Bounty Hunter Time Ranger User manual

Time Ranger™
Metal Detector
Owner’s Manual
The Time Ranger™ is a top-of-the line professional metal detector
with high-end features for the serious metal detectorist. A large LCD
panel displays current operating status at all times during operation
in the field. All feaures and functions are highly visible, with no
hidden programming, making your Time Ranger™ easy to use.
◆Microprocessor-controlled
◆Programmable operation
◆Programmable targets
◆LCD target readout
◆Touch pad selection
◆Numbered target values
◆SMART TRAC ground control
Carefully read this entire manual before attempting to operate
your new Time Ranger™ Metal Detector.

Contents
The Basics of Metal Detecting . . . . . . . . . . . . . . . . . . . . . . . . 1
Metal Types . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Discrimination . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Depth Detection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Ground Balancing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Quick Start . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Getting Started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
To assemble the Time Ranger™ . . . . . . . . . . . . . . . . . . . . . . . . . 3
Batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
To install the batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
To check the batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Headphones. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
To connect and use headphones. . . . . . . . . . . . . . . . . . . . . . . . . 5
Control Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Probable Target ID fields. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Touch pads . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
LCD Display. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
TARGET Readout. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Target Value Reference . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Dials . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Basic Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Turning the Detector ON. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
DISCRIMINATION Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
To accept all targets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
To select PRESET targets. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
To select customized targets. . . . . . . . . . . . . . . . . . . . . . . . . . . 16
To adjust sensitivity in DISCRIMINATION mode . . . . . . . . . . . . . . 18
To listen to tones in DISCRIMINATION mode. . . . . . . . . . . . . . . . 18
To turn on the BLANKER feature . . . . . . . . . . . . . . . . . . . . . . . 19
To operate the unit in SNIFF Mode . . . . . . . . . . . . . . . . . . . . . . 19
ALL METAL Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
To select ALL METAL mode . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
To adjust sensitivity in ALL METAL mode . . . . . . . . . . . . . . . . . . 22
To adjust detector when ground conditions change. . . . . . . . . . . . 22
To update ground balancing. . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Testing the detector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Ground Testing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Air Testing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Using the Detector in the Field . . . . . . . . . . . . . . . . . . . . . . 26
Coil Movement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Pinpointing the target . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
False signals and chatter . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Ground Balancing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Resetting the detector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Detector Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Coinshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Recommended Mode of Operation . . . . . . . . . . . . . . . . . . . . . . 30
Relic Hunting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Recommended mode of operation . . . . . . . . . . . . . . . . . . . . . . . 32
Jewelry Hunting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Recommended mode of operation . . . . . . . . . . . . . . . . . . . . . . . 34
Gold Prospecting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Recommended mode of operation . . . . . . . . . . . . . . . . . . . . . . . 35
Tips for gold prospecting . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Cache Hunting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Recommended mode of operation . . . . . . . . . . . . . . . . . . . . . . . 36
Tips for cache hunting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Common Problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Caring for Your Metal Detector . . . . . . . . . . . . . . . . . . . . . . 39

Bounty Hunter™ metal detectors will detect any item composed all or in
part of metal. Most common and inexpensive metal detectors also detect
metal, but have three important limitations: discrimination, depth
detection and ground balancing. Bounty Hunter™ metal detectors, on
the other hand, possess superior discrimination, depth detection and
ground balancing capabilities.
Metal Types
•iron—a low-grade metal; iron objects range from nails and bolts to
valuable historical relics such as bullets, cannon balls, guns or
shackles.
•aluminum—a low-grade metal; aluminum objects such as foil or
cans are usually undesirable.
•zinc—a lower-grade metal; zinc is found in U.S. pennies minted
after 1982 and many newer, non-US coins also contain zinc.
•copper—a medium-grade metal; copper is found in U.S. pennies
minted before 1982.
•gold—a high-grade metal; jewelry or gold nuggets are gold items
sought by detectorists.
•silver—a high grade metal; jewelry or silver coins are silver items
sought by detectorists.
Discrimination
Discrimination is the detector’s ability to identify the type of buried
metal or completely eliminate unwanted metals from detection.
Bounty Hunter™ Metal Detectors all have superior discrimination
capabilities, allowing them to differentiate between and identify
different types of metals.
Example: If you are searching for valuable coins in a park or beach,
you do not want to dig up pull tabs and cans. You canadjust
the Bounty Hunter™ detector so that it will emit a distinct
tone, or completely tune out these unwanted items so that
you spend your valuable time digging up only valuable coins.
The Basics of Metal Detecting
1

2
Depth Detection
Depth detection refers to the detector’s ability to detect objects at various
depths. The level of depth at which a detector can detect an object
depends on the size of the object—the larger the object, the deeper it can
be detected. Bounty Hunter™ metal detectors provide excellent depth
detection through solid objects. The maximum depth detection capability
of a Bounty Hunter™ Time Ranger™ is five feet. Maximum depth is only
possible for large metal objects.
Example: A quarter can usually be detected from seven to ten inches
deep. A quarter which has been buried for many years may
be slightly oxidized causing the surrounding soil to contain
oxidized metal. In this case, the quarter can develop a “halo”
metallic signature that increases the effective size of the
object, allowing its detection at a deeper depth. We have
many testimonials from users finding coins more than one
foot deep.
Ground Balancing
Ground balancing refers to a detector’s ability to measure and average the
soil’s mineralization. Most soils contain naturally occurring minerals. Some
soils are more highly mineralized than others, and soil mineralization can
vary dramatically within an area from one spot to another. Bounty
Hunter™ metal detectors have patented technology which “sees through”
the earth’s naturally occurring minerals, constantly “measuring” the soil’s
mineralization under its search coil and then “averaging” this measurement.
The result is the soil’s “average mineralization.”
Quick Start
If you want to get started quickly do the following:
1. Assemble detector
2. Install two C-size Alkaline Batteries
3. Hold detector in front of you with coil two feet above the ground
4. Press Power ON/OFF Touch Pad
5. Wait for “ ” to appear under “TARGET”
6. Lower search coil to the ground
7. Press “Disc/Target” Touch Pad
8. You are ready for Motion ALL-METAL detection

Getting Started
Assembly
Assembling your Time Ranger™ is easy and does not require any
tools. Using the following diagram as your guide, just follow these
easy steps.
▲To assemble the Time Ranger™
1. Attach the search coil to the lower stem with knob and bolt supplied.
2. Press the button on the upper end of the lower stem and slide the
lower stem into the upper stem.
3. With your arm relaxed at your side and the search coil level to and
about one inch above the ground, adjust the stem to a length that lets
you maintain a comfortable upright posture.
4. Wind the search coil cable around the stem, leaving enough slack in
the cable to let you adjust the coil when you are hunting on uneven
ground.
TIP:
To adjust the coil, simply loosen the knob.
5. Insert the coil’s plug into the matching connector on the control
housing, making sure that the holes and pins line up correctly.
CAUTION:
Do not force the plug or you might damage it.
To disconnect the cable, pull out the plug—do not pull on the
cable.
3
Bolt
Knurled
Knob
Search
Coil
Cable
Upper
Stem
Control
Housing
Plug
Lower
Stem
Lower
Stem
Upper
Stem
Connector
on back of
control housing

4
Batteries
Your Time Ranger™ metal detector requires two C ALKALINE batteries.
Using the following diagram as your guide, follow these easy steps to
install the batteries.
▲To install the batteries
1. To remove the battery compartment cover, carefully press the release
clip to the right of the cover.
2. Pull out the battery holder and install two C batteries.
3. Slide the battery holder back into the battery compartment.
4. To replace the cover, carefully insert the side opposite the release clip
first and then carefully press down on the other side until the cover
snaps in place.
CAUTION:
Use only fresh batteries of the required size and type. Batteries
must be ALKALINE type, such as Energizer C size LR14.
▲To check the batteries
1. Turn the unit ON.
The low battery indicator and all other arrow indicators appear
briefly in the LCD display, indicating that the detector is working
properly and the batteries are good.
2. If the arrow on the BATT (battery) dial points to R(Replace), replace
the batteries.
NOTE:
Many metal detector problems are caused by weak, dead, or
improperly connected batteries. If the detector does not turn on,
or if it shows signs of weak volume, improper tuning, erratic
operation, or drifting, replace the batteries.
Release
Clip
Release Clip of
Battery Door C Size Alkaline
Batteries

TIP:
You can extend battery life by using headphones. The Time
Ranger™ is equipped with a headphone jack for use with any
1/4” stereo-type headset.
Turn the unit OFF when not in use, and if you do not plan to use
the detector for a week or more, remove the batteries.
For optimum performance, replace the batteries when the BATT
indicator on the LCD display indicates L(Low).
Headphones
The Time Ranger™ is equipped with a stereo headphone jack. Using
headphones (not supplied) with your metal detector not only extends
battery life, but also makes it easier to identify subtle changes in the
threshold levels for better detection results.
▲To connect and use headphones
1. Insert the headphone 1/4” plug into the headphone jack on the
underside of the control panel, as shown in the following diagram.
2. Set the headphone volume to the lowest setting before you begin
listening; after you begin listening, adjust each volume control to a
comfortable level.
5
Headphone
Jack
1/4 inch
Headphone
Plug
SNIFF
ALL METAL
SMART
TRAC
PRESET DISC
TARGET
POWER
ON/OFF
BLANKER

6
Listening Safety
•Do not listen at extremely high volume levels—extended high-volume
listening can lead to permanent hearing loss.
•Once you set the volume controls, do not increase them. Over time,
your ears adapt to the set volume level, so a volume level that may not
necessarily cause discomfort might still damage your hearing.
Traffic Safety
Do not wear headphones while operating your detector in traffic areas.
This practice could create a traffic hazard and is illegal in some areas.
While your headphones are designed to let you hear some outside
sounds at normal volume levels, they still present a traffic hazard.

7
The control panel, as shown in the following diagram, is located at the
center of the control housing. It consists of an LCD display, probable
target ID fields, and several touch pads. The control panel provides
control and constant reference during all detector operations.
Combined with its 3-Tone Audio Target Identification, the Time
Ranger’s control panel provides as accurate a reference as possible
while detecting in the field.
Probable Target ID fields
The Probable Target ID fields, located at the top of the control panel,
represent various coin and metal types as well as a GOLD RANGE and
SILVER RANGE. The coin types can also signal other types of metals
or objects that are within a similar detection range. When the Time
Ranger™ senses a target, an arrow on the LCD display points to the
probable target on the Probable Target ID fields. Until the unit detects
another object, the arrow remains pointing to the most recently detected
object type. The following table lists the probable target IDs along with a
brief description of each.
Control Panel
SNIFF
ALL METAL
SMART
TRAC
PRESET DISC
TARGET
POWER
ON/OFF
BLANKER

8
PROBABLE TARGET ID Fields
Probable Target
ID
GOLD RANGE
SILVER RANGE
IRON / FOIL Indicates that the target is probably iron or foil. Time Ranger™
has four levels of progressive iron discrimination—from small
to large. Some rusted oxidized iron may occasionally register in
the SILVER RANGE.
5¢
Located on the top portion of the control panel. The GOLD
RANGE is located on the left and the SILVER RANGE is on
the right. Other metal types can appear in this range: for
example, iron, foil and nickel appear under GOLD RANGE
and copper pennies appear under SILVER RANGE.
Description
Indicates that the target is possibly a nickel. Many gold rings
register as 5¢. A percentage of foil and many newer pull-tabs
are still detected as nickels.
Indicates that the object is probably a pull-tab. Some small
gold may also register as a pull tab.
Indicates that the target is probably a zinc penny (post 1982) or
a screw cap. This target ID is usually accompanied by a
medium tone. Other targets, such as large gold, may also
register in this field.
Indicates that the target is out of identification range.
These four fields indicate a coin type or an object or metal
within similar detection range. Many other objects are
identified in this range: for example, copper, brass and
oxidized metals such as cans, jewelry, tokens, medals, or
even junk metal objects that fall in the same range.
PULL TAB
Z-1¢
S-CAP
DEEP TARGET
1¢
10¢
25¢
50¢
$1

9
Dectector Touch pads
POWER ON/OFF is used to turn the detector on.
ALL METAL SMART TRAC is used to select the ALL
METAL mode of operation.
SNIFF isused to enable the SNIFF mode of operation.
BLANKER is used to enable the unit’s BLANKER
feature.
DISC TARGET is used to select DISCRIMINATION
mode and to “lock in” programmed settings.
PRESET is used to select preset targets in
DISCRIMINATION mode.
ACCEPT and REJECT are used to select customized
or PRESET targets in DISCRIMINATION mode and
to accept or reject targets in SNIFF mode.
Touch pads
The detector control panel includes several touch pads as shown
and described in the following table. These touch pads are used to
set detector operation.
SNIFF
ALL METAL
SMART
TRAC
PRESET DISC
TARGET
POWER
ON/OFF
BLANKER
POWER
ON/OFF
ALL METAL
SMART
TRAC
BLANKER
DISC
TARGET
PRESET
SNIFF

10
TARGET Readout
TARGET Meaning Description
Ac Accept Appears when you press + using the +/-
TARGET touch pads. Indicates that the
target has been accepted.
LCD Display
The LCD display consists of the TARGET readout and both adjustment
and indicator dials. Arrows also appear at the top of the LCD display,
pointing to the probable target detected in the Probable Target ID fields.
▲TARGET Readout
The TARGET readout displays general detector operating information. It
appears in the top center of the LCD display between the SENSITIVITY
and DEPTH dials. The following table lists the general operating
abbreviations that appear under TARGET, their meaning, and a brief
description of each.
Touch pads (continued)
LOW and HIGH are used to adjust the detector’s
sensitivity in DISCRIMINATION mode. LOW and
HIGH are used to adjust the detector’s AUDIO
LEVEL in ALL METAL mode.
gb Ground
Balance Indicates the unit has taken ground measurements and averaged them.
rY Discriminate Mode Mode Indicates the detector is ready for
operation in ALL METAL mode.
288 ID Numbers
0-299 Indicate air and ground measurements and target value range for more detailed
target identification.
Ar Air Value Indicates the detector is testing the air.

TARGET Readout
TARGET Meaning Description
IR Discrimination Indicates the detector is ready for selective
target discrimination adjustment in the
DISCRIMINATION mode.
IR 1 Iron Mass Level 1 Indicates rejection of small iron objects.
IR 2 Iron Mass Level 2 Indicates rejection of small to medium
iron objects.
IR 3 Iron Mass Level 3 Indicates rejection of medium to large
iron objects.
Fo Foil Indicates object is composed of aluminum foil.
IR 4 Iron Mass Level 4 Indicates rejection of all iron objects.
11
rE Reject Appears when you press the REJECT (-)
TARGET touch pad. Indicates that the
target has been rejected.
SNIFF SNIFF Mode Appears when you press the SNIFF
touch pad and indicates that the unit is
operating in SNIFF mode.
TARGET Readout
Value Range Objects
32-41 Nickel
51-56 $5 Gold Piece
35-60 Ring Pull-Tab
62-90 Beavertail Pull-Tab
99-104 Zinc Penny
115-145 Wheat Cent
141-149 Clad Dime
150-163 Mercury Dime
183-197 Clad Quarter
190-202 Silver Quarter
187-197 Clad Dollar
224-238 Franklin Half Dollar
239-255 Silver Dollar
293-299 Rusty Hinge
The table below list some common target value equivalents. With experience in
the field, you will recognize many types of metals by their numeric value.

SENSITIVITY
The SENSITIVITY dial is located on the top left of the LCD display and is
used in conjunction with the LOW (-) or HIGH (+) touch pads to adjust
the Time Rangers™ sensitivity while operating in DISCRIMINATION
mode. The arrow points to the selected setting. Adjust sensitivity to
eliminate electromagnetic interference or to adjust detector depth.
DEPTH
The DEPTH dial is located on the top right of the LCD display and
indicates the depth of the detected target in a range of 2-10 inches. The
arrow points to the detected depth. When the depth exceeds 10 inches,
an arrow appears under DEEP TARGET in the PROBABLE TARGET ID
fields. Depth detection is usually accurate to eight inches or less for
coin-sized objects only.
BATT
The BATT dial is located on the bottom left of the LCD display and
indicates battery strength as follows:
G=Good
F=Fair
L=Low
R=Replace
12
▲Dials
The LCD display has five indicator/adjustment dials, as shown in the
following diagram. All are used to monitor the detector’s operation; the
SENSITIVITY dial is used in conjunction with touch pads on the control
panel to adjust the detector’s sensitivity and the BLANKER dial is used
in conjunction with the BLANKER touch pad to set the level at which
the detector will eliminate surface objects.

GROUND MONITOR
The GROUND MONITOR dial indicates whether the detector has
achieved ground balance in all soil conditions while operating in
ALL METAL mode.
BLANKER
The BLANKER dial, located on the bottom right of the LCD display,
is used in conjunction with the BLANKER touch pad to set the level
at which to eliminate surface targets as follows:
2 = 2 inches
O = Off
4 = 4 inches
13

Basic Operation
Turning the Detector ON
Follow these steps to turn on your Time Ranger™ detector.
1. Hold the detector with the search coil about waist high and press
the POWER ON/OFF touch pad.
The unit emits three beeps and Ar appears momentarily in the
TARGET readout, indicating that the detector is measuring the air.
2. When IR appears in the TARGET readout, lower the detector to the
ground and select from one of two Time Ranger™ modes of operation:
◆ALL METAL—This mode is used to detect all metals without motion.
In this mode, metals are identified by volume increases in only one
continuous medium tone.
◆DISCRIMINATION—This is a motion mode that allows you to
eliminate undesirable objects from detection. In this mode, metals
are identified via the LCD display and with three distinct tones. By
pressing the Disc Touch Pad after IR appears, you automatically
enter motion All Metal Mode; no metals are rejected.
DISCRIMINATION Mode
In DISCRIMINATION mode, you can accept all targets, select PRESET
targets, or program your own combination of targets to accept or reject,
operate the unit in SNIFF mode, or use the BLANKER feature. In this
mode, the detector must be in motion to detect targets.
▲To accept all targets
1. Perform the steps described in Turning the Detector ON section of
this manual.
SNIFF
ALL METAL
SMART
TRAC
PRESET DISC
TARGET
POWER
ON/OFF
BLANKER
14

2. Press the DISC TARGET touch pad to “lock-in” the programming.
The blinking arrow under IRON/FOIL disappears and IR
appears in the TARGET readout (indicating that the detector
is set to accept all metals, including all levels of iron) as
shown in the following diagram.
▲To select PRESET targets
The Time Ranger™ has three PRESET modes:
1. Perform the steps described in Turning the Detector ON section of
this manual.
2. Press the DISC TARGET touch pad.
A blinking arrow appears under IRON/FOIL in the Probable
Target ID fields, meaning the detector is ready for programming.
3. Press the PRESET touch pad once to select PRESET 1.
The blinking arrow under IRON/FOIL is replaced by an R.
4. Press the PRESET touch pad twice to select PRESET 2.
An Rappears under PULL TAB in the Probable Target ID fields.
5. Press the PRESET touch pad three times to select PRESET 3.
An Rappears under Z-1¢/S-CAP in the Probable Target ID fields.
PRESET 1 Rejects all levels of iron and aluminum foil.
PRESET 2 Rejects pull-tabs, iron and all objects rejected in PRESET 1 mode.
PRESET 3 Rejects zinc pennies, screw-caps, pull-tabs, aluminum, other similar
objects, and all objects rejected in PRESET 1 and PRESET 2
modes.
SNIFF
ALL METAL
SMART
TRAC
PRESET DISC
TARGET
POWER
ON/OFF
BLANKER
15

Rappears under the metals excluded by the PRESET
level you selected, as shown in the following example.
Example of Time
Ranger™ set to PRESET
2 (iron/foil and pull tabs
are rejected).
NOTE:
Pressing PRESET a fourth time clears all PRESET settings
and the unit resets to accept all metals.
▲To select customized targets
The Time Ranger™ has a valuable detection feature called Progressive Iron
Discrimination which allows you to set four levels of iron discrimination
based on size. Before you can customize targets, you must first select
the size of iron to eliminate.
Progressive Iron Discrimination Levels
IR 1
IR 2
IR 4
IR 3
Rejects the smallest of iron objects, such as tacks, small screws and
nails, and BB size objects.
Rejects objects up to about twice the size of IR1 type objects.
Rejects mid-size objects such as a pocket knife, but detects larger
objects such as a pistol, cannonball or strongbox.
Rejects all iron objects.
1. Perform the steps described in Turning the Detector ON section of
this manual.
2. Press REJECT once to select IR1.
IR1 appears in the TARGET readout.
3. Press REJECT twice to select IR2
IR2 appears in the TARGET readout.
16
RR

4. Press REJECT three times to select IR3.
IR3 appears in the TARGET readout.
5. Press REJECT four times to select IR4.
IR4 appears in the TARGET readout.
6. Press ACCEPT after your selection to “lock-in” the iron discrimination
level.The level of iron discrimination you selected appears in the
TARGET readout, an Rappears under IRON/FOIL, and the
blinking arrow appears under 5¢ as shown in the following
example.
7. Press REJECT or ACCEPT, depending on whether you want to
accept or reject the 5¢ targets.
NOTE:
Normally, you want to accept the 5¢ targets because many
gold items are detected as such.
The blinking arrow appears under PULL TAB.
8. Depending on how you want to customize your targets, continue
pressing ACCEPT or REJECT as the blinking arrow appears in the
remaining Probable Target ID fields.
TIP:
To accept the remaining targets and “lock-in” your
selection(s), you can press DISC TARGET at any time.
SNIFF
ALL METAL
SMART
TRAC
PRESET DISC
TARGET
POWER
ON/OFF
BLANKER
17
R
➔