Bosch HB 56 N Series User manual

Register your
new device on
MyBosch now and
get free benefits:
bosch-home.com/
welcome
Oven
HB..56...N
[en] User manual and installation instructions

en Safety
2
Table of contents
USER MANUAL
1 Safety ....................................................................2
2 Preventing material damage ...............................4
3 Environmental protection and saving en-
ergy .......................................................................5
4 Familiarising yourself with your appliance ........6
5 Accessories..........................................................8
6 Before using for the first time ...........................10
7 Basic operation ..................................................10
8 Rapid heating .....................................................11
9 Time-setting options..........................................11
10 Programme.........................................................12
11 Childproof lock...................................................14
12 Basic settings.....................................................15
13 Cleaning and servicing......................................15
14 EcoClean ...........................................................17
15 Cleaning assistance...........................................18
16 Shelf supports....................................................19
17 Appliance door...................................................21
18 Troubleshooting.................................................24
19 Disposal..............................................................25
20 Customer Service...............................................26
21 How it works.......................................................26
22 INSTALLATION INSTRUCTIONS .......................29
22.1 General installation instructions.......................30
1 Safety
Observe the following safety instructions.
1.1 General information
¡Read this instruction manual carefully.
¡Keep the instruction manual and the
product information safe for future refer-
ence or for the next owner.
¡Do not connect the appliance if it has been
damaged in transit.
1.2 Intended use
This appliance is designed only to be built
into kitchen units. Read the special installation
instructions.
Only a licensed professional may connect ap-
pliances without plugs. Damage caused by in-
correct connection is not covered under the
warranty.
Only use this appliance:
¡To prepare meals and drinks.
¡In private households and in enclosed
spaces in a domestic environment.
¡Up to an altitude of max. 4000m above
sea level.
1.3 Restriction on user group
This appliance may be used by children aged
8 or over and by people who have reduced
physical, sensory or mental abilities or inad-
equate experience and/or knowledge,
provided that they are supervised or have
been instructed on how to use the appliance
safely and have understood the resulting
dangers.
Children must not play with the appliance.
Children must not perform cleaning or user
maintenance unless they are at least 15 years
old and are being supervised.
Keep children under the age of 8 years away
from the appliance and power cable.
1.4 Safe use
Always place accessories in the cooking com-
partment the right way round.
→"Accessories", Page8
WARNING‒Risk of fire!
Combustible objects that are left in the cook-
ing compartment may catch fire.
▶Never store combustible objects in the
cooking compartment.
▶If smoke is emitted, the appliance must be
switched off or the plug must be pulled out
and the door must be held closed in order
to stifle any flames.
Loose food remnants, fat and meat juices
may catch fire.
▶Before using the appliance, remove the
worst of the food residues and remnants
from the cooking compartment, heating ele-
ments and accessories.
Opening the appliance door creates a
draught. Greaseproof paper may come into

Safety en
3
contact with the heating element and catch
fire.
▶Never place greaseproof paper loosely
over accessories when preheating the ap-
pliance and while cooking.
▶Always cut greaseproof paper to size and
use a plate or baking tin to hold it down.
WARNING‒Risk of burns!
The appliance and its parts that can be
touched become hot during use.
▶Caution should be exercised here in order
to avoid touching heating elements.
▶Young children under 8 years of age must
be kept away from the appliance.
Accessories and cookware get very hot.
▶Always use oven gloves to remove ac-
cessories or cookware from the cooking
compartment.
When the cooking compartment is hot, any al-
coholic vapours inside may catch fire.
▶Only use small quantities of drinks with a
high alcohol content in food.
▶Open the appliance door carefully.
WARNING‒Risk of scalding!
The accessible parts of the appliance become
hot during operation.
▶Never touch these hot parts.
▶Keep children at a safe distance.
Hot steam may escape when you open the
appliance door. Steam may not be visible, de-
pending on the temperature.
▶Open the appliance door carefully.
▶Keep children at a safe distance.
If there is water in the cooking compartment
when it is hot, this may create hot steam.
▶Never pour water into the cooking compart-
ment when the cooking compartment is
hot.
WARNING‒Risk of injury!
Scratched glass in the appliance door may
develop into a crack.
▶Do not use any harsh or abrasive cleaners
or sharp metal scrapers to clean the glass
on the oven door, as they may scratch the
surface.
The hinges on the appliance door move when
the door is opened and closed, which could
trap your fingers.
▶Keep your hands away from the hinges.
Components inside the appliance door may
have sharp edges.
▶Wear protective gloves.
WARNING‒Risk of electric shock!
Incorrect repairs are dangerous.
▶Repairs to the appliance should only be
carried out by trained specialist staff.
▶Only use genuine spare parts when repair-
ing the appliance.
▶If the power cord of this appliance is dam-
aged, it must be replaced by trained spe-
cialist staff.
If the insulation of the power cord is dam-
aged, this is dangerous.
▶Never let the power cord come into contact
with hot appliance parts or heat sources.
▶Never let the power cord come into contact
with sharp points or edges.
▶Never kink, crush or modify the power
cord.
An ingress of moisture can cause an electric
shock.
▶Do not use steam- or high-pressure clean-
ers to clean the appliance.
If the appliance or the power cord is dam-
aged, this is dangerous.
▶Never operate a damaged appliance.
▶Never operate an appliance with a cracked
or fractured surface.
▶Never pull on the power cord to unplug the
appliance. Always unplug the appliance at
the mains.
▶If the appliance or the power cord is dam-
aged, immediately unplug the power cord
or switch off the fuse in the fuse box.
▶Call customer services. →Page26
WARNING‒Danger: Magnetism!
Permanent magnets are used in the control
panel or in the controls. These may affect
electronic implants, e.g. heart pacemakers or
insulin pumps.
▶Wearers of electronic implants must stay at
least 10 cm away from the control panel.
WARNING‒Risk of suffocation!
Children may put packaging material over
their heads or wrap themselves up in it and
suffocate.
▶Keep packaging material away from chil-
dren.
▶Do not let children play with packaging ma-
terial.

en Preventing material damage
4
Children may breathe in or swallow small
parts, causing them to suffocate.
▶Keep small parts away from children.
▶Do not let children play with small parts.
1.5 Halogen bulb
WARNING‒Risk of burns!
The bulbs in the cooking compartment get
very hot. There is still a risk of burning for
some time after they have been switched off.
▶Do not touch the glass cover.
▶Avoid contact with your skin when cleaning.
WARNING‒Risk of electric shock!
When changing the bulb, the bulb socket con-
tacts are live.
▶Before replacing the bulb, ensure that the
appliance is switched off in order to pre-
vent a potential electric shock.
▶Also unplug the appliance from the mains
or switch off the circuit breaker in the fuse
box.
1.6 Cleaning function
WARNING‒Risk of burns!
The outside of the appliance gets very hot
when the cleaning function is in progress.
▶Never touch the appliance door.
▶Allow the appliance to cool down.
▶Keep children at a safe distance.
2 Preventing material damage
2.1 General
ATTENTION!
Objects on the cooking compartment floor at over
50°C will cause heat to build up. The baking and
roasting times will no longer be correct and the enamel
will be damaged.
▶Do not place any accessories, greaseproof paper or
foil of any kind on the cooking compartment floor.
▶Only place cookware on the cooking compartment
floor if a temperature above 50°C has been set.
When the cooking compartment is hot, any water in-
side it will create steam. The change in temperature
may cause damage.
▶Never pour water into the cooking compartment
when it is still hot.
▶Never place cookware containing water on the
cooking compartment floor.
The prolonged presence of moisture in the cooking
compartment leads to corrosion.
▶Allow the cooking compartment to dry after use.
▶Do not keep moist food in the cooking compartment
for a long time with the door closed.
▶Do not store food in the cooking compartment.
Leaving the appliance to cool down with the door open
will damage the front of neighbouring kitchen units over
time.
▶Always allow the cooking compartment to cool
down with the door closed after cooking at high
temperatures.
▶Take care not to trap anything in the appliance
door.
▶Only leave the cooking compartment to dry with the
door open if a lot of moisture was produced during
operation.
Fruit juice dripping from the baking tray leaves stains
that cannot be removed.
▶When baking very juicy fruit flans, do not pack too
much on the baking tray.
▶If possible, use the deeper universal pan.
Using oven cleaner in a hot cooking compartment
damages the enamel.
▶Never use oven cleaner in the cooking compartment
when it is still warm.
▶Remove all food remnants from the cooking com-
partment and the appliance door before you next
heat up the appliance.
If the seal is very dirty, the appliance door will no
longer close properly during operation. This may dam-
age the front of adjacent kitchen units.
▶Keep the seal clean at all times.
▶Never operate the appliance if the seal is damaged
or missing.
Sitting or placing objects on the appliance door may
damage it.
▶Do not place or hang objects on the appliance door.
▶Do not place cookware or accessories on the appli-
ance door.
With certain models, accessories may scratch the door
pane when closing the appliance door.
▶Always push accessories fully into the cooking com-
partment.

Environmental protection and saving energy en
5
3 Environmental protection and saving energy
3.1 Disposing of packaging
The packaging materials are environmentally compat-
ible and can be recycled.
▶Sort the individual components by type and dispose
of them separately.
3.2 Saving energy
If you follow these instructions, your appliance will use
less power.
Only preheat the appliance if the recipe or the recom-
mended settings tell you to do so.
¡Not preheating the appliance can reduce the en-
ergy used by up to 20%.
Use dark-coloured, black-coated or enamelled baking
tins.
¡These types of baking tin absorb the heat particu-
larly well.
Open the appliance door as little as possible during
operation.
¡This will maintain the temperature in the cooking
compartment and eliminate the need for the appli-
ance to reheat.
When baking multiple dishes, do so in succession or
in parallel.
¡The cooking compartment is heated after baking
the first dish. This reduces the baking time for the
second cake.
If the cooking time is relatively long, you can switch
the appliance off 10minutes before the cooking time
ends.
¡There will be enough residual heat to finish cooking
the dish.
Remove any accessories that are not being used from
the cooking compartment.
¡Accessories that are not being used do not need to
be heated.
Allow frozen food to defrost before cooking.
¡This will save the energy that would otherwise be
required to defrost it.

en Familiarising yourself with your appliance
6
4 Familiarising yourself with your appliance
4.1 Controls
You can use the control panel to configure all functions
of your appliance and to obtain information about the
operating status.
Note:On certain models, specific details such as col-
our and shape may differ from those pictured.
1
2 3
1
Buttons and display
The buttons are touch-sensitive surfaces. To se-
lect a function, simply press lightly on the relev-
ant field.
The display shows symbols for active functions
and the time-setting options.
→"Buttons and display", Page6
2
Function selector
Use the function selector to set the types of
heating and other functions.
You can turn the function selector clockwise or
anti-clockwise from the zero setting .
Depending on the appliance, the function se-
lector can be pushed in. Press on the function
selector to click it into or out of the zero set-
ting .
→"Types of heating and functions", Page6
3
Temperature selector
Use the temperature selector to set the temper-
ature for the type of heating and select settings
for other functions.
You can only turn the temperature selector
clockwise from the zero setting until it offers
resistance. You cannot turn it any further than
this.
Depending on the appliance, the temperature
selector can be pushed in. Press on the tem-
perature selector to click it into or out of the
zero setting .
→"Temperature and setting levels", Page7
4.2 Buttons and display
You can use the buttons to set various functions for your appliance. The display shows the settings.
If a function is active, the corresponding symbol lights up in the display. The clock symbol only lights up when you
change the time.
Symbol Function Use
Time-setting options Select the time , timer , cooking time and the end time ⁠.
To select the individual time-setting options, press the button sev-
eral times.
The red bar above or below the respective symbol indicates the
function to which the setting in the display corresponds.
Minus
Plus
Decrease the setting values.
Increase the setting values.
Weight Select a weight for the programmes.
Childproof lock Activate or deactivate the childproof lock.
4.3 Types of heating and functions
To ensure that you always use the right type of heating to cook your food, we have explained the differences and ap-
plications below.
Symbol Type of heating What it's used for/how it works
3Dhot air Bake and roast on one or more levels.
The fan distributes the heat from the ring-shaped heating element in the back
wall evenly around the cooking compartment.

Familiarising yourself with your appliance en
7
Symbol Type of heating What it's used for/how it works
Gentle hot air Cook selected dishes gently on one level without preheating.
The fan distributes the heat from the ring-shaped heating element in the back
wall evenly around the cooking compartment. The food is cooked in phases us-
ing residual heat.
Select a temperature of between 120°C and 230°C.
Always keep the appliance door closed when cooking.
This type of heating is used to determine the energy consumption in air recircu-
lation mode and the energy efficiency class.
Pizza setting Cook pizza or dishes that require a lot of heat from below.
The bottom heating element and the ring-shaped heating element in the back
wall heat the cooking compartment.
Bottom heating Final baking or cooking food in a bain marie.
Heat is emitted from below.
Full-surface grill Grill flat items such as steak and sausages, or make toast. Gratinate food.
The entire area underneath the grill element becomes hot.
Hot air grilling Roast poultry, whole fish and larger pieces of meat.
The grill element and the fan switch on and off alternately. The fan circulates the
hot air around the food.
Top/bottom heating Traditionally bake or roast on one level. This type of heating is ideal for cakes
with moist toppings.
The heat is emitted evenly from above and below.
This type of heating is used to measure the energy consumption in the conven-
tional mode.
Other functions
Here, you can find an overview of other functions of your appliance.
Symbol Function Use
Rapid heating Rapidly preheat the cooking compartment without accessories.
→"Rapid heating", Page11
Oven light Illuminate the cooking compartment without heating.
→"Lighting", Page8
Programme Use programmed setting values for various types of food.
→"Programme", Page12
EcoClean Set the cleaning function, which regenerates the self-cleaning surfaces in the
cooking compartment.
→"EcoClean ", Page17
4.4 Temperature and setting levels
There are different settings for the types of heating and functions.
Note:For temperature settings above 250°C, the appliance reduces the temperature to approx. 240°C after ap-
prox. 10minutes. If your appliance has the top/bottom heating or bottom heating types, this temperature reduction
does not take place.
Symbol Function Use
Zero setting The appliance is not heating up.
50–275 Temperature range Set the temperature in the cooking compartment in°C.
1, 2, 3
or
I, II, III
Grill settings Set the grill settings for Full-surface grill and Grill, small area (depending on
the appliance model).
1 = low
2 = medium
3 = high
Programme Set the programme function.
EcoClean Set the cleaning function.

en Accessories
8
Heat-up indicator
The appliance indicates when it is heating up.
The line at the bottom of the display turns red in three
increments, from left to right, as the cooking compart-
ment heats up. When the appliance is in operation, one
of the red sections of the line goes out during the heat-
ing phases.
When you are preheating the appliance, the optimal
time to place your food in the cooking compartment is
as soon as all three sections of the line have turned
red.
Note:Due to thermal inertia, the temperature displayed
may differ slightly from the actual temperature inside
the cooking compartment.
4.5 Cooking compartment
The functions in the cooking compartment make your
appliance easier to use.
Shelf supports
The shelf supports in the cooking compartment enable
you to place accessories at different heights.
→"Accessories", Page8
Your appliance has five shelf positions. The shelf posi-
tions are numbered from bottom to top.
Depending on the appliance, the shelf supports are fit-
ted with pull-out rails or clip-on pull-out rails. The pull-
out rails are fixed in place and cannot be removed. The
clip-on pull-out rails allow you to use them as you wish
at all free shelf positions.
You can remove the shelf supports, e. g. for cleaning.
→"Shelf supports", Page19
Self-cleaning surfaces
The self-cleaning surfaces in the cooking compartment
are coated with a porous, matt ceramic layer and have
a rough surface. When the appliance is in operation,
the self-cleaning surfaces absorb splashes from roast-
ing or grilling and break them down.
The following surfaces are self-cleaning:
¡Back wall
¡Ceiling
¡Side walls
Use the cleaning function regularly to help retain the
cleaning ability of the self-cleaning surfaces and pre-
vent damage.
→"EcoClean ", Page17
Lighting
The oven light lights up the cooking compartment.
With most types of heating and functions, the lighting
lights up during operation. When the function selector
is turned to bring operation to an end, the lighting goes
out.
The Oven light setting on the function selector can be
used to switch on the light without heating.
Cooling fan
The cooling fan switches on and off depending on the
appliance's temperature. The hot air escapes above
the door.
ATTENTION!
Do not cover the ventilation slot above the appliance
door. The appliance overheats.
▶Ensure that the ventilation slots are unobstructed.
To ensure that the appliance cools down more quickly
after operation, the cooling fan continues to run for a
certain period afterwards.
Appliance door
If you open the appliance door during operation, the
operation continues.
5 Accessories
Use original accessories. These have been made espe-
cially for your appliance.
Note:Accessories may become deformed if they get
hot. Deformation has no effect on function. As the ac-
cessory cools down, it will regain its original shape.
The accessories supplied may differ depending on the
appliance model.

Accessories en
9
Accessories Use
Wire rack ¡Cake tins
¡Ovenproof dishes
¡Cookware
¡Meat, e.g. roasting joints or steak
¡Frozen meals
Universal pan ¡Moist cakes
¡Baked items
¡Bread
¡Large roasts
¡Frozen meals
¡Catching dripping liquids, e.g. fat when
grilling food on the wire rack.
Baking tray ¡Tray bakes
¡Small baked items
5.1 Locking function
The locking function prevents the accessories from tilt-
ing when they are pulled out.
You can pull out the accessories approximately halfway
without them tipping. The accessories must be inserted
into the cooking compartment correctly for the tilt pro-
tection to work properly.
5.2 Sliding accessories into the cooking
compartment
Always slide accessories into the cooking compartment
correctly. This is the only way to ensure that accessor-
ies can be pulled out approximately halfway without tip-
ping.
1. Turn the accessories so that the notch is at the
rear and is facing downwards.
2. Insert accessories between the two guide rods for
the shelf position.
Wire rack Insert the wire rack with the open
side facing the appliance door and
the curved lip facing downwards.
Baking tray
E.g. univer-
sal pan or
baking tray
Slide the tray, e.g. the universal pan,
in with the sloping edge facing the
appliance door.
3. Place the accessory at the shelf positions with the
pull-out rails and pull out the pull-out rails.
Wire rack
or baking
tray
Position the accessory so that its
edge is behind the lug on the pull-
out rail.
Note:The pull-out rails lock in place when they are
fully pulled out. Gently push the pull-out rails back
into the cooking compartment.
4. Push the accessory all the way in, making sure that
it does not touch the appliance door.
Note:Take any accessories that you will not be using
out of the cooking compartment while the appliance is
in operation.
Combining accessories
You can combine the wire rack with the universal pan
to catch any liquid that drips down.
1. Place the wire rack on the universal pan so that
both spacers are on the rear edge of the univer-
sal pan.
2. Insert the universal pan between the two guide rods
for a shelf position. In so doing, the wire rack is on
top of the upper guide rod.
Wire rack
on univer-
sal pan

en Before using for the first time
10
5.3 Other accessories
You can purchase other accessories from our after-
sales service, specialist retailers or online.
You will find a comprehensive range of products for
your appliance in our brochures and online:
www.bosch-home.com
Accessories vary from one appliance to another. When
purchasing accessories, always quote the exact
product number (E no.) of your appliance.
You can find out which accessories are available for
your appliance in our online shop or from our after-
sales service.
6 Before using for the first time
Configure the settings for initial start-up. Clean the ap-
pliance and accessories.
6.1 Initial use
You need to make settings for initial use before you
can use your appliance.
Setting the time on the clock
Once the appliance has been connected to the mains
or following a power failure, the time flashes on the dis-
play. The time starts at "12:00". Set the current time.
Requirement:The function selector must be set to the
"Off" position ⁠.
1. Use the or button to set the time.
2. Press the button.
aThe time that is set appears on the display.
Tip:You can go to the basic settings →Page15 to
specify whether or not the time should be shown on
the display.
6.2 Cleaning the appliance before using it
for the first time
Clean the cooking compartment and accessories be-
fore using the appliance to prepare food for the first
time.
1. Remove any accessories and leftover packaging,
such as polystyrene pellets, from the cooking com-
partment.
2. Before heating the appliance, wipe the smooth sur-
faces in the cooking compartment with a soft, damp
cloth.
3. Keep the room ventilated while the appliance is
heating.
4. Set the type of heating and temperature.
→"Basic operation", Page10
Type of heat-
ing
3Dhot air
Temperature Maximum
Cooking time 1 hour
5. Switch off the appliance after the specified cooking
time.
6. Wait until the cooking compartment has cooled
down.
7. Clean the smooth surfaces with soapy water and a
dish cloth.
8. Clean the accessories using soapy water and a dish
cloth or soft brush.
7 Basic operation
7.1 Switching on the appliance
▶Turn the function selector to any position other than
the "Off" position ⁠.
aThe appliance is switched on.
7.2 Switching off the appliance
▶Turn the function selector to the "Off" position ⁠.
aThe appliance is switched off.
7.3 Setting the type of heating and
temperature
1. Use the function selector to set the type of heating.
2. Use the temperature selector to set the temperature
or grill setting.
aThe appliance starts heating after a few seconds.
3. When your food is ready, switch off the appliance.
Tips
¡The most suitable type of heating for your food can
be found in the description of the type of heating.
→"Types of heating and functions", Page6
¡You can also set a cooking time and end time on
the appliance.
→"Time-setting options", Page11
Changing the type of heating
You can change the type of heating at any time.
▶Use the function selector to set the required type of
heating.
Changing the temperature
You can change the temperature at any time.
▶Use the temperature selector to set the required
temperature.

Rapid heating en
11
8 Rapid heating
To save time, you can use rapid heating to shorten the
preheat time.
Only use rapid heat-up when a temperature of over
100°C has been set.
After rapid heating, it is best to use the following types
of heating:
¡3Dhot air
¡Top/bottom heating
8.1 Setting rapid heating
To ensure an even cooking result, do not place the
food in the cooking compartment until rapid heating
has come to an end.
1. Use the function selector to select rapid heating ⁠.
2. Use the temperature selector to set the required
temperature.
aRapid heating starts after a few seconds.
aWhen the rapid heating process ends, an audible
signal sounds and the heating indicator goes out.
3. Use the function selector to set a suitable type of
heating.
4. Place the food in the cooking compartment.
9 Time-setting options
Your appliance has different time-setting options, with
which you can control its operation.
9.1 Overview of the time-setting options
With the button, select the different time-setting op-
tions.
Time-setting
option
Use
Timer The timer can be set independently
of the appliance when it is in opera-
tion. It does not affect the appliance.
Cooking time If you set a cooking time, operation
of the appliance stops automatically
once this time has elapsed.
End time For the cooking time, you can set the
time at which operation ends. The
appliance starts up automatically so
that it finishes cooking at the re-
quired time.
Time You can set the time.
9.2 Setting the timer
The timer runs independently of the appliance when it
is in operation. The timer can be set when the appli-
ance is switched on or off, up to 23 hours and 59
minutes. The timer has its own audible signal so that
you can tell whether it is the timer or a cooking time
which has elapsed.
1. Press the button repeatedly until is highlighted
in the display.
2. Use the or button to set the timer duration.
Button Default value
5minutes
10 minutes
The timer duration can be set in 30-second incre-
ments up to 10 minutes. Above 10 minutes, the
time increments become longer the higher the
value.
aThe timer starts and the timer duration begins to
count down after a few seconds.
aAn audible signal sounds and the timer duration is
zero in the display when the timer duration has
elapsed.
3. Once the timer duration has elapsed:
‒Press any button to switch off the timer.
Changing the timer
You can change the timer duration at any time.
Requirement: is highlighted on the display.
▶Use the or button to change the timer duration.
aThe appliance applies the change after a few
seconds.
Cancelling the timer
You can cancel the timer duration at any time.
Requirement: is highlighted on the display.
▶Use the button to reset the timer duration to zero.
aAfter a few seconds, the appliance applies the
change and goes out.
9.3 Setting the cooking time
You can set a cooking time for operation of up to 23
hours 59 minutes.
Requirement:The type of heating and temperature or
setting are set.
1. Press the button repeatedly until is highlighted
in the display.
2. Use the or button to set the cooking time.
Button Default value
10 minutes
30minutes
The cooking time can be set in 1-minute increments
up to 1 hour, and then in 5-minute increments.
aThe appliance starts heating and the cooking time
counts down after a few seconds.
aIf the cooking time has elapsed, an audible signal
sounds and the display shows the cooking time as
zero.

en Programme
12
3. When the cooking time has elapsed:
‒Press any button to end the audible signal before
it sounds.
‒To set a cooking time again, press the button.
‒When your food is ready, switch off the appli-
ance.
Changing the cooking time
You can change the cooking time at any time.
Requirement: is highlighted on the display.
▶Change the cooking time using the or button.
aThe appliance applies the change after a few
seconds.
Cancelling the cooking time
You can cancel the cooking time at any time.
Requirement: is highlighted on the display.
▶Reset the cooking time to zero using the button.
aAfter a few seconds, the appliance applies the
change and continues to heat without a cooking
time.
9.4 Setting the end time
You can delay the time at which cooking is due to fin-
ish by up to 23 hours and 59 minutes.
Notes
¡The end time cannot be set for types of heating with
grill function.
¡In order to achieve a good cooking result, do not
delay the end time once the appliance is already in
operation.
¡Food will spoil if you leave it in the cooking com-
partment too long.
Requirements
¡The type of heating and temperature or setting are
set.
¡A cooking time is set.
1. Press the button repeatedly until is highlighted
in the display.
2. Press the or button.
aThe display shows the calculated end time.
3. Use the or button to delay the end time.
aAfter a few seconds, the appliance applies the set-
ting and the display shows the set end time.
aOnce the calculated start time has been reached,
the appliance starts heating up and the cooking
time starts counting down.
aOnce the time has elapsed, an audible signal
sounds and the display shows the cooking time as
zero.
4. When the cooking time has elapsed:
‒Press any button to end the signal prematurely.
‒To set another cooking time, press the button.
‒When your food is ready, switch off the appli-
ance.
Changing the end time
In order to achieve a good cooking result, you can only
change the set end time before operation starts and
the cooking time starts counting down.
Requirement: is highlighted on the display.
▶Use the or button to delay the end time.
aThe appliance applies the change after a few
seconds.
Cancelling the end time
You can delete the set end at any time.
Requirement: is highlighted on the display.
▶Reset the end time to the current time plus the set
cooking time using the button.
aAfter a few seconds, the appliance applies the
change and starts heating up. The cooking time
counts down.
9.5 Setting the time on the clock
Once the appliance has been connected to the mains
or following a power failure, the time flashes on the dis-
play. The time starts at "12:00". Set the current time.
Requirement:The function selector must be set to the
"Off" position ⁠.
1. Use the or button to set the time.
2. Press the button.
aThe time that is set appears on the display.
Tip:You can go to the basic settings →Page15 to
specify whether or not the time should be shown on
the display.
Changing the time on the clock
You can change the time on the clock at any time.
Requirement:The function selector must be set to the
"Off" position ⁠.
1. Press the button repeatedly until is highlighted
in the display.
2. Use the or button to change the time.
aThe appliance applies the change after a few
seconds.
10 Programme
The programmes help you to use your appliance to
prepare different dishes by selecting the optimum set-
tings automatically.
10.1 Cookware for programmes
You should therefore use heat-resistant cookware that
is suitable for temperatures up to 300°C.
Glass or glass ceramic cookware is best. The joint
should cover approx. two thirds of the cookware base.
Cookware made from the following material is not
suitable:
¡Bright, shiny aluminium
¡Unglazed clay
¡Plastic or plastic handles

Programme en
13
10.2 Programme table
The programme numbers are assigned to specific foods.
The weight can be set to between 0.5kg and 2.5kg.
No. Food Cookware Weight setting Add liquid Shelf
posi-
tion
Information
01 Chicken, unstuffed
Ready to cook,
seasoned
Roasting dish with
glass lid
Chicken weight No 2 Place in the cook-
ware with the breast
facing up
02 Turkey breast
Whole, seasoned
Roasting dish with
glass lid
Turkey breast
weight
Cover the
bottom of the
roasting dish,
and add up
to 250g ve-
getables if re-
quired
2 Do not sear the meat
beforehand
03 Vegetable stew
Vegetarian
Deep roasting dish
with lid
Total weight As per recipe 2 Cut vegetables that
take longer to cook
(e.g. carrots) into
smaller pieces than
vegetables that take
less time to cook
(e.g. tomatoes)
04 Goulash
Diced beef or pork,
with vegetables
Deep roasting dish
with lid
Total weight As per recipe 2 Place the meat at the
bottom and cover
with vegetables
Do not sear the meat
beforehand
05 Meat loaf, fresh
Minced beef, pork or
lamb
Roasting dish with
lid
Weight of the joint No 2 -
06 Pot-roasted beef
E.g. prime rib,
shoulder, rump or mar-
inated beef roast
Roasting dish with
lid
Weight of meat Almost cover
the meat with
liquid
2 Do not sear the meat
beforehand
07 Beef roulades
Stuffed with vegetables
or meat
Roasting dish with
lid
Total weight of all
of the stuffed roul-
ades
Add stock,
water or an-
other liquid
to the dish
until the beef
olives are al-
most covered
2 Do not sear the meat
beforehand
08 Leg of lamb, well-
done
Boned, seasoned
Roasting dish with
lid
Weight of meat Cover the
bottom of the
roasting dish,
and add up
to 250g ve-
getables if re-
quired
2 Do not sear the meat
beforehand

en Childproof lock
14
No. Food Cookware Weight setting Add liquid Shelf
posi-
tion
Information
09 Joint of veal, lean
E.g. tenderloin or eye
Roasting dish with
lid
Weight of meat Cover the
bottom of the
roasting dish,
and add up
to 250g ve-
getables if re-
quired
2 Do not sear the meat
beforehand
10 Pork neck joint
Boned, seasoned
Roasting dish with
glass lid
Weight of meat Cover the
bottom of the
roasting dish,
and add up
to 250g ve-
getables if re-
quired
2 Do not sear the meat
beforehand
10.3 Preparing food for the programme
Use fresh and, ideally, chilled food.
1. Weigh the food.
The weight of the food is required in order to cor-
rectly set the programme.
2. Add the food to the cookware.
3. Place the cookware onto the wire rack.
Always place the cookware into the cooking com-
partment while it is cold.
10.4 Setting a programme
The appliance selects the optimal type of heating, tem-
perature and cooking time. All you need to do is set
the weight.
Notes
¡You can set the weight only in the intended area.
¡After the programme starts, you can no longer
change the programme and the weight.
1. Use the function selector to set Programme ⁠.
2. Use the temperature selector to set Programme ⁠.
3. Use the or button to set the required pro-
gramme.
4. Press the button.
5. Use the or button to set the weight of your
food. Always set the next higher weight.
‒The display shows the calculated cooking time.
The cooking time cannot be changed.
‒For some programmes, the button can be
used to delay the end.
→"Setting the end time", Page12
‒To change the programme, press the button.
aAfter a few seconds, the programme starts and the
cooking time counts down.
aIf the programme has ended, an audible signal
sounds and the display shows the cooking time as
zero.
6. When the programme ends:
‒Press any button to end the audible signal pre-
maturely.
‒To set a cooking time for further cooking, press
the button. The appliance continues to heat
using the programme settings.
‒When your food is ready, switch off the appli-
ance.
11 Childproof lock
You can secure your appliance to prevent children
from accidentally switching it on or changing the set-
tings.
Notes
¡You can go to the basic settings →Page15 to
specify whether you want the option to set the child-
proof lock.
¡After a power cut, the childproof lock is deactivated.
11.1 Activating and deactivating the
childproof lock
Requirement:The function selector must be set to the
"Off" position ⁠.
▶To activate the childproof lock, press and hold the
button until appears in the display.
‒To deactivate the childproof lock, press and hold
the button until goes out in the display.

Basic settings en
15
12 Basic settings
You can configure the appliance to meet your needs.
12.1 Overview of the basic settings
Here you can find an overview of the basic settings and factory settings. The basic settings depend on the features
of your appliance.
Display Basic setting Selection
Time display = hide the time
= display the time1
Signal duration upon completion of a cook-
ing time or timer period
= 10 seconds
= 30 seconds1
= 2 minutes
⁠ ⁠ Button tone when pressing a button = off
= on1
Cooling fan run-on time = short
= medium
= long1
= extra long
Waiting time until a setting is applied = 3 seconds1
= 6 seconds
= 10 seconds
⁠ ⁠ Childproof lock can be adjusted = no
= yes1
Water hardness2 = softened
= soft (up to 1.5mmol/l)
= medium (1.5–2.5mmol/l)
= hard (2.5–3.8mmol/l)
= very hard (above 3.8mmol/l)1
1Factory setting (may vary according to model)
2Only for appliance types with steam function
12.2 Changing basic settings
Requirement:The appliance is switched off.
1. Press and hold the button for approximately
fourseconds.
aThe first basic setting appears in the display,
e.g. ⁠ ⁠ ⁠.
2. Use the or button to change the setting.
3. Use the button to switch to the next basic setting.
4. To save the changes, press and hold the button
for approx. fourseconds.
Note:Following a power failure, the factory basic set-
tings are restored.
12.3 Discarding changes to the basic
settings
▶Turn the function selector.
aAll changes are discarded and not saved.
13 Cleaning and servicing
To keep your appliance working efficiently for a long
time, it is important to clean and maintain it carefully.
13.1 Cleaning products
In order to avoid damaging the various oven surfaces
on the appliance, do not use unsuitable cleaning
products.
WARNING‒Risk of electric shock!
An ingress of moisture can cause an electric shock.
▶Do not use steam- or high-pressure cleaners to
clean the appliance.
ATTENTION!
Unsuitable cleaning products may damage the sur-
faces of the appliance.
▶Do not use harsh or abrasive cleaning products.
▶Do not use cleaning products with a high alcohol
content.
▶Do not use hard scouring pads or cleaning
sponges.
▶Do not use any special cleaners for cleaning the ap-
pliance while it is hot.

en Cleaning and servicing
16
Using oven cleaner in a hot cooking compartment
damages the enamel.
▶Never use oven cleaner in the cooking compartment
when it is still warm.
▶Remove all food remnants from the cooking com-
partment and the appliance door before you next
heat up the appliance.
New sponge cloths contain residues from production.
▶Wash new sponge cloths thoroughly before use.
Suitable cleaning agents
Only use cleaning products that are suitable for the dif-
ferent surfaces on your appliance.
Follow the instructions on cleaning the appliance.
→"Cleaning the appliance", Page17
Appliance front
Surface Suitable cleaning agents Information
Stainless steel ¡Hot soapy water
¡Special stainless steel
cleaning products
suitable for hot sur-
faces
To prevent corrosion, remove any patches of limescale, grease,
starch or albumin (e.g. egg white) on stainless steel surfaces imme-
diately.
Apply a thin layer of the stainless steel cleaning product with a soft
cloth.
Plastic or painted
surfaces
E.g. control panel
¡Hot soapy water Do not use glass cleaner or a glass scraper.
Appliance door
Area Suitable cleaning agents Information
Door panels ¡Hot soapy water Do not use a glass scraper or a stainless steel wool.
Tip:Remove the door panels in order to clean them thoroughly.
→"Appliance door", Page21
Door cover ¡Made of stainless
steel:
Stainless steel cleaner
¡Made of plastic:
Hot soapy water
Do not use glass cleaner or a glass scraper.
Tip:Remove the door cover for thorough cleaning.
→"Appliance door", Page21
Door handle ¡Hot soapy water To avoid permanent stains, remove descaling agents from the door
handle immediately.
Door seal ¡Hot soapy water Do not remove or scrub.
Cooking compartment
Area Suitable cleaning agents Information
Enamel surfaces ¡Hot soapy water
¡Vinegar water
¡Oven cleaner
Soak any heavily soiled areas and use a brush or steel wool.
Leave the appliance door open to dry the cooking compartment
after cleaning it.
Notes
¡Enamel burns at very high temperatures, causing minor discol-
ouration. The functionality of your appliance is not affected by
this.
¡The edges of thin trays cannot be completely enamelled and may
be rough. This does not impair corrosion protection.
¡Food residues will leave a white coating on the enamel surfaces.
The coating does not pose a health risk. The functionality of your
appliance is not affected by this. You can remove residues with
lemon juice.
Self-cleaning sur-
faces
- Follow the instructions for self-cleaning surfaces.
→"Cleaning self-cleaning surfaces in the cooking compartment",
Page17
Glass cover for
the oven light
¡Hot soapy water Use oven cleaner to remove very heavy soiling.

EcoClean en
17
Area Suitable cleaning agents Information
Rails ¡Hot soapy water Soak any heavily soiled areas and use a brush or steel wool.
Tip:Remove the shelf supports for cleaning.
→"Shelf supports", Page19
Pull-out system ¡Hot soapy water Use a brush to remove very heavy soiling.
Clean the pull-out rails while they are pushed in so that you do not
remove the lubricant.
Do not clean in the dishwasher.
Tip:Detach the pull-out system for cleaning.
→"Shelf supports", Page19
AccessorIes ¡Hot soapy water
¡Oven cleaner
Soak any heavily soiled areas and use a brush or steel wool.
Enamelled accessories are dishwasher-safe.
13.2 Cleaning the appliance
In order to avoid damaging the appliance, you must
clean your appliance only as specified, and with suit-
able cleaning products.
WARNING‒Risk of burns!
The appliance and its parts that can be touched be-
come hot during use.
▶Caution should be exercised here in order to avoid
touching heating elements.
▶Young children under 8 years of age must be kept
away from the appliance.
WARNING‒Risk of fire!
Loose food remnants, fat and meat juices may catch
fire.
▶Before using the appliance, remove the worst of the
food residues and remnants from the cooking com-
partment, heating elements and accessories.
Requirement:Read the information on cleaning
products.
→"Cleaning products", Page15
1. Clean the appliance using hot soapy water and a
dish cloth.
‒For some surfaces, you can use alternative
cleaning agents.
→"Suitable cleaning agents", Page16
2. Dry with a soft cloth.
13.3 Cleaning self-cleaning surfaces in the
cooking compartment
The back wall, ceiling and side walls of the cooking
compartment are self-cleaning and have a rough sur-
face.
ATTENTION!
If you do not clean the self-cleaning surfaces regularly,
they may become damaged.
▶If dark stains are visible on the self-cleaning sur-
faces, use the cleaning function to clean the cook-
ing compartment.
▶If a prompt to clean appears in the display, use the
cleaning function to clean the cooking compart-
ment.
▶Do not use oven cleaner or abrasive cleaning aids.
If oven cleaner accidentally comes into contact with
the self-cleaning surfaces, dab it off immediately us-
ing water and a sponge cloth. Do not rub.
▶Use the cleaning function.
→"EcoClean ", Page17
14 EcoClean
Clean the cooking compartment regularly using the
cleaning function EcoClean to help retain the cleaning
ability of the self-cleaning surfaces and prevent dam-
age.
The self-cleaning surfaces in the cooking compartment
are coated with a porous, matt ceramic layer and have
a rough surface. When the appliance is in operation,
the self-cleaning surfaces absorb splashes from roast-
ing or grilling and break them down.
The following surfaces are self-cleaning:
¡Back wall
¡Ceiling
¡Side walls
ATTENTION!
If you do not clean the self-cleaning surfaces regularly,
they may become damaged.
▶If dark stains are visible on the self-cleaning sur-
faces, use the cleaning function to clean the cook-
ing compartment.
▶If a prompt to clean appears in the display, use the
cleaning function to clean the cooking compart-
ment.
▶Do not use oven cleaner or abrasive cleaning aids.
If oven cleaner accidentally comes into contact with
the self-cleaning surfaces, dab it off immediately us-
ing water and a sponge cloth. Do not rub.
14.1 Cleaning recommendation
The appliance detects the type and duration of the ap-
pliance operation and, if necessary, recommends using
the cleaning function.
▶If lights up in the display when the appliance is
switched off, use the cleaning function as soon as
possible.

en Cleaning assistance
18
‒To remove the information from the display,
press any button except for the button. How-
ever, the information will continue to be dis-
played until the cleaning function has been run in
full.
‒To reset the cleaning recommendation, press
and hold the button for approx. fourseconds.
The information does not reappear until the appli-
ance has been used again a certain number of
times.
Notes
¡If the appliance is already dirty, e.g. because you
have used it to cook fatty poultry or roasts, or if you
notice dark patches on the self-cleaning surfaces,
do not wait until this information appears in the dis-
play to run the cleaning function. The more often
you use the cleaning function, the longer the self-
cleaning surfaces will retain their cleaning ability.
¡After a power failure, the cleaning recommendation
is reset. It is therefore a good idea to run the clean-
ing function after a power failure has occurred.
14.2 Preparing the appliance for the
cleaning function
In order to achieve a good cleaning result, prepare the
appliance carefully.
ATTENTION!
Using oven cleaner on the self-cleaning surfaces dam-
ages the surfaces.
▶Do not use oven cleaner on the self-cleaning sur-
faces. If oven cleaner does get onto these surfaces,
dab it off immediately using water and a sponge
cloth. Do not rub the surface and do not use abras-
ive cleaning aids.
1. Remove accessories and cookware from the cook-
ing compartment.
2. Unhook the shelf supports and remove them from
the cooking compartment.
→"Shelf supports", Page19
3. Use a detergent solution and a soft cloth to remove
heavy soiling:
– From the cooking compartment floor
– From the inside of the appliance door
– From the glass cover for the oven light
This prevents stains that cannot be removed.
4. Remove any objects from the cooking compartment.
The cooking compartment must be empty.
14.3 Setting the cleaning function
Ventilate the kitchen while the cleaning function is run-
ning.
WARNING‒Risk of burns!
The outside of the appliance gets very hot when the
cleaning function is in progress.
▶Never touch the appliance door.
▶Allow the appliance to cool down.
▶Keep children at a safe distance.
Requirement:Prepare the appliance for the cleaning
function. →Page18
1. Use the function selector to set EcoClean ⁠.
aThe display shows the duration. The duration of
onehour cannot be changed.
2. Use the temperature selector to set the cleaning
setting ⁠.
aThe cleaning function starts after a few seconds and
the time counts down.
aOnce the cleaning function ends, an audible signal
sounds and the display shows the cooking time as
zero.
3. Switch off the appliance.
4. Wipe the appliance clean. →Page18
14.4 Wiping the appliance clean following
the cleaning function
1. Allow the appliance to cool down.
2. Wipe the cooking compartment clean with a damp
cloth.
Note:Marks may appear on the self-cleaning sur-
faces. Residues of sugar and albumin in the food
are not removed and remain on the surfaces. Red-
dish patches may be left over from salty food – the
spots are not rust. These spots are not harmful.
These marks do not impair the cleaning ability of
the self-cleaning surfaces.
3. Attach the shelf supports.
→"Shelf supports", Page19
15 Cleaning assistance
The cleaning assistance is a fast alternative for occa-
sionally cleaning the cooking compartment. The clean-
ing assistance softens dirt by vaporising the soapy wa-
ter. The dirt can then be removed more easily.
15.1 Setting the cleaning assistance
WARNING‒Risk of scalding!
If there is water in the cooking compartment when it is
hot, this may create hot steam.
▶Never pour water into the cooking compartment
when the cooking compartment is hot.
Requirement:The cooking compartment has cooled
down completely.
1. Remove the accessories from the cooking compart-
ment.
2. Mix 0.4litres water with a drop of washing-up liquid
and pour into the centre of the cooking compart-
ment floor.
Do not use distilled water.
3. Use the function selector to set the Bottom heat-
ing type of heating.
4. Use the temperature selector to set 80°C.
5. Press the button repeatedly until is highlighted
in the display.
6. Use the or button to set the time to
fourminutes.
aAfter a few seconds, the appliance starts heating
and the cooking time counts down.

Shelf supports en
19
aWhen the cooking time has elapsed, a signal
sounds and the duration is at zero in the display.
7. Switch off the appliance and leave the cooking com-
partment to cool down for 20minutes.
15.2 Recleaning the cooking compartment
ATTENTION!
The prolonged presence of moisture in the cooking
compartment leads to corrosion.
▶After using the cleaning assistance, wipe the cook-
ing compartment and allow it to dry completely.
Requirement:The cooking compartment has cooled
down.
1. Open the appliance door and remove the remaining
water with an absorbent sponge cloth.
2. Clean the smooth surfaces in the cooking compart-
ment with a dish cloth or a soft brush. Remove stub-
born food remnants using a stainless steel scouring
pad.
3. Remove limescale with a cloth soaked in vinegar.
Then wipe with clean water and rub dry with a soft
cloth (including under the door seal).
4. Once the cooking compartment is cleaned suffi-
ciently:
‒To allow the cooking compartment to dry, open
the appliance door to the stop position (approx.
30°) and leave it open for approx. onehour.
‒To dry the cooking compartment quickly, heat up
the appliance for approx. fiveminutes at 3Dhot
air and 50 °C while the door is open.
16 Shelf supports
To clean the rails and the cooking compartment, or to
replace the rails, you can remove these.
16.1 Detaching the shelf supports
WARNING‒Risk of burns!
The shelf supports get very hot
▶Never touch the shelf supports when hot.
▶Always allow the appliance to cool down.
▶Keep children at a safe distance.
1. Lift the rail forwards slightly and detach it ⁠.
2. Pull the whole rail to the front and remove it.
16.2 Attaching the shelf supports
Notes
¡The rails only fit on the right or left.
¡For both pull-out rails, ensure that you can pull them
forwards and out.
1. First, push the rail into the middle of the rear
socket until the rail rests against the cooking
compartment wall, and then push this back ⁠.
2. Push the rail into the front socket until the rail
also rests against the cooking compartment wall,
and then press this downwards ⁠.
3
4
16.3 Removing the pull-out rail
WARNING‒Risk of burns!
The shelf supports get very hot
▶Never touch the shelf supports when hot.
▶Always allow the appliance to cool down.
▶Keep children at a safe distance.
ATTENTION!
The self-cleaning surfaces in the cooking compartment
may be damaged by detaching and attaching the pull-
out rails.
▶Detach the rails before detaching or attaching the
pull-out rails.
Note:If necessary, you can use pull-out rails on all
levels.

en Shelf supports
20
1. Push on the tab marked PUSH behind the rail, and
push the rail to the rear.
2. Keep the PUSH tab pushed back and swing the
rail outwards ⁠.
3. Pull the rail out towards the front until the retainer at
the back unhooks.
4. Remove the pull-out rail.
5. Clean the pull-out rail.
→"Cleaning products", Page15
16.4 Attaching the pull-out rail
Note:The pull-out rails only fit on the right or left. Make
sure when you fit them that you can pull them out to-
wards the front.
1. Insert the pull-out rail between the two bars.
2. Push the retainer in between the lower and the
upper bar.
3. Keep the PUSH tab pushed in and swing the pull-
out rail inwards until the front retainer is located
between the two bars ⁠.
‒Release the PUSH tab.
aThe retainer clicks into place.