Bravat B25827TW-3W User manual

A
PRODUCTS INSTALLATION INSTRUCTIONS
1
Model : B25827TW-3W
Description : 1.8m Air Massage Bathtub
1.Dimensions:
2.Material: Acrylic
3.Innovative 244 intensive airjets, all-encompassing
balancedbody massage experience.
4.Adjustable airflow,free massage intensity setting.
5.BODY-CONTOUR airjet design, aesthetic outline,
comfortableand ideal for lying bath
6.Smart cleaning system, ensure hygienic and healthy
1800×800×730mm
Unit:mm
Only white color available
INSTALLATION DIMENSIONS
7.Full water volume is 230L (up to overflow)

B
HELPFUL TOOLS
CONFIGURATION AND PARAMETERS
Adjustable Wrench Marking Gauge and Pencil Tape Measure Neutral Mildew Resistant
Silicone Sealant
C
D
Level Safety Glasses
POINTS FOR ATTENTION BEFORE INSTALLATION
1.To facilitate transportation and protect product from damage that may occur in delivery,each bathtub is packed in cartons. In order to avoid
quality dispute,please kindly check product before installation. Or Bravat should not be liable for any quality issue raised after installation.
2.Please read the instruction carefully before beginning to install.
3.Please follow steps in the instruction to install this product or may result in costly mistake. Bravat shall not be responsible for any loss from
that mistake.
4.Professional help is required for installation of this product.
5.Shut off power supply before installation.
6.Keep the area around the Air Pump clean and free of debris,to prevent air duct clog of pump and restriction of air flow through Air Pump.
Inspection
(1) Check and ensure all switch and accessories are in good condition.
(2) Check and ensure bathtub surface is free of hit and damage.
(3) Check and ensure pipe connection is firm and compact.
(4) Before starting installation, check and ensure bathtub,all connections and accessorie are free of leaks that may occur during delivery.
Attention points at Installation
(1) To facilitate maintenance and clean, we recommend to install bathtub on finished floor with ceramic tile or terrace with ground tile.
(2) To facilitate install and maintenance bathtub’s key parts like drainage system, control system and air pump, DON’T wall up bathtub
with cement or tiles.
(3) DON’T lift pipes or use pipes as lift when transport bathtub.
(4) DON’T remove bathtub protecting film during installation.
(5) DON’T take bathtub out of package for installation until wall and floor preparation finished.
(6) NO bulbs and open fires are allowed to place in bathtub during installation.
(7) NO stuff like sand, cement or other sundries are allowed to place in bathtub as that would likely damage bathtub surface.
(8) NO solvent like paint or glue are allowed to contact with bathtub.
2
AC220V~AC240V
Load configuration parameters
50HZ
900W
30MA
15mA
12A
＞20MΩ
IPX5
Type of Load
Rated Loading Voltage Rated Loading Frequency Others
Operating Conditions and Properties
Rated voltage
Rated Amperage
Insulation resistance
Rated Frequency
Rated Wattage
Leakage Current
Leakage current protection
Water-Resistant Grade
600W
230V
230V 300W
Heater
Air Pump

Turn the system on, touch the icon to turn on the function of keeping the speed of the air pump; the air pump will run at its maximum
power and the white backlight of the icon will be lit; touch the icon again to turn on the function of regulating the speed of the air pump
and the orange backlight the function of regulating the speed of the air pump and the orange backlight of the icon will be lit; touch the icon
for the third time to turn off the function of air pump, then the backlight of the icon will be turned off. During the process of turning the air pump
on, the function of air pump can be shifted between speed maintaining and regulating, by touching and keeping the icon for one second.
Automatic drainage: Turn the system off, the orange backlight of the air pump icon will be lit by touching and keeping the icon for one
second, the air pump will work at its maximum power for three minutes.
Switch the power on, touch the icon on the panel to turn the system on.Then the orange backlight of the power icon and the white
backlight of the lamp icon will be lit. The light of the nozzle is shining white. Touching the icon again or turning time out, all the functions
and button backlight will be turned off. Operation timing: The default setting time of the system is 20 minutes. The system turns off, by touching
and keeping the icon for one second, the backlight of the air pump icon and lamp icon will be lit simultaneously and the timing will be
cancelled; touch the icon again, the orange backlight will be lit simultaneously, and the timing is set. The settings become valid when you
restart the machine.
E
OPERATION INSTRUCTIONS
Attentions at installation of electrical appliances
(1) Professional help from electrician is required to connect power cord of air pump with reference to standards.
(2) Exclusive power source for bathtub must have protective device of creepage,overload and short circuit installed and checked frequently.
(3) Earth wire must be earthed.
(4) Power source must close to electric motors, NO temporary extended socket is allowed to use.
3
(1) Power On/Off
(2) Backup Heating Function
Turn the system on, touch the icon to start the function of backup heating, then the orange backlight of the icon will be lit; touch
the icon again,the function of backup heating and the backlight of the icon will be turned off.
(3) Air Bubble Massage
(4) Lamp
Turn the system on, touch the icon to turn on the manual function of 12-color lamp conversion. Touch the icon each time, the lamp will be
changed into a different color and the white light of lamp icon will be lit.Touch and keep the icon for one second to turn on the lamp
function of automatic color conversion and the orange backlight of the lamp icon will be lit.
AC_N IN
AC_N IN
GND
3
2
1
4
1
23
4
CONTROLLER WIRING DIAGRAM
INPUT VOLTAGE:
INPUT CURRENT:
MAX POWER:
WATERPROOF:
MODEL:
220-240VAC 50/60Hz
4.35A
1000W
IPX5
BTU2.0
CONTROL FANEL
FUSE
FUSE:
T1AL 250VAC 5 20MM
*
Voltage danger!!!
Heater N
Heater L
TRANSFORMER
RGB lamp N
RGB lamp L
Air pump N
Air pump L
Slgnal control
elzzo
n
bgR
x
oblortn
oc
c
lr
tc
ele
pmalBGR
RGB lamp
3W 8
POWER CABLE
220V-240~
(Optlonal)
N L
G
AC INPUT
220-240VAC 50/60Hz HEATER AIR PUMP
TECHNIQUES AND PARAMETERS ARE SUBJECTTO CHANGE WITHOUT NOTICE
Be use for equipment RGB nozzle
Power On/Off Function Key of Backup Heating
Function Key of Air Pump Function Key of Lighting
Electric Connection Blueprint

F
INSTALLATION STEP
4
Cold Supply
Hot Supply
Please embed supply lines,drainage lines, and power socket according to distance from bathtub rim to finished wall. Power socket should be
located above 20cm from finished floor and close to bathtub motor. (Drainage outlet should be 30mm protruding from finised floor)
Power Socket
mm008
mm0081
Drainage outlet
mm934
Adjust leveling feet to keep top rims at horizon,and ensure all feet firmly seat on floor at the same time.
Installation of drain pipes:Install the drain pipes to the bathtub according to the installation instructions of the drain pipes .The figure below is the
installation illustration recommended by our company for the Drain Pipe P9098N series.

5
Switch off the water drainage,pour water into the bathtub,and then check whether there is water leakage.Make sure that the overflow adapter is
leak-proof.
Bfore installation,please refer to the installation diagram.Lay water pipes on the floor,position the power outlet and hot/cold water inlet pipes.
Please ask a professional plumber to complete the actual construction.
20130718V02
If the drainage through the floor is used,the height of the drain outlet is recommended to be 120 mm above from the drain outlet.
(Drainage through the floor is recommended)
1.Suggest to clean bathtub immediately after drainage complete, as soap, body fat and dirt are easy to be removed at the time before bathtub dry.
2.Suggest to clean bathtub frequently if using in high hard water area,where high calcium content in water would leave yellow spot after dir
tattaching on bathtub surface.
3.Please use soft cloth with neutral cleaner or soap to clean bathtub, and then wipe its surface to dry.
4.No hard stuff or abrasive stuff like cleaning powder are allowed to clean bathtub, as that would corrode, scratch and dull bathtub surface.
5. Do not allow paint, paint remover like chloroform or any strong organic solvent like acetone in contact with any bath surfaces,or bathtub surface
would be softened, melted or crackle.
6. Do not place flaming cigarette on bath or it would burn bathtub surface.
7.NO bulbs and open fires are allowed to place in bathtub lest bathtub surface is damaged.
Suggestion to remove scratch:
(1) If scratch is slight, spray metal polish or car polish on scratch at first,and then use electric polishing machine to resume glossy surface.
(2) If scratch is deep, use 2000# abrasive paper to remove scratch at first, and then use same method as (1) to resume glossy surface.
The products installation instruction is written in accordance with the latest product information,
following the sustainable development strategy of the Company, to improve continually the produce's
specification, performance etc.,subject to change without notice. (The Company reserves the right to
interpret)