Brt systems Panl pd100 User manual

PD100 Display

Quick Start Guide

➢Use the RJ45-JST8 cable (in the product package) to connect

the PD100 display to the PanL Hub port. The Cable can reach

a maximum length of 100 meters if needed. The cable has an

RJ45 plug. Therefore, note that an RJ45 socket to RJ45 socket

adapter needs to be used if the extension cable is a plug-to-

plug type such as an Ethernet patch cable.

➢A PanL Hub port can only be connected to one PD100 display

at a time; Daisy chaining is not applicable.

➢An RS485 terminator is built into the PD100 display and

enabled.

PD100 allows different mounting options:

1. Wall Mount

2. Electrical Junction Box Mount

3. Glass Mount

➢ID switch on the back of the displays can be configured for

unique settings or left as factory default. Factory default is 0.

➢Use a Philips head screwdriver to set a unique number

between 0-7 (8- 9 are reserved).

Product Features

PSL Version

PRM Version

Ambient Light Sensor - Automatic screen brightness

control

Time of Flight Sensor - Reserved for Close Object

detection

Buzzer

Status indicator LED Strips - Refer to the LED Status

Indicator section for more details (PRM Version only)

Display Installation

Mounting

ID Switch Configuration

Please visit http://brtsys.com/warranty or scan the QR code

for warranty registration with the UUID and Product Key

below:

STICKER AREA

Glass

Double Sided Tape

Cover Sheet

(Back of Glass)

4. VESA Mount

Mounting

PD100 Display

Quick Start Guide

Status

LED Color (Normal Mode)

LED Color (Failsafe Mode)

Booting Up

Red

Boot Success

Cyan

Red (Blink at 2Hz)

Lost Link to Hub

Orange

Red (Blink at 2Hz)

Communication Error

Red (Blink at 2Hz)

While communicating with Hub

Red (Blink at 2Hz)

Waiting for Recovery

Red <-> Cyan at 2Hz

Recovery in Progress

Red <-> Orange at 2Hz

Recovery Done

Cyan (Blink at 2Hz)

Waiting for Configuration

Orange (Blink at 2Hz)

License Expiry

Red

Note: PD100 enters Normal Mode when there are no failures; on the other hand, it enters FailSafe Mode if there are any failures. As an example, PD100 enters

FailSafe mode if an application image cannot be loaded. Use the application recovery feature to recover in this case.

The LED indicator at the side of the PD100 Display shows different display status as detailed in the table below -

Device Start up Animation/Image After Power Up

PD100 will display the following startup animation/image after connecting to the PanL Hub and powering ON. The LEDs on the PRM version will blink.

PSL Version

PRM Version

LED Status Indicator

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to

provide reasonable protection against harmful interference in a building installation. This equipment generates, uses and can radiate radio frequency energy and, if

not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference

will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be d etermined by turning the

equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

-Reorient or relocate the receiving antenna.

-Increase the separation between the equipment and receiver.

-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

-Consult the dealer or an experienced radio/TV technician for help.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and

(2) This device must accept any interference received, including interference that may cause undesired operation.

FCC Radiation Exposure Statement

This device complies with FCC radiation exposure limits set forth for an uncontrolled environment and it also complies with Part 15 of the FCC RF Rules. This