Bravat F11379C-ENG User manual

180
167
MAX25
MAX450
MAX190
2-G1/2-14
MAX50
136
5°
50
35
54
45
32
MODEL: F11379C-ENG
Description: Single Handle Lavatory Faucet
PRODUCTS INSTALLATION INSTRUCTIONS
A
INSTALLATION DIMENSION
Unit:mm
F
MAINTENANCE
CAUTION: Always turn water OFF before removing existing or disassembing the faucet. Open faucet handles to relieve water
pressure and insure that complete water shut-off has been accomplished.
To keep the surface clean and bright, please clean the faucet regularly,please abide by the following
procedures:
1. Use rinsing water and soft cloth, clean bilge and bilge membrane on the surface to the best of the abilities.
2. Cleaned the residua with the following cleansers only.
3. After cleaning, use rinsing water to clean all cleanser immediately and drying with a soft cotton cloth.
4. Carefully dismantle the aerator regularly, rinse under clean running water until any loose debris is cleared to avoid
the influence to water outflow.
Soft liquid cleanser.
Colorless glass cleanser, totally soluble powder cleanser without abrasive capability.(Mixed by instructions.)
No abrasive cleansers waxes.
Never use cleanser, emery cloth or handkerchief which can rub.
Never use cleaners containing abrasive cleansers, ammonia,bleach, acids, waxes, alcohol, solvents or other
products not recommended for chrome.
G
SPECIAL STATEMENT
The products installation instruction is written in accordance with the latest product information, following the sustainable development
strategy of the Company, to improve continually the produce's specification, performance etc.,subject to change without notice. (The
Company reserves the right to interpret)
115121632
415121632 Designed and developed by Bravat/Dietsche Germany
Designed and developed by Bravat/Dietsche Germany
NO. NAME QTY.
1 Set Screw M5X5 1
2 Plug 1
3 Handle 1
4 Dome 1
5 Nut M45*1.5 1
6 Cartridge 1
7 O-Ring D37XD2 1
8 Sleeve 1
9 Body 1
10 Lift Rod 1
11 Lift Knob 1
12 Washer D36XD45X1.5 1
13 Plug M8X90 1
14 Rubber Washer 1
15 Washer 1
16 Screw 1
17 Braided Hose 2
18 PUP-UP Installation 1
19 Allen Key 2.5mm 1
20 Aerator Housing 1
21 O-Ring D24XD2 1
22 Aerator 1

B
HELPFUL TOOLS
Before installing the new mixer, it is essential that you thoroughly flush through the supply pipes in order to remove any remaining swarf,
solder or other impurities. Failure to carry out this simple procedure could cause problems or damage to the workings of the mixer.
Work water pressure: 0.5-5kgf/cm² (Including cold and hot).
If the pictures and statements in the ‘Installation Specifications’ is unconfirmed with practicality, please take practicality as standard.
！Points for attention before installation
INSTALLATION STEP
C
FAUCET OPERATION
D
SPECIFICATION
E
Application:
Operation with unpressurized storage heaters is not possible.
Specifications
If static pressure exceeds 5 bar, a pressure-reducing valve
must be fitted.
Avoid major pressure differences between hot and cold water
supply.
GB
This technical product information is exclusively
for the installer or trained specialists.
Please pass these instructionson to the user.
min. 0.5 bar – recommended 1 – 5 bar
rab01.xam:erusserpgnitarepO
rab61:erusserptseT
Flow rate at 3 bar flow pressure
nim/l5,12.xorppa:htabrof
nim/l81.xorppa:rewohsrof
C°08.xamerutarepmettelniretawtoH
Recommended (energ C°06:)gnivasy
Installation:
Flush piping system prior and after installation of
fitting thoroughly (Consider EN 806)!
Fitting a temperature limiter is possible
The projectioncan be increased by 20mm,
extension
Function:
Check connections for leaks and check function of
fitting.
Flow is diverted automatically from shower outlet to
bath inlet when the fitting is closed.
Maintenance:
Inspect and clean all components and replace if
necessary.
Shut off water supply for maintenance work.
When installing the cartridge, ensure that the
seals are correctly seated.
Tighten the screws evenly and alternately.
Replacement parts: see exploded drawing
(* = special accessories)
Care: see Care Instructions
Flow pressure:
Spanner
Teflo tape
Screwdriver Flashlight
Tape MeasureImpact DrillPencil
3
15121632
215121632 Designed and developed by Bravat/Dietsche GermanyDesigned and developed by Bravat/Dietsche Germany
1 2 3
Hot Cold
56
4
Hot
Cold
Open
Close
Open drainage
Close drainage