CAM62 CA101 User manual

監錄易(監控錄影設備專門店) http://www.cam62.com User manual
http://www.CAM62.com
CA101 / CA111 / VI8908 / VI8908W
IP Wireless / Wired Camera
REMOTE PAN / TILT ROTATE
User Manual
CA101 CA111 VI8908 VI8908W
1 WELCOME
This model IP Camera is an integrated wireless IP Camera solution. It combines a high quality
digital Video Camera with network connectivity and a powerful web server to bring clear to
your Desktop from anywhere on your local network or over the Internet.
The basic function of it is transmitting remote video on IP network. The high
Quality video image can be transmitted with 30fps speed on the LAN/WAN by using
MJPEG hardware compression technology.
This is based on the TCP/IP standard. There is a WEB server inside which could Support
Internet Explore. Therefore the management and maintenance of your device become more
simply by using network to achieve the remote configuration, start-up and upgrade firmware.
You can use this IP CAMERA to monitor some special places such as your home and your
office. Also controlling and managing images are simple by clicking the website through The
network.
NOTE: you can use the IP Camera Step by Step .

監錄易(監控錄影設備專門店) http://www.cam62.com User manual
Features
Powerful high-speed video protocol processor
High-sensitivity 1/4 CMOS sensor
Picture Total 300k Pixels
Video Frame Rate:30fps(QVGA), 30fps(VGA)
Resolution:640 x 480(VGA), 320 x 240(QVGA)
Light Frequency:50Hz, 60Hz or Outdoor
Optimized MJPEG video compression for transmission
Multi-level users management and passwords definition
Embedded Web Server for users to visit by IE
Support wireless network (WiFi/802.11/b/g)mobile
Supporting Dynamic IP(DDNS)and UPNP LAN and Internet(ADSL, Cable Modem)
Giving alarm in cause of motion detection
Supporting image snapshot
Support multiple network protocols：HTTP，TCP/IP，UDP，STMP，DDNS，SNTP，
DHCP，FTP
Support remote system update
Advanced Features
Multi-Protocol support and Transportation
IP CAMERA supports Multi-Protocol such as TCP/IP, SMTP and HTTP. Sending the image
to your mailbox automatically when the IP CAMERA is triggered.
Video Image PTZ function
Users can control the camera direction on the video image.
Motion Detection
Your may use the internal Motion Detection function or external sensor to trigger
images Recording and transportation. Alarm sensor input/output.
The detection sensor sends an alarm and records by itself when there is a fire or
accident. A message as an email is sending to you by this sensor,(The input/output
discreteness can be chosen)
DDNS support
Using it in the condition which includingADSL and IP change often is more convenient,
because IP CAMERA provides dynamic DNS function.
Advanced User Management
Only allowing authorized users access to real-time images of IP Camera.

監錄易(監控錄影設備專門店) http://www.cam62.com User manual
1.2 Packing List
Untie the packing and checking the items contained against the following list;
Wireless IP Camera 1
Wi-Fi Antenna 1
DC Power Supply 1
Network Cable 1
Mounting bracket 1
NOTE: Contact us immediately in the case of any damaged or short of
contents.
1.3 Product views
1 Infrared LED
2 LENS CMOS sensor with fixed focus lens.
3 Network Indicator LED
4 Mic
5 Antenna
6 LAN: RJ-45/10-100 Base T
7 DC5V: Power supply
RESET BUTTON:press and hold down the RESET BUTTON for 5
Seconds .Release the power button and IP Camera will be reset back to the factory
default Parameter.

監錄易(監控錄影設備專門店) http://www.cam62.com User manual
1.4 PC System Requirements
System configuration requirements :( Example for view four IP Camera)
CPU: 2.06GHZ or above Memory: 256M or above
Network Card: 10M or above Display Card:64M or above memory
Recommendable Operating system: Window2000 or Window XP or Vista
1.5 Hardware Instruction
Follow the steps below to set up your camera hardware. Make sure to follow each
step carefully to ensure that the camera operates properly
1) Plug the network cable into the camera and then into your Cable/DSL router.
2) Plug the power adapter into the camera and then into the power outlet.

監錄易(監控錄影設備專門店) http://www.cam62.com User manual
1 SOFTWARE OPERATION SETTING
2.1 IP Camera DevFind Tool
Software Download Site : http://www.cam62.com/article.php?id=73
When the Device has been mounted properly, you can double click the Icon “IP Camera
DevFind Tool” and a dialog box as will pop up.
Note: The software searches IP Servers automatically over LAN.
There are 3 cases:
1. No IP Cameras found within LAN.After about 1 minute search, the Result Field will
show “not found IP Server” and the program shut automatically.
2. IP Cameras have been installed within LAN. All the IP Cameras will be listed and the
total number is displayed in the result field as shown in

監錄易(監控錄影設備專門店) http://www.cam62.com User manual
3. The IP Cameras installed within LAN do not share the same subnet with the monitoring
PC. A prompt as shown in result field (prompt: Subnet doesn’t match, double click to
change!).
Click the left mouse button to choose the prompt and click the right mouse, choose
Network Configuration to set the IP address of the Camera to the same subnet as LAN.
zBasic Properties
There are some device information in the Basic Properties, such as Device
ID,System Firmware Version, Web UI Version.
zNetwork Configuration
In this page, you can configure the Network parameter.
IP : Fill in the IP address assigned and make sure it is in the same subnet as the
gateway (i.e. the first three sections are the same)
Sub Mask: The default subnet mask of the equipment is: 255.255.255.0
Gateway: Make sure it is in the same subnet with PC IP address .Default
Gateway address is 192.168.1.1
DNS: IP address of IPS network provider.
HTTP Port: LAN port assigned for the equipment, usually 100
User & Password: Default administrator Username:admin No Password
Enable Using DHCP the system will assign a reasonable IP address for your
equipment. Only if your gateway supports DHCP (It is the case with most
gateways).
NOTE: When the prompt “subnet doesn’t match, double click to change!” please
set the IP Camera IP address once again.

監錄易(監控錄影設備專門店) http://www.cam62.com User manual
2.2 Camera Login
You can access the camera through IP Camera Tool or IE directly.
1) Double click the IP address of the IP Camera listed.
2) To access the camera ,start your web browser and type in the camera’s IP
address
Such as http://192.168.1.100:100
3) The Camera Login page pop-up.
Enter your account and password on the login page as shown in By default,
Administrator’s Username:admin No Password Click “Sign in” to enter the monitoring
page. You can set the username and password as Administrator, Operator or Visitor.

監錄易(監控錄影設備專門店) http://www.cam62.com User manual
2.3 For Visitor
The status of 9 routes, as shown below.
For example: if is bright, the first route is on Detection (Motion Detection).
If you want to detect 4 views, need to click this icon
If you want to detect 9 views, need to click this icon
Î
OSD: Display date and time on the video .You can disable the OSD function or choice
Other color, (OSD: on-screen display)
Reversal: To see the reversal image
Mirror: To see the mirror image.
Add time stamp on record: Increase the video time stamp
PLAY: Click icon into play mode, is stop.
Snapshot: Click icon to snap the picture.

監錄易(監控錄影設備專門店) http://www.cam62.com User manual
AUDIO: Click icon Camera MIC open, Local Voice input
TALK: Click icon Camera Speaker open, Remote Voice Output
RECORD: Click icon into REC mode, is stop.
2.4 For operator
When login as operator administrator, you can enter the IP Camera For Operator
Vertical patrol
Horizontal patrol
Stop patrol
IO output Switch on/off. (See 2.5.5 for more informations)

監錄易(監控錄影設備專門店) http://www.cam62.com User manual
Resolution: VGA (640*480) / QVGA (320*240)
Work mode: 50Hz/60Hz/Outdoor
Color parameter: Click or can adjust the brightness and contrast
Image PTZ function: Image PTZ function is recommended, you can control the camera
Direction on the video image. Double click the right mouse on the image to enable PTZ
and you can see a white arrow on the video image, click left mouse to control
direction. If want to cancel, double click right mouse again.
2.5 For Administrator
When you login as administrator, “For Administrator” is enabled.
Multi-Device Settings
Î
zUse multiple cameras in LAN
In the Multi-Device Settings page, you can see all devices searched in LAN. The 1st
Device is this device default. You can add more cameras list in LAN for monitoring .This
Web software Supports up to 9 IP Cameras online simultaneously.

監錄易(監控錄影設備專門店) http://www.cam62.com User manual
zUse multiple cameras with a single IP address
In the Multi-Device Settings page .You can use multiple camera with a single IP address
by configuring different ports for each camera .By default, the Device uses port 100 for
accessing the camera’s homepage and video streaming.
Adding a second camera:
If you decide to add a second IP camera, you will need to change the port number for the
second camera.
Camera#2: LAN IP address is 192.168.1.101-Port 101
Will be forwarded to: http://192.168.1.101:101
Note that Camera #2 has a different IP address and a different port number. The LAN IP
address is assigned by the router, but the port number is not one you will need to
configure the port number. Once you have changed the port number for the camera and
the settings in your router, you can access the second camera from the Internet by
http://192.168.1.101:101
Adding more cameras:
If you decide to add more cameras, you will need to change the port number for the other
cameras, such as 101,102,103. To access these cameras from the Internet, you would
use: http://192.168.1.102:102

監錄易(監控錄影設備專門店) http://www.cam62.com User manual
zUpgrade Device Firmware
Upgrade Device Firmware and device embedded web UI software in this page.
zRestore Factory Settings
Restore factory settings of the device.
zReboot Device
Reboot the device.

監錄易(監控錄影設備專門店) http://www.cam62.com User manual
2.5.1 Network Settings
Î
zBasic Network Settings
If the router and the IP camera connect has DHCP function, you can choose “Obtain IP
from DHCP Server” else fill in the network parameters manually.
Http Port: In most cases, you can leave this value as however, if your Internet Service
Provider blocks this port, you may switch to another port number such as 85.

監錄易(監控錄影設備專門店) http://www.cam62.com User manual
zWireless Lan Settings
Please enter the wireless net setting page of the wireless Router to out SSID, Channel,
Encryption, Authentication.
zADSL Settings
When connected to the Internet through ADSLdirectly, you can enter the ADSL username
And password obtained from ISP.

監錄易(監控錄影設備專門店) http://www.cam62.com User manual
zUPNP Settings
If you access IP Camera, to be make sure UPNP Status is Succeed.
UPNP Protocol settings, as Figure below:
2.5.2 DDNS Service Settings
DDNS Service: The system support protocols from some DDNS providers: Dyndns.org.
User and Password: the user name and password used when applying for the domain
name.
DDNS Host: the Domain Name
DDNS or Proxy port: If you access the DDNS host through a proxy, you should input the
Proxy IP
DDNS or Proxy Port: Proxy Port

監錄易(監控錄影設備專門店) http://www.cam62.com User manual
2.5.3 Other Service Settings
Î
Configure the E-mail box to receive and send mails. The E-mail box is used for receiving
the images sent after alarm and the system IP address after successful dial-up.
Mail Service Settings
Settings the FTP Service:

監錄易(監控錄影設備專門店) http://www.cam62.com User manual
zAlarm Service Settings
Enter Alarm Service Settings page to configure Motion Detection function.
Motion Detect Armed
When you enable motion detect armed, the camera can be triggered to send email alerts
sound you will hear.
Motion Detect Sensibility
You can choice High, Medium, Low
I/O PINS: 1 Output (+5V) 2 Output 3 Alarm input 4 Input (GND)
Alarm Input Armed
Input pins: The input pins can be used for 1-way external sensor input For example; you
may connect a person Infrared Sensor (PIP) to it for motion detection. When external
sensor triggered,
IP CAMERAcan be programmed to send an email with picture or control the internal relay
output.
If you link an external alarm with Pin3 and Pin4, when enable alarm input armed ,external
alarm is enabled
IO Linkage on Alarm
Enable IO linkage on alarm, Pin 1 will output +5V when alarm triggered, and output LOW
when alarm release automatically.
Switch on/off buttons control Pin1 output manually.
Send Mail on Alarm
Sent picture and mail inform to customer’s e-mail after alarmed. (Firstly you should finish
the Mail Service Settings.)
Upload Image on Alarm
Enable upload image on alarm and set upload interval (Seconds).
REC automatically and save to PC
When you enable motion detect and open the camera monitoring page on the PC. If there
is an alarm triggered, REC will start automatically for several seconds and save to the PC.

監錄易(監控錄影設備專門店) http://www.cam62.com User manual
zPath Settings
Setting the path of preserve video, when start record video, click , and the
video file will be preserved in the specified directory Record Path. As below figure:
2.5.4 System
Î
zDevice Info
You can find the information about Device ID, Firmware Version and Embedded Web UI
Version.

監錄易(監控錄影設備專門店) http://www.cam62.com User manual
zAlias Settings
You can Input the new name as you like.
zDate &Time Settings
Data &Time Settings page.

監錄易(監控錄影設備專門店) http://www.cam62.com User manual
zUsers Settings
Eight accounts are acceptable for this system. Here the eight users can
Configure their user names and password as administrator, Operator or Visitor.
zVisitor: In this mode, you can only view.
zOperator: You can control the direction of IP Camera and set some
parameter.
zAdministrator: You can setup the advanced configurations of the IP
Camera.
HOW TO USE
2.6 Step by step to use
Follow the instructions below to get started after the Camera has been mounted properly.
When the IP camera powered on, it will rotate itself and stop to the center.
1) Use Network cable connect IP Camera to LAN.
2) Enter IP Camera DevFind Tool to set the basic configuration,
3) When IP address of the Camera listed in the Result Field of the IP Camera DevFind
Tool, it means the basic configuration is completed.