Buckets Of Fun RPBOF User manual

WARNINGS AND SAFETY INSTRUCTIONS
Observe the following warnings an safety instructions to re uce the likelihoo of serious or fatal injury. Save these instruction for future
reference.
Patent Pen ing
Mo el: RPBOF
USER MANUAL
TABLE OF CONTENTS
Warning an Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Assembling the Waterpark Structure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Attaching the Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Operating the Waterpark . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Storing the Waterpark . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
WARNING: CHOKING HAZARD CONTAINS SMALL PARTS. ADULT ASSEMBLY AND SUPERVISION REQUIRED.
IMPORTANT
Inten e for chil ren 2 years an up
Store insi e an o NOT use if temperature is below 32°F
Use clean water in play basin an rinse thoroughly between uses
Drowning Hazar - supervision of an a ult require at all times
Do NOT allow chil ren to assemble this pro uct
Do NOT allow chil ren to climb or swing from the waterpark
NEVER leave chil ren unatten e while the waterpark is in use.
Do NOT leave water in the bucket or basins; empty after use.
Do NOT attempt to move the waterpark when it is fille with water or has water/san in the basins.
Ensure all connections are secure before attaching water supply
Surfaces may become slippery, ensure proper precautions are taken
Do NOT allow chil ren to install batteries
Do NOT mix battery types or mix ol an new batteries
Please v s t www.bofwaterpark.com for full assembly v deo

CONTENTS TOOLS (Not Inclu e )
• Rubber Mallet (Do NOT use a metal hammer)
• Phillips Hea Screw river
• Scissors (may be require to cut funnel hose)
• Measuring Tape (optional)
OTHER SUPPLIES/ACCESSORIES (Not Included)
• Clean, Filtere Play San (if esire )
• (3) AA Batteries
• Bubble solution
• Water/San an Ri ing Toys
ASSEMBLING THE WATERPARK STRUCTURE
Helpful Tips to a Quick Buil :
• Construct on a flat, firm surface - this will help when tapping components
together
• Tap components together after the structure is fully assemble - easier to take
apart if a wrong component is installe
• Wear gloves with a rubber coating - provi es a itional grip on the PVC
components
• A measuring tape can be use to help i entify components if nee e
INSTRUCTIONS
IMPORTANT: Please pay a itional attention to the orientation of the components
when placing them together. Connectors nee to face the correct irection for
proper assembly.
IMPORTANT: Han fit all the components at first. When fully assemble , tap the
unglue components lightly with a rubber mallet (Do NOT use a metal hammer).
IMPORTANT: To re uce leaking, ensure the o-rings are installe in the (4) unions
prior to tightening.
NOTE: The hose connector an o-rings for the unions are in a separate bag.
1. Lay the blue pipe in escen ing or er, as seen in the CONTENTS section of
the manual. This will help to i entify the components (Fig. 1).
2
Item Descr pt on Qty
A Funnel Hose 1
B Dump Bucket 1
C Funnel 1
D Bucket Support Ro 1
E Water An San Basins 2
F Bucket Support Arm (Left) 1
G Bucket Support Arm (Right) 1
H Bucket Fee Line 1
I Table Upright With 4 Way 1
J Main Water Fee (Top) 1
K Main Water Fee (Bottom) 1
L Cross Fee Line 1
M 36" Pipe (Bottom/Table Support) 1
N 33.5" Pipe (Lateral Supports) 3
O 30.5" Pipe (Table Upright - Top) 1
P 24" Pipe (Front Upright - Top) 1
Q 17.25" Pipe (Table Support) 4
R 16" Pipe (Table Upright - Bottom) 2
S 12" Pipe (Table Support) 3
T Table Legs 2
U 24" Pipe With Coupling (Front Upright - Bottom) 1
V 3 Way Tee (Purple) 2
W Elbow (Yellow) 3
X 3 Way Elbow (Re ) 2
Y 4 Way Elbow (Green) 1
Z Bucket Spout 1
AA Bubble Maker Straps 2
BB Self Taping Screws 2
CC Automatic Bubble Maker 1
NOTE: The hose connector an o-rings for the unions are in a separate
bag with the screws an Velcro straps.
Fig. 1

3
2. Assemble the bottom support of the table (Fig. 2).
(1) M 36" Pipe (Bottom/Table Support)
(2) R 16" Pipe (Table Upright - Bottom)
(2) W Elbow (Yellow)
3. Assemble the top cross support of the table (Fig. 3).
(1) I Table Upright With 4 Way
(2) Q 17.25" Pipe (Table Support)
(1) V 3 Way Tee (Purple)
(1) Y 4 Way Elbow (Green)
4. Construct the water an san tables (Fig. 4A - 4C).
(3) S 12" Pipe (Table Support)
(2) Q 17.25" Pipe (Table Support)
(2) X 3 Way Elbow (Re )
(2) T Table Legs
(1) V 3 Way Tee (Purple)
5. Stan the table upright (resting on the yellow elbows/green caps) an install
the top upright (Fig. 5).
(1) O 30.5" Pipe (Table Upright - Top)
6. The following steps will cover the assembly of the opposite si e to the water
an san tables (Fig. 6A - 6C). NOTE: Use an O-ring when connecting the
union
(1) J Main Water Fee (Top)
(1) K Main Water Fee (Bottom)
(2) N 33.5" Pipe (Latteral Supports)
(1) W Elbow (Yellow)
(1) P 24" Pipe (Front Upright - Top)
(1) U 24" Pipe With Coupling (Front Upright - Bottom)
Fig. 2
Fig. 3
Fig. 4A
Fig. 4B
Fig. 4C
Fig. 5

Connect by tightening the union.
7. Connect the two halves of the waterpark together by attache the Cross Fee
Line an install the lateral support for the bucket assembly (Fig. 7A - 7C).
NOTE: Use an O-ring when connecting the union.
(1) L Cross Fee Line
(1) N 33.5" Pipe (Lateral Supports)
Connect by tightening the union. Stan the structure an align the union with
the water an san table structure. Tighten the union to connect the two
structures
4
Stan the structure an align the union with the water an san table structure.
Tighten the union to connect the two structures
Lay out the components as shown, ensuring the yellow an re elbows are
arrange properly. In a ition, ensure the counterweight, insi e the bucket
(i entifie by the arrow), is in the correct position (Fig. 8A).
8. Assemble the Dump Bucket (Fig. 8A - 8D).
(1) B Dump Bucket
(1) D Bucket Support Ro
(1) F Bucket Support Arm (Left)
(1) G Bucket Support Arm (Right)
Fig. 6A
Fig. 6B
Fig. 6C
Fig. 7A
Fig. 7B
Fig. 7C
Fig. 8A

Sli e Dump Bucket (B) onto Support Ro (D) as shown (Fig. 8C).
Sli e Left Support Arm (F) onto Support Ro (D) as shown (Fig. 8D).
9. Attach the Dump Bucket Assembly to the waterpark structure as shown (Fig. 9).
NOTE: The Dump Bucket shoul tilt slightly towar the center of the waterpark. If
it is tilting away from the center, the bucket may be installe backwar s - please
check the location of the counterweight.
10. Connect the Bucket Fee Line (Fig 10A an 10B). NOTE: Use an O-ring
when connecting the union.
(1) H Bucket Fee Line
Tighten the union from the Cross Fee Line an secure the front en with
the yellow elbows from the Bucket Support Arms as shown (Fig. 10)
.
11. Connect the Bucket Spout (Z) to the Bucket Fee Line (H) as
shown (Fig 11A an 11B)
IMPORTANT: Turn from the bottom of the spout, an o NOT over tighten. A
snug fit is all that is nee e . Do NOT force the spout to finish a rotation. It oes
not have to be tightene all the way to work properly.
Ensure that the spout is in line with the Bucket Fee Line an the center of the
Dump Bucket (Fig. 11B).
12. Using a rubber mallet (Do NOT use a metal hammer), lightly tap all the non-
glue components together to ensure they are secure an square.
The assistance of a secon person to hol the opposing si e when tapping
connections together will make this step easier.
13. Secure the hose connector to the Main Water Fee (K) an ensure the gasket
is in place.
5
Fig. 8B
Fig. 8C
Fig. 9
Fig. 10
Fig. 8D
Fig. 11A
Fig. 11B
Insert Support Ro (D) into the Right Support Arm (G) as shown (Fig. 8B).

ATTACHING THE ACCESSORIES
IMPORTANT: Before attaching accessories, it is recommen e to place the
waterpark in the location it will be use .
1. Insert AA batteries (NOT inclu e ) into the Bubble Maker. Attach the Bubble
Maker (CC) to the center of the top lateral pipe, across from the water an
san tables using Straps (AA) as shown (Fig. 12).
2. Secure the Funnel to the front upright.
IMPORTANT: Do NOT screw into any pipe that has a union or is esignate
as a "fee line". Look at the location of the funnel before screwing into the pipe.
(1) A Funnel Hose
(1) C Funnel
(2) BB Self Tapping Screws
Using a Phillips hea screw river, attach the funnel just above the coupling
of the front upright, opposite of the water an san tables as shown (Fig. 13).
-
Insert the Funnel Hose (A) into the bottom of the Funnel (C) an then wrap
the hose twice aroun the upright. Secure the hose to the bottom of the
upright with a Self Tapping Screw (BB) by screwing through the insi e
portion of the hose only as shown (Fig. 14).
NOTE: Scissors may be necessary to cut the hose to the esire length.
3. Insert the (2) Water an San Basins (E) into the table frames (Fig. 15).
IMPORTANT: Tap all connections together prior to installing bins. Use a
rubber mallet an tap front to back an si e to si e, ensuring the pipes are
all the way insi e the fittings.
OPERATING THE WATERPARK
WARNING: Do NOT allow chil ren to use the waterpark unless there is proper
supervision.
WARNING: NEVER leave chil ren unatten e while the waterpark is in use.
WARNING: Do NOT leave water in the bucket or basins; empty after use.
WARNING: Ensure all fittings are secure before operating the waterpark.
WARNING: Surfaces may become slippery, ensure proper precautions are taken
IMPORTANT: Ensure the waterpark is in the location where it will be use . Do
NOT attempt to move the waterpark when it is fille with water or has water/san
in the basins.
6
Fig. 12
Fig. 13
Fig. 14
Fig. 15

7
1. Use a gar en hose to fill one or both basins with water. Only fill the basins
halfway with water.
2. Fill a secon basin, if esire , with clean, filtere play san (NOT
INCLUDED). Only fill half way with san .
3. A bubbles to the Bubble Maker. Press an release the top button to turn
On/Off.
4. Secure the gar en hose to the waterpark as shown (Fig. 16).
5. Gra ually opening the valve to the full position. Allow water to flow through
the entire waterpark until it pours out of the spout, into the Dump Bucket.
NOTE: The Dump Bucket may continuously spin when the hose valve is fully
open. This step is just to fill the entire waterpark.
6. Gra ually turn the gar en hose valve to re uce the water supply to the
waterpark until the ump bucket stops spinning an catches water.
NOTE: A goo flow of water allows the bucket to ump once every 25 - 35
secon s.
NOTE: Monitor the area aroun the waterpark for pu les an move the
waterpark accor ingly.
STORING THE WATERPARK
WARNING: Do NOT leave water in the bucket or basins; empty after use.
IMPORTANT: Do NOT use or leave water in the waterpark if temperatures fall
below 32°F.
IMPORTANT: Do NOT attempt to move the waterpark when it is fille with water
or has water/san in the basins.
NOTE: The waterpark oes not nee to be isassemble between uses.
1. Turn the water supply to the OFF position.
2. Release the hose from the waterpark connector (water will flow from the pipe).
3. Remove both basins an empty any water basin.
NOTE: If san is use in the secon basin, the first basin can be use as a c
over to keep san clean.
4. Empty any water left in the Dump Bucket.
5. Using the front uprights, gently tilt the waterpark upwar , lifting the front a
few inches. This will allow excess water to escape through the open hose
connector.
6. Move the waterpark to a sha e area away from heavy traffic.
NOTE: For longer term storage it is goo practice to release a few
connections to ensure all water has been emptie from the waterpark.
For assistance please contact our support line at [phone]
Fig. 16

Thank you fo pu chasing
Buckets of Fun 6-in-1
Backya d Wate pa k!
We know you kids will have a blast!
We'd love to sha e in the excitement, so please post you
images, videos and comments to Facebook and Instag am.
Please find us @backya dwate pa k and use
#hadbucketsoffun.
"My kids #hadbucketsoffun with thei new backya d
wate pa k!"
Thank you!