Butts of Bawtry TBT2586 User manual

GASOLINE CHAIN SAW 12”TBT2586
INSTRUCTION MANUAL
WARNING
•Before using our products, please read this
manual carefully to understand the proper use
of your unit. Keep this manual handy.
•This chain saw is of a special type designed
especially for tree service. It is only to be used
by a trained operator.
SAVE THESE INSTRUCTIONS FOR REFERENCE

SAFETY FIRST
Instructions contained in warnings within this manual marked with a symbol
concern critical points which must be taken into consideration to prevent possible
serious bodily injury, and for this reason you are requested to read all such instructions
carefully and follow them without fail.
■WARNINGS IN THE MANUAL
This mark indicates instructions which must be followed in order to prevent accidents
which could lead to serious bodily injury or death.
This mark indicates instructions which must be followed, or it
leads to mechanical failure, breakdown, or damage.
This mark indicates hints or directions useful in the use of the product.
1. Parts location……………………………………………………………………………4
2. Symbols on the machine………………………………………………………………5
3. For safe operation…………………………………………………………………… 8
4. Installing guide bar and saw chain…………………………………………………12
5. Fuel and chain oil……………………………………………………………………15
6. Operation ……………………………………………………………………………17
7. Sawing ………………………………………………………………………………21
8. Working with tree service chain-saws from rope and harness…………………24
9. Maintenance…………………………………………………………………………31
10. Maintenance of Saw Chain and Guide Bar ………………………………………34
11. Storage………………………………………………………………………………37
12. Waste disposal and environmental protection……………………………………37
13. Warranty………………………………………………………………………………37
14. Troubleshooting guide………………………………………………………………38
15. Specifications ………………………………………………………………………39

Attention ! Read these notes before you start working with the saw and
keep them.
Read the instructions carefully. Familiarise with the control elements so that
you are able to safely operate the device. Always keep these Operating
Instructions together with the chain saw.
Attention! Risk of hearing defects.
Under normal operating conditions, this device can expose the operator to a
noise level of 80 dB(A) or more.
Attention: Noise protection ! Please observe the local regulations when
operating your device.
Intended / not intended use:
The chain saw serves trunks, square timbers and for cutting branches, according to
the available cutting length. Only materials from wood may be worked on.
Sufficient personal protection equipment (PPE) is required according to the operating
instructions during the use. This product is designed for use by a trained operator for
pruning and dismantling standing tree crowns. For damage or injuries which resulting
from misapplication are responsible by the user/operator and not the manufacturer.
Suitable sawing chains, guide bars combinations may be used as mentioned in the
operating instructions only for the machine. A component of the intended use is also
the attention of the safety references, as well as the operating instructions in the
operating instructions. Persons, who serve the machine, must make themselves
trained and familiar with this product and think over all the possible dangers. Beyond
that the valid rules for the prevention of accidents are to be kept in every detail. Other
general rules within ranges according to industrial medicine and in terms of safety are
to be considered. Changes in the machine completely exclude an support of the
manufacturer and from it developing damage and lead to expiring the warranty. This
equipment is designed for use in home garden.
Remainder driven
Also when appropriate using the tool always remains a certain residual risk, which
cannot be excluded. From the kind and construction of the tool the following potential
endangerments can be derived:
- Contact with the unprotected sawing chain (cuts)
- Unexpected, sudden movement of the sawing sword (cuts)
- Damage of the ears, if no prescribed protection of the ears is carried
- Inhale from poisonous particle, exhaust gases of the combustion engine
- Contact of gasoline on the skin

- Noise. A degree of noise from the machine is not avoidable. Route noisy work is to
be licensed and limits for certain periods. Keep rest periods and they may need to
restrict the working hours to a minimum. For their personal protection and protection
of people working nearby, an appropriate hearing protection shall be worn;
- Vibration. Warning: The actual existing vibration emission value during use of the
machine can deviate from the manual or the manufacturer specified. This can be
caused by the following factors, before or during each of use should be considered:
- If the machine is used correctly
- If the method of cutting the material and how it is processed correctly.
- The use of the machine state is in the regulatory
- Sharpness condition of cutting tool or cutting tool real
- The grab handles are mounted back to optional vibration handles and are they fixed
to the machine body.
If you notice an unpleasant sensation or skin discoloration during use of the machine
on your hands once you stop working. Place an adequate work breaks. In disregard
of adequate work breaks, there may be a hand-arm vibration syndrome.

1. Parts location
1. Saw chain 7. Rear handle 13. Fuel tank
2. Guide bar 8. Air filter cover 14. Guide bar scabbard
3. Front hand guard 9. Lock nut 15. Choke knob
4. Primer bulb 10. Starter handle 16. Engine switch
5. Throttle trigger 11. Front handle 17. Spiked bumper
6. Throttle trigger lock lever 12. Oil tank 18. Clutch cover