Boston Acoustics P4TS User manual

P460,P450,
P442,P430,
P400
P460
P450
P442
P400
P4TS
P430
Compact Stand for the P4, Bravo®II, and Bravo Speakers

Required Tools: (not included)
•Pliers*
*Required for Bravo II and Bravo only
•Flat head
Screwdriver
•Phillips head
Screwdriver
Speaker screw (short)
x 2 M5 x 18 Threaded
Machine Screw
x 3
P4TS Base
x 1
P4TS
Horizontal Post
x 1
Split Washer (large)
x 2
1⁄4"-20 Threaded Nut
x 2
P4TS Included Hardware:
Speaker Screw (long)
x 2
P4TS
Vertical Post
x 1
P4TS Included Parts:
81⁄4"
210mm
61⁄2"
165mm
23⁄4"
70mm
47⁄8"
123mm
23⁄4"
70mm
14 7⁄32"
136mm
Split Washer (small)
x 3
Rubber Feet
x 6
Plug
x 1

Step Three: Mounting the P4 Speaker
Due to the weight of the P4 speaker,it is recommended that the
installation be performed with the P4 speaker laying face down with
the grille removed on a soft surface such as a plush carpeted floor
or the P4 shipping carton. Inspect the area wherethe speaker will
lay making sure that there are no objects that could damage the
speakers or scratch the front of the P4.
1. Position the P4TS close to the P4 speaker as illustrated.
2. Connect the speaker wireto the terminals on the P4 speaker.
3. Mount the speaker to the post by lining up the two threaded
inserts in the back of the P4 speaker with the two outside
machined holes (middle hole is not used) in the post. Insert the
two speaker screws (short) and tighten. Insert the plug into the
unused machined hole on the post.
Note: Do not over-tighten the screws.
4. Take up any slack in the speaker wireby gently pulling the wire
at the opening in the base.
P4 Vertical Mount Assembly Instructions:
This configuration is compatible with Models: P460,
P450, P442, and P430.
•Flat head
Screwdriver
Hardware / Parts:
Required Tools:
•Phillips head
Screwdriver
Speaker
Screw
(short) x 2
Threaded
Machine
Screw x 3
P4TS
Base x 1
P4TS
Vertical
Post x 1
Step One: Attach Base
Attach the base to the vertical
post with the three included
threaded machine screws and
split washers (small) using a
Phillips head screwdriver. The
post has already been threaded
to ease screw installation. Attach
rubber feet to base.
Step Two: Speaker Wire
With the stand still inverted, route
the speaker wirethrough the
opening in bottom of the base,
down through, and out the open-
ing in the post. Use the top open-
ing for the P430 and P442 and the
bottom opening for the P450 and
P460. Leave several extra inches of
speaker wire exposed to ease con-
nection with the P4 speaker.
Split Washer
(small) x 3
Plug
x 1

Step Three: Mounting the P4 to the Stand
1. Using the speaker screws (long) and speaker screws
(short), mount the P4 wall bracket to the P4TS post.
The wall bracket is threaded to accept the speaker
screws. Use the speaker screws (long) on the upper
two threaded inserts and the speaker screws (short)
on the lower two threaded inserts.
2. Mount the retaining screws (included with P4 speaker)
and connect the speaker wire to the terminals on the
back of the P4 Speaker.
3. Slide the speaker into the retaining channels. The
speaker is held in place by gravity.
Note: For detailed instructions on installing the speaker to the wall
bracket, please refer to the P4 owners manual.
4. Take up any slack in the speaker wireby gently
pulling the wireat the opening in the base.
P4 Horizontal Mount Assembly Instructions:
This configuration is compatible with Models: P460,
P450, P442, P430, and P400.
Hardware / Parts:
Required Tools:
Speaker
Screw
(long) x 2
Threaded
Machine
Screw x 3
P4TS
Base x 1
P4TS
Horizontal
Post x 1
Step Two: Speaker Wire
With the stand still inverted, route
the speaker wire through the
opening in bottom of the base, down
through, and out the opening near
the top of the post. Leave several
extra inches of speaker wire exposed
to ease connection with the P4
speaker.
Step One: Attach Base
Attach the base to the horizontal
post with the three included
threaded machine screws and
split washers (small) using a
Phillips head screwdriver. The
post has already been threaded
to ease screw installation. Attach
rubber feet to base.
•Flat head
Screwdriver
•Phillips head
Screwdriver
Speaker
Screw
(short) x 2
Split Washer
(small) x 3

Step Three: Mounting the Bravo Speaker
1. Using the speaker screws (long), washer,
and 1⁄4"-20 threaded nut, mount the
Bravo mounting bracket to the P4TS
post.
2. Remove the speaker’s grille by grasping
the back of the cabinet in one hand,
while gently pulling the grille away with
the other hand.
3. Connect the speaker wire to the
terminals on the Bravo speaker.
4. Align the openings in the back of the speaker with the two
posts protruding from the bracket as shown and attach the
speaker to the bracket by inserting the supplied screws
through the holes in the front of the speaker and into the
bracket as shown. Insert the plug into the unused machined
hole on the post. Note: For detailed instructions on installing the
speaker to the wall bracket, please refer to the Bravo owners manual.
4. Take up any slack in the speaker wireby gently pulling the wire
at the opening in the base.
Bravo Vertical Mount Assembly Instructions:
This configuration is compatible with Models: Bravo II
and Bravo.
Hardware / Parts:
Required Tools:
Speaker
Screw
(long) x 2
Threaded
Machine
Screw x 3
P4TS
Base x 1
P4TS
Vertical
Post x 1
Step Two: Speaker Wire
With the stand still inverted, route
the speaker wirethrough the
opening in bottom of the base,
down through, and out the slot in
the opening near the top of the
post. Leave several extra inches of
speaker wire exposed to ease
connection with the Bravo speaker.
Step One: Attach Base
Attach the base to the vertical
post with the three included
threaded machine screws and
split washers (small) using a
Phillips head screwdriver. The
post has already been threaded
to ease screw installation. Attach
rubber feet to base.
•Pliers
•Flat head
Screwdriver
•Phillips head
Screwdriver
Split
Washer
(large)
x 2
1⁄4"-20
Threaded
Nut x 2
Split
Washer
(small)
x 3
Plug
x 1

Boston, Boston Acoustics, Bravo, and the Boston Acoustics
logo are registered trademarks of Boston Acoustics, Inc.
Specifications aresubject to change without notice.
© 2004 Boston Acoustics, Inc.
300 Jubilee Drive
Peabody,MA 01960
U.S.A.
978.538.5000
www.bostonacoustics.com 042-002139-1
If Service Seems Necessary
First, contact the dealer from whom you purchased the speakers. If that is not possible, write to:
Boston Acoustics, Inc.
Attn: Parts and Service
300 Jubilee Drive
Peabody, MA 01960 U.S.A.
Or contact us via e-mail at:
[email protected]
We will promptly advise you of what action to take. If it is necessary to return your P4TS compact stand to the
factory, please ship it prepaid. After it has been repaired, we will return it freight prepaid in the U.S.A. and Canada.