Caladair ED-TOUCH Installation and operation manual

ED-TOUCH
TOUCH SCREEN REMOTE CONTROLLER
OPERATING AND COMMISSIONING INSTRUCTIONS
MS
-
REL
-
001
Ind
B
Maj. 20/06/2017
Créé par
: JC
Validé par
: AR
Pa e
1
/
8

ED-TOUCH
TOUCH SCREEN REMOTE CONTROLLER
OPERATING AND COMMISSIONING INSTRUCTIONS
MS
-
REL
-
001
Ind
B
Maj. 20/06/2017
Créé par
: JC
Validé par
: AR
Pa e
2
/
8
TABLE DES MATIERES
I. RECEIVING THE EQUIPMENT ................................................................................................................. 2
I.1. Checks on reception ...................................................................................................................... 2
I.2. Unpacking ...................................................................................................................................... 3
I.3. toring ............................................................................................................................................ 3
II. IN TALLATION ........................................................................................................................................ 3
II.1. IN TALLATION ................................................................................................................................ 3
II.2. Wiring ............................................................................................................................................. 3
II.2.a. CARMA ................................................................................................................................... 3
II.2.b. AQUAPACK – ELECTROPACK – NEOTIME – EVENTY - FREETIME ......................................... 3
II.2.c. EXAECO .................................................................................................................................. 4
II.3. Activation ....................................................................................................................................... 4
III. GENERAL OPERATION ........................................................................................................................ 5
III.1. Centrale operating : menu tree ..................................................................................................... 5
III.1.a. Écran 1 : Home scrren AHU in running opration ................................................................... 5
III.1.b. creen 2 : main menu ............................................................................................................ 6
III.1.c. creen 3 : Offset temperature ............................................................................................... 6
III.1.d. creen 4 : Extended operation .............................................................................................. 6
III.1.e. creen 5 : Information menu ................................................................................................. 7
III.1.f. Écran 6 : etting menu ........................................................................................................... 7
III.2. Unit stopped without alarm : menu Tree ...................................................................................... 7
III.3. Unit stopped due to a default : menu Tree ................................................................................... 8
IV. Use EDTOUCH as room setpoint ........................................................................................................ 8
V. Repair ..................................................................................................................................................... 8
I. RECEIVING THE EQUIPMENT
I.1. Checks on reception
When the equipment is received, the state of the packaging and the equipment must be checked. In the event of damage, make
an accurate note of any problems on the carrier's delivery note
SAFETY INSTRUCTIONS
In compliance with the current norms, the machine should be installed only by a technical person qualified for this type
of work.
Use the required personal protection devices so as to avoid injuries caused by electrical and mechanical hazards (injuries
by touching panels, sharp edges, etc.). Use EN170 protective eyewear and ear protection.
Do not use the unit for an other used which it designed. This unit can’t be use for extract or supply dangerous air.
Move the machine as given in chapter handling.
Grounding is carried out in compliance with current standards. Never start the device without grounding
Before any intervention ensure that device is powered off and wait for complete stop of every rotative component such as
damper, fan, rotative exchanger…
During device is running inspection doors must be mounted and closed.
Start is to be done only with padlockable swith.
Do not shut off or short circuit the safety and control equipment.
During interventions, be carefull with hot components such as hot water coil or electric resistances.
The machine should be installed in compliance with fire norms.
The waste must be disposed of in compliance with the current standards. No packaging should be discarded into the
environment.
We disclaim any responsibility for any damages resulting from wrong utilisation of the equipment, reparation,
modification or non compliance of these instructions.

ED-TOUCH
TOUCH SCREEN REMOTE CONTROLLER
OPERATING AND COMMISSIONING INSTRUCTIONS
MS
-
REL
-
001
Ind
B
Maj. 20/06/2017
Créé par
: JC
Validé par
: AR
Pa e
3
/
8
I.2. Unpacking
When the equipment is unpacked, check the following:
oThe total number of packages is present.
oAll accessories are present (dampers, roof, electric switchgear, etc.). After unpacking the equipment, the waste must
be disposed of in compliance with the current standards. No packaging should be discarded into the environment
I.3. Storing
The equipment must be stored in shade, in a dry place, at a temperature between -20°C and 40°C. The packaging can’t be
considered sufficient for an external storage. IP30
II. INSTALLATION
II.1. INSTALLATION
The Touch screen remote controller can be installed on a walla or a cabinet. Install ED-TOUCH such that bad weather or
ambient temperature cannot damage the internal items of the unit during installation as well as when used later.
II.2. Wiring
II.2.a. CARMA
II.2.b. AQUAPACK – ELECTROPACK – NEOTIME – EVENTYS - FREETIME

ED-TOUCH
TOUCH SCREEN REMOTE CONTROLLER
OPERATING AND COMMISSIONING INSTRUCTIONS
MS
-
REL
-
001
Ind
B
Maj. 20/06/2017
Créé par
: JC
Validé par
: AR
Pa e
4
/
8
II.2.c. EXAECO
II.3. Activation
For old unit (before 2016) you have to activate the ED-TOUCH. Please follow the procedure bellow.
On the display supplied with the unit, enter access right 1111.
In the menu configuration / communication :
o Enter function on port 2 : External screen
oEnter the kind of display connected on Port2 : ED-TOUCH
Configuration Communication Function port 2
External screen
External screen
connected to
Port 2
ED-TOUCH
Access right Enter Enter password 1111
Actual level : ADMIN

ED-TOUCH
TOUCH SCREEN REMOTE CONTROLLER
OPERATING AND COMMISSIONING INSTRUCTIONS
MS
-
REL
-
001
Ind
B
Maj. 20/06/2017
Créé par
: JC
Validé par
: AR
Pa e
5
/
8
III. GENERAL OPERATION
The ED-TOUCH is a user display and service display thanks emulator integrated into accessible via password.
III.1.Centrale operating : menu tree
As long as the unit is running normally, you will return to the home screen bellows. The logo in the upper left indicates the
menu where you are
III.1.a. Écran 1 : Home scrren AHU in running opration
Screen 1 : Home screen (see chapter
III.1.a)
Screen 2 : main menu (see chapter
III.1.b)
Screen 3 :
température OFFSET
(See chapter III.1.c)
Screen 4 : Extended
operation (see chapter
III.1.d)
Screen 5 : Information
(See chapter III.1.e)
Screen 6 :
Configutration (voir
chapitre III.1.f)
Date and Hour.
Automatically
WINTER/SUMMER update
Display ED-TOUC temperature
sensor. Possibility to display
setpoint temperature (settable
only via E-TOOL)
Display outdoor temperature
(sensor connected to the unit)
Access to main menu
Access to alarm wich not stop
unit. Ex : Dirt filter

ED-TOUCH
TOUCH SCREEN REMOTE CONTROLLER
OPERATING AND COMMISSIONING INSTRUCTIONS
MS
-
REL
-
001
Ind
B
Maj. 20/06/2017
Créé par
: JC
Validé par
: AR
Pa e
6
/
8
III.1.b. Screen 2 : main menu
III.1.c. Screen 3 : Offset temperature
III.1.d. Screen 4 : Extended operation
Note : The extended operation overrides clocks. If at the end of the extended opration, the clock is activate, so the unit continue
to run.
Possibility to OFFSET
setpoint +/- 3 °C. (range of
OFFSET settable only via E-
tool)
Return to the home screen
Possibility to forced unit in
high speed during 1-2-3
hours.
Stop extended operation ? The
unit will be in AUTO MODE.
Return to the home screen
Possibility to set the hour to
stop unit.
Return to the home screen
Acces to OFFSET menu
Acces to extended operation menu
Access to information menu
Access to configuration menu

ED-TOUCH
TOUCH SCREEN REMOTE CONTROLLER
OPERATING AND COMMISSIONING INSTRUCTIONS
MS
-
REL
-
001
Ind
B
Maj. 20/06/2017
Créé par
: JC
Validé par
: AR
Pa e
7
/
8
III.1.e. Screen 5 : Information menu
III.1.f. Écran 6 : Setting menu
Use this menu to access to the emulator (complete Tree of the unit). See unit instruction to know details. (Password 3333).
III.2.Unit stopped without alarm : menu Tree
As long as the unit is stopped without alarm, you will return to the home screen bellows. The logo in the upper left indicates
the menu where you are
Return to the home screen
Possibility to enter phone
number. This number will
appear if an alarm stop the
unit (Password 3333)
Possibility to acces to the
main information about the
unit. (password 3333)
Return to the home screen
Date and Hour.
Automatically
WINTER/SUMMER update
.
Access to main menu (voir
chapitre III.1.b)
Access to extended operation
menu (voir chapitre III.1.d)
Display the reason of stop

ED-TOUCH
TOUCH SCREEN REMOTE CONTROLLER
OPERATING AND COMMISSIONING INSTRUCTIONS
MS
-
REL
-
001
Ind
B
Maj. 20/06/2017
Créé par
: JC
Validé par
: AR
Pa e
8
/
8
III.3.Unit stopped due to a default : menu Tree
As long as the unit is stopped without alarm, you will return to the home screen bellows. The logo in the upper left indicates
the menu where you are
IV. Use EDTOUCH as room setpoint
ED-TOUCH can be used as room sensor for room control. To activate this function :
oAccess to the emulator (screen 2)
Follow the unit instruction to change the temperature control mode.
You have to select : Room control
V. Repair
oNothing display on screen : verify connections on C+ et G0
oDisplay not connected see in red on Touch screen : Verify connections on A et B
Access to the alarm list via
emulator
Display phone number to call if
an alarm stopped unit.