BTM WM21B012 User manual

Children’s Bus Slide Swing Playset
Installation Manual
Model No.: WM21B012
Test Request: EN71
Test Request Date: 9-Jun-2021

IMPORTANT! KEEP FOR FUTURE REFERENCE
Failure to follow these warnings and the instructions could result in serious injury or death.
This unit must be assembled and disassembled by ADULTS ONLY.
This product is designed for children from 3-6 years old.
DO NOT exceed the maximum weight limit of 50 kg regardless of age.
Always provide the supervision necessary for continued safety of your children.
For domestic use only.
Check this product for damaged hardware, loose joints, missing parts, or shape
edges before assembly and periodically during use.
Swings and slides shall not be installed over concrete, asphalt or any other hard
surface.
DO NOT use this product in any manner other than its intended use.
DO NOT allow more than one child on the wavy slide and ladder at a time.
Children must ALWAYS remain securely seated, in the keep forward facing
position when sliding.
DO NOT lay down, slide from a standing position, or slide down the chute
back-wards.
DO NOT allow children to stand on the slide top.
DO NOT use in adverse weather conditions, while the seats are wet, or in poorly lit
conditions.
DO NOT move the product with child inside.
FALL HAZARD: Children have the risk of suffering injuries after falling from the
slide and swing. To prevent falls, parents should make the following measures:
Stay in arm’s reach of your children.
Always secure this product to support frame by connecting articles.
Changing areas are not designed for children playing.
CHOKING HAZARD: Keep medication and small items that could choke a child
away from the playhouse.

Product Information
Product Name: Children’s Bus Slide Swing Playset
Color available: Blue or Pink
Size: 190*210*116 cm
Weight Capacity: 50 kg
Parts List
A. Screw * 2
B. Hexagon Screw*13
C. Yellow Cross Screw *16
D. Yellow Flower Screw * 7
E. Little Grey Screw*12
F. Round Screw *2
G. White Cross Screw * 2
H. Square Screw * 2
I. Clasp * 4
J. Stopper * 1
K. Short Screw *1
L. Connector * 2
M. Long Screw * 2
N. Plastic Screw Driver* 1
O. Screw Driver * 1

Installation Steps of Bus Part
Step 1
Attach 3 steps to the boards
with 6*Hexagon Screws B.
B. Hexagon Screw
Step 2
Install steering wheel and
control console with 1*
Hexagon Screw B.
B. Hexagon Screw
Step 3
Connect the upper slide and
down slide with 1*short
screw K. Then install slide
and panel with 12*Little
Grey Screws E.
K.Short Screw
E. Little Grey Screw

Step 4
Assemble one side of the bus
and the front board (front
bumper) of the bus with
3*Yellow Cross Screw C.
C.Yellow Cross Screw
Step 5
Install the seat and control
console in the bus.
Step 6
Install the other side of bus
board with 3*Yellow Cross
Screw C.
C. Yellow Cross Screw

Step 7
Install the bumper cover
with 2*Square Screw H and
2* Round Screw F.
H.Square Screw
F. Round Screw
Step 8
Assemble the back panel of
bus and tighten the boards
with 4*Yellow Cross Screw
C. Note: Pay attention to the
installation direction.
C. Yellow Cross Screw
Step 9
Install bus ears with
2*White Cross Screw G.
G. White Cross Screw

Step 10
Install the steps with
2*Yellow Cross Screw C.
C. Yellow Cross Screw
Step 11
Install the slides with
1*Screws A.
A.Screw
Step 12
Fix the platform board with
2* Yellow Cross Screw C.
C. Yellow Cross Screw

Step 13
The guard plate.
Installation Steps of Swing Part
Step 14
Install the guard plate with
2* Yellow Cross Screw C
and 1* Screw A.
C. Yellow Cross Screw
A.Screw

Step 1
Install the base of the swing
with 2*Hexagon Screw B
Install the stopper * 1 on the
base of the swing.
B. Hexagon Screw
J. Stopper
Step 2
Assemble the other board of
swing with 2*Hexagon
Screw B
B. Hexagon Screw
Step 3
Connect the swing seat and
arms with 1*Yellow Flower
Screw D.
Then connect swing panel
and swing seat with 6*
Yellow Flower Screw D.
D. Yellow Flower
Screw

Step 4
Attach the connector 1 * L to
the Rod with a 1 * Long
Screw M and a Screwdriver
O.
M. Long Screw*1
L. Connector * 1
O. Screw Driver
Step 5
Slide the bar all the way
through the swing panels,
insert the 4*Clasps I into the
holes on bar to secure it in
place.Attach the connector 1
* L to the Rod with a 1 *
Long Screw M and a
Screwdriver O.
I. Clasp * 4
M.Long Screw*1
L. Connector * 1
O. Screw Driver

Step 6
Use 2 * Hexagon Screw B to
secure both ends of the
joystick to the outside of the
board.
B. Hexagon Screw
Step 7
After the installation
completes, tear off the
sticker and paste it.
Tips：
This product is available in two forms. If you don’t want to install a
swing, you can choose to install a basketball hoop.