Brizo BELO 63052 User manual

PULL-DOWN KITCHEN
AND BAR / PREP FAUCETS
T
E
F
L
O
N
Write purchased model number here.
Models
63052, 63352 &
63952 Series
BELO
®
ASME A112.18.1 / CSA B125.1
®
1
54303 Rev. B
For easy installation of your Brizo®
faucet you will need:
• To READ ALL the instructions
completely before beginning.
• To READ ALL warnings, care, and
maintenance information.
You may need the following tools:
WARNING: THIS FAUCET IS NOT TO BE USED WITH PORTABLE DISHWASHERS!
T
E
F
L
O
N
1/15/10
1/8"

2
All parts and finishes of the Brizo®faucet are
warranted to the original consumer purchaser to
be free from defects in material & workmanship
for as long as the original consumer purchaser
owns their home. Delta Faucet Company
recommends using a professional plumber for
all installation & repair.
Delta will replace, FREE OF CHARGE,
during the warranty period, any part or finish
that proves defective in material and/or
workmanship under normal installation, use
and service. Replacement parts may be
obtained by calling 1-877-345-BRIZO (2749)
(in the U.S. and Canada) or by writing to:
In the United States:
Delta Faucet Company
Product Service
55 E. 111th Street
Indianapolis, IN 46280
In Canada:
Masco Canada Limited, Plumbing Group
Technical Service Centre
420 Burbrook Place
London, ON N6A 4L6
This warranty is extensive in that it covers
replacement of all defective parts and even finish,
but these are the only two things that are
covered. LABOR CHARGES AND/OR DAMAGE
INCURRED IN INSTALLATION, REPAIR, OR
Lifetime Faucet and Finish Limited Warranty
REPLACEMENT AS WELL AS ANY OTHER
KIND OF LOSS OR DAMAGES ARE
EXCLUDED. Proof of purchase (original sales
receipt) from the original consumer purchaser
must be made available to Delta for all warranty
claims. THIS IS THE EXCLUSIVE WARRANTY
BY DELTA FAUCET COMPANY, WHICH DOES
NOT MAKE ANY OTHER WARRANTY OF ANY
KIND, INCLUDING THE IMPLIED WARRANTY
OF MERCHANTABILITY.
This warranty excludes all industrial, commercial
& business usage, whose purchasers are hereby
extended a five year limited warranty from the
date of purchase, with all other terms of this
warranty applying except the duration of the
warranty. This warranty is applicable to Brizo®
faucets manufactured after January 1, 1995.
Some states/provinces do not allow the exclusion
or limitation of incidental or consequential
damages, so the above limitation or exclusion
may not apply to you. Any damage to this faucet
as a result of misuse, abuse, or neglect, or any
use of other than genuine Delta®replacement
parts WILL VOID THE WARRANTY.
This warranty gives you specific legal rights, and
you may also have other rights which vary from
state/province to state/province. It applies only for
Brizo®faucets installed in the United States of
America, Canada, and Mexico.
© 2008 Masco Corporation of Indiana
TABLE OF CONTENTS:
Warranty ------------------------------------------------------------- Page 2
Installation Instructions ----------------------------------------------- Pages 3-15
Plastic Sleeve Installation --------------------------------------------- Page 11
Setting The Handle Limit Stop ----------------------------------------- Page 16
Maintenance -------------------------------------------------------- Page 17
Replacement Parts -------------------------------------------------- Pages 18&19

A. C.
A. Thread hose (1) into spray wand (2). C. Insert hose (1) into and through spout
sub-assembly (2).
3
1
2
1
Hose Installation
1
2
B.
B. To allow for easier assembly, bend
hose near wand as shown.
Bend

A.
A. Verify friction washer (1), spout clip (2) and spout ring (3) are present on
spout assembly.
4
2
Spout Assembly
1
3
2

B. C.
B. Insert hose (1) through guide in hub
and out through mounting shank (2). C. Align button (1) on spout clip with hole in hub (2), then insert spout into hub.
Use back-and-forth motion to insert
spout assembly into hub until clip
button slips into hole. Rotate spout
assembly to ensure smooth
operation. USE CAUTION NOT TO
PINCH FINGERS.
5
Spout Assembly (Continuation)
1
2
1
2

A. B.
A. Remove adhesive backing on trim
ring gasket (1) and press into place
on trim ring (2). Place trim ring on
bottom of spout hub. Insert supply
tubes through mounting hole in sink.
Your faucet is designed for a hole
diameter of 1 3/8" +/- 1/4" (35 mm
+/- 6 mm) and a deck thickness of
up to 3" (76 mm). Maximum deck
thickness of soap dispenser is
3" (76 mm).
B. Push hose (1) partially up into mounting
shank (2). Install the mounting bracket
(3) and nut (4) onto the mounting shank
using wrench (5). For decks up to 1 3/8"
(35 mm) thick use spacer (6) provided
between nut and mounting bracket.
Note 1:The wrench provided is
designed to be used with a variety of
tools: flat/Phillips head screwdrivers,
wrenches, etc. Note 2: For thin gauge
sinks (not recommended), use the
thin deck aid (7) RP49588 as shown
for single and 3 hole installations
to help support the deck. HINT: Turn
the spout tube opposite the handle to
balance the assembly when mounting.
6
3
Faucet Installation - Center Mount
1
2
3
6
2
4
1
5
7

Optional
For optional installations using the 10"
escutcheon, order RP49588 (specify finish)
not supplied. Replace the trim ring with the
10" escutcheon (1) and gasket (2). Push
hose (3) partially up into mounting shank.
Mount as shown above using the
two 1/4-20 studs (4), nuts and washers
(5), bracket (6) with nut and wrench (7).
The wrench provided is designed to
be used with a variety of tools:
flat/Phillips head screwdrivers,
wrenches, etc.
7
3
Optional Escutcheon Installation
1
2
4
5
4
5
6
7
3

Carefully spread apart the supply tubes
(1) to allow hookups and clearance
for bag bracket (2) when installed.
WARNING: Kinked tubes will void the
warranty. Attach bag bracket as shown.
Tighten thumbscrew and nut (3) to secure.
Screw and nut can go either direction.
Note: Squeeze bracket opening
together as shown to aid the bracket in
fitting onto the shank.
8
4
Bag Bracket Installation
2
1
1
3
3
2

A. B.
A. Ensure all fittings and end connections
are free of debris. Faucet fittings (1)
are 3/8" compression, with ends
colored red for hot and blue for cold.
Loop tubing (2) if it is too long. Note:
Recommended tubing minimum
bend diameter is 8". Secure metal
nut (3) on faucet tube to supply valve
connection (4) and hand tighten, then
tighten one additional turn with wrench.
DO NOT OVERTIGHTEN. Repeat
for other tube. WARNING: Do not
use pipe dope or other sealants on
water line connections.
B. Place bucket under faucet quick
connect fitting (1), open both supply
valves (2) and turn faucet valve on by
operating handle (3) for one minute.
Important: This flushes away any
debris that could cause damage
to internal components. When
complete, close both supply valves
and turn faucet valve off to shut off
water flow.
9
Water Line Connections
1
3
4
2
2
1
5A
3
2
2

10
5B
Custom Fit Connections
NOTICE: If you determine the PEX supply
tubing for this faucet is too long and must
be shorter to create an acceptable
installation, be sure to read the instruc-
tions and plan ahead.When cutting the
supply tubing the installer accepts the
responsibility to do so in a way that allows
a leak-free joint to be created. Delta is not
responsible for tubing that is cut too short
or cut in a way that will not allow for a
leak-free joint.
For custom fit installations, you must use
RP50952 sleeves supplied with model and
nuts included on supply lines. Tube cut must
be straight. See plastic sleeve installation
instructions found in RP50952 and included in
this document (page 11) for more information.
Secure metal nut (1) on faucet tube to supply
valve connection (2) and hand tighten, then
tighten an additional 2 turns with wrench. DO
NOT OVERTIGHTEN. Repeat for other tube.
WARNING: Do not use pipe dope or other
sealants on water line connections.
Place bucket under faucet quick connect
fitting (1), open both supply valves (2) and
turn faucet valve on by operating handle (3)
for one minute. Important:This flushes
away any debris that could cause
damage to internal components. When
complete, close both supply valves and turn
faucet valve off to shut off water flow.
Potential Problems and Remedies
lTubing is not cut perpendicular to the
axis of the tub: carefully make an
additional cut, being careful not to cut the
tube too short.
lTubing is cut too short: buy a coupling
union and a replacement supply line that
mate together from a store. The coupling
union end intended to connect to the
faucet must mate to the standard 3/8"
connection nuts and plastic sleeves
supplied with the faucet.
lThe plastic sleeve or connection nut is
lost: purchase a replacement nut and/or
plastic sleeve that are designed to seal
with PEX tubing. NOTICE: DO NOT use a
metal sleeve, RP51243 gasket (supplied
with faucet) or ferrule in the place of the
plastic sleeve supplied, it may not
create a leak-free joint.
A. B.
1
2
2
2
1
A.
B.
3