BTC BCE5232IB User manual

Dual Digital Storage Drive
CD-RW 5232IB
User’s Manual

DANGER INVISIBLE LASER RADIATION WHEN OPEN AVOID DIRECT EXPOSURE TO BEAM
VORSICHT INSICHTBARE LASERSTRAHLUNG WENN ABDECKUNG GEÖFFNET NICHT
DEM STRAHL AUSSETSEN
ATTENTION RADIATION DU FAISCEAU LASER INVISIBLE EN CAS D’OUVERTURE.
EVITER TOUTE EXPOSITION AUX RAYONS.
Copyright Statement
It is a criminal offence, under applicable copyright laws, to make unauthorised
copies of copyright-protected material, including computer programs, films,
broadcasts and sound recordings. This equipment should not be used for such
purposes.
CLASS 1 LASER PRODUCT
APPAREIL A LASER DE CLASSE 1
LASER KLASSE 1
LUOKAN 1 LASERLAITE
PRODUIT LASER
CATEGORIE 1

FCC Compliance Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
1. this device may not cause harmful interference, and
2. this device must accept any interference received, including interference that
may cause undesired operation.
FCC Warning Statement
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can emit radio frequency energy
and, if not installed or used in accordance with the instructions, may cause
interference to radio communications. However, television reception interference
can be determined by turning the equipment off and on. The user is encouraged to
correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna
• Increase the separation between the equipment and the receiver
• Connect the equipment into an outlet different from that to which the receiver
is connected
• Consult the dealer or an experienced radio/TV technician for help.
CAUTION
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
FOR EUROPE
“The drive is in conformity with the EMC directive and low-voltage
directive.”

Table of Contents
INTRODUCTION 1
SYSTEM REQUIREMENTS 2
PACKAGE CONTENTS 2
INSTALLATION 3
HOST INTERFACE CONNECTIONS 3
HARDWARE INSTALLATION 4
DRIVER INSTALLATION 6
For the CD-RW Drive 6
For the Card Reader 6
SOFTWARE INSTALLATION 9
Windows Environment 9
CONNECTION & OPERATION 10
FRONT PANEL 10
REAR VIEW 12
TECHNICAL DATA 14

CD-RW 5232IB
1
INTRODUCTION
Thank you for the purchase of CD-RW 5232IB, a perfect and compact dual
digital storage drive with the combination of an IDE CD-ReWritable drive
and a USB-connected card reader.
CD-RW 5232IB backs up all writing modes and different CD formats. It
supports maximum 52x speed writing ability on CD-R discs, 32x speed on
CD-RW discs and 52x speed reading performance. Other than that, the
built-in 7 in 1 card reader which offers read-write capabilities of 7 memory
card types simplifies the process of exchanging data between digital
cameras, voice recorders, PDAs, MP3s… and your computer.
With this multi-functional solution and the bundled software package, you
can view, archive, or write files/photos/video/music directly from the drive
and enjoy the fascinating digital entertainment on your desktop.
Here are some important features of CD-RW 5232IB:
♦ Easy installation with CD-RW drive of EIDE and card reader of USB
2.0 interface (on-board connection)
♦ 8X, 16X, 24X, 32X, 40X, 48X and 52X writing speed on CD-R media
♦ 4X, 10X, 12X, 16X, 20X, 24X and 32X writing speed on CD-RW
media
♦ Adopts “MTKSuperLink” to prevent Buffer Underrun
♦ Supports MultiRead function
♦ Supports writing modes of TAO, DAO, SAO and packet writing
♦ Four-slot integration of the card reader works with CompactFlash,
MicroDrive, Memory Stick, Memory Stick Pro, MultiMediaCard,
Secure Digital, and SmartMedia
♦ Convenient connection with A-Type USB Extension Port on the front
panel

CD-RW 5232IB
2
System Requirements
For IBM compatible PCs, the system requirements recommended are as
follows:
♦ Pentium II 350MHz above with at least 64MB of memory
♦ Fast and sufficient hard disk space (minimum 200MB for installation,
1GB or more is recommended.)
♦ IDE host interface supporting ATAPI MMC command & USB host
interface (if you don’t have USB on-board connection)
♦ Operating system: Microsoft Windows 98SE/ME/2000/XP
Package Contents
♦ Dual Digital Storage Drive, CD-RW 5232IB
♦ Audio cable
♦ Application software disc
♦ Quick Installation Guide

CD-RW 5232IB
3
INSTALLATION
Host Interface Connections
Most current motherboards have two IDE ports (primary and secondary)
which can connect two IDE cables. Two IDE cables allow you to connect
up to four devices, but it is recommended that you separate IDE ports for
your hard disk and your CD-ReWritable drive. This will ensure that your
hard disk’s performance and speed won’t be affected by having the CD-
RW drive on the same cable.
Cable Select
Slave
Master
If you connect only one device on the cable, you can set the jumper as
“MASTER” or “SLAVE”.
If you connect two devices (e.g. CD-ROM & CD-RW) on the same cable,
set different jumpers for each device (CD-ROM as “MASTER”, CD-RW as
“SLAVE” and vice versa.) The same rule applies to the connection of
having your hard disk and another device on the same cable.
Master
Cable Select
Slave
Jumper

CD-RW 5232IB
4
Hardware Installation
1. Turn off the power to the computer system.
2. Disconnect the power cord and all cables from the back of your
computer, and then remove the cover of the computer.
3. Insert the drive into one of the vacant 5.25" drive bays and secure it
with screws to your PC.
4. Connect one end of the 40-pin IDE cable to the IDE connector of this
drive and the other end to the IDE port on your motherboard. Also,
connect the power supply cable to the back of the drive.
Power In
Audio Out
Digital
Audio Output red edge
 Make sure to align and connect the red-edge of the IDE Cable to Pin
1 on the drive.
5. If you have a sound card that can be connected to this drive, you can
connect the drive (as Audio-out) and the sound card (as Audio-in)
with a 4-pin audio cable.
If your motherboard is integrated with built-in sound system, plug the
4-pin audio cable into the CD-IN connector on the motherboard as
Audio-in.

CD-RW 5232IB
5
6. Connect the USB cable at the back of the drive to the USB header
on the computer’s motherboard. The red wire of the cable needs to
be plugged into Pin 1 on the board.
 This drive supports USB 2.0 and if you connect to USB 1.1
connector, only transfer rate of USB 1.1 will be available.
USB
RED WIRE
IDE
RED WIRE
MOTHER
BOARD
USB Header
Signal
Red/Vcc
White/D-
Green/D+
Black/Ground
Braided Shield Ground
Pin#
1 / 6
2 / 7
3 / 8
4 / 9
5
Error-Proof Pin 10
If the connection is correct, the lower right LED on the front panel
will light green.
7. Re-attach the cover of your computer, and reconnect the power
cord and all cables.

CD-RW 5232IB
6
Driver Installation
For the CD-RW Drive
For the CD-RW drive itself of CD-RW 5232IB, it is an IDE device
supporting Plug & Play, and Windows 98SE/ME/2000/XP can
automatically detect the drive and load the appropriate driver.
For the Card Reader
Windows 98SE/2000
If you run Window 98SE or 2000, please install the provided driver:
1. Insert the application disc.
2. Select:\Card Reader Driver
3. Click “USB Software Installer for 4icons.exe”, and follow the
on-screen instructions: