Bull 32X SCSI-2 CD-ROM Drive Guide

Bull
32X SCSI–2 CD–ROM Drive
Installation and Using Guide
86 A1 15EG 00
ORDER REFERENCE

Bull
32X SCSI–2 CD–ROM Drive
Installation and Using Guide
Hardware
December 2002
BULL CEDOC
357 AVENUE PATTON
B.P.20845
49008 ANGERS CEDEX 01
FRANCE
86 A1 15EG 00
ORDER REFERENCE

The following copyright notice protects this book under the Copyright laws of the United States of America
and other countries which prohibit such actions as, but not limited to, copying, distributing, modifying, and
making derivative works.
Copyright Bull S.A. 1992, 2002
Printed in France
Suggestions and criticisms concerning the form, content, and presentation of
this book are invited. A form is provided at the end of this book for this purpose.
To order additional copies of this book or other Bull Technical Publications, you
are invited to use the Ordering Form also provided at the end of this book.
Trademarks and Acknowledgements
We acknowledge the right of proprietors of trademarks mentioned in this book.
AIXRis a registered trademark of International Business Machines Corporation, and is being used under
licence.
UNIX is a registered trademark in the United States of America and other countries licensed exclusively through
the Open Group.
Linux is a registered trademark of Linus Torvalds.
The information in this document is subject to change without notice. Groupe Bull will not be liable for errors
contained herein, or for incidental or consequential damages in connection with the use of this material.

Contents
Safety Information.......................v
Laser Safety Information .....................v
Laser Compliance ......................v
Handling Static-Sensitive Devices.................vii
About This Book .......................ix
ISO 9000 ..........................ix
Related Publications ......................ix
Trademarks .........................ix
Chapter 1. Overview ......................1
Front View of the CD-ROM Drive ..................2
Rear View of the CD-ROM Drive ..................2
Chapter 2. Preparing to Install the 32X SCSI-2 CD-ROM Drive .......3
Verifying Your Hardware Requirements ................3
Verifying Your Software Requirements ................3
Checking Your Package .....................3
Gathering Tools and Documentation .................3
Planning Your SCSI Device Layout .................4
Determining Your SCSI Device Address ................4
Setting the SCSI Address.....................5
Rear View and Jumper Pin Positions on the 32X SCSI-2 CD-ROM Drive .....7
Chapter 3. Installing the 32X SCSI-2 CD-ROM Drive ...........9
Installing and Connecting the Drive .................9
Configuring the 32X SCSI-2 CD-ROM Drive ..............10
Verifying the Installation .....................10
Extending the Vertical Retaining Tabs ................11
Chapter 4. Installing Device Driver Software .............13
Installing Device Drivers on an AIX System ..............13
Chapter 5. Using the32X SCSI-2 CD-ROM Drive ............15
Understanding the Status Lights ..................15
Other Handling Considerations ..................15
Handling Compact Discs ....................16
Loading a Compact Disc Horizontally ................16
Loading a Compact Disc Vertically .................17
Opening the Tray Manually....................17
Playing an Audio CD ......................18
Appendix A. Communications Statements ..............19
Federal Communications Commission (FCC) Statement ..........19
European Union (EU) Statement ..................20
iii

International Electrotechnical Commission (IEC) Statement .........20
United Kingdom Telecommunications Safety Requirements .........20
Avis de conformité aux normes du ministère des Communications du Canada. . . 21
Canadian Department of Communications Compliance Statement .......21
VCCI Statement .......................21
Radio Protection for Germany ...................21
Appendix B. Notices .....................23
iv 32X SCSI-2 CD-ROM Drive Installation and Using Guide

Safety Information
DANGER
An electrical outlet that is not correctly wired could place hazardous voltage
on metal parts of the system or the devices that attach to the system. It is the
responsibility of the customer to ensure that the outlet is correctly wired and
grounded to prevent an electrical shock.
Before installing or removing signal cables, ensure that the power cables for
the system unit and all attached devices are unplugged.
When adding or removing any additional devices to or from the system,
ensure that the power cables for those devices are unplugged before the
signal cables are connected. If possible, disconnect all power cables from the
existing system before you add a device.
Use one hand, when possible, to connect or disconnect signal cables to
prevent a possible shock from touching two surfaces with different electrical
potentials.
During an electrical storm, do not connect cables for display stations, printers,
telephones, or station protectors for communications lines.
D05
Laser Safety Information
CAUTION:
This product may contain a CD-ROM which is a class 1 laser product.
C29
Laser Compliance
All lasers are certified in the U.S. to conform to the requirements of DHHS 21 CFR
Subchapter J for class 1 laser products. Outside the U.S., they are certified to be in
compliance with the IEC 825 (first edition 1984) as a class 1 laser product. Consult the
label on each part for laser certification numbers and approval information.
CAUTION:
All IBM laser modules are designed so that there is never any human access to
laser radiation above a class 1 level during normal operation, user maintenance,
or prescribed service conditions. Data processing environments can contain
equipment transmitting on system links with laser modules that operate at
greater than class 1 power levels. For this reason, never look into the end of an
optical fiber cable or open receptacle. Only trained service personnel should
perform the inspection or repair of optical fiber cable assemblies and receptacles.
C25
v

vi 32X SCSI-2 CD-ROM Drive Installation and Using Guide

Handling Static-Sensitive Devices
Attention: Static electricity can damage the device and your system unit. To avoid
damage, keep this device in its anti-static protective bag until you are ready to install it.
To reduce the possibility of electrostatic discharge, follow the precautions listed below:
vLimit your movement. Movement can cause static electricity to build up around you.
vHandle the device carefully, holding it by its edges or its frame.
vDo not touch solder joints, pins, or exposed printed circuitry.
vDo not leave the device where others can handle and possibly damage the device.
vWhile the CD-ROM drive is still in its anti-static package, touch it to an unpainted
metal part of the system unit for at least two seconds. (This drains static electricity
from the package and from your body.)
vRemove the device from its package and install it directly into your system unit
without setting it down. If it is necessary to set the device down, place it on its
static-protective package. (If your device is an adapter, place it component-side up.)
Do not place the device on your system unit cover or on a metal table.
vTake additional care when handling devices during cold weather, as heating reduces
indoor humidity and increases static electricity.
vii

viii 32X SCSI-2 CD-ROM Drive Installation and Using Guide