Jacuzzi Platinum 2001 User manual

Owner’s Manual
Pinnacle
Triton
Laser
Santina

Table of Contents
ImportantHot TubOwner Safety Information..................................................................
Installation..........................................................................................................................
Operation............................................................................................................................
Maintenance.......................................................................................................................
1
5
5
5
8
8
10
10
10
11
13
15
15
16
18
18
18
18
19
20
20
21
21
22
23
24
25
25
26
26
27
27
28
28
29
30
30
31
31
32
33
InspectionandShipping Claim.............................................................................
PositioningYourHotTub.....................................................................................
Electrical Requirements......................................................................................
ElectricalPrecautions.............................................................................................
OutdoorInstallation..............................................................................................
IndoorInstallation.................................................................................................
Drainage...............................................................................................................
Optional Ozone Generator Installation Instructions.............................................
Preparing the Hot Tub for Filling..........................................................................
OperatingInstructions...........................................................................................
ControlPanel........................................................................................................
ControlPanelOperation.......................................................................................
InitialStart-Up......................................................................................................
Settingthe Timeof Day..........................................................................................
FilterSystem Operation.........................................................................................
ChangingHeating Cycles.......................................................................................
PanelLock...............................................................................................................
TemperatureLock.................................................................................................
UnlockingthePanel.............................................................................................
DisplayMessages....................................................................................................
RemoteController (PinnacleandTriton)...............................................................
RemoteControllerOperation................................................................................
NormalOperation/Whirlpool System.....................................................................
SilentAirInduction................................................................................................
AirBlower..............................................................................................................
WaterRainbow........................................................................................................
SpinningNeck Jets(Pinnacle Only)........................................................................
DiverterValves(TritonOnly)..................................................................................
Stereo/CD(Triton/PinnacleOnly)..........................................................................
Water Quality and Water Chemistry...................................................................
Filtration.................................................................................................................
Water Chemistry.................................................................................................
Disinfecting............................................................................................................
Balancing pH......................................................................................................
Balancing Total Alkalinity....................................................................................
Water Quality Definitions....................................................................................
WaterLevel/Drain................................................................................................

Troubleshooting.................................................................................................................
AlternateUse ofthe Water Rainbow asa FillSpout........................................................
34
34
35
36
36
37
38
38
39
39
40
43
SkimmerBasketMaintenance.............................................................................
FilterMaintenance................................................................................................
FactoryInstalled WoodSkirt.................................................................................
AutomaticFiltration/Maintenance...........................................................................
Winterizing............................................................................................................
HotTubLight.........................................................................................................
CleaningYour HotTub...........................................................................................
CoveringYourHotTub...........................................................................................
RepairstotheAcrylic...............................................................................................
HeadrestPillows......................................................................................................

Important Hot Tub Owner Safety Information
Read and Follow ALL Instructions
Your Jacuzzi Premium spa is constructed to the highest standards and is capable of
providing many years of trouble-free use. However, because heat retentive materials
are utilized to insulate the hot tub for efficient operation, an uncovered hot tub surface
directly exposed to sunlight and high temperatures for an extended period is subject
to permanent damage. Damage caused by exposing the hot tub to this abuse is not
covered by warranty. We recommend that you always keep the hot tub full of water
when it is exposed to direct sunlight and that you keep the Jacuzzi Premium Spas
insulating cover in place at all times when the hot tub is not in use. Read and carefully
follow the requirements for your hot tub’s support base (found in the section titled, “
Locating Your Jacuzzi Premium spa”).
Jacuzzi Premium Spas constantly strives to offer the finest hot tubs available, there-
fore modifications and enhancements may be made which affect the specifications,
illustrations and/or instructions contained herein.
FCC Notice
This equipment has been tested and found to comply with the limits for a Class B Digital
Device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reason-
able protection against harmful interference in a residential installation. This equipment gen-
erates, uses and can radiate radio frequency energy and, if not installed and used in accor-
dance with the instructions, may cause harmful interference to radio communications. How-
ever, there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures: 1) Rearrange or relocate the receiving
antenna. 2) Increase the separation between the equipment and receiver. 3) Connect the
equipment into an outlet on a circuit different from the circuit connected. 4) Consult the dealer
or an experienced radio/TV technician for help. (Changes or modifications not expressly ap-
proved by the party responsible for FCC compliance could void the user’s authority to operate
this equipment.)
Page 1

Important Hot Tub Owner Safety Information
Read and Follow ALL Instructions
Warning-Risk of injury: Children, the elderly, and the infirm should not use the hot tub
unless they are supervised at all times. Infants should not be permitted in the hot tub at water
temperatures over 100 F(38 C).
Hot tub water temperature in excess of 104 F is not recommeded. High water temperatures in
excess of 104 F (40 C) and prolonged periods of use can raise internal body temperature
excessively and impair the body’s ability to regulate its internal temperature.
Pregnant women and people with heart circulatory conditions, or diabetes, should consult
their physicians before using the hot tub at water temperatures over 100 F (38 C).
Limit your initial use of the hot tub to 10-15 minutes. High body temperatures affect people
differently; consult your physician about your safety and comfort before using the hot tub.
If your hot tub product does not have a thermometer, we recommend that you use a medical
(clinical) type of thermometer for an accurate measurement of hot tub water temperatures.
Other types of thermometers, generally available, such as those used for swimming pools are
not sufficiently accurate to determine hot tub water temperature.
Extra care should be taken when using the hot tub and consuming alcoholic beverages.
Alcohol, drugs, or certain medications, such as tranquilizers, affect a person’s ability to with-
stand high temperatures and may produce dangerous effects, including drowning. Persons
using medication should consult with a physician before using a hot tub. The use of alcohol or
drugs can greatly increase the risk of fatal hyperthermia in hot tubs.
Hyperthermia
Prolonged immersion in hot water may induce hyperthermia. A description of the causes,
symptoms, and effects of hyperthermia are as follows: Hyperthermia occurs when the inter-
nal temperature of the body reaches a level several degrees above the normal body tempera-
ture of 98.6 F (37 C). The symptoms of hyperthermia include drowsiness, lethargy, and an
increase in the internal temperature of the body. The effects of hyperthermia include: 1) Un-
awareness of impending hazard; 2) Failure to perceive heat; 3) Failure to recognize the need
to exit the hot tub; 4) Physical inability to exit the hot tub; 5) Fetal damage in pregnant women;
and 6) Unconsciousness and danger of drowning.
Page 2

Important Hot Tub Owner Safety Information
Read and Follow ALL Instructions
Danger-Risk of injury: Do not remove the suction grille! It is a safety device and must always
be in place on the suction fitting to minimize the potential hazard of hair entanglement or body
entrapment.
Keep body, hair, and clothing a minimum of 12 inches away from suction fitting and skimmers
at all times when the hot tub is operating. Hair longer than shoulder length should be secured
close to the head, or a bathing cap should be worn.
Do not operate the hot tub if the suction cover is broken or missing. Contact your Dealer for
replacement cover if broken or missing.
The wet surface of the hot tub is slippery. Use care when entering or exiting.
Danger-Risk of child drowning: Do not permit children to use this product unless they are
closely supervised. The use of a locked cover is highly recommended to prevent unattended
access.
DANGER-RISK OF ELECTRICAL SHOCK: Wheninstallingandoperating thiselectricalequip-
ment, basic safety precautions should always be adhered to.
Warning: A wire connector is provided at the electrical cabinet on this hot tub to connect a
minimum No. 8 AWG (8.4mm) solid copper conductor between this hot tub and any metal
equipment, metal enclosures of electrical equipment, metal water pipe, or conduit within 5
feet (1.5m) of the hot tub.
Do not use electrically connected devices such as televisions, radios, stereo speakers, lights,
cooking devices, or telephones within 5 feet (1.5m) of the hot tub while the hot tub is being
used. Lighting fixtures must not be located directly above or within 5 feet (1.5m) of the hot tub.
If located within 10 feet (3.0m) of the hot tub, they must be on a circuit protected by a GFCI
(Ground Fault Circuit Interrupter).
All fixed metal objects located within 5 feet (1.5m) of the hot tub, such as fence posts, railings,
door frames, greenhouse structures, gutters, etc., must be attached to the bonding bar on the
outside of the hot tub electrical cabinet using #8 solid copper wire. With #8 solid copper
wire, bond the hot tub to the house electrical panel or approved local bond.
Page 3

Important Hot Tub Owner Safety Information
Read and Follow ALL Instructions
The spa must be installed with adequate access and water drainage system (refer to Installa-
tion), to drain water away from electrical components.
CAUTION: Do not turn power ON to the hot tub unless it is filled with water to the normal
water level, which is to the water level indicator mark on the skimmer frame. Activating the hot
tub when there is an insufficient amount of water can damage the circulation pump and may
cause a fire.
Hot tubs installed in a 230VAC circuit:
DANGER-RISK OF ELECTRICAL SHOCK
Your hot tub must be equipped with a GFCI at the Main Electrical Panel. At initial start-up
and before each use thereafter with power ON, push the GFCI test button. The reset
button should pop out. Push this button in to reset. If the interrupter fails to operate in this
manner, there is a ground current flowing or a device malfunctioning, indicating the possi-
bility of electrical shock. Turn off power and do not use the hot tub until the source of
the breakdown has been identified and corrected.
Read manufacturer’s safety information provided with all optional equipment.
Page 4

Installation
Inspection and Shipping Claim
Check for shipping damage upon receipt of the hot tub. Jacuzzi Premium Spas is not
responsible for damage to the hot tub sustained during shipment. If damage is evident before
unpacking, refer to instructions regarding shipping claims on the outside of the carton and
immediately file a claim with the carrier.
Once the hot tub has been removed from the carton and before it is permanently installed,
check the hot tub completely for damage. Fill the shell with water and operate the system
(refer to Operating Instructions) to check for leaks which may have resulted from improper
shippingor handling.AllJacuzzi PremiumSpas hottubsare factorytested forproperoperation
and water tight connections prior to shipment. If leaks or other problems are detected,
immediatelynotifyyour JacuzziPremiumspa dealer orAuthorized Service AgentforWarranty
Service.
NOTE: Damage or defects which could have been discovered and repaired prior to
installation and which are claimed after final installation of the hot tub, are excluded
from our warranty.
Positioning Your Hot Tub
IMPORTANT: Because of the combined weight of the hot tub, water and users, it is extremely
important that the base upon which the hot tub rests be smooth, flat, level and capable of
uniformly supporting this weight, without shifting or settling, for the entire time the hot tub is in
place. If the hot tub is placed on a surface which does not meet these requirements, damage
to the skirt and/or the hot tub shell may result. Damage caused by improper support is not
covered under warranty. It is the responsibility of the hot tub owner to assure the integrity of
the support over time.
Page 5

Installation
Page 6
Wood decking is acceptable provided it is constructed so that it meets the requirements
outlined on the previous page. However, we recommend a poured, reinforced concrete slab
(minimum 4 inches thick) as shown below.
Start with the forms built from 2X4’s and 1X2 stakes as shown above. The foundation must be
as large as the bottom of the hot tub. Dig down 2 inches below the bottom of the forms and fill
back to the bottom of the forms with clean sand. It is recommended that you lay a 1-foot-
square grid of 1/2” reinforcing rods over the level sand bed, tying them together with bailing
wire. Mix concrete and pour it into the form, spreading it evenly with a sturdy steel rake. Level
concrete with a screed built from 1X4’s as shown above. Pull the screed toward you with a
side-topside zigzag motion. When concrete is leveled, smooth out with a large mason’s float.
Allow concrete to cure at least one week before setting tub.
Screed

Installation
Page 7
The hot tub must be installed in such a manner as to provide drainage away from the hot tub.
Placing the hot tub in a depresion without provisions for proper drainage could allow rain,
overflow and other casual water to flood the equipment and create a wet condition in which it
would sit.
For hot tubs which will be recessed into a floor or deck, install so as to permit access to the
equipment,eitherfromaboveorbelow,forservicing.Makecertainthat thereare noobstructions
which would prevent removel of the cabinet side panels, especially on the side with the
equipment bay doors.
In selecting the ideal outdoor location for your hot tub, we suggest that you take into
consideration 1) the proximity to change area and shelter (especially in colder weather); 2)
the pathway to and from your hot tub (this should be free of debris so that dirt and leaves are
not easily tracked into the hot tub); 3) the closeness to trees and shrubbery (remember that
leaves and birds could create extra work in keeping the hot tub clean); 4) a sheltered
environment(lesswindandweatherexposurecan resultin loweredoperationandmaintenance
costs); and 5) the overall enhancement of your environment. It is preferable not to place the
hot tub under an unguttered roof overhang since run-off water will shorten the life expectancy
of the hot tub cover.
For indoor installations, be certain to make provisions for proper ventilation. When the hot tub
is in use, considerable amounts of moisture will escape. This can damage certain surfaces
over time.
If you have any questions regarding the placement or installation of your hot tub, consult your
authorized Jacuzzi Premium Spas dealer or service organization.

Installation
Electrical Requirements
Your Jacuzzi Premium spa (except the Triton) requires a 230VAC, 50 AMP, 4-wire grounded
type GFCI protected electrical service with copper conductors, and must be in a separate
circuit having no other appliance connected in that circuit. If you do not have this kind of
circuit, a qualified electrician should install the necessary wiring. A wiring diagram is provided
on the inside cover of the electrical control box. Inadequately sized wiring may cause the unit
to malfunction and bring about permanent damage to the hot tub’s electrical system. The
circuit must also have a ground wire in order to take advantage of the designed-in safety
featuresof the hottub. Abondwire mustalsobe used.Bond accordingtoprocedure described
below.
WARNING: Without proper grounding and bonding, a system malfunction may cause
fatal shock.
Electrical Precautions
CAUTION: Do NOT apply electrical power to the hot tub unless it is filled with water to the
normal water level, which is approximately 7” below the hot tub rim (refer to location of water
level indicator on the face of skimmer). If the hot tub’s motor/pump(s) are actuated when
there is not sufficient water in the unit, the circulation pump could be irreparably damaged.
Not heeding this caution will nulify the warranty. In addition to damaging the unit, operating
the unit with insufficient water could cause a fire.
Do NOT locate lighting fixtures directly above the hot tub; lighting and electrical receptacles
must be located at least 5 feet from the hot tub. Lighting located between 5 and 10 feet from
the hot tub must be on a circuit protected by a GFCI. (Refer to National Electrical Code, 680-
6.)
Do NOT use electrically connected devices, such as televisions, radio, telephones, stereo
speakers, light or cooking devices within 5 feet of the hot tub when the hot tub is being used.
All fixed metal objects located within 5 feet of the hot tub, such as fence posts, railings, door
frames, greenhouse structures, gutters, etc., must be attached to the bonding bar on the
outside of the hot tub electrical cabinet using #8 solid copper wire. With #8 solid copper
wire, bond the hot tub to the house electrical panel or approved local bond.
An approved ground may be an 8 foot long ground rod, a plate electrode, or a buried metal
waterpipewith atleast10 feet ofburied pipe. Checkyourlocal buildingcodefor requirements.
Bonding lugs are available at your local electrical supply store. (Bond bar location is shown on
the next page.)
Page 8

Page 9
Installation
Equipment Area
1. Electrical Cabinet
2. Power Supply Entrance
3. Pump
4. Heater
5. Hot Tub Drain
6. Air Blower
7. Pump Drain Plugs
8. Pump #2
9. Circulation Pump
Electrical Cabinet
BLACK
WHITE RED
1 2 3 4
5GREEN
50A 20A
J8
CIRCUIT
BOARD
Terminal Block
BLACK
WHITE RED
1 2 3 4
5GREEN
1
2
3
4
5
6
77
8
9
innacle)

Installation
Outdoor Installation
If you install the hot tub outdoors, we recommend that you provide a concrete pad for it to rest
on. To do this, see instructions for constructing a concrete pad on page 6.
Indoor Installation
Water that splashes on the floor during hot tub use may cause a walking hazard and/or
structuraldamage.Gooddrainage must be provided and properwaterproofbuilding materials
must be used in the area surrounding and beneath the hot tub. Take into consideration that
high room humidity will exist due to high spa water temperatures. Providing natural or forced
ventilationof theroom willhelp maintaincomfort andminimize moisturedamage tothe building.
Jacuzzi Premium Spas is not responsible for damages resulting from excess moisture or
water spillage. Consult an architect or engineer for aid in designing your indoor installation.
Drainage
Whether you install your hot tub indoors or outdoors, you can drain it completely by attaching
a garden hose to the fill and drain valve located on the pan of the hot tub. Simply run the hose
to the house sewer line or drain field and open the drain valve.
Make sure the area surrounding the hot tub has good drainage to keep water from collecting
at the base of the hot tub-especially near the equipment area. If drainage is poor, install a
drain line and/or gravel drain field.
Page 10

Installation
Optional Ozone Generator Installation Instructions
Your“ozoneready” hottub is designedfor easyfieldconversion toanozone generatorsystem.
You will need:
A. Complete Ozone Kit
and
B. Mazzei Injector
Instructions:
1. Turn OFF electrical power and drain the hot tub.
2. Temporarily remove the equipment access skirt panel and other skirt panels as required for
access to the plumbing.
3. Cut off and discard the PVC caps at the end of each length of flexible vinyl tubing as shown
in Figure 1.
4. Insert Injector fitting into flexible vinyl tubing and secure with hose clamps (2). Do NOT
change the length of the flexible vinyl tubing downstream of the red ozone injector. Observe
the“properorientation”ofthe ozoneinjector;makesurethe molded-inarrowpointsdownstream
to the footwell fitting. See Figure 2.
Page 11
(Some items not shown for clarity)
FIGURE 1 - "OZONE-READY" SPA BEFORE CONVERSION (SKIRTS REMOVED)
3/4" VINYL TUBING
WITH CAPPED END
(CUT OFF CAP) FROM DISCHARGE
MANIFOLD OR
PUMP DISCHARGE
TO FOOTWELL FITTING
FIGURE 2 - OZONE INJECTOR LINE CONVERSION
FROM
DISCHARGE
(NOTE: Flow arrow on injector points downstream to footwell.)
TO
FOOTWELL
FITTING
IN-LINE DETAILS
HOSE CLAMPS
6540-202
MAZZEI

Installation
5. Install the ozone generator according to the manufacturer’s instructions. Several
commercially available ozone generators will fit easily.
6. Attach the ozone delivery tubing (supplied with the ozone generator) between the ozone
generator outlet port and the ozone injector inlet. Form the extra length of tubing into two or
more loops 6”-12” in diameter. Find the bonded clip underneath the hot tub rim near the
control panel area and secure the loops in a maximum height position by attaching the loops
with a tie wrap strap to this clip.
NOTE: If the ozone generator or ozone tubing includes a check valve, make certain it is
correctly oriented and correctly functioning before installation. The check valve should permit
ozone gas flow from the ozone generator to the ozone injector. See Figure 4.
7. Refill the hot tub with water to the fill mark on the skimmer frame. Check for leaks.
8. Plug the ozone generator power cord into the socket labeled “ozone” on the side of the hot
tub electrical cabinet.
9. Turn on the circuit breaker for power to the hot tub system. Test the GFCI for proper
operation.
10. Operate the hot tub and recheck for leaks.
11. Reinstall the plumbing access skirt panels and equipment access skirt panel.
Page 12
FIGURE 3 - MOUNTING BOARD
USE #6 SCREWS
OZONE GENERATOR
MOUNTING BOARD
ELECTRICAL
CABINET
FIGURE 4 - OZONE GENERATOR VINYLTUBING
(NOTE: VERIFY ORIENTATION
OF CHECK VALVES)
ELECTRICAL
CABINET
OZONE
GENERATOR
POWER PLUG
CONNECTION
VINYL TUBE FROM
GENERATOR
INJECTOR
INLET TO OZONE
GENERATOR

Page 13
Installation
Preparing the Hot Tub for Filling
1. Remove the plastic sheet covering the spa.
NOTE: Stepping into the hot tub with shoes will scratch the acrylic surface.
2. Remove any packing materials from the hot tub.
3.The filtercartridgesare packagedin aplasticbag whichMUST be removedbefore operating
the hot tub. To gain access to the filters, pull open the skimmer/filter door by the handle
located in the middle of the door and remove the skimmer basket and filter.
Front Access Skimmer/Filter
SKIMMER BASKET
WEIRDOOR
FILTER CARTRIDGE
ROPE LOOP
4. Clean the interior of the hot tub of any remaining construction debris. Remove stubborn
stains, paint, or tar with isopropyl alchohol. A mild liquid dishwashing detergent on a damp
cloth is fine for cleaning off other dirt. Plaster can be removed by scraping with a soft plastic
or wooden edge. Do not use a metal scraper, wire brush, or other metal tools, as they will
damage the hot tub’s surface.

Installation
5. On initial start-up, it is recommended to purge and sanitize the system as stated below.
- Remove the hot tub cover completely.
- Close the drain valve on the suction plumbing.
- Fill the hot tub with water through the filler housing to its normal level, which is to the
water level indicator mark on the skimmer frame.
- Turn ON the circuit breakers at the main electrical panel.
- At the control panel on the hot tub rim, press the JETS button twice for maximum jet
action.
- Add 1/2 cup sodium dichlor (a fast dissolving granular type of chlorine) to the water and
run for 30 minutes.
- Turn OFF the circuit breakers.
-Immediately open the drain valve and drain the hot tub completely.
CAUTION: Leave the optional cover OFF the hot tub during this procedure. DO
NOT use the hot tub during this procedure. Drain the hot tub immediately
afterword.
6. Close the drain valve and fill the hot tub with water (approximately 7 inches below the hot
tub rim) to the water line indicator on the skimmer frame.
7. Turn ON circuit breakers at the main panel.
8. Test the hot tub for proper operation. (Refer to Operating Instructions.)
9. Add 4 tablespoons of chlorine to the water.
10. Refer to Water Quality section of the Operating Instructions. Test for water quality and
then add treatment chemicals as necessary to ensure proper water quality levels.
All Jacuzzi Premium spas are factory tested for proper operation and water tight connections
prior to shipment. If leaks or other malfunctions are detected, immediately notify your Jacuzzi
Premium Spas dealer or Authorized Service Agent.
Page 14
NOTE: Never fill with water from a water softener. If your water is extremely “hard”, it is
preferable to fill it half way with hard water and the rest of the way with softened water.
Or, you may fill entirely with hard water if you use a special water additive available
from your Jacuzzi Premium Spas dealer or service organization.

Page 15
Operation
Operating Instructions
Now that the hot tub is in place, you are probably eager to take advantage of its unique
designed-in features - especially the patented hydromassage performance. Besides being a
beautiful addition to your indoor decor or outdoor landscaping, your Jacuzzi Premium spa will
provide you with the ultimate in hot tub pleasure.
Familiarize yourself with the operation of the electronic control pad, as described on the
following pages of this manual. Access under the hot tub (behind the skirts) is not required for
normal operation.
WARNING: Do not turn ON power to the hot tub unless it is filled with water to the
normal water level. Refer to the water line indicator mark on the skimmer frame.
Whenever the power is ON, the system will activate even though no controls are
operated. When there is not sufficient water in the unit with the hot tub’s motor/pump
actuated, the circulation pump and heater could be irreparably damaged. Not heeding
this caution will nullify the warranty. In addition to damaging the unit, operating the hot
tub with insufficient water could cause a fire.
Initial Instructions
UsingaGardenhose, fill the hot tub withwaterto the water line indicator markontheskimmer
frame.
At the house service panel, turn ON the circuit breaker or switch that controls the electrical
service to your hot tub. Make sure there are no other appliances on that circuit.
Electrical
Your hot tub must be installed in an electrical circuit protected with a Ground Fault Circuit
Interrupter (GFCI)(refer to Electrical Requirements). At initial start-up and before each use
thereafter, with power ON, push the GFCI test button. The reset button should pop out. Push
this button in to reset. If the interrupter fails to operate in this manner, there is a ground
current flowing or a device malfunctioning, indicating the possibility of electrical shock.
DANGER: Turn OFF power and do not use the hot tub until the source of the problem
has been identified and corrected.

I0IF
HEAT
STANDARD
FILTER 1
P
l
a
t
i
n
u
m
S
E
R
I
E
S
Operation
Control Panel
The control panel is easy to use with fingertip control of all the hot tub’s functions.
Temperature Control
When either of these buttons is pressed once, the display will show the temperature that has
been set, in addition to the words SET HEAT. Each time either of these buttons is pressed
again, the set temperature will increase or decrease in increments of 1 F depending on which
button is pressed. After three seconds of inactivity, the display will automatically show the
current hot tub water temperature.
Page 16
Jets Control
Press this button once to activate a jet pump on one side of the hot tub; press it twice for both
pumps to operate simultaneously for maximum effect. Press it a third time to turn off the jet
pumps. This button does not affect the filter pump operation which is an independent function.
When the jet action mode is started with this button, it will automatically stop after 30 minutes
of operation.
Blower Control
Starts or stops the blower for aeration in the hot tub. Blower operates in all functions. The
blower will also automatically stop after 30 minutes of operation.