BOSSCO ODOROX User manual

Safety Informaon ..................................................................................... 1
Contents List .............................................................................................. 2
Odorox® Boss™ Operaonal Guidelines .................................................... 3
Operang The Odorox® Boss™ .................................................................. 4
Care Instrucons ....................................................................................... 5
Opc Replacement Instrucons ................................................................ 6
Troubleshoong Guide .............................................................................. 7
Specicaons And Warranty ..................................................................... 8
TABLE OF CONTENTS

PLEASE READ AND SAVE
THESE IMPORTANT SAFETY
INSTRUCTIONS
IMPORTANT SAFEGUARDS
When using electrical equipment, basic
safety precautions should always be
followed to reduce the risk of re, electric
shock, and injury to persons, including the
following:
• Read all instructions before using this
Hydroxyl Generator.
• To avoid re or shock hazard, plug the
equipment directly into a grounded AC
electrical outlet.
• If the generator is covered by a bag when
shipped: remove plastic bag before use.
• Keep the cord out of heavy trafc areas.
To avoid re hazard, NEVER put the cord
under rugs, near heat registers, radiators,
stoves, or heaters.
• To protect against electrical hazards, DO
NOT immerse in water or other liquids. DO
NOT use near water.
• DO NOT leave the generator in use
unattended around those requiring close
supervision.
• WARNING! Always unplug the generator
before moving it, cleaning, or whenever the
generator is not in use. Be sure to pull by the
plug and not the cord.
• NEVER drop or insert any object into any
openings.
• DO NOT operate any generator with a
damaged cord or plug, if motor fan fails to
rotate, after the generator malfunctions, or
if it has been dropped or damaged in any
manner. Return generator to manufacturer
or authorized repair facility for examination,
electrical or mechanical adjustment, or repair.
• Use generator only for intended use as
described in this manual. Any other use
not recommended by the manufacturer
may cause re, electric shock, or injury
to persons. The use of attachments not
recommended may cause hazards.
• INDOOR USE ONLY!
• NEVER block the air openings, grills/outlets
or place on a soft surface such as a bed or
sofa, as this could cause the unit to tip over,
blocking the Air Intake Opening/Grill.
• Keep unit away from heated surfaces and
open ames.
• CAUTION: For General Ventilating Use
Only. Do Not Use to Exhaust Hazardous or
Explosive Materials and Vapors.
• DO NOT attempt to repair or adjust any
electrical or mechanical functions on this
unit. Doing so will void your warranty.
The inside of the unit contains no user
serviceable parts. All servicing should be
performed by qualied personnel only.
• WARNING! To reduce the risk of re or
electric shock, DO NOT use this generator
with any solid-state speed control device.
• DO NOT place anything on top of generator.
• DO NOT plug the cord in with wet hands:
electric shock could result.
• NEVER use detergents, gasoline, glass
cleaner, furniture polish, paint thinner or
other household solvents to clean any part
of the generator.
• DO NOT, under any circumstances, cut or
remove the third (Ground) prong from power
cord. For personal safety, this generator
must be properly grounded.
WARNING!
Use this Hydroxyl Generator only for its intended
purpose as described in this Owner’s Manual.
SAFETY INFORMATION

The Odorox® Boss™ Hydroxyl Generator is shipped with the following:
1. Odorox® Boss™ Hydroxyl Generator
2. Washable Filter (Comes Installed)
3. Set of Keys
4. Owner’s Manual
5. Warranty Card
CONTENTS LIST

ODOROX
®
BOSS™ OPERATIONAL GUIDELINES
The Odorox® Boss™ unit is the right
choice for the professional re and
water damage restoraon contractor.
It can deodorize and decontaminate up
to 2000 square feet.
The Odorox® Boss™ unit is designed for heavy concentration processing and
operates using less than 230 Watts (refer to Specication page for additional
ratings). The Boss™ unit is equipped with a selector switch for 1 or 2 Odorox®
hydroxyl generating optics and a washable lter. The built-in fan is adjustable
from approximately 250 to 500 cfm which makes this unit very versatile. Turn
the fan to low to deodorize small areas such as cars, RVs, boats, bedrooms or
ofces. This setting is also ideal for tenting damaged contents on-site. Turn
the fan to high and you have the ability to treat larger areas such as basements,
homes and businesses. In this case, auxiliary air movers should be used to help
evenly distribute the Odorox® hydroxyls.
For use in heavy odor concentrations, the best performance will take place if the
washable lter is removed prior to start up. This will ensure that the Odorox®
Boss™ unit continues to treat the source of the odors and does not also need to
treat odors coming from accumulation on the lter.
Recommended treatment area per Boss™

POWER ON
The main power for the Boss™ unit can
be switched on by turning the FAN SPEED
switch clockwise.
POWER OFF
The main power for the Boss™ unit can
be switched off by turning the FAN SPEED
switch counter clockwise to the
“OFF” position.
FAN SPEED
The Boss™ unit is equipped with a fan, which operates at between 250 and 500
cubic feet per minute.
In order for the fan to turn on, the FAN SPEED switch must be rotated clockwise.
Once turned on, the fan speed can be controlled by turning the FAN SPEED switch
clockwise to decrease the speed, or counter clockwise to increase the speed.
PROCESSOR
The Boss™ unit is equipped with two Odorox® hydroxyl generating optics. In
order for the optics to turn on, the FAN SPEED switch must be turned on.
With the FAN SPEED switch turned on, and the PROCESSOR switch in the LOW
position, one optic will be functioning. With the FAN SPEED switch turned on,
and the PROCESSOR switch in the HIGH position, two optics will be functioning.
With the FAN SPEED switch in the OFF position, the optics will likewise be off.
OPERATING THE ODOROX
®
BOSS™ UNIT

CARE INSTRUCTIONS
CAUTION: DISCONNECT the unit from an electrical power source
before performing any maintenance or cleaning on the unit.
SYSTEM CASE CLEANING
Exterior
The exterior of the Odorox® product can be cleaned with mild dishwashing
detergent and a clean cloth, and then rinsed with clean water. DO NOT use any
all-purpose cleaners with harsh detergents or abrasives, as these may damage
the exterior of the equipment and void any warranty. Care should also be
taken to avoid spraying or otherwise directing detergent or water into or around
electrical components.
Interior
The interior of the Odorox® product can be cleaned in the same manner as the
exterior with the exception of the optics and optics’ housing.
OPTIC CLEANING
Cleaning of the Odorox® optics is recommended to maintain peak processing
efciency. Fingerprints, smudges, dirt, dust particles, etc. will interfere with the
hydroxyl production and should be avoided.
Note: Remove the optics from the optic chamber prior to cleaning to avoid
any damage to the optics during the cleaning process (refer to the Optic
Replacement Instructions for proper removal).
To clean the optics, use a solution of 10% Isopropyl Alcohol and 90% ltered/
distilled water on a clean lint-free cloth and wipe gently. Do not use any type of
commercial glass cleaner. Using another lint-free cloth, gently wipe the optic until
completely dry. Allow the optic to dry completely before operating the system.

OPTIC REPLACEMENT INSTRUCTIONS
CAUTION: DISCONNECT the unit from an electrical power source before
performing any maintenance or cleaning on the unit.
Step 1 – Turn “FAN SPEED” switch to the “OFF” position
Step 2 – Unplug power cord from the electrical receptacle
Step 3 – Using the supplied key, unlock and remove both end panels
Step 4 – Remove lter cover plate and lter
Step 5 – Remove optic following these instructions:
Cauon: Use clean powder free latex gloves and eye protecon when
handling the opcs in this unit
• With a firm grip on the upper porcelain end of the optic, use your other hand to
grip the optic connector..
• Gently ‘wiggle’ connector while pulling from the optic base.
• Gently pull optic from three lamp supports (Do not put any pressure on the
side of the optic without support).
Cauon: Opcs contain Mercury. Dispose of opcs in accordance with
local regulaons. To nd out more about local regulaons, please visit
www.lamprecycle.org.
Step 6 – Install new optic following these instructions:
• Remove new optic from packaging and gently insert into the three optic clips.
• With a rm grip on the upper porcelain end of the optic, use your other hand to
grip the optic connector.
• Gently connect the optic connector to the optic.
Note: Optic connector is keyed with the optic base and will connect in
one direction only
• Ensure optic connector and optic base are rmly pressed together.
Step 7 – Re-install end panels
Step 8 – Re-install lter and lter plate
Step 9 – Plug power cord back into the electrical receptacle
Step 10 – Test unit for proper operation

TROUBLESHOOTING
PROBLEM POSSIBLE CAUSE SOLUTION
Fan will not turn on Boss™ unit is not plugged
into an energized electrical
receptacle.
Ensure circuit breaker is
‘ON’ and the electrical
receptacle has proper
power available.
Internal component failure. Contact local distributor for
service.
Green “PROCESSOR ON”
LED will not light up
“FAN SPEED” switch is in
the “OFF” position.
Turn on “FAN SPEED”
switch to desired air ow
setting.
Green LED has failed. Contact local distributor for
service.
Internal component failure. Contact local distributor for
service.
Optic(s) not functioning Rated life of optic has
been met.
Contact local distributor for
replacement optics/service.
Optics have been
damaged.
Contact local distributor for
replacement optics/service.
Internal component failure. Contact local distributor for
service.

SPECIFICATIONS AND WARRANTY
SPECIFICATIONS
Dimensions: 12.5” x 18.5” x 25” (307mm x 470mm x 635mm)
Weight: 35lbs (16kg)
Power Requirements: 120 Volt AC, 1.9 Amp, 60 Hz (North America Model)
240 Volt AC, 0.9 Amp, 50 Hz (International)
Control: Variable Speed Switch/Selector Switch
Meter: 1/10 Quartz Hour Meter
Mobility: Handle/Rubber Feet, Optional Wheeled Cart
Noise Level: <55 dBA
Number of Optics: 2
REPLACEMENT PARTS
HGI PART # QUANTITY IN EACH
BOSS™ UNIT
PART DESCRIPTION
OPT-XX-078 2 ODOROX® HYDROXYL GENERATING
OPTIC, BROWN
XSA00EW02 2 OPTICS POWER CABLE
XSA00EA01 2 BALLAST ASSEMBLY, 120 VOLT (N.Am)
XSA00EA06 2 BALLAST ASSEMBLY, 200-277 VOLT,
50/60 Hz (INTL)
EPC-IL-021 1 LIGHT MODULE, PROTECTED LED,
110-120VAC, GREEN (N. Am.)
EPC-IL-017 1 LIGHT MODULE, PROTECTED LED,
230/240VAC, GREEN (INTL)
XSA00EA04 1 HOUR METER ASSEMBLY, 90-264 VAC,
50/60 Hz
XSA00EA02A 1 SPEED CONTROL, 120 VOLT (N.Am)
ESC-XX-542 1 SPEED CONTROL, 240 VOLT (INTL)
ESC-KN-075 1 SPEED CONTROL KNOB
LIMITED WARRANTY
HGI Industries, Inc. warrants that this Odorox® product (excluding spare parts
and consumables) shall be free from defects in workmanship or materials for a
period of one (1) year from the delivery thereof to the customer.

CONTACTING YOUR LOCAL DISTRIBUTOR
For replacement parts, warranty service, or any questions regarding the
operation and maintenance of your Odorox® product, please contact your
local Odorox® distributor.
To nd a distributor in your area, please visit: www.Odorox.com
Odorox® Hydroxyl Generators are proudly manufactured in the USA.
HGI Industries, Inc.
2055 High Ridge Road
Boynton Beach, FL 33426
Toll Free: 877.735.3701
www.hgiind.com
Copyright © 2011, HGI Industries Incorporated
Odorox and Boss are trademarks or registered trademarks of HGI Industries Incorporated, Boynton Beach, Florida USA.