Bosch WOE802D0IN Specification sheet

en Instruction Manual and Installation Instructions
Washing machine
Top-loader C series

2
Your new washing machine
You have chosen a Bosch washing
machine.
Please take a few minutes to read and
become familiar with the advantages of
your washing machine.
To meet the high quality demands
required by Bosch, every washing
machine that leaves our factory is
carefully checked to ensure that it
functions correctly and is in perfect
condition.
For more information on our products,
accessories, replacement parts and
services, see our website www.bosch-
home.com or contact our after-sales
service centres.
If the operating and installation
instructions describe different models,
any differences will be pointed out at the
relevant points in the text.
Read these operating and installation
instructions before switching on the
washing machine.
Display rules
:Warning!
This combination of symbol and signal
word indicates a possibly dangerous
situation. Not heeding the warning can
cause death or injuries.
Caution!
This signal word indicates a possibly
dangerous situation. Not heeding the
caution can cause property and/or
environmental damage.
Note/tip
Information about the optimum use of
the appliance/any other useful
information.
1. 2. 3. / a) b) c)
The steps are represented by numbers
or letters.
■/ -
Lists are represented by a small box or
a dash.

en
3
Contents enInstruction Manual and Installation Instructions
5Installing and connecting the
appliance . . . . . . . . . . . . . . . . . . .4
Included with the appliance: . . . . . . . . 4
Installing the appliance . . . . . . . . . . . . 4
Connecting the appliance. . . . . . . . . . 6
Levelling the appliance . . . . . . . . . . . . 9
Before using the appliance for
the first time . . . . . . . . . . . . . . . . . . . . 9
9Quick reference guide . . . . . . . .10
*Familiarising yourself with
your appliance . . . . . . . . . . . . . .11
Appliance overview. . . . . . . . . . . . . . 11
Panel . . . . . . . . . . . . . . . . . . . . . . . . 12
YDisplay . . . . . . . . . . . . . . . . . . . .13
/Programme overview . . . . . . . .15
0Buttons . . . . . . . . . . . . . . . . . . . .17
ZLaundry. . . . . . . . . . . . . . . . . . . .19
Preparing the laundry . . . . . . . . . . . . 19
Sorting laundry . . . . . . . . . . . . . . . . . 19
1Operating the appliance . . . . . .20
Switching on the appliance
and setting a programme . . . . . . . . . 20
Programme settings . . . . . . . . . . . . . 20
Placing the laundry into the drum . . . 20
Adding detergent and fabric care
products . . . . . . . . . . . . . . . . . . . . . . 21
Starting a programme. . . . . . . . . . . . 22
Childproof lock . . . . . . . . . . . . . . . . . 22
Pausing programmes and adding
more laundry . . . . . . . . . . . . . . . . . . 22
Cancelling the programme . . . . . . . . 22
Resuming the programme when the
programme status is Rinse Stop . . . 22
Programme end . . . . . . . . . . . . . . . . 23
Removing laundry and switching off
the appliance . . . . . . . . . . . . . . . . . . 23
HSensors . . . . . . . . . . . . . . . . . . . 23
Unbalanced load detection system . .23
Continuous automatic load
adjustment function . . . . . . . . . . . . . .23
DCleaning and maintenance. . . . 24
Cleaning/Maintenance . . . . . . . . . . .24
Cleaning the drum. . . . . . . . . . . . . . .25
Descaling the appliance . . . . . . . . . .25
Cleaning the drain pump. . . . . . . . . .25
Cleaning the lint filter. . . . . . . . . . . . .26
3What to do in the event of
a fault . . . . . . . . . . . . . . . . . . . . . 27
Help with the appliance . . . . . . . . . . .27
Filter in water supply blocked . . . . . .29
LTransporting the appliance . . . 30
{Technical specifications. . . . . . 31
4After-sales service . . . . . . . . . . 32

en Installing and connecting the appliance
4
5Installing and
connecting the
appliance
Installingandconnecti ngtheappliance Included with the appliance:
1. Remove any packaging and
protective covers completely from
the appliance.
2. Remove the protective film from the
control panel.
3. Remove the appliance from the base
padding.
Note: Operating the appliance on
the base padding is strictly
forbidden.
4. Open the cover on the appliance
and take out all the accessories.
You can now install and connect the
appliance.
Caution!
Risk of material damage/damage to the
appliance
Objects remaining in the drum that are
not designed for operation with the
appliance may result in material
damage and damage to the appliance.
Remove these objects, along with all
accessories, from the drum.
Installing the appliance
:Warning
Risk of injury!
■The appliance is very heavy. Lifting it
may result in injury.
Do not lift the appliance on your
own.
Risk of injury!
■The appliance has sharp edges on
which you could cut your hands.
Do not take hold of the appliance by
its sharp edges. Wear protective
gloves to lift it.
Risk of injury!
■If the hoses and mains cables are
not correctly routed, they may
constitute a tripping hazard, which
may result in injury.
Route hoses and cables such that
they do not constitute a tripping
hazard.
(Water drain hose*
0Mains cable
8Water drain hose*
@Water supply hose
HSecond water supply hose
(identified by a red marking) on
models with a hot water supply
hose*
PSnap connector*
XBottom plate
* Depending on the appliance
specifications


#

+
3
;

Installing and connecting the appliance en
5
Installing the bottom plate
1. Lay the appliance down with its front
panel resting on a piece of soft
material.
2. Push the bottom plate onto the
underside of the appliance and
screw it in place.
Installation surface
Caution!
Risk of damage to the appliance
Frozen hoses may rupture or burst.
Do not install the appliance in areas that
may be exposed to frost or outdoors.
Note: The appliance must be stable so
that it does not "wander".
■The surface on which the appliance
is installed must be firm and level.
■Soft floors/floor coverings are not
suitable.
■All four of the appliance's feet must
stand firmly on the ground.
Hose and pipe lengths
■Connecting
Model with pump and a maximum load
of 14 kg or more:
Model with pump and a maximum load
below 14 kg:
Model without pump:
3LHFHRI
VRIWPDWHULDO
D Min. 86 cm - max. 120 cm
E 140 cm
F Max. 190 cm
G 150 cm
D Min. 86 cm - max. 100 cm
E 140 cm
F Max. 190 cm
G 150 cm
D Max. 15 cm
E 140 cm
F Max. 190 cm
G Max. 100 cm

en Installing and connecting the appliance
6
Connecting the appliance
Caution!
Risk of material damage/damage to the
appliance
■If the water pressure is too high or
too low, the appliance may not be
able to operate properly, and this
may also result in material damage
or damage to the appliance.
Ensure that the water pressure in the
water supply facility is at least 30
kPa (0.3 bar), and does not exceed
800 kPa (8 bar).
Material damage/damage to the appliance
■If the water hoses are altered or
damaged, this may result in material
damage or damage to the
appliance.
The water hoses must not be kinked,
crushed, altered or severed.
Material damage/damage to the appliance
■The use of hoses supplied by other
brands to connect to the water
supply may result in material
damage or damage to the
appliance.
Use the hoses supplied with the
appliance or genuine spare part
hoses only.
Notes
■In addition to the information listed
here, the local water and electricity
supplier may have special
requirements.
■If in doubt, have your appliance
connected by a professional.
Water supply hose
Notes
■When using a spanner, use the
correct size and apply controlled
force.
■Only operate the appliance using
mains water.
Connection to the universal tap
adapter
Note: When connecting to a threadless
tap, fit the supplied adapter first.
1. Slide the sliding sleeve downwards
from the snap connector (all balls
must be exposed) and then
disconnect the snap connector from
the connection socket.
2. Turn part B of the connection socket
until the clearance between part A
and part B is at least 5 mm.
3. Unscrew all of the screws from part
A.
4. Slide the connection socket over the
tap opening and then screw the
screws tightly back into part A.
(Connection socket
0Exposed balls
8Snap connector





âPP
$
%

Installing and connecting the appliance en
7
Note: Ensure the following:
■The tap's opening is smooth and
even.
■The seal is positioned centrally with
respect to the tap opening.
5. Retighten part B.
6. Slide the sliding sleeve downwards
from the snap connector (all balls
must be exposed), insert the snap
connector into the connection socket
and slide it upwards.
Model with hot water supply:
1. Connect the red-marked hot water
supply hose to the hot water tap (¾";
max. 60 °C) and to the red valve on
the appliance, and connect the blue-
marked cold water supply hose to
the cold water tap (¾") and to the
blue valve on the appliance.
2. Carefully turn on the taps and check
that there are no leaks.
Notes
– The threaded connection is
subject to high water pressures.
– Both hoses must be connected in
order for the appliance to work
correctly.
Model without hot water supply:
1. Connect the water supply hose to
the tap (¾") and to the valve on the
appliance.
2. Carefully turn on the taps and check
that there are no leaks.
Note: The threaded connection is
subject to high water pressures.
Water drainage
Caution!
Water damage
When water is being pumped away, the
drain hose is under high water pressure
and may slip out of the wash basin or
connection point.
Secure the drain hose so that it cannot
slip out.
Caution!
Damage to the appliance/laundry
If the end of the drain hose is immersed
in the drained water, water may be
sucked back into the appliance and
may damage the appliance/laundry.
Make sure that:
■The wash basin outlet is not blocked,
■The end of the drain hose is not
immersed in the drained water,
■The water drains away quickly
enough.

en Installing and connecting the appliance
8
Connect the water drain hose as
follows:
1. Use the spring clip to secure the
water drain hose to the outlet on the
appliance.
Note: Only for appliances with a
separate water drain hose.
2. Second end of the water drain hose:
– For models with a pump, attach it
to a waste pipe or hang it in a
wash basin.
Note: The height difference between
the surface on which the appliance
is installed and the drain pipe must
be between 86 and 100 cm or 120
cm, depending on the product
variant.~Page 5
– For models without a pump,
secure it in a floor drain.
Notes
– The height difference between
the surface on which the
appliance is installed and the
water drain hose should be no
more than 15 cm.
– If you extend the drain hose, its
total length should be no more
than 3 m. Otherwise, the water
will not be able to drain away
properly.
Electrical connection
:Warning
Risk of electric shock/fire/material
damage/damage to the appliance!
If the appliance is not installed properly,
this may lead to a dangerous situation.
Ensure the following:
■The mains voltage on your power
socket must match the rated voltage
specified on the appliance
(identification plate). The connected
loads and the required fuse
protection are specified on the
identification plate.
■The appliance must only be
connected to alternating voltage via
a protective contact socket that has
been correctly installed. This plug
socket must be freely accessible at
all times.
■The mains plug and the protective
contact socket must match and the
earthing system must be correctly
installed.
■The installation must have an
adequate cross section.
■The mains plug must be freely
accessible at all times. If this is not
possible, in order to comply with the
relevant safety regulations, a switch
(all pole disconnection) must be built
into the permanent installation in
accordance with electrical
installation regulations.

Installing and connecting the appliance en
9
■If using a residual current circuit
breaker, only use one that bears the
following mark: z. The presence of
this mark is the only way to be sure
that it fulfils all the applicable
regulations.
Connect the appliance to the mains
power supply as follows:
1. Plug the appliance's mains plug into
the designated socket.
2. Check that the mains plug is in
securely.
Levelling the appliance
Level the appliance as follows:
Adjust the height of the appliance feet
to level the appliance. Tighten the lock
nuts on all the appliance's adjustable
feet against the housing. As you do so,
hold the foot tight and do not adjust its
height. Use the spirit level on the control
panel to check whether the appliance is
level.
Note: If the appliance is ever moved,
check that it is still level and re-level it if
necessary.
Before using the appliance for
the first time
Before you switch on the appliance:
Check that there is no visible damage to
the appliance. Do not operate the
appliance if it is damaged. Should you
have any problems, please contact your
specialist dealer or our after-sales
service.
Your appliance has been thoroughly
tested before leaving the factory. To
remove any water that may be left over
from testing, run the first wash cycle
without any laundry.
Run a program without laundry as
follows:
1. Press #to switch on the appliance.
2. Set the Tub clean/Tub Clean
program.
3. Open the appliance lid (but do not
place any laundry inside).
4. Pull out the detergent drawer.
5. Fill compartment Iwith washing
power, or fill compartment II with
liquid detergent.
6. Close the detergent drawer.
7. Press A.
The program will start.
8. Switch off the appliance at the end of
the program.
Your appliance is now ready to use.
Level
Not level

en Quick reference guide
10
9Quick reference guide
Quickreferenceguide
--------
--------
--------
--------
1
Before starting
the program:
@@@
Sort the laundry. Turn on the water
tap.
Load the laundry.
2@@@
Add detergent. Close the appliance
lid.
Switch on the
appliance.
Set a program.
3@
If necessary, adjust
the programme
settings.
Start the
programme.
4
Once the
programme has
ended:
@ @
Open the lid and
remove the laundry.
Turn off the tap.

Familiarising yourself with your appliance en
11
*Familiarising yourself with your appliance
Familiari singyourself withyour appliance Appliance overview



#
(Control and display panel
0Filter bag
8Detergent drawer
@Appliance lid

en Familiarising yourself with your appliance
12
Panel
Model without a hot water supply hose:
Model with a hot water supply hose:
 
#
3
+
 
#
3
+
(Main switch
Press this button to switch the appliance on or off.
0Display
Displays settings and information. ~Page 13
8Display panel
Displays settings and information.
@Buttons
To set a program and adjust the program settings.~Page 17
HStart button
To start or interrupt a program or select the automatic program.
PSpirit level
Allows you to check whether the appliance is level.~Page 9

Display en
13
YDisplay
Display
Number/code Description Information
e.g. 50 Wash/spin cycle
duration
Expected wash/spin cycle duration (Nwash/Wash and 0Spin) in
minutes.
e.g. 2 Rinse cycles Number of rinse cycles (ORinse) in the set program.
e.g. 04 Program start
delay
Delay to the program start in hours if you have activated the Delay
start/Delay Start program setting.
E1 Water supply The machine is not filling with water properly (unable to reach default
water level). Make sure that:
■The tap is fully open.
■The supply hose is not kinked or trapped.
■The filter in the water supply is not blocked. ~Page 29
E2 Water outlet The drain pump or drain hose/drain pipe is blocked:
■Clean the drain pump ~Page 25
■Clean the drain hose/drain pipe
E3 Open lid The lid must be fully closed when a program is in progress.
■Close the lid and press the Start button
■Remove any trapped laundry
E4 Unbalanced load ■The laundry is not evenly distributed in the drum, creating an
imbalance.
Note: The appliance has an unbalanced load detection system,
which interrupts the spin cycle when the laundry is unevenly dis-
tributed.
Redistribute the laundry by hand to eliminate the imbalance.
■Adjust the height of the appliance feet to level the appliance.
~Page 9

en Display
14
--------
CL Note The lid has been opened while the child lock/Child Lock/
Child lock was active.
1. Switch off the appliance.
2. Wait 5 seconds.
3. Switch the appliance on again.
F0-F8 Other faults 1. Switch off the appliance.
2. Wait 5 seconds.
3. Switch the appliance on again.
If the fault occurs repeatedly, call the after-sales service.

Programme overview en
15
/Programme overview
Programmeoverview
Program/type of laundry/information Load size
Name of program
Brief explanation of the program and the items for which it is suitable.
Recommended load (in
relation to the maxi-
mum load
~Page 31)
Cotton/Daily Wash
Hard-wearing items made of cotton, linen or blended fabrics
Full load
Delicates/Soft
For delicate washable items, e.g. made of satin, synthetic fibres or blended fab-
rics.
Note: Use a detergent that is suitable for machine-washing delicate fabrics.
1/2 load
Soak/Dynamic Soak/Refresh
Before the main wash cycle starts, the laundry remains in the water for 30 min to
remove heavy soiling. To be used for particularly stubborn soiling.
Note: To avoid discolouration, only soak laundry of the same colour together.
Full load
Intensive
Hard-wearing items made of cotton, linen or blended fabrics. Program with a high
water level and long wash, rinse and spin cycles. Suitable for heavily soiled laun-
dry.
Full load
Quick/Quick Wash
Suitable for small items of lightly soiled laundry.
1/3 load
Memory
This allows you to save a selected program with your favourite settings:
1. Switch on the appliance.
2. Set the Memory program.
3. Adjust the program settings if necessary or start the program.
Note: When you set the Memory program again the next time you wash laundry,
the parameters you last set will still be active.
-
Air Dry
Program for drying hard-wearing fabrics and fabrics that do not repel water. The
laundry is spun and air-dried at a reduced speed.
Full load

en Programme overview
16
--------
Tub clean/Tub Clean
Program for cleaning and caring for the drum and the impeller, e.g. before run-
ning the first wash cycle or if an odour has developed after an extended period of
non-use.
Notes
■We recommend running this program once a month.
■Run the Tub clean/Tub Clean program without any laundry.
■Use standard washing powder or a detergent that contains a bleaching
agent. To prevent foaming, only use half the amount of detergent recom-
mended by the detergent manufacturer. Do not use detergents intended for
woollens or delicates.
Empty
Auto Start/One Touch Start
The washing program and water level are set automatically depending on the
load.
Note: The washing program starts immediately and the program duration is
shown on the display. Ensure the following beforehand:
■The laundry is placed into the drum.
■The detergent has been added.
Setting Auto Start/One Touch Start:
1. Press #to switch on the appliance.
2. Press A.
Note: If laundry is heavily soiled, chose a program suitable for the type of fabric.
-
Rinse
Laundry is rinsed and then spun, and the rinsing water is pumped away.
Setting the Rinse program:
1. Press #to switch on the appliance.
2. Press ORinse.
3. Press A.
-
Spin
Laundry is spun only, and the rinsing water is then pumped away.
Setting the Spin program:
1. Press #to switch on the appliance.
2. Press 0Spin.
3. Press A.
-

Programme overview en
17
0Buttons
Program setting Function
Once you have set a program, you will be shown default program settings. These are recommendations for
the set program and may vary. Depending on the program, you can adjust or activate/deactivate the pro-
gram settings to optimise the washing process for your laundry.
You can find out how to adjust program settings on ~Page 20
Nwash/Wash Once the programme has been set, the wash cycle's preset duration will be dis-
played.You can adjust the duration of the wash cycle.
ORinse Adjusting the number of rinse cycles:
Once the program has been set, the preset number of rinse cycles will be displayed.
You can adjust the number of rinse cycles.
0Spin Adjusting the duration of the spin cycle:
Once the program has been set, the spin cycle's default duration will be displayed.
You can adjust the duration of the spin cycle.
Rinse Hold:
If you deselect the spin cycle, your laundry will remain in water after the final rinse
cycle.
For reducing creasing when the laundry is not taken out of the appliance immediately
after the program ends.
Program When you switch on the appliance, the Auto Start/One Touch Start program is set
by default. If required, you can change the program before the program starts.
Water Level Once the program has been set, the program's default water level will be displayed.
You can adjust the water level if required.
Notes
■If the water level is not shown on the display, the program you are using is one in
which the appliance automatically adjusts the water level according to the size of
the load. You can still manually adjust the water level when using these programs
if you need to.
■Only set a low water level for light loads.
Temp. cold/Cold: Draw water from the cold water supply hose only.
warm/Warm: Draw water from the hot and cold water supply hoses.
hot/Hot: Draw water from the hot water supply hose only.
Note: Depending on the appliance specifications, water may be drawn from both hot
and cold water supply hoses in the hot/Hot setting.
SpeedPerfect/
Speed Perfect
For a shorter wash time with a comparable washing result to the standard program
setting. Please note that the energy consumption with this setting is higher than with
standard program settings.
Note: Pressing the Temp., Water Level or Delay start/Delay Start button resets the
SpeedPerfect/Speed Perfect setting.

en Programme overview
18
--------
Delay start/Delay
Start
You can use the Delay start/Delay Start button to delay the time at which the pro-
gram starts by up to 24 hours.
Your chosen time in hours, e.g. 8 h, is shown on the display and counts down until the
program starts. Once the program has started, the program duration will be dis-
played.
Note: If you activate the Delay start/Delay Start program setting, the Auto Start/
One Touch Start function will not be available.
Soil Level You can specify how heavily soiled your laundry is. The appliance adjusts the intensity
of the drum movement according to how heavily soiled the laundry is.

Laundry en
19
ZLaundry
Laundry Preparing the laundry
Caution!
Risk of damage to the drum and
laundry
Leaving objects in the pockets of your
clothing can cause damage to the drum
and laundry when the appliance is in
operation. Remove all objects (e.g.
metal items) from clothing pockets.
Prepare the laundry as follows:
■Empty all pockets.
■Tie cloth belts, apron strings, etc.
together.For small items of laundry,
such as socks and stockings, use a
laundry bag.
■Always wash small and large items
of laundry together.
■Close any zips, Velcro, hooks, loops
or buttons.
■Brush sand out of pockets and
collars.
■Remove curtain fittings or place
curtains in a laundry bag.
■Pre-treat stains while they are fresh.
First, dab stains with soapy water
without rubbing them.
Note: Stubborn or dried-in stains
can sometimes only be removed by
washing several times.
Sorting laundry
Sort your laundry according to the care
instructions and the manufacturer's
information on the care labels, using the
following criteria:
■Type of fabric/fibre
■Colour:
Laundry may become discoloured.
Wash white and coloured laundry
separately. Wash new coloured
items on their own the first time you
wash them.
■Soiling:
Wash laundry with the same level of
soiling together.
■Care labels:
The following symbols tell you which
programs you can and cannot use.
The numbers in the symbols indicate
the maximum recommended
washing temperature.
MSuitable for a normal washing
process, e.g. the Cotton/Daily
Wash program.
NA gentle washing process is
required, e.g. the Delicates/
Soft program.
OA particularly gentle washing
process is required, e.g. the
Delicates/Soft program.
ŽDo not machine wash.

en Operating the appliance
20
1Operating the
appliance
Operati ngtheappliance Switching on the appliance
and setting a programme
Note: The appliance must be correctly
installed and connected. ~Page 4
1. Press #to switch on the appliance.
2. Press Program repeatedly to set the
washing program you require.
Note: To set the Rinse, Spin und
Auto Start/One Touch Start
programs, follow the instructions in
the program overview.~Page 15
The corresponding indicator light will
light up and the default program
settings will be shown on the display
panel.
3. Adjust the programme settings if
required.
Programme settings
Once you have set a program, you will
be shown default program settings.
Before the program starts, you can
adjust or activate/deactivate the
settings that can be selected. An
overview of all the settings that can be
selected can be found from
~Page 17 onwards.
You can do the following to program
settings:
■Activate/deactivate them
■Adjust them
Adjusting or activating/deactivating:
Press the button for the relevant
programme setting repeatedly.
The indicator lights for the activated
programme settings will be continuously
lit/will flash and the values shown on the
display may change.
Placing the laundry into the
drum
Note: Do not exceed the appliance's
maximum load. If you overload the
appliance, it will not be able to wash the
laundry as effectively and the laundry is
more likely to crease.~Page 31
1. Prepare and sort the laundry.
2. Open the lid.
Check that the drum is completely
empty. Empty it if necessary.