Buckeye X80 Activator User manual

X80 Wireless Camera System
User's Manual
Version 2.0
www.buckeyecam.com

Table of Contents
1. Warnings.................................................................................................................................................... 2
2. Overview.................................................................................................................................................... 3
3. Getting Started........................................................................................................................................... 5
4. Connecting to a PC Base...........................................................................................................................6
5. Connecting to a Cell Base..........................................................................................................................
6. Connecting to a Net Base.........................................................................................................................12
. Register Cameras..................................................................................................................................... 15
8. Camera Settings....................................................................................................................................... 1
9. Camera Installation................................................................................................................................... 19
10. Antennas................................................................................................................................................ 22
11. Repeaters............................................................................................................................................... 24
12. Camera Technical Specifications............................................................................................................26
13. Camera Base......................................................................................................................................... 29
14. Troubleshooting...................................................................................................................................... 32
15. Additional Information............................................................................................................................. 34
16. Warranty and Service.............................................................................................................................35
X80 Wireless Camera User's Manual v2.0 1 of 35

1. Warnings
1. Warnings
Contains FCC ID:MCQ-XBEE09P The enclosed device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions: (i.) this device may not cause harmful
interference and (ii.) this device must accept any interference received, including interference that
may cause undesired operation.
If the camera is used with any antenna other than the portable antenna supplied with the X Series
Camera Unit or PCBase Unit, the system may not comply with the FCC regulation Part 15.24 ,
Operation within the license-free band 902 – 928 MHz. Contact manufacturer regarding use of
optional high-gain antennas with the X80 Wireless Camera System.
To satisfy FCC RF exposure requirements for mobile transmitting devices, a separation distance of
20 cm or more should be maintained between the antenna of this device and persons during
device operation. To ensure compliance, operations at closer than this distance are not
recommended. The antenna used for this transmitter must not be co-located in conjunction with
any other antenna or transmitter.
This product should not be used in any application where product failure may cause injury to
persons, loss of life, or catastrophic property damage.
X80 Wireless Camera User's Manual v2.0 2 of 35

2. Overview
2. Overview
When a camera detects motion, a picture or video is taken and transmitted to a base receiver. Up
to 254 cameras can be assigned to one base. Four different base options are available.
Transmission distance may be up to 1-2 miles with standard antennas. Transmission distance can
be increased by using high gain antennas or repeaters.
X80 Wireless Camera User's Manual v2.0 3 of 35
Camera Base
● Computer is NOT required
● Camera acts as base with SD card
● Cell service is NOT required
Net Base
● Connects to computer with Ethernet
● Uses existing network
● Cell service is NOT required
Cell Base
● Connects to computer over Internet
● One cellular data plan is required
● Works with most cell providers
C Base
● Connects to computer with USB
● Lowest cost base option
● Cell service is NOT required

2. Overview
Images are received and all of the camera settings are controlled using the X-Series Network
Manager software application.
Images can be viewed from X-Series Network Manager, or automatically emailed, or uploaded to
your account at livecam.buckeyecam.com, making them easily accessible from smartphones or
tablets.
The cameras are powered with rechargeable lead acid batteries and can take thousands of
pictures on a single charge. Optional solar panel chargers are available to extend battery life
indefinitely. The camera and battery pack are housed in watertight, weatherproof enclosures for
reliable outdoor operation.
X80 Wireless Camera User's Manual v2.0 4 of 35

3. Getting Starte
3. Getting Started
If you are using a PC Base, Cell Base, or Net Base, follow the steps below to set up your system.
If you are using a Camera Base, go to chapter 13.
Install X-Series Network Manager and USB Modem Driver for Windows.
Use the supplied installation CD or download at
www.buckeyecam.com/site/support.html
Connect to a Base.
For PC Base refer to chapter 4.
For Cell Base refer to chapter 5.
For Net Base refer to chapter 6.
Register cameras.
Refer to chapter .
Adjust camera settings.
Refer to chapter 8.
Install cameras in their permanent location.
Refer to chapter 9.
X80 Wireless Camera User's Manual v2.0 5 of 35
Getting Started
1
Getting Started
2
Getting Started
3
Getting Started
4
Getting Started
5

4. Connecting to a PC Base
4. Connecting to a C Base
Attach antenna.
Connect C Base to computer with USB cable.
Minimum computer requirements are :
Windows XP or later, 128 MB RAM,
1.5 GB disk space, USB port.
Start X-Series Network Manager
and click the CBase icon.
Click the Connect button.
Click the Done button.
X80 Wireless Camera User's Manual v2.0 6 of 35
C Base
1
C Base
2
C Base
3
C Base
4
C Base
5
The PC Base is for indoor use only.
If optional high gain antenna will be
used, refer to Chapter 10.

5. Connecting to a Cell Base
5. Connecting to a Cell Base
Make sure your Cell Base has an active cellular data account.
If you need assistance setting up an account contact Buckeye Cam Service
at 866-325-81 2 ex 1195, or www.buckeyecam.com.
Connect the power source.
If you are using the AC/DC wall adapter (provided), proceed to step A1.
If you are using an external battery (not provided), proceed to step B1.
Connect the pigtail to the AC/DC wall adapter.
Connect the AC/DC wall adapter to the Cell Base.
lug the AC/DC wall adapter into an AC power outlet.
roceed to Cell Base step 2
X80 Wireless Camera User's Manual v2.0 of 35
A1
A2
The AC/DC wall adapter is for indoor use only.
A3
A4
Cell Base
2
Cell Base
1

5. Connecting to a Cell Base
Connect the battery cable to the
battery.
Use the provided battery cable to connect
to a 12 Volt 2 DP-DL marine battery
(or equivalent).
(Battery is not provided).
Connect optional solar charger (if used).
Use Buckeye Cam part number 99 -0014 only.
Connect the battery cable to the Cell Base.
X80 Wireless Camera User's Manual v2.0 8 of 35
Battery charging may produce potentially explosive gas. Do
not charge battery in a sealed enclosure.
B1
B2
B3

5. Connecting to a Cell Base
Connect the antennas.
Open the enclosure lid.
Move the toggle switch down to the ON position.
Wait for the first LED to blink slowly and the second
to be on solid.
This may take several minutes.
X80 Wireless Camera User's Manual v2.0 9 of 35
Cell
Camera
Cell Base
3
Cell Base
4
Cell Base
5
Cell Base
6
O
N
Blink
On

5. Connecting to a Cell Base
Start X-Series Network Manager and
click on the Cell Base icon.
Enter the I Address / Domain Name and Authentication
Code from the Cell Base Information Sheet.
X80 Wireless Camera User's Manual v2.0 10 of 35
Cell Base
7
Cell Base
8
Keep the Cell Base Information Sheet in a safe place. You may
need it again if you need to re-enter the connection setup or if you
need to contact Buckeye Cam tech support.

5. Connecting to a Cell Base
Set connection default options.
These should be checked for normal use.
Enable or Disable Low Battery Detection.
If this box is checked, the cellular connection will
be turned off when the battery is low. This will
prevent battery damage. It will be automatically
turned back on if the battery charges back up to
a sufficient level (e.g. by solar charger).
Select the check connection and lost
connection times.
The connection to the Cell Base may be lost due
to a temporary Internet outage or a dropped cell
signal. X-Series Network Manager will periodically
check the connection and try to reconnect if it is lost.
Shorter time settings will result in less down time
but will use slightly more battery power.
Click the Connect button.
Click the Done button.
Close the enclosure lid.
X80 Wireless Camera User's Manual v2.0 11 of 35
Cell Base
9
Cell Base
10
Cell Base
11
Cell Base
13
Cell Base
14
Cell Base
15
It is recommended to check this box if the
Cell Base is powered with a battery.

6. Connecting to a Net Base
6. Connecting to a Net Base
Connect the pigtail to the AC/DC wall adapter.
Connect the AC/DC wall adapter to the Net Base.
lug the AC/DC wall adapter into an AC power outlet.
Open the enclosure lid.
Move the toggle switch down to the ON position.
X80 Wireless Camera User's Manual v2.0 12 of 35
Net Base
1
Net Base
2
Net Base
3The AC/DC wall adapter is for indoor use only.
Net Base
4
O
N
Net Base
5

6. Connecting to a Net Base
Connect to the network with an
Ethernet cable.
Start X-Series Network Manager and
click on the Net Base icon.
Enter the I Address / Domain Name.
In order for X-Series Network Manager to
connect to a Net Base, it must know the IP
address that has been assigned to it.
The IP address is assigned to the Net Base
by a DHCP server running on the local network.
The DHCP server may be running on a gateway
or router. You will need to access the client list
table and find the IP address that matches the
MAC address that is on the sticker inside of the
Net Base.
You may need to refer to the gateway or router
documentation for instructions on how to access
the client list table.
X80 Wireless Camera User's Manual v2.0 13 of 35
Net Base
6
Net Base
7
Net Base
8

6. Connecting to a Net Base
Enter the Authentication Code from the Net Base
Information Sheet.
Set the Check connection and lost connection times.
The default time of 1 minute is adequate for most applications.
Click the connect button.
Close the enclosure lid.
X80 Wireless Camera User's Manual v2.0 14 of 35
Net Base
9
Keep the Net Base Information Sheet in a safe place. You may
need it again if you need to re-enter the connection setup or if you
need to contact Buckeye Cam tech support.
Net Base
10
Net Base
11
Net Base
12

7. Register Cameras
7. Register Cameras
Connect the camera antenna.
Install a UB1270 battery into the battery pack.
The red wire connects to battery (+). The black
wire connects to battery (-).
Close and latch the battery pack and connect
it to the camera.
Open the camera enclosure and wait for the LCD
display to show “Not Registered Waiting for Base”.
X80 Wireless Camera User's Manual v2.0 15 of 35
Register
2
Register
3
Register
1
Register
4

7. Register Cameras
In X-Series Network Manager
click A /Remove Device.
Drag the camera icon and drop
it into the network view.
Repeat for all cameras.
Click Done when finished.
Close the camera enclosure(s).
After a camera is successfully registered, the LCD
display will show the camera number.
X80 Wireless Camera User's Manual v2.0 16 of 35
Register
5
Register
6
Register
7
Register
8

8. Camera Settings
8. Camera Settings
To access the camera settings for any camera, click on the camera icon in the network view to
open the camera Control Panel.
Click on the Settings button from the camera Control Panel. ( Note: The X-Series Network
Manager window is re-sizable. If you do not see the Settings button, you may need to use the
scroll bar on the right side of the window to scroll down. )
X80 Wireless Camera User's Manual v2.0 1 of 35
Click to open
Control Panel
Settings

8. Camera Settings
Stamps on pictures
Time, Date, Moon Phase, and Temperature may be added to pictures by checking the appropriate
box. Custom text may be entered in the Text 1 and Text 2 fields. This text may be added to
pictures by checking the box next to each field.
Image format
Click on the arrow to select the image format. Select the picture resolution – or video.
Delay between motion triggers
Click on the arrow to select the delay between motion triggers. If a camera receives a motion
trigger, it will not respond to another trigger until the delay time has elapsed.
Motion sensor
Click on the arrow to select the motion sensor sensitivity. To disable the motion sensor, set the
sensitivity to Off.
ictures per motion trigger
Click the arrow to select the pictures per motion trigger value. When the value is set to 1, the
camera will take 1 picture each time it is triggered. To take multiple pictures with each trigger, set
the value greater than 1. For example, if the value is set to 3, the camera will take 3 pictures, as
fast as possible, each time it is triggered.
Blink LED when motion detected
Click the Yes/No toggle button to enable or disable a blinking LED when the camera detects
motion. This is a visible red LED on the front of the camera. It is very useful for doing a “walk test”
in front of the camera to verify that it is triggering correctly. (Note: If camera concealment is
important, this option should be set to No after the camera is installed in the permanent location.)
Camera schedule
Click the On/Off toggle button to turn the camera schedule on or off. Using the camera schedule,
the camera may be disabled at certain times of the day, or use different settings a different times of
the day.
Transmit last picture first
Click the On/Off toggle button to turn on “transmit last picture first”. This setting controls how the
camera transmits pictures when there is more than one picture waiting to be transmitted. If this
button is set to Off, the pictures will be transmitted in the order they were taken. If it is set to On,
they are transmitted latest picture first.
Automatically delete files
Click the arrow to change this setting. This can be used to have X-Series Network Manager
automatically delete pictures from your computer after a certain period of time. If it is set to Never,
X-Series Network Manager will never delete pictures from your computer.
Stamps on pictures
Click the Add Time Lapse button to setup a time lapse schedule.
X80 Wireless Camera User's Manual v2.0 18 of 35

9. Camera Installation
9. Camera Installation
Attach camera to a solid structure.
The supplied spring buckle strap may be
used to attach the camera to a tree,
vertical post, or other solid structure.
Alternatively, it may be attached with a
screw or nail using the hole in the top
of the mounting bracket.
The best height for the camera will
depend on the primary target of interest.
Usually, the camera should be placed at
about the height of the center of mass
of the primary target of interest.
For maximum motion trigger distance,
the face of the camera should be
perpendicular to the ground.
If maximum motion trigger distance
is not critical, the camera may be placed
at an angle.
Connect battery pack.
If you have not done so already, install
the battery (see Chapter ).
The supplied spring buckle strap may be
used to attach the battery pack to the
same solid structure as the camera.
It may also be attached with a screw or
nail using the hole in the top of the bracket.
Alternatively, the battery pack may be
placed on the ground. This may make it
easier to conceal.
The battery pack is watertight, however it
should not be submerged.
Once the battery pack is in place, connect
it to the camera with the supplied cable.
X80 Wireless Camera User's Manual v2.0 19 of 35
Install
1
Install
2