the box and carefully remove all fillers and packing materials.
Parts list:
" Trim Frame (1)
, Bottom Duct (1)
, Antitip Bracket (1)
" Side Duct (1)
" Upper Duct (1)
"installation instructions (1)
Bottom Bracket (1)
, Screws #6xl/2" (1 3)
, Screws #8x1" (6)
, Template (1)
Table 1
30" cabinet
27" cabinet
Trim Kits
HMT406 (Black)
H MT402 (White)
H MT405 (Stainless)
HMT476 (Black)
H MT472 (White)
H MT475 (Stainless)
Microwave Ovens
HMB406 (Black)
HMB402 (White)
HMB405 (Stainless)
HMB406 (Black)
HMB402 (White)
HMB405 (Stainless)
Caution:
Trim kits are designed for use only with the Bosch microwave oven models listed (See Table 1).
For safety, do not alter or modify any part of this kit or oven.

Step 2: Cabinet Preparation
• The cabinet cutout dimensions are shown in Fig-
ure 1,
When the microwave oven is installed at the end
of a cabinet run, adjacent to a perpendicular wail
or cabinet door, it is a good practice to allow at
bast 1/4" space between the side of the trim and
wail or door,
Trim Kits Dimensions
Width (B) HMT40x 28-1/2"
HMT47x 25-1/2"
Height (A) All Trim Kits 16-s!4"
Depth (C) All Trim Kits 22-s!4" o24"
• Your microwave oven can be installed into a cabb
net or wail by itself or above any of the following
Bosch wall ovens: HBL43, HBN/L44 or HBN/L74,
• Outlet can be located anywhere within the shaded
area as indicated in Figure 1,
jJ
A
J
I
Figure 1
Top of
microwave
shelf
Bosch
single wail
oven
Figure 2
3" minimum

Step 3: Electrical installation
The Bosch microwave oven is equipped with a grounded cord. The wall receptacle must be installed
and grounded in accordance with the national electrical code. Also, electrical connections and
grounding must comply with all applicable local codes.
The electrical requirements for a separate circuit serving only this microwave oven are: 120V, 60Hz,
15Amp.
Step 4: Installing the Microwave Oven
Step A Front
1/2" Screws (2)
1/2" Screws (2)
2_
3_
Disconnect the microwave oven from the outlet
before proceeding with installation.
Remove any loose items (turntable, support, etc.)
from the microwave oven.
Fasten the bottom bracket to the bottom duct
by using two 1/2" screws.
4. Install bottom duct with four 1/2" screws to
bottom of microwave.
FRONT VIEW OF
.... _i tVI[CROWAVE
1/2" Screws (2)

Step 4: installing The Microwave Oven (continued)
Step B
1, Remove the one existing screw from the Heftside of the microwave oven,
2, Connect the side duct to upper duct as shown,
a) hsert projecting tabs of upper duct into holies of side duct,
b) Bend tabs up as shown,
NOTE: Remove any oi[ or dirt on surface of microwave oven before ducts are attached,
a) Upper Duct b)
3 ta bs_
! 3 holies
I
Side Duct
,Pee[ off the backing of douMe-sided tape, Attach
the side duct and upper duct assemMy on the mi-
crowave cabinet, Press down firmHy on ducts, Fas-
ten duct assemMy to Heftside of cabinet with one
existing screw,
Step C
1, On the cutout floor, mark hole centers for the
anti-tip brackets as shown using the supplied
template, Be sure to align the center line of tem-
plate to center line of cutout floor,
2, Drill two holes for anti-tip bracket, (Use 7/64" drill
or #35 drill)
3, hstaH anti-tip bracket onto cutout floor using two
1/2" screws,
DIMENSIONS:
A = 4-1/4''
B=3"
C = 18-3/16 ''
ICenterline
Cutout Floor
IF
71J2,,Screwst2/I
I
I I
nti-tip Bracket
t_

Step 4: installing the Microwave Oven (continued}
Step D
1. Slide microwave oven part way into cabinet
opening. (Bottom bracket must be flat to the
cutout floor to engage correctly with anti-tip
brackets as shown).
2, Plug in the microwave oven,
3, Center the microwave oven within the cutout
opening and siide the microwave oven in the
anti-tip bracket, (Ensure the microwave oven is
accurateiy centered,
4, Drill[ piiot hobs (use 7/64" drill[ or #35 drii[)
through the positioning flange and then install[
three 1/2" screws at the front of the bottom duct
as shown.
Step 5: installing the Trim Kit
Bracket Bottom
Bracket
,("Z ,_.'"
1/2" screws flange
Cutout
opening
1. Place the trim kit frame over the microwave oven,
,
,
4,
,
,
important Note: Trim kit frame orientation is
important, Orient the frame
so the louvers are sloping
downward to the front, (gee
Figure Detail A).
Make sure the trim kit is level and centered with
respect to microwave oven, Mark four hob cen-
ters through the four mounting hobs of the trim
kit,
NOTE: Center the trim kit frame equally on aii
four sides,
Remove the trim kit and drill four pilot hobs, (use
7/64 drill or #35 drill)
Attach the trim kit frame by using four 1" screws,
Make sure that the orientation is correct as
stated above,
Your trim kit is now fully installed° Replace
an}i loose items that have been removed from
inside microwave oven,
Please keep this installation instruction for future
reference,
WWA_W
" Screw[ i
I
' o
Pilot
hob
J
Trim Kit
Cutout
Opening
hob
Figure Detail of "A"

Bosch reserves the right to change specifications or design without notice, Some models are certified for use in
Canada, Bosch is not responsJble for products which are transported from the United States for use in Canada,
Check with your local Canadian distributor or dealer, Bosch, 5551 McFadden Avenue, Huntington Beach, CA 92649,
For the most up-to-date critical installation dimensions by fax, use your fax handset and phone [phone]OO,
Use code#8030,
BOSCH
BSH Home Appliances Corp.
Bosch Customer Support Call Center, 5551 McFadden Avenue, Huntington Beach_ CA 92649 ° [phone]
9000002507 Rev,A •_._u2003 BSH Home Appliances Corp,, Litho U,S,A, 12/03
8